Upload
h-g-baron
View
1.391
Download
9
Embed Size (px)
Citation preview
HERVE BARON
© 2015 – Hervé Baron
Welcome to this assessment
It will test you general knowledge as a Project Engineer.
Enjoy!
Comments are most welcome ([email protected]), which I will incorporate for the benefit of all.
Hervé
Project Engineer knowledge test
HERVE BARON
© 2015 – Hervé Baron
Hazard area classification is defined in the Engineering design basis.
Right or Wrong?
Project Engineer knowledge test
HERVE BARON
© 2015 – Hervé Baron
Hazard area classification is defined in the Engineering design basis.
Wrong. Only the code to be applied, e.g., API, to calculate the extent of the hazardous area, is defined in the Engineering design basis. The zone area determined as part of the HSE design.
Project Engineer knowledge test
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
On which revision of the P&IDs is based the first purchase of Piping materials?
1st issue
2nd issue
3rd issue
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
On which revision of the P&IDs is based the first purchase of Piping materials?
1st issue
2nd issue (IFD)
3rd issue
Extract from The Oil & Gas Engineering Guide, Editions Technip, 2nd Edition, page 120
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which documents are needed to elaborate the plot plan:
Equipment data sheets
P&IDs
PFDs
Equipment list
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which documents are needed to elaborate the plot plan:
Equipment data sheets
P&IDs
PFDs
Equipment list
Extract from The Oil & Gas Engineering Guide, Editions Technip, 2nd Edition, page 206
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which document(s) show(s) the capacity of Process equipment:
the Equipment list
the PFD/HMB
the Mechanical data sheet
the Process data sheet
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which document(s) show(s) the capacity of Process equipment:
the Equipment list
the PFD/HMB
the Mechanical data sheet
the Process data sheet
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What % of Isometrics are required to effectively start Piping pre-fabrication?
10%
30%
50%
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What % of Isometrics are required to effectively start Piping pre-fabrication?
10%
30%
50%
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What % of Piping materials must be delivered for Piping pre-fabrication to effectively start?
25%
50%
70%
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What % of Piping materials must be delivered for Piping pre-fabrication to effectively start?
25%
50%
70%, all diameters, grades and types (pipes, fittings, o-lets, etc.)
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
The HAZOP looks at the consequence of failures of:
equipment
safeguards
operator
control devices
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
The HAZOP looks at the consequence of failures of:
equipment
safeguards
operator
control devices
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which of the following is true of a Pre-FEED
Is sometimes called “Select phase”
Considers options in the basic configuration
Focuses on a single design
Is also called “Basic Engineering”
Consists of Process engineering only
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which of the following is true of a Pre-FEED
Is sometimes called “Select phase”
Considers options in the basic configuration
Focuses on a single design
Is also called “Basic Engineering”
Consists of Process engineering only
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
In which document do you find the flash point and auto-ignition temperature of a product?
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
In which document do you find the flash point and auto-ignition temperature of a product?
The MSDS (Material Safety Data Sheet)
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What type of check is called "squad check"
the cold eye review
the inter-disciplinary check
the Company review
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What type of check is called "squad check"
the cold eye review
the inter-disciplinary check
the Company review
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Civil guide drawings are issued at FEED stage.
Right or Wrong?
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Civil guide drawings are issued at FEED stage.
Wrong. They are issued as part of detail design. They show all input data (loads, dimensions, position of anchor bolts) for civil detail design.
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which load is taken into account in the consumers list for pumps?
absorbed power at normal flow
absorbed power at design flow
motor nameplate (rated) power
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which load is taken into account in the consumers list for pumps?
absorbed power at normal flow
absorbed power at design flow
motor nameplate (rated) power
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What is the number of manhours required for the first issue of each P&ID?
30
100
200
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
What is the number of manhours required for the first issue of each P&ID?
30, indeed, P&IDs are more or less the same from one job to the other
100
200
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which is the pre-requisite to issue the Plot Plan for design (IFD revision)
First 3D model review completed
Equipment size confirmed by Vendors
HAZOP review completed,
P&ID issued for design,
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Which is the pre-requisite to issue the Plot Plan for design (IFD revision)
First 3D model review completed
Equipment size confirmed by Vendors
HAZOP review completed,
P&ID issued for design,
Extract from “The Oil & Gas Engineering Guide”, Editions Technip, 2nd Edition, page 149
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
On which revision of the Civil Area drawings are the following items Approved For Construction (AFC)?
IFC1 (first) IFC2 IFC3 IFC4 (final)
Secondary sewers
Paving
Pipe supports
Secondary cable routing
Foundations
Pressurized Piping
Gravity piping
Main cable routing
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
On which revision of the Civil Area drawings are the following items Approved For Construction (AFC)?
IFC1 (first) IFC2 IFC3 IFC4 (final)
Secondary sewers x
Paving x
Pipe supports x
Secondary cable routing x
Foundations x
Pressurized Piping x
Gravity piping x
Main cable routing x
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Ref.: The Oil & Gas Engineering Guide, Editions Technip, 2nd Edition, page 102
HERVE BARON
© 2015 – Hervé Baron
Project Engineer knowledge test
Where goes each drain?
Ref.: The Oil & Gas Engineering Guide, Editions Technip, 2nd Edition, page 100
© 2015 – Hervé Baron
HERVE BARON
The Oil & Gas Engineering Guide - 2nd edition
A unique synthesis for the busy Project professional 270 pages 300 illustrations
Interested and wanting to know more on Engineering?
© 2015 – Hervé Baron
HERVE BARON
The Oil & Gas Engineering Guide 2nd edition
Please note that it will take weeks before the book is on Amazon... but you can already purchase it from the publisher.
Up to March 30th there is a 25% discount
Please go to:
http://www.editionstechnip.com/en/catalogue-detail/1111/oil-gas-engineering-guide-the.html