ZXDSL 9210 Commissioning Manual

Basic Command 1. Login :2. edsl

Password: edsl Login to the ZXDSL CLI console, default username is edsl and the password is edsl.

3. DSL#Show card Show all of the card and their status on the ZXDSL 9210

4. DSL# erase Delete all of the configuration that contain on the ZXDSL 9210. Please be careful to used this command, because it’s will erased all of the configuration on your system.

5. DSL#reboot Reboot the ZXDSL 9210 and restart all of the board. Please be careful to used this command, because it’s will restart all of the board and the system will be down for a few second.

Change the ZXDSL 9210 Inband MAC address and identifier board 6. DSL#enable

Password : zxedsl DSL$ debug module 12345DSL$ debug module 888999 p1 00:d0:d0:00:00:01 DSL$ disableDSL#reboot This command used only if you are necessary to change the inband MAC address, if you first time build the ZXDSL 9210 network with more than one DSLAM please make sure there are no conflict MAC address on the each Network element(NE) on the same network. After you’re change this MAC address it’s will be take the effect after you’re reboot the system. After you change the MAC address and reboot the system, make sure the inband MAC address is already changed by type :DSL# show ip subnet

7. DSL#config card slot 1 cardtype EICG8. DSL#config card slot 3 cardtype ATIGN

Enable the PVLAN mode and initialize the uplink port 9. DSL#Configuration

DSL(config)#pvlan-mode enable enable the pvlan modeDSL(config)#pvlan-mode uplink_port 1/1 initialize the uplink portDSL(config)#pvlan-mode uplink_port 1/2 initialize the uplink portDSL(config)#pvlan-mode uplink_port 1/3 initialize the uplink portDSL(config)#ExitDSL#Copy running-config startup-config Save and commit all of the config

DSL#reboot after you’re enable the pvlan mode, it’s will be take the effect after you’re reboot the system

Add the Inband IP Address to the ZXDSL 9210 10. DSL#Configuration

DSL(config)#IP subnet 150.168.0.2 255.255.254.0 name dslam1DSL(config)#exitDSL#And then to make sure the IP address already adding to the ZXDSL 9210 type:DSL#Show ip subnet

Add the Vlan and put the port into the Vlan11. DSL#configuration

DSL(config)#add-vlan 2 add vlan 2DSL(config)#add-vlan 3 add vlan 3DSL(config)#vlan 2 1/1 tag put port 1/1 as an uplink to the switch into vlan 2 as a management vlan and tag it DSL(config)#vlan 3 1/1 tag put port 1/1 as an uplink to the switch into vlan 3 as a PPPoe vlan and tag it And then make sure the vlan are already exist and the port are already exist on the vlan by type:DSL#Show vlan show all the vlan that already exist on the systemDSL#Show vlan 2 show all the port(tag or untag) that are already exist on the vlan 2 DSL#Show vlan 3 show all the port(tag or untag) that are already exist on the vlan 3

Configure the adsl user on the ATIGN board 12. DSL#configure slot adsl 3

DSL(cfg-slot-adsl-3)#trap control enable to make if the subscriber in this board is on and then this board will know itDSL(cfg-slot-adsl-3)#no shutdownDSL(cfg-slot-adsl-3)#exitDSL(config)#vlan 3 3/1-32 untag put the subscriber port into the vlan 3 as a subscriber vlan and untag itDSL(config)#slot adsl 3 DSL(cfg-slot-adsl-3)#pvid 3 because of we configure the ADSL subscriber as an untag port so we need to add the pvidDSL(cfg-slot-adsl-3)#atm pvc 8:81 configure the PVC(VCI/VCI) into the subscriber board DSL(cfg-slot-adsl-3)#exitDSL(config)#show atm vc slot 3 make sure the PVC are already exist at the subscriber board

Create the ADSL profile and apply the profile to the ADSL subscriber

13. DSL(config)#adsl-profile adsl512k this fist command is to created your profile. And then System will ask you this profile didn’t created before, are you sure want to create this profile? You should answer yes.DSL(config)# adsl-profile adsl512k the second command is to configure your profile. And then system will ask you to input all of your configuration, but the most important you should configure the uplink and downlink rate: Downlink rate :

Atuchan conf fast max Tx rate [0-132040] (Def:8128) : 512 Atuchan conf interleave max Tx rate [0-132040] (Def:8128) : 512

Uplink rate:Aturhan conf fast max Tx rate [32-1536] (Def:1024) : 512 Aturhan conf interleave max Tx rate [32-1536] (Def:1024): 512

And then to make sure your ADSL profile is already created successfully type:DSL#Show adsl profile show all adsl profile DSL#Show adsl profile adsl512k show detail the adsl512k profileDSL(config)#interface adsl 3/1 enter the adsl slot 3 port 1 to configure itDSL(cfg-if-adsl-3/1)#adsl profile adsl512k apply the profile to adsl portDSL(config)#slot adsl 3 enter the adsl slot 3 to configure itDSL(cfg-slot-adsl-3)#adsl profile adsl512k apply the profile to adsl slot

Configure the ZXDSL 9210 SNMP server 14. DSL(config)#snmp-server host 10.10.10.1 private initialize the snmp server ip

address to the ZXDSL 9210DSL#show snmp show the snmp server ip address that you’re already initialize to the ZXDSl 9210DSL(config)#ip route 0.0.0.0 0.0.0.0 192.168.0.1 add the static route to the ZXDSL 9210. This command is used only if the SNMP server Ip address is not in the same network segment with the ZXDSL 9210 ip address.

Configure Uplink port with the STP(Spanning tree protocol) features 15. for example we want to configure the EICG board port 1 on the slot 1 and 2 as an

uplink port with the STP features where EICG slot 1 port 1 and EICG slot 2 port 1 will be as a redundant uplink port.DSL#show spanning-tree to show the STP features on the ZXDSL 9210 is already enable or not, if the status of STP is disable you should be enable it by type:DSL#Config spanning-tree enable enable the STP features on the systemDSL#show spanning-tree make sure the STP features on the system is already enable. And please chack the priority on this STP, the value of priority should be less then the priority value on the switch (Ethernet aggregator). DSL#config interface Ethernet 1/1 enter EICG slot 1 port 1 to configure it DSL(cfg-if-eth-1/1)#spanning-tree enableenable the STP features on the EICG slot 1 port 1. DSL(cfg-if-eth-1/1)#show spanning-tree interface 1/1 make sure the STP features on the slot 1 port 1on is already enable

DSL#config interface Ethernet 2/1 enter EICG slot 2 port 1 to configure it DSL(cfg-if-eth-2/1)#spanning-tree enableenable the STP features on the EICG slot 2 port 1. DSL(cfg-if-eth-2/1)#show spanning-tree interface 2/1 make sure the STP features on the slot 2 port 1on is already enable

After you are already configure the STP features in both of port, you should be check the status of link in this port.DSL(cfg-if-eth-1/1)#show spanning-tree interface 1/1 look the status of STP, there are 3 kind of status on this STP port :1. blocking means the port is blocking and can’t transfer the packet2. learning means the port still learning the other port, please waiting for a

few minutes.3. forwarding means the STP port is already active and ready to transfer the

packet.DSL(cfg-if-eth-1/2)#show spanning-tree interface 1/2 look the status of STP, the normal condition if port(1/1) and port (1/2) both of them as an STP port, one of them will be blocking and one of the other will be forwarding.