Upload
ankur-vagh
View
179
Download
8
Tags:
Embed Size (px)
Citation preview
Engineering Graphics
Presents BY
A.S.VAGH
M.Tech (IPED) , B.E. Mechanical, PGDIM
E-mail Id: [email protected]
Lines
07/05/2015A.S.VAGH
1
23 4
5
6
7
8
9
10
14
13
12 11
Viewing-plane line
Extension lineDimension Line Center Line
Hidden Line
Break Line
Cutting-plane Line
Visible Line
Center Line (of motion)
Leader
VIEW B-BSECTION A-A
Section Line
Phantom Line
07/05/2015A.S.VAGH
Horizontal Lines
07/05/2015A.S.VAGH
Vertical Lines
07/05/2015A.S.VAGH
Inclined Lines
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
Parallel Lines
07/05/2015A.S.VAGH
Perpendicular Lines
07/05/2015A.S.VAGH
Circles and Arcs
07/05/2015A.S.VAGH
Drawing a circle of a given
diameter with a compass
07/05/2015A.S.VAGH
Use of the French Curve
07/05/2015A.S.VAGH
Guidelines for Lettering
For uniformity, all letters should be the same height,
proportion and inclination. A necessary tactic for
maintaining uniformity is the use of guidelines.
07/05/2015A.S.VAGH
Guidelines for Lettering
Ascender is the part of the lowercase letter that extends
above the body of the letter.
Descender is the part of the lowercase letters that
extends below the body letter.
07/05/2015A.S.VAGH
Lettering
Writing titles, dimensions, notes and other important
particular on a drawing is called lettering.
Lettering should be done properly in clear,
understandable & uniform style.
It should be in plain & simple style so that it could be
done free hand & speedily.
Note: Use of drawing instruments in lettering takes
considerable time and hence, it should be avoided
efficiency in the art of lettering can be achieved by careful
& continuous practice.
07/05/2015A.S.VAGH
Lettering
The size of letter is specified by its height.
Generally the ratio of height to width for most of the
capital letters are taken as 6:5 and for most of the
lower case letters are taken as 4:4.
Main letter are generally written in 10 mm to 12 mm
Subtitle is written in 3 mm to 6 mm
Notes, Dimension fig etc. written in 3 mm to 4 mm.
Space between the words is generally 2 to 5 mm in
lettering.
Inclined latter write in an inclination of 750.
07/05/2015A.S.VAGH
Lettering
1) Single Stroke Latter
a) Vertical
b) Inclined
2) Gothic Letter
07/05/2015A.S.VAGH
Lettering
1) Single Stroke Latter -Vertical
07/05/2015A.S.VAGH
Lettering
1) Single Stroke Latter -Vertical
07/05/2015A.S.VAGH
Lettering
1) Single Stroke Latter -Vertical
07/05/2015A.S.VAGH
Lettering
1) Single Stroke Latter -Vertical
07/05/2015A.S.VAGH
Lettering
1) Single Stroke Latter - Inclined
07/05/2015A.S.VAGH
Dimensioning
Every drawing, whether a scale drawing or a freehand
drawing, besides showing the true shape of an object,
must supply its exact length, breadth, height, sizes and
positions of holes, grooves etc. and such other details
relating to the manufacture of that object. Supplying
this information on a drawing is called Dimensioning.
Lines, figures, numerals, symbols, notes etc. are used
for this purpose.
07/05/2015A.S.VAGH
Dimensioning terms & notations
Dimension line: Thin continuous line. It is terminatedby arrowheads touching the outline, extension linesor Centre lines.
Extension line: Thin continuous line drawn inextension of an outline. It extend by about 3 mmbeyond the dimension line.
Arrow head: Placed at each end of dimension line.Touch outline, extension line or Centre line. Lengthof arrowhead should be three times it max width. Thespace betn them is nearly filled up.
Leader: Thin continuous line connecting a note ordimension fig with future.
07/05/2015A.S.VAGH
Dimensioning terms & notations
07/05/2015A.S.VAGH
Arrow heads
1. Open (900)
2. Open (200)
3. Closed
4. Closed and Filled
07/05/2015A.S.VAGH
Method of Indicating Dimension
(Aligned System)
Oblique Angular
07/05/2015A.S.VAGH
Method of Indicating Dimension
(Uni-directional System)
Angular
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
Dimensions
Shape Identification Symbols
07/05/2015A.S.VAGH
Arrangement of Dimensions
1. Chain Dimension:
2. Parallel Dimension:
07/05/2015A.S.VAGH
Arrangement of Dimensions
3. Super Imposed Continuous (Less Space) Dimension:
4. Combined (Chain & Parallel) Dimension:
07/05/2015A.S.VAGH
Arrangement of Dimensions
5. Co-ordinate Dimension:
6. Dimensioning of diameters:
07/05/2015A.S.VAGH
Arrangement of Dimensions
7. Dimensioning of chords, arcs and angles:
8. Dimensioning of Radius:
07/05/2015A.S.VAGH
Arrangement of Dimensions
9. Dimensioning chamfers:
10. Dimensioning countersunks:
07/05/2015A.S.VAGH
Arrangement of Dimensions
11. Dimensioning Screw Thread:
12. Dimensioning Taper Future:
07/05/2015A.S.VAGH
Notes in Dimensions
Notes should always be written horizontally in capital
letters and begin above the leader line and may end
below also.
Further, notes should be brief and clear and the wording
should be standard in form.
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
BIS–SP 46
BIS is the National Standards body formed by thegovernment of India on 1 April 1987, replacing ISI existingearlier.
The objective of BIS is to develop the industries andcommercial growth of the country by developing globallyacceptable standard for product.
It works in association with other standard-developingorganization worldwide, in particular with the ISO.
BIS has recommended & published various standards fortechnical drawings.
These standards are available in the form of IS code andSpecial Publication 46: 2003.
07/05/2015A.S.VAGH
BIS–SP 46
These standards are available in the form of IS code and
Special Publication 46: 2003.
In short,
The standard which is for “Engineering
Drawing Practice For Schools & Colleges”.
And used in the educational institution for
engineering drawing or graphics.
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH
1
2
3
4
5
6
7
8
9
10
BA
D
C
1
23
4
5
6
78
9
10
Steps:
1. Draw both axes as perpendicular bisectors
of each other & name their ends as shown.
2. Taking their intersecting point as a center,
draw two concentric circles considering both
as respective diameters.
3. Divide both circles in 12 equal parts &
name as shown.
4. From all points of outer circle draw vertical
lines downwards and upwards respectively.
5.From all points of inner circle draw
horizontal lines to intersect those vertical
lines.
6. Mark all intersecting points properly as
those are the points on ellipse.
7. Join all these points along with the ends of
both axes in smooth possible curve. It is
required ellipse.
Problem 1 :-
Draw ellipse by concentric circle method.
Take major axis 100 mm and minor axis 70 mm long.
ELLIPSE
BY CONCENTRIC CIRCLE METHOD
07/05/2015A.S.VAGH
07/05/2015A.S.VAGH