1
What’s new NX10
Fundamental
2
New NX look
Siemens PLM Software มการปรบเปลยนรปแบบ User Interface ใหมความเหมาะสม
สามารถเลอกใชธมดงตอไปนเปนคาเรมตน
Light
Light Gray
สามารถเรยกค าสงไดท
Command Finder User Interface Preferences
Location in dialog box Theme node→NX Theme group→Type list→Light or Light Gray
Help and search enhancements
NX Help อยในรปแบบ web application
3
การปรบปรง : NX Help Search แบบใหมไมตองการ Java applets ดงนนไมตองกงวลกบปญหาการใชงานจาก Java security
updates การคนหารวดเรวและใชงานงายขน
o คนหาจากขอบเขตของเนอหา o แสดงจ านวนผลลพธในแตละหวขอ สามารถเลอกกรองขอมลเฉพาะในหวขอทตองการ
ใช NX Help รวมกนหลาย user ได
Note NX Help รองรบหลาย user ดวยการใช intranet.
สามารถเรยกค าสงไดท
Command Finder Help
Resource bar enhancements
ใชเมน Resource Bar Options ซงวางอยทดานบนซายของ Resource bar ควบคมต าแหนง, ลกษณะการแสดงผล และสวนประกอบบน Resource bar
Tip ถาตองการซอน tab หรอยายต าแหนง navigator หรอ palette ให right-click ท tab และเลอก option ทตองการ ถาตองการแสดง tab ทซอนอย right-click ตรงทวางบน Resource bar แลวเลอก tab
Customize line widths
สามารถปรบคณสมบตของความหนาเสนไดตามตองการ
สามารถเรยกค าสงไดท
Command Finder Customer Defaults
Location in dialog box
ก าหนดชอเรยกของ line width แตละรปแบบ Gateway→Line Widths→Presentation tab, Width Names group
ก าหนดความหนา Gateway→Visualization→Line tab, Pixel Widths group
เชอมโยง legacy line width Gateway→Line Widths→Conversion tab, Legacy Width Conversion group
4
ก าหนดความหนา โดยใช user preference
Command Finder Visualization Preference
Location in dialog box Line tab, Pixel widths group
เชอมโยง legacy line width โดยใช user preference
Command Finder Object Preferences
Location in dialog box Line Widths tab, Legacy Width Conversion group
Zoom operation enhancements มการเปลยนแปลงคาเรมตนของทศทางการหมน mouse wheel ส าหรบ zoom in และ zoom out ใหม zoom in, หมน mouse wheel ออก หรอ สามารถกดป มซายและป มกลางของเมาสคาง หรอกดป ม Ctrl และป ม
กลางของเมาสคาง และเลอนเมาสออกจากตว zoom out, หมน mouse wheel เขา หรอ สามารถกดป มซายและป มกลางของเมาสคาง หรอกดป ม Ctrl และป ม
กลางของเมาสคาง และเลอนเมาสเขาหาตว
ถาตองการเปลยนคาเรมตน ใช Mouse Wheel Scrolling customer default
Tip : เลอก File tab→Utilities→Customer Defaults, และคลก Find Default .
Customize dialog box enhancements การปรบปรงทชวยใหเพมค าสงใน Ribbon bar ไดงายขน: ทกค าสงใน NX จะอยภายใต All Commands ใน Commands tab Ribbon bar drop-down list จะอยภายใต All Dropdowns
สามารถเปลยนขนาดของ icon ใน dialog boxes โดยไปท Icon/Tooltips tab เลอก Icon Sizes
Dialog Boxes = Normal
Dialog Boxes = Large (200%)
5
การใชงานทถกปรบปรง: มแทบ Tabs/Bars แทนทแทบ Ribbon และ QAT/Border Bars แทบ Layout และ Roles tabs ไมมแลว สามารถใชค าสงไดใน User Interface Preferences แทบ Options เปลยนเปน Icon/Tooltips. สามารถเรยกค าสงไดท
Command Finder Customize
Location in dialog box Customize dialog box→Commands tab→Search Customize dialog box→Icons/Tooltips tab→Dialog Boxes
Ribbon bar enhancements ปรบแตง Ribbon bar โดย right-click ท Ribbon bar แลวเลอก Customize ควบคมการแสดงผลของป มค าสงโดยคลกขวาแลวเลอกตวเลอกทตองการ กลบไปใชคาตงตน ใชตวเลอก Reset เรยกใช recently used command ไดใน Gallery
คลกขวาท gallery แลวเลอก Recently Used→Enable Recently Used.
สามารถยบ group หรอ gallery โดยคลกขวาทชอ group หรอ gallery เลอก Collapsed
สามารถพมแทบใหมโดยใชป ม คลกทป มแลวเพมชอในชอง Name ภายใน Tab Properties dialog box สามารถยาย Ribbon bar ไดโดยคลกขวาแลวเลอก Undock Ribbon ถาตองการซอนแทบ คลกขวา เลอก Hide Tab
6
Cue and Status line enhancements ควบคมการแสดงผลของ Cue line และ Status line เชน โดยคาตงตน Cue line และ Status line จะไมแสดงใน
Full Screen mode ถาตองการเปดใชงาน คลกขวาท Ribbon bar เลอก Cue/Status Line
User Interface Preferences enhancements
เขาถงทก interface preference ไดจาก User Interface Preferences dialog box ซงปรบปรงใหมโดยแบงตาม logical group
สามารถเรยกค าสงไดท
Application Gateway
Command Finder User Interface Preferences
View Section enhancements เมอสรางและแกไข section view สามารถก าหนดต าแหนงและขอบเขตของ section box โดยเลอกจาก object และ
ก าหนดคา margin
เลอกวตถโดยใช Select Object ใน Extent group หรอเลอกจาก Assembly Navigator
Tip : ถาตองเลอกวตถนอก section box ปด Clip Section
7
ก าหนดขอบเขตโดยระบคาในชอง Margin
Margin = 0
Margin = 3
สามารถก าหนดคาเรมตนส าหรบ Margin ได
Tip : หาคาเรมตนโดยเลอก File tab→Utilities→Customer Defaults, และคลก Find Default .
หยด dynamic update ของ section box โดยเลอก Delay Box Update และท าการอพเดตเมอตองการโดย
คลกท Update Box .
คณสมบตนท าใหสามารถเลอก section areaใน assembly ขนาดใหญไดรวดเรวโดยสราง section box คลมวตถทตองการ
สามารถเรยกค าสงไดท
Command Finder New Section , Edit Section
Location in dialog box View Section dialog box→Extent group
CSYS and View Triad enhancements ตอนนเราสามารถควบคมขนาดในการแสดงผลของ CSYS และ Datum CSYS และสามารถแสดง View Triad ใน
ต าแหนงมมลางขวาของ graphics window เคลยร Fixed Size on Screen check box เพอใหขนาดการแสดงผลของ CSYS และ Datum CSYS เวลา
zoom in หรอ zoom out อพเดตอตโนมต
8
Fixed Size on Screen Fixed Size on Screen
ถาตองการซอน CSYS และ Datum CSYS ส าหรบ solid และ non-transparent model เคลยร Show
Through check box.
Show Through
Show Through
ตองการแสดง View Triad ต าแหนงมมลางขวาของ graphics window ใช Bottom Right option
9
สามารถเรยกค าสงไดท
Application Gateway
Command Finder Visualization Preferences
Location in dialog box Visualization Preferences dialog box→View/Screen tab→Part Settings group
Rendering enhancements Scene Editor enhancements
ความสามารถใหม:
ใช non image-based advanced light effect เชน highlights และ shadows เพอ rendering ทสมจรง ดวยตวเลอกดงน
o ใช Advanced Studio Image-based Lighting
o ใช Ray Traced Image-based Lighting
ตวเลอก Generate High Quality Image Shadows ในแทบ Shadows ไมมแลว
จดทศทางของ environment image ดวย floor plane direction
o เลอก Up Vector = Align with Floor Plane
ใชคา stage setting รวมกนเชน size, offset และ floor plane ส าหรบ system scene ตางๆ NX จะคงตา stage setting เมอมการเปลยน system scene
System Scenes and System Materials enhancements
สามารถใช industry specific visualization system scenes และ system materials ทหลากหลาย โดย system scene จะจดอยภายใต category Indoor, Outdoor และ Studio
English และ Metric material จะไมมแลว
Studio Task enhancements
เขาถงค าสงทใชงานบอยดวย Studio Task shortcut menu
Select All Objects with this Material
Edit Material
Remove Material Assignment
Apply Selected Material
Inherit Material
10
สามารถเรยกค าสงไดท
Scene Editor
Command Finder Scene Editor
Location in dialog box
Lights tab→Use with Advanced Studio Image-based Lighting and Use with Ray Traced Image-based Lighting Global Illumination tab→Up Vector list→Align with Floor Plane
System Scenes and System Materials
Resource bar System Scenes tab, System Materials tab
Command Finder System Scenes , System Materials
Studio Task
Command Finder Studio Task
Graphics window Right-click the object→[command]
Roles enhancements
ไอคอนของ Roles เปลยนจาก เปน System Defaults category ปจจบนเรยกวา Content และมการแทนท Power Drafting
Essentials and Power Drafting Advanced role ดวย Layout role ซงมกลมค าสงทครอบคลม 2D conceptual design ใน Drafting application มากขน
มการเพม Presentation category เพอใหเลอก role ทเหมาะกบอปกรณทน าไปแสดงผล โดยไมมการเปลยนค าสงบน Ribbon bar มตวเลอกดงน :
Default Touch Panel Touch Tablet
ส าหรบขอมลเพมเตม ดท Touchscreen gestures for NX
สามารถเรยกค าสงไดท
Resource bar Roles tab
11
Touchscreen gestures for NX ใชค าสง Touch Mode เพอใชงาน NX บนอปกรณ touchscreen อยางมประสทธภาพ เลอก NX presentation
role ส าหรบแตละอปกรณ จาก Presentation category ใน Roles palette
Touch Panel
เพมประสทธภาพ NX interface presentation ทดทสดส าหรบจอ touch screen โดยrole น จะแสดง Ribbon bar แบบลอยตวทดานลางของอนเตอรเฟซและการเพมขนาดและพนทรอบองคประกอบอนเตอรเฟซเชน Ribbon bar tab, dialog box button และอน ๆ
Touch Tablet
เพมประสทธภาพ NX interface presentation ทดทสดส าหรบแทบเลต โดย role นจะแสดง Ribbon bar แบบไมม text เอา Border bar และ Title bar ออก และเพมขนาดและพนทรอบองคประกอบอนเตอรเฟซเชน Ribbon bar tab, dialog box button และอน ๆ
Default
เพมประสทธภาพ NX interface presentation ทดทสดส าหรบ non-touch monitor แสดงคาเรมตนของ NX interface
นอกเหนอจาก tap gesture ทวไปแลว ม press gestures ซงสามารถใชงานตางกน
Short press แตะแลวปลอยทจอในขณะกดป มคยบอรด
Long press แตะจอประมาณหนงวนาท
Action Gesture Description
Pan
ลาก object ดวยสองนว
Rotate
ลาก object ดวยหนงนว ถาตองการหมนรอบแกนใดแกนหนง ใหลากภายใน view border
Fit
แตะสองครงทใดกไดบนพนหลง
Zoom
แตะท object with ดวยสองนวแลวเคลอนนวทงสองเขาหากนส าหรบ zoom out และส าหรบ zoom in เคลอนนวทงสองออกหางกน
12
Orient the view
แตะดวยสามนวทใดกได
Rotate about a point
Short press ทต าแหนงจดหมน แลวเลอนนวในทศทางทตองการหมน object
Move an object or an on-screen handle
ลาก object ดวยหนงนว
View shortcut menu and shortcut toolbar
Long press และปลอยทใดกไดบนพนหลง
View object-specific shortcut menu and shortcut toolbar
Long press ท object แลวปลอย
Select the next option in a dialog box or complete an action
แตะดวยสองนวทใดกได
Select an object
แตะท object
Deselect an object
ใชหนงนวแตะคางทใดกได แลวแตะท object ทจะยกเลกการเลอก
Deselect all objects
แตะทพนหลง
Select multiple objects using the lasso or rectangular selection
Long press แลวลากใหเปนเสนลอม object ทงหมดทจะเลอก
Deselect multiple objects using the lasso or rectangular selection
แตะคางทใดกได แลวใชอกนวหนง long press กอน แลวลากใหเปนเสนลอม object ทงหมดทจะยกเลกการเลอก
13
View the QuickPick list for selection objects
Short press ท object ทตองการแลวปลอย
Select an item in the QuickPick list
แตะท item แลวแตะป ม OK หรอ ใชสองนวแตะทใดกได
View the QuickPick list for deselection objects
แตะคางดวยหนงนวแลว short press ท object ทตองการแลวปลอย
Browse to an item in the QuickPick list
แตะ item หรอทใดกไดเพอผานไป item ถดไป
Return to the previous item in the QuickPick list
ใชหนงนวแตะคางทใดกได แลวแตะดวยอกนวหนง
Input numeric values in the graphics window
ปอนคาโดยแตะทสญลกษณบน Numeric Keypad หรอ Full
Keyboard
Scroll ribbon tabs
ปด ribbon ในแนวระดบดวยหนงนว
Select a view command on a radial toolbar
แตะท Radial Spot แลวแตะค าสงทตองการ และยงสามารถปด Radial Spot ในทศทางของค าสงทตองการ
Select an object-specific command on a radial toolbar
แตะท Object-specific radial spot เพอแสดง radial toolbar ส าหรบค าสง object specific แลวแตะค าสงทตองการ
และยงสามารถปด Object-specific radial spot ในทศทางของค าสงทตองการ
Move the Radial Spot
แตะคางท Radial Spot จนกวาจะแสดงการเปลยนแปลง แลวลาก
สามารถเรยกค าสงไดท
Prerequisite Touchscreen
Command Finder Touch Mode
14
What’s new NX10
Sketching
15
Resize Chamfer Curve
เปนค าสงทใชส าหรบแกไขขนาดของ Chamfer ในหมวด Sketch ซงผใชงานสามารถปรบขนาดของ Chamfer ไดโดยการเลอนทลกศร (Drag Mouse) เพอปรบระยะ Offset Distance
และผใชงานยงสามารถใชงานค าสง Resize Chamfer Curve ในกรณท Sketch นนม Chamfer ทง 2 ดาน ทตองการใชปรบขนาดไปพรอมๆกน (symmetric) ไดอกดวย
ท าไมถงควรใชค าสงน ???
เมอใชค าสงนแลวจะท าให ผใชงานสามารถแกไข chamfers ใน Sketch ไดอยางสะดวก โดยไมตองค านงวา Sketch นนจะมการก าหนด constraints หรอไม
สามารถเขาถงค าสงไดอยางไร ???
Application จะสามารถใชงานไดเมออยในหมวดการท างานของ Sketch เทานน
Command Finder Resize Chamfer Curve
Menu & Toolbar Edit > Curve > Resize Chamfer Curve.
16
Curve Finder options. Curve Finder เปนตวชวยในการเลอกหรอคนหาเสน โดยจะอยในชดค าสงของ 2D Synchronous Technology ซงจะสามารถพบกบตวเลอกนไดใน 2 ค าสงคอ Move Curve และ Offset Move Curve
โดย Geometric Conditions ทมอยใน Curve Finder จะมดงตอไปน
Select Tangent
Select Parallel
Select Collinear
Select Concentric
Select Equal Radius
Select Symmetric
Select Offset
Select Coincident Vertex
Select Vertex on Curve
Select Chamfer
ท าไมถงควรใชค าสงน ???
ส าหรบผ ใชงานทมการแกไข Sketch ทมขนาดใหญหรอมรายละเอยดมาก จะชวยประหยดและเวลาในการเลอกเสนไดเปนอยางด
สามารถเขาถงค าสงไดอยางไร ???
Application จะสามารถใชงานไดเมออยในหมวดการท างานของ Sketch เทานน
โดยจะตดอยในค าสง Move Curve และ Offset Move Curve
Command Finder Move Curve หรอ Offset Move Curve
Menu & Toolbar Edit > Curve > Move Curve หรอ Offset Move Curve
17
2D Synchronous Technology settings
ในชดค าสง 2D Synchronous Modeling นน ในทกค าสงจะมสวนของ Setting อยบรเวณดานลางของ Dialog Boxes ซงใน Settings นไดมการเพมตวเลอก ดงรปดานลาง
NX9.0 NX10.0
ซงตวเลอกนจะเปนตวควบคม Angle of Adjacent sides และ Behavior of Arcs.
Size เปนการเลอกวาตองการทจะรกษาระยะและขนาดของเสนทท าการแกไขใหเลอกเปนแบบ Maintain แตถาเลอกเปนแบบTrim and extend กจะเปนการยดหรอตดเสนอนทเกยวของออกไปดวย ดงรปดานลาง
Size = Trim and Extend Size = Maintain
Keep Tangent เปนตวควบคมและรกษาสภาพการ Tangent ของเสนตรงกบสวนโคง
Keep Orthogonal เปนตวชวยในการรกษาสภาพของความเปนมมฉากเมอมการแกไขเสน โดยจะมผลท าใหเสนอนโดยรอบยงท ามมอยในลกษณะเดม
18
สามารถเขาถงค าสงไดอยางไร ???
Application
จะสามารถใชงานไดเมออยในหมวดการท างานของ Sketch เทานน
โดยจะตดอยในค าสง Move Curve , Offset Move Curve
และ Resize Curve
Command Finder Move Curve , Offset Move Curve , Resize Curve
Menu & Toolbar Edit > Curve > Move Curve หรอ Offset Move Curve
หรอ Resize Curve
Optimize 2D Curve เปนค าสงทใชส าหรบแกไขและปรบปรงเสน 2D ทผานการ Import เขามาในหมวด Sketch โดยผใชงานสามารถ
ทจะก าหนดคา Distance Threshold และ Angle Threshold เพอตงเงอนไขในการปรบปรงเสน ดงน การปรบปรงเสนและจดโดยการเอาออก
o แกไขโดยการน าเอาเสนทมการ overlap ออก o แกไขโดยการน าเอาเสนทมขนาดเลกๆ ตดๆ กนออก o แกไขโดยการน าเอาจดสวนเกนออก
การปรบปรงเสนโดยการเปลยนเสนแบบแทนทใหกบเสน splines , conic , Line และ Arcs o แทนทเสน splines หรอ conic ดวยเสนตรงและเสนโคงเมอมคา distance threshold ตรงตามเงอนไข o ปรบปรงเสน splines โดยการน าเอาคา C0 knot points และคา self-intersections ออก
ท าไมถงควรใชค าสงน ??? การ Import เสน 2D เขามาท างานใน Sketch นนอาจจะเกดการ Error ของเสนแบบตางไดงาย โดยค าสง Optimize 2D Curve นจะชวยในการแกไขเสนแบบตาง
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling
Command Finder Optimize 2D Curve
19
Creating sketch splines
NX10 ไดท าการเพมความสามารถในการสรางเสน Splines ในหมวด sketch เพอใหผใชงานสามารถสรางเสน Splines ไดงายและสะดวกขน
Studio Spline command เมอผใชงานท าการสรางหรอแกไขเสน Splines แบบ by poles กจะสามารถก าหนดคา Tangent Continuity แบบ G1 และ G2 ไดในขณะทเรมสรางจด start และ end poles. โดยการ drag Mouse.
Top Border bar มการเพม Snap Point แบบใหมคอ Poles ซงอยในสวนของ Top Border bar เพอใหสามารถเลอกจด Pole บนเสน Spline ได
Point construction มการเพม Option : Spline Pole ในการเลอกจดบนเสน Spline เขาไปในชดค าสงทมการเลอกแบบจด เชน ค าสง Line, Arcs
สามารถเขาถงค าสงไดอยางไร ???
Prerequisite สามารถใชงานไดในหมวด Sketch
Command Finder Studio Spline
Trimming sketch recipe curves
ผใชงานสามารถท าการใชค าสง Quick Trim, Make Corner, Fillet และ Chamfer กบเสนทไดมาจากค าสง recipe curves โดยไมตองท าการหยดการท าการของ associative
และในครงแรกทมการ Trimming เสนทไดจากการ recipe curve จะปรากฎค าเตอนวา the associativity will be removed. (ความสมพนธของเสนนจะถกน าออก)
สามารถเขาถงค าสงไดอยางไร ???
Prerequisite You must be working in an active sketch. The Home tab→Direct Sketch group→Create Inferred Constraints option must be turned on.
Command Finder
Quick Trim
Make Corner
Fillet
Chamfer
20
Creating WAVE links in a sketch ผใชงานสามารถท าการสรางความสมพนธใหกบชนงานทอยภายนอกการ Work part ไดโดยการใชค าสง
Constraint และ Dimension ทอยในหมวด Sketch โดยการสรางความสมพนธแบบน คลายกบการสราง WAVE Link ของการท าการ Assembly
ท าไมถงควรใชค าสงน ???
เพอใหผใชงานสามารถสรางความสมพนธไดงายและสะดวกมากยงขน และยงเปนรปแบบเดยวกบการสราง ความสมพนธแบบ Assembly อกดวย
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling
Prerequisite You must be working in an active sketch in an assembly.
Command Finder Rapid Dimension , Geometric Constraints
21
What’s new NX10
Modeling
22
Fill Surface enhancements
ค าสง Fill Surface มการเปลยนวธการทมอยในรายการของ Shape Control ดงน
NX9 NX10
1. เปลยนจาก Pass Through Curves ไปเปน Fit to Curves.
2. มการเพมค าสง Fit to Facet Body เขาไปใน shape control method เพอใชส าหรบการปดผว Facet
ท าไมถงควรใชค าสงน ???
เพอส าหรบปดผว Surface ทม gaps หรอร
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling : Insert > Surface > Fill Surface
Command Finder Fill Surface
23
Aero Design
Aero Design เปนกลมค าสงใหมทถกสรางขนมาเพอ รองรบการออกแบบยานพาหนะทกรปแบบ ซงชดค าสงน สามารถใชงานไดในทก Applications.
Aero Flange เปนค าสงทใชส าหรบสรางชนงานทมลกษณะของ flange body โดยการใชวธการ offset จากเสนขอบ
ไปถงผว Surface ของชนงาน ดงรปดานลาง
Open flange as part of web
Closed flange as part of access panel
Aero Rib เปนค าสงทชวยในการสราง Rib ใหกบชนงานในลกษณะแบบผนงบาง โดยการยดผวไปตามเสน Guide
Aero ribs as part of web
Closed aero rib as part of web
Aero Shelf เปนค าสงทใชส าหรบท าการ offset faces ไปตามขอบของชนงาน
Closed aero shelf
Aero shelf extension (two reference objects)
24
Aero Step เปนค าสงทชวยในการสรางชนงานตางระดบ โดยมวธการคอการ offset จากผวเดม ซงจะแบงการ Offset เปนแบบ region face
ในการสรางผวตางระดบ ผ ใชงานสามารถระบไดวาตองการอยางไร เชน length, depth, thickness และ offset.
Aero step middle offset
Aero step offset to plane
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling : Insert > Aero Design
Command Finder Aero Flange , Aero Rib , Aero Shelf , Aero Step
25
Face Blend enhancements
NX10 ไดมการปรบปรงค าสง Face Blend ใหสามารถใชงานไดอยางมประสทธภาพมากยงขน โดยการปรบปรงความสามารถในครงนนน จะน ามาแทนทค าสง Soft Blend ซงในรนตอๆ ไปนนจะไมม Soft-Blend
Multiple blend solutions เพม option ในสวนของ Cross Section ใหมมากขน เชน Rolling Ball, Naturally Varying, Circular และ Constant Radius blends
NX9 NX10
Blend Face continuity เพมความสามารถในการเชอมตอผว Surface ทง 2 ผว ทงแบบ tangent continuous และ curvature continuous
Blend constraint curves เพมความสามารถในการเลอกเสน Curve ส าหรบขอบของ Face-blend โดยสามารถเลอกไดทงแบบ Curve , แบบ Feature Edge ซงเปนรปแบบเดยวกบค าสง Soft-Blend
Face chains selected
Constraint curves selected
Face blend to constraint curves
New Trimming option เพมความสามารถในการ Trim คอ Trim to Short Input Faces โดยผใชงานสามารถเลอก เปด-ปด ได ดงรป
Trim Input Faces to Blend Faces
Trim Long Input Faces to Extended Rail Trim Input Faces to Blend Faces
Trim Long Input Faces to Extended Rail
26
Option name changes มการเปลยนชอเรยกในสวนของ Shape ทอยในกรปของ Cross Section ดงน
Tangent Symmetric เปน Symmetric Conic. Tangent Asymmetric เปน Asymmetric Conic.
Forced constant width method
เพมความสามารถในการสราง Face-Blends โดยสามารถปรบใหเปนแบบ Asymmetric ได เพอใหสามารถสรางแนว Face Blend ทแปลกออกไป และยงสามารถก าหนดรปรางของ Radius ไดมากขนอกดวย
Symmetric
Asymmetric Skew ratio determines asymmetric positioning
ท าไมถงควรใชค าสงน ???
สามารถสรางแนว Face-Blend ไดหลากหลายมากยงขน สามารถสรางแนว Face-Blend ไดกบผวทซบซอนไดงายยงขน สามารถใชการเลอกเสน constraint curves แบบ Soft-Blend ได สามารถเลอกการ Trim แบบ long face chain เพอยดผวของ Face-Blend สามารถเลอกปรบเปลยนไดทงแบบ symmetric หรอ asymmetric ในสวนของ constant-width blend.
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling
Command Finder Face Blend
27
Edge Blend enhancements เพมความสามารถของค าสง Edge Blend
Curvature continuity
ผใชงานสามารถเลอกเปลยนแนวรอยตอขอบของการท า Edge Blend ใหเปนแบบ curvature continuous หรอแบบ G2 ได เพอใหแนวของการท า Face Analysis นน ตอเนองและเปนระเบยบมากยงขน
Blend Face Continuity = Tangent Blend Face Continuity = Curvature
Segment blending ปรบปรงการสรางแนว Edge-Blend โดยการลดรอยตอของ segment ลง เพอใหแนวของ Edge-Blend นนสวยงามและเปนระเบยบมากขน ดงรปดานลาง
Segment Blend to Match Face Segments Segment Blend to Match Face Segments
สามารถเขาถงค าสงไดท ???
Application Modeling
Command Finder Edge Blend
28
Replace Face enhancement เพมความสามารถของค าสง Replace Face โดยสามารถใช Datum Plane ในการท า Replace Face ได ดงรป
สามารถเขาถงค าสงไดทไหน ???
Application Modeling
Command Finder Replace Face
Law Extension enhancements เพมความสามารถของค าสง Law Extension ซงท าใหค าสงสามารถยดผว Surface ได Smooth มากยงขน โดย
การใชวธ Angular Correction ในการสราง Surface
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Command Finder Law Extension
Location in dialog box Angle Law group→Angular Correction
29
Trim Sheet enhancements
NX10 ไดมการเปลยนชอของค าสง Trimmed Sheet ไปเปนค าสงชอ Trim Sheet โดยมการเพมความสามารถของค าสงดงน
มการเปลยนชอเรยกใน Cue line จากค าวา Target selection ไปเปนค าวา Select sheet bodies to trim.
มการเปลยนชอเรยกใน Cue line จากค าวา Region ไปเปนค าวา Select regions to keep or discard.
มการเปลยนชอเรยก Boundary Objects ไปเปนค าวา Boundary.
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Command Finder Trim Sheet
Synchronous Modeling Blend option NX10 ไดมการเพมตวเลอกในการลบผวของค าสง Delete Face ทอยในหมวดของ Synchronous Modeling
โดยไดมการเพมการลบผวแบบ Blend เขาไป ซงสามารถน าไปใชลบผวไดดงน สามารถลบ Blends ไดทงแบบ constant และแบบ variable radius สามารถลบ Notch blends
สามารถลบ Cliff blends
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling
Command Finder Delete Face
30
Trim and Extend ค าสง Trim and Extend ไดมการปรบเปลยน ดงน
การท างานแบบ By Distance และแบบ Percentage of Measured ไดถกเอาออก โดยใหไปใชในค าสง Extend Sheet แทน
NX9 NX10
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Prerequisite A sheet to trim and additional boundary geometry.
Command Finder Trim and Extend
Extend Sheet เปนค าสงทเพมขนมาใหมใน NX10 โดย มการท างานคลายกบค าสง Trim and Extend ทเปนแบบ By Distance
และแบบ Until Selected ดงรป
Extend using offset
Extend until selected
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Command Finder Extend Sheet
31
What’s new NX10
NX Realize Shape
32
Revolve Cage เปนค าสงใหมทอยในหมวดของ NX Realize Shape เปนค าสงทใชส าหรบการหมนรอบแกน โดยการเลอกเสน
Polylines หรอ ขอบของชนงาน cage
เสน Polyline ทใชในการท า Revolve Cage
การ Revolve รอบแกน Y เปนมม 360 องศา และม 8 segments
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Task environment NX Realize Shape
Command Finder Revolve Cage
Loft Cage เปนค าสงในการสราง Surface โดยอาศยการเลอกเสนทเรยงเปนแนวเดยวกน
การสรางแบบ 2 segment polylines และ 3 ขอบ
โดย Surface ทไดนนจะเปนแบบ 1 segment
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Task environment NX Realize Shape
Command Finder Loft Cage
33
Sweep Cage
เปนค าสงทใชในการท า Sweep Cage สามารถใชขอบของ Cage หรอ Polyline ในการเลอกเปน Section, Guide กได
เลอก 4 ขอบของ cage และ 2 guide polylines
Surface ทไดจากค าสง Swept cage
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Task environment NX Realize Shape
Command Finder Sweep Cage
Tube cage เปนค าสงในการค างานทอดวย Tube Cage โดยอาศยการเลอกเสน Polyline เปนเสน Guide และเลอกขอบของ
Cage เปนเสน Section
เลอกเสน Polyline 3 เสนเปน Guide
ผลทไดคอ Tube ทม 6 Segment
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Task environment NX Realize Shape
Command Finder Tube Cage
34
Extract Cage Polyline เปนค าสงทใชส าหรบการท า Extract เสน Curve ไปเปนเสน Polyline เพอน าไปใชงานกบค าสงอนๆ ในหมวด
Realize Shape เพราะค าสงในหมวดนไมสามารถน าเสน Curve หรอ Line ไปท างานได
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Task environment NX Realize Shape
Command Finder Extract Polyline
Copy Cage เปนค าสงทใชส าหรบการ Copy/Move ชนงาน Cage หรอเสน Polyline
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling and Shape Studio
Task environment NX Realize Shape
Command Finder Copy Cage
35
Sew Cage เปนค าสงทใชในการรวมผวของ Cage เขาดวยกน หรอท าการซอมชนงาน Cage ทมสวนทขาดหายหรอแหวงไป
โดยทผใชงานนนสามารถเลอกชนงาน 2 ชนงานทมปลายเปด หรอเลอกขอบของชนงานกได เพอใหท าการเชอมตอกน แตชนงานทง 2 ชนงาน ตองม number of edges ทเทากน
ส าหรบการเชอมตอชนงานทม gaps ผใชงานนนจะตองท าการเลอกไปทขอบของ cage
สามารถเขาถงค าสงไดอยางไร ???
Application Modeling
Task environment NX Realize Shape
Command Finder Sew Cage
36
What’s new NX10
Drafting
37
Restructure of the Drafting customer defaults
เปนการปรบปรงโครงสรางของการตงคา Customer default ใหม โดยมการจดเรยงไปในทศทางเดยวกนกบ Drafting Preference dialog box การจดโครงสรางแบบนจะเปนตวบงชโครงสรางของ customer default ทเรยกวา Subcategory ซงจะท าใหหนาตางของค าสงดกระชบกวาเดมแตสามารถเลอก option ในการใชงานงายขน
สามาถเขาถงค าสงไดอยางไร ???
Command Finder Customer Defaults
Menu File→Utilities→Customer Defaults
Borders and Zones enhancements
1 = Application
2 = Category
3 = Subcategory
38
เปนการปรบปรงค าสงการปรบตงคาในสวนของ Borders & Zones ทอยในการตงคา Drafting Preferences ซงไดน าเอารปแบบของการตงคาแบบเดยวกบ Customer Default มาใช ซงมผลท าใหผ ใชงานสามารถเขาถงการตงคาไดงายขน เขาใจงายขน
ส าหรบ Option ใหมของ preference and setting มดงตอไปน สามารถปรบแตงขนาดของหวลกศรไดละเอยดมากยงขน
สามารถเลอกการแสดงผลของสญลกษณ trimming marks ได 2 แบบ คอ triangle trimming mark และ corner trimming mark.
แสดงขนาดของ Size กระดาษ ไวทมมลางขวาของกรอบ
สามารถระบตวอกษรทอยนอกกรอบได
39
สามารถปรบตงคาของ margin โดยก าหนดจาก drawing border และ trimmed หรอ untrimmed drawing sheets.
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Command Finder Drafting Preferences
Location in dialog box
Drawing Format→Borders and Zones→Border Display node Drawing Format→Borders and Zones→Border Margin node Drawing Format→Borders and Zones→Zone node
Application Drafting
Command Finder Borders and Zones
Location in dialog box Settings group→Settings
Fit support for angled text in tables
NX10 Drafting ไดมการเพมเตมการปรบรปแบบการท า Text Fit ทอยในตาราง ดงน Wrap Auto Size Text Truncate Overwrite Border
Abbreviate Remove Spaces Auto Size Row Auto Size Column
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Prerequisite The Lettering Angle option in a cell must be set to something other than 0 degrees.
Location in dialog box
In the Drafting Preferences dialog box : Table→Common→Cell node→Fit Methods group In the Settings dialog box : Common→Cell node→Fit Methods group
40
Section View command ใน Version NX10 น ไดมการรวมเอาค าสง
Section ทงหมดมารวมไวใน ค าสงเดยวคอ Section
View
Section line
เปนค าสงใหมทตองใชคกบค าสง Section View โดยจะเปนค าสงส าหรบการสราง Section Line ทมลกษณะซบซอน หรอเอยงเปนมมไดงาย ซงผใชงานสามารถคลกเลอกจดทตองการใหเสน Section Line ผานไดเลย จากนนกเพยงแคเลอกค าสง Section View แบบ Select Exiting Line
Simple
Stepped
Simple/Stepped Half Revolved
Folded Unfolded Point to Point
41
Half
Point to point (folded and unfolded)
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Command Finder Section Line
Graphics window Right-click a drafting view→Add Section Line
View break enhancements View Break ใน NX10 ยงม Dialog Box แบบเดยวกบ NX9 เพยงแตใน NX10 นนจะมการเพมในสวนของ การ
รกษาสภาพของ Dimension ตางๆ ทมการบอกขนาดเอาไวกอนทจะมการท า View Break ซงถาเปน NX รนกอนหนาน ถาเสนของ View Break ผานบรเวณทมการบอกขนาดไวแลวนน กจะถกลบออก จากรปดานลางนน จะเหนวามการใสขนาดของ Radius และ Diameter เอาไวกอนทจะมการท า View Break
Pre-NX 10
NX 10
42
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Command Finder View Break
Graphics window Right-click a view border→Add View Break
Part Navigator Right-click a view node→Add View Break
Single-sided dimensions
เปนค าสงใหมทเพงมใน NX10 คอ เปนค าสงทใชส าหรบบอกขนาด โดยจะมเสนบอกขนาดและสวนชวยบอกขนาดเพยงดานเดยวเทานน แตเปนค าสงทไมไดม Icon แสดงบน toolbar ชดเจน ซงผใชงานจะตองท าการบอกขนาดดวย Dimension แบบปกตกอน จากนนจงเขาไปตงคาใน Setting ของ Dimension นนๆ และเลอกเปนแบบ Display as
Single Sided Dimension ซงจะตองใชคกบ Option ชอ Flip Dimension Side เพอสลบดานของลกศรของ Dimension
Example of a linear single–sided dimension
Example of an angular single–sided dimension
43
สามารถเขสถงค าสงไดอยางไร ???
Application Drafting and PMI
Graphics window
Right-click while creating a dimension→Settings
Double-click an existing dimension→Settings
Location in dialog box Single Sided node→Display as Single Sided Dimension
Linear dimension measurement types เปนค าสงในการบอกขนาด โดยทเปนตงเลอกส าหรบการใสคาพกดความเพอ คาบวก-คาลบ ซงโดยปกตจะเปนการ
บอกขนาดโดยทอยในบรรทดเดยวกนกบตวเลข Dimension แต Option นเปนการแสดงผลของคาบวกสงสดและคาลบต าสด โดยมลกษณะการแสดงผลทงหมด 3 แบบ คอ
General คอ การบอกขนาดแบบปกต และตามดวยพกดความเพอ คาบวก-ลบ
Directed คอ การบอกขนาดแบบแสดงผลคาบวกสงสด และคาลบต าสด แตจะวดจากจดใดจดหนงเทานน
Feature of Size คอ การบอกขนาดแบบแสดงผลคาบวกสงสด และคาลบต าสด แตจะวดจากจดกงกลางของขนาดนนๆ
44
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting, PMI
Prerequisite
The Enable Directed Dimensions option in the Drafting Preferences dialog box must be set.
Command Finder Linear
Location in dialog box References group→Measurement Type
Ordinate dimension enhancements
เปนการเพมความสามารถของค าสง Ordinate dimensions คอ
ผใขงานสามารถน าจด Origin เดมมาใชกบ View อนๆ ได โดยทยงคงมเสนบอกขนาดออกจาก Origin
ผใชงานสามารถใชค าสงใหมทชอ Clip Ordinate Dimension Line โดยเปนค าสงทชวยในการบอกขนาดในบรเวณทมขนาดเลก และไมสามารถวาง Dimension ลงไปไดหมด ค าสงนกจะท าการขยาย View บรเวณนออกมา และท าการบอกขนาดแบบ Ordinate Dimension โดยทยงคงอางองกบจด Origin เดม
45
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Command Finder Ordinate
Location in dialog box References group→List group
Automatic line breaks เปนค าสงทชวยใหผใชงานสามารถปรบแตง Dimension ทมการวางต าแหนงตดกบ Dimension อนๆ โดยค าสง
นจะท าการเวนชองวางตรงบรเวณทเกดการตดกนของเสนบอกขนาด
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Location in dialog box
In the Drafting Preferences dialog box: Common→Line/Arrow→Break node→Format group→Create Breaks and Break
Size In the Settings dialog box: Line/Arrow→Break node→Format group→Create Breaks and Break Size
Jogs on linear dimensions เปนค าสงส าหรบการบอกขนาด ในบรเวณทคบแคบ ซงจะเปนการท า Jog ใหส าหรบ Linear Dimension โดย
ผใชงานจะตองท าการบอกขนาดบอกปกตกอน จากนนจงเขาไปตงคาใน Setting > Jog จากนนกจะเลอกไดเลยวา ตองการเปด Jog ดานไหน ดานท 1 หรอดานท 2
46
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting and PMI
Location in dialog box
In the Drafting Preferences dialog box: Dimension→Jog node→Linear Format Side 1 group and Linear Format Side 2
group In the Settings dialog box: Jog node→Linear Format Side 1 group and Linear Format Side 2 group
Foreshortening symbols
เปนค าสงในการสรางสญลกษณ Foreshortening ใหกบ Dimension ทบอกขนาดใน Break View Add Foreshortening Symbol เปนการเพมสญลกษณ Foreshortening เขาไปในสวนของลกศร Remove เปนการเอาสญลกษณ Foreshortening ออกจาก Dimension Remove all Foreshortening Symbols เปนการเอาสญลกษณ Foreshortening ทงหมดออกจาก Dimension
47
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Graphics window
Double-click an existing dimension, or while creating a dimension, click the Edit on-screen button to enter the dimension edit mode, and then do one of the following:
Right-click the Extension Line, Arrow Line, or Leader Line access handle→Add
Foreshortening Symbol or Remove All Foreshortening Symbols Right-click the drag handle of an existing foreshortening symbol→Remove
Adding segments to a composite Feature Control Frame
เปนค าสงในการเพม Feature Control Frame เขาไปอกหลายบรรทด หรอหลายสวน โดยทยงคงอยใน Dimension เดยวกน
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting and PMI
Command Finder Feature Control Frame
Prerequisite In the Characteristics group, set the Frame Style option to Composite Frame.
Location in dialog box Characteristics group→Add New Frame
48
Balloon enhancement
เปนการเพมความสามารถในการใสลกศร ใหกบ Balloon โดยสามารถก าหนดใหโคนลกศรอยตรงบรเวณมมของ Balloon ได โดยรปรางของ Balloon ทสามารถท าไดคอ 3 เหลยม , 4 เหลยม และ 6 เหลยม
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Prerequisite The leader type for the balloon symbol must be set to Without Stub.
Location in dialog box
In the Drafting Preferences dialog box: Annotation→Balloon node→Format group→Create Leader Attachment to
Vertex In the Settings dialog box: Balloon node→Format group→Create Leader Attachment to Vertex
Inheriting PMI into a Drafting section view
เปนค าสงในการบอกขนาดในสวนของหมวด PMI และสามารถถายขนาดนนมายง Section View ได โดย Section View ทสามารถถายขนาดไดมดงน Simple , Stepped , Half , Pictorial , Half Pictorial
Balloon Type Available Vertices
Triangle Down, Triangle Up
Square, Divided Square
Hexagon, Divided Hexagon
49
สามารถเขาถงค าสงไดอยางไร ???
Application Drafting
Graphics window
Right-click the border of an existing Drafting section view→Settings →Common→PMI
50
What’s new NX10
51
Sheet Metal
Flange enhancement เปนการเพมความสามารถใหกบค าสง Flange โดยจะสามารถสราง Flange บนขอบของ contour flange และ Hem
flange ได โดยท Flange เหลานกยงคงสามารถคลออกไดแบบปกตอกดวย
สามารถเขาถงค าสงไดอยางไร ???
Application Sheet Metal
Command Finder Flange
Unbend and Rebend enhancements
เปนการเพมความสามารถใหกบค าสง Unbend และ Rebend โดยสามารถท า Unbend กบชนงานทมการพบเปนแนวโคงได ชนงานทม joggles ได แตผใชงานจะตองท า Convert to Sheet Metal เสยกอน
52
Advanced flange
Joggle
สามารถเขาถงค าสงไดอยางไร ???
Application Sheet Metal
Command Finder Unbend
Rebend
Convert to Sheet Metal enhancements เปนการเพมความสามารถของค าสง Convert to Sheet Metal โดยจาก Version กอนหนานเมอท าการ Convert
to sheet metal แลวจะไมสามารถมองเหนขอบของ การพบทเปนสวนโคง หรอขอบพบทเปน Step หรอ Joggle ได ท าใหไมสามารถคลชนงานในสวนนได
แตส าหรบ Version NX10 น เมอท าการ Convert to sheet metal แลว กสามารถใหค าสง Unbend และ Rebend ท าการคลชนงานตอไปเลย ตามทไดกลาวไวหวขอทผานมา
Original sheet metal part
Use the Convert to Sheet Metal command to convert the bend faces of the advanced flange and joggle to sheet metal.
53
After conversion, use the Unbend command to flatten the advanced flange and joggle.
สามารถเขาถงค าสงไดอยางไร ???
Application Sheet Metal
Command Finder Convert to Sheet Metal
Location in dialog box Additional Geometry group
Specifying a target body for creating normal cutouts โดยทวไป NX ใน Version กอนหนาน เมอผใชงานเลอกใชค าสง Normal cutout จะไมสามารถเลอกไดวาจะท า
การตดชนงานไหน โดยจะตองเขยนเสน Sketch ส าหรบตด Cutouts ลงบนผวของชนงานนนๆ แตส าหรบ NX10 นนสามารถเขยนเสน Sketch ลงบน Datum Plane ใดๆ กไดจากนนเมอผใชงานเลอกใชค าสง
Normal cutout ตวค าสงกจะมการถามวา ตองการทจะตดลงไปบนชนงานไหน
Original sheet metal part
Specify the normal cutout section.
For this example, Limits = Through All.
Select the target body.
54
NX creates the cutout on the specified target body.
Where do I find it?
Application Sheet Metal and Flexible Printed Circuit Design
Command Finder Normal Cutout
Location in dialog box Target group→Select Body option
Specifying a target face for creating bends and jogs โดยทวไป NX ใน Version กอนหนาน เมอผใชงานเลอกใชค าสง bends หรอ jogs จะไมสามารถเลอกไดวาจะ
ท าการพบชนงานไหน โดยจะตองเขยนเสน Sketch ส าหรบพบ bends หรอ jogs ลงบนผวของชนงานนนๆ แตส าหรบ NX10 นนสามารถเขยนเสน Sketch ลงบน Datum Plane ใดๆ กไดจากนนเมอผใชงานเลอกใชค าสง
bends หรอ jogs ตวค าสงกจะมการถามวา ตองการทจะพบลงไปบนชนงานไหน
Original sheet metal part
Specify the bend line.
The bend line must lie on a plane that is parallel to the target face.
Select the target face.
55
NX creates the bend on the body of the specified target face.
สามารถเขาถงค าสงไดอยางไร ???
Application Sheet Metal and Flexible Printed Circuit Design
Command Finder Bend Jog
Location in dialog box Target group→Select Face option
Gusset enhancements
เปนการเพมความสามารถใหกบค าสง gussets โดยสามารถใช Datum Plane มาระบต าแหนงของ Gusset โดยท datum plane นนจะตองท ามมตงฉากกบแกนของ bend. และยะงสามารถท าการคลออกไดดวยค าสง Flat Pattern อกดวย
Square gusset
Round gusset
Example In the example, the flange is unbent to create a normal cutout and then rebend. Notice that NX removes the gusset feature after the unbend operation.
56
To retain the gusset after the unbend operation, in the Part Navigator, reorder the Gusset feature after the Rebend feature to re-create the gusset.
Model History
Datum Coordinate System (0)
SB Tab (1)
SB Flange (2)
SB Unbend (3)
Datum Plane (4)
SB Normal Cutout (5)
SB Rebend (6)
SB Gusset (7)
Flattening bends with gusset features
เมอผใชงานท าการคลชนงานดวยค าสง Unbend นน กจะปรากฎเสนแนวของ Gusset บนแผนคล แตถา
ผใชงานไมตองการใหปรากฎเสนแนวน กสามารถเลอกยกเลกไดจาก Check box ทชอ Extract Gusset Curves ซงจะอยภายในค าสง Unbend
สามารถเขาถงค าสงไดอยางไร ???
Application Sheet Metal
Command Finder Gusset Unbend
57
Location in dialog box
Gusset dialog box→Location group→Specify Plane options
Unbend dialog box→Additional Curves or Points group→Extract Gusset Curves check box
What’s new NX10
CAM
58
General enhancements Creating the IPW in the background
สามารถสราง in-process workpiece (IPW) ส าหรบ operations งาน drilling หรอ milling ในขณะทใชงาน operation อนอย ดวยการใชค าสง Parallel Create 3D IPW ซงการท างานจะคลายกบการใชงานค าสง Parallel
Generate โดยการสราง IPW ดวยค าสงน จะเปนประโยชนอยางมากในการใชงานเมอ
เมอคณไมตองการรอ การสราง IPWs ของ operation กอนหนาทคณจะท าการ simulate หรอ generate ใน operation ถดลงมา
คณจะสามารถใชออปชน Show Thickness by Color เพอตรวจสอบ IPWs ของชด operations นนๆไดทนท
ในขณะก าลงสราง IPW ทงใน operation เดยว หรอหลาย operation
จะปรากฏสญญาลกษณ หนา operation ทก าลงสราง IPWs ใน Operation Navigator
สามารถยตค าสงในขณะก าลงท าการสราง IPW ดวยการคลกขวา แลวเลอก Stop Parallel Create 3D
หลงจากท าการสราง IPW ใน column ของ IPW ใน Operation Navigator จะแสดงสถานะของ operation ดงน
Generated Not generated Out of date สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite Generate the operations before you attempt to create an IPW and then select them.
59
Ribbon bar Home tab→Workpiece group→Parallel Create 3D
Operation Navigator Right-click one or more selected operations→Workpiece→Parallel Create 3D IPW
Verification settings and playback enhancements Keyboard shortcuts
สามารถใชป ม Playback ในการควบคมขณะท าการ Verify ไดดงน
Step Right arrow key
Step Backward Left arrow key
Forward to Next Operation Page Up key
Rewind to Previous Operation Page Down key
หากตองการใหเคลอนทตอเนอง สามารถกดป มคางไวได
Note สามารถใช arrow keys ในการเลอนแถบบน selected list ได
Tool Path Visualization settings
ในขณะนการตงคาใน Tool Path Visualization dialog box ขณะ verify จะถกเกบไวตลอด ยกเวนแตการเลอนคาบน list ขอมลดานบน ทจะไมเกบไว
Note NX จะไมเกบการตงคาใน dialog boxes เมอมการเปดโปรแกรมขนใหม
Tool path display during playback
ในออปชนการแสดง Tool Path จะมออปชนเพมขนคอ Start to Current Motion เพอใชแสดง Tool Path ตงแตจดเรมตน จนถงจดท Tool ก าลงท างานอย
60
Start to Current Motion
All
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite
ตองม operation ท generate เรยบรอยแลว จงจะสามารถ เลอก
arrow key ส าหรบก าหนดการเคลอนทในต าแหนงตางๆ
ตงคาทจ าเปน เพองายตอการเปด Tool Path Verification dialog box มาใชงานในครงถดไป
Location in dialog box Replay or 3D Dynamic tab→Tool Path list→Start to Current Motion
Displaying cutter paths ส าหรบ operation ของงาน milling และ drilling สามารถใชค าสงในการแสดง tool path ในแถบ Home เพอกรองการแสดง tool path ทเลอกใน Operation Navigator
Show Cutting Moves
Show Non Cutting Moves
Show Tool Center This option affects ball tipped cutters only.
End Point
61
Note o ไมจ าเปนตองตงคา environment variable เปน UGII_CAM_TP_DISP_ENDPOINTS เพอแสดง end points
o ถาท าการปดทงหมด Show Cutting Moves และ Show Non Cutting Moves, NX จะปดการแสดงผล เมอเลอก operation ใน Operation Navigator
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite เลอก operation ทตองการใน Operation Navigator
Ribbon bar Home tab→Display group
Displaying cutter paths Display group
ใชสองออปชนใหมนในการแสดงผล ซงสามารถเลอกไดในแถบของ Home ส าหรบการจดการการแสดงผล เมอท าการเลอก หรอแกไข operation
Display Drop-down
ใชออปชน Display Tool Path เพอแสดง tool path อยางรวดเรว ซงออปชนนรองรบการแสดงผลของ display group ดานบน (show cutting move, show non cutting move)
ใชออปชน Replay Tool Path เพอแสดง tool path ทงหมดทตงไว ใน Display Options ซงรวมถง tool และการแสดง tool path, feed rates, arrows, line numbers และออปชน generation คณสามารถเปดใชงาน Display
Options จาก Options group เมอจะท าการสราง หรอแกไข operation
Coloring Drop-down
62
คณสามารถตงคาการเปลยนสของการเคลอนทกดงาน ตาม operation หรอ tool
ภาพทแสดงอยนเปดจากชนงาน sim06_mill_5ax_cam... จากโฟลเดอรของ \MACH\samples\nc_simulation_samples ชงจะท าการเลอกสาม operation ในแตละภาพ
ROUGHING
FACE_TOP
CAVITY_TOP
CAVITY_MILL
Motion Type
สามารถใชออปชน Motion type เพอแสดงลกษณะการกดรปแบบนไดตงแต NX 9.0.2.
การเคลอนทของ Tool path จะแสดงเปนส ซงสามารถตงการการแสดงสไดท Options→Edit Display→Path
Display Colors และคณสามารถทจะเปลยนสใหแตกตางกนไดเชนสของ engage, retract, rapid, and cutting moves.
จากภาพตวอยางเปนการแสดงสทโปรแกรมตงมาให
Tool
63
ใชออปชน Tool ในการแสดง non-rapid moves ของ tool paths ดวยสทแตกตางกนในแตละ tool
จากตวอยางเปนการแสดง tool path ตามสของ tool สอง tool path แรกใช tool เดยวกน จะแสดงเปนสน าเงน สวนโปรแกรมทสามมการเปลยน tool สทแสดงจะเปนสเขยว
Operation
ใชออปชน Operation ในการแสดง non-rapid moves ของ tool paths ดวยสทแตกตางกนในแตละ operation
ในตวอยางส tool path ของ FACE_TOP operation จะเปนสน าเงน ส tool path ของ CAVITY_TOP operation จะเปนสเขยว และส tool path ของ CAVITY_MILL operation จะเปนสเหลอง
Customer defaults for tool and operation colors
สของการใชงาน by Tool หรอ Operation จะถกรยกเขามาใชงานตามคาของการเลอกแสดงในรปแบบของ by tool และ by operation
ส และ Font ของ Rapid Motion จะเปนสแดง และเปนเสนปะ
64
Tip สามารถเขาไปปรบตงคา customer default ไดดวยการเลอก File tab→Utilities→Customer Defaults - Manufacturing – User Interface – Tool Path Display
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite เลอก operations ใน Operation Navigator หรอท าเลอก edit operation.
Ribbon bar Home tab→Display group
Connecting tool path segments after edits ใชออปชนใน Transfer/Rapid group ของการ Trim Tool Path ตอ tool path ทถกตดออก ในระหวางการใชงาน Tool Path Editor
Transfer at Direct ใช direct เชอมตอปลายทถกตดไปยงจดทตองการเขางาน ใน
การเรมเขางานครงถดไป
Clearance ตงคาความสงของ clearance ส าหรบการเคลอนทยายต าแหนง
Lowest Safe Z ใชงานในลกษณะของ direct กอน แตถาหากวาตรวจพบวายกไมพนชนงาน กจะปรบไปใชในลกษณะ previous safe Z-level plane
Smooth สรางคาการยายต าแหนงตามคา default ซงจะยงไมสามารถปรบแตง
65
Smooth connections
Plane ชวยใหคณสามารถก าหนด plane ในการเคลอนทยายต าแหนง ระหวางทคณใชการ Trim
Transfer using None ไมมการระบการเคลอนยายต าแหนง
Ramp on Shape
สรางลกษณะการเขางาน ตามรปรางของชนงาน ในการเขางานครงแรก
Lift and Plunge
ปรบแนวการเขา และออกตามแนวตง และใสคาความสงของ Lift and Plunge
Height ตงคาความสงส าหรบการยก เพอเคลอนทไปต าแหนงถดไป
สามารถเรยกค าสงไดท
Application Manufacturing
Command Finder Edit tool path
Operation Navigator Right-click operation→Tool Path→Edit
Location in dialog box
[Tool Path Editor] dialog box→Edit Actions group→Trim →[Trim Tool Paths] dialog box→Transfer/Rapid group
66
Trimming tool paths in the Tool Path Editor คณสามารถตด tool path โดยการเลอกพนทบนหนาจอใชงาน ตามแนวระนาบ ดวยเครงมอในการชวยเลอกดงน
Rectangle
Lasso
Polygon
Tip สามารถเพมรปแบบการเลอก Select by Polygon โดยใช Command Finder คนหา Select by Polygon คลกขวาแลวเลอก Add to Top Border Bar และท าการเลอก customize เพอลาก Select by Polygon ไปวางยงต าแหนงทตองการ หรอวางใน Selection list.
คณสามารถระบรปแบบการเชอมตอของการเคลอนทในรปแบบ smooth จากในรป tool path ทเหน ผนงดานท (1) และ (2) มการชนกบ tool holder ซงคณสามารถทจะท าการ trim พนทจอง tool path บรเวณนออกไปได
คณสามารถเลอก trim พนทดานในดวยการเลอกกรอบสเหลยมดงรป
เมอสวนแรกแกไขเรยบรอย เลอก trim อกครง เพอเลอก trim ดานในกรอบสเหลยมสวนทสอง
67
คณสามารถท าทงสองดานในครงเดยว ดวยการเลอก trim outside แลวเปลยนรปแบบการเลอกเปน Lasso (shown) หรอ Polygon
Smooth connections between trimmed motions
จากรปเปนการแสดงการ trim path ดวยการใชออปชน smooth connections
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite ตองแกไข tool path ทท าการ generated แลว
Command Finder Edit Tool Path
68
Operation Navigator [Select operation]→right-click→Tool Path→Edit
Location in dialog box
Edit Actions→Trim →Trim Tool Paths dialog box→Trim Geometry group→Geometry = Selection in View
เลอกลกษณะการเลอก trim บนแถบ Top Border bar
Milling Cut regions and cut order in Flowcut Single operations Cut Regions dialog box จะปรารฎขนเมอใชค าสง Flowcut ซง Segments จากใน version กอน จะมาอางองในรปแบบของ region แทน
ใชงาน Flowcut Single operation เลอก Cut Regions dialog box เพอ reorder, divide, หรอ delete regions ของ flowcut path
Regions to Cut group
Name column
แสดง cut regions ต าแหนงของ cut order เพอท าการยายต าแหนง ดวยการลากไปวางในต าแหนงทตอการ และยงสามารถเปลยนชอ cut region ใน column ไดตามตองการ
Divide
ชวยในการก าหนดจดเพอแบง cut region ทเลอกไว ซง NX จะใชจดทใกลทสดใน region ในการคลกมาวางเปนจดแบง และจะเกดตวเลขของจดขน เมอน า mouse cursor ไปวางบรเวณจด เพอใหงายตอการตดสนใจ
Reverse
กลบทศทางการกดของ region ซง NX จะแสดงทศทางดวยลกศร จากจดเรมตนของ region
69
Delete
ลบ region ออกจาก tool path
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite สราง หรอแกไข Flowcut Single operation และ generate operation
Cut region control for Flowcut Reference Tool
คณสามารถแบง cut area ใน Flowcut Reference Tool operation เพอใหสามารถตงคา Cut Order list ไดตามความตองการของ User และใน Flow Cut Drive Method dialog box คณยงสามารถปรบคาองศาความชนของผวเพอแบง cut region ไดอกดวย
Region sizes
คณสามารถควบคมขนาดของ region ดวยการ Merge หรอ divide ไดตามตองการ ซง NX จะท าการ update ทนททมการแกไข
ตวอยางการ merged regions
70
Region 11 Region 12 Regions merged as one
ชอเมอมการสราง region
<operation_name> _R_1
<operation_name> _R_2
เมอท าการ divide regions ตวเลขของ region ทถกแบงออกมาจะเรยงกนล าดบ อยางเชน ถาคณ divide Operation_R_1 ผลทไดกจะเปนตามน
Operation_R_1_1
Operation_R_1_2
Cut regions and cutting sequence
คณสามารถควบคม region ดวยการเลอกกดตามล าดบทตองการ ลบบรเวณทไมตองการ เพอขามพนทไมตองการกดนนไป
ตวอยางขอมล Cut Regions
Name Cut Order Containment Type
Operation Regions
FLOWCUT_REF_TOOL_R_1 1
Flow
FLOWCUT_REF_TOOL_R_1 2
Flow
FLOWCUT_REF_TOOL_R_1 3
Flow
FLOWCUT_REF_TOOL_R_1 4
Flow
FLOWCUT_REF_TOOL_R_1 5
Flow
FLOWCUT_REF_TOOL_R_1 6
Flow
FLOWCUT_REF_TOOL_R_1 7
Flow
FLOWCUT_REF_TOOL_R_1 8
Flow
FLOWCUT_REF_TOOL_R_1 9
Flow
Cut order labels ใน graphics display ใชเทยบกบ Cut Regions list
71
คณสามารถท างานดงตอไปนไดอกดวย
ควบคม cut pattern และปรบ tool path parameter ภายในแตละ cut region ก าหนดรปแบบ region เปน steep หรอ non-steep Control the cut pattern and other tool path parameters within each cut region. Define a region as steep or non-steep และ NX จะประยกตใช Flowcut Drive Method ทตงคาไวอยางเหมาะสม
ปรบรปแบบ containment ส าหรบ region.
ปรบเปลยนทศทางการท างานของ flowcut region cut direction
Editing updates
คณสามารถท างานดงตอไปนได
Drag regions เพอเปลยนต าแหนงใน cut order.
Undo เพอเปลยนคาทแกไขกลบคนมา
ท าการบนทกคาล าดบการกด ซงจะใชกบการ generate และบนทกเมอมการปรบปรง tool path
ท าไมถงควรใช
เพอใหสามารถจดการ region ในแตละพนทการกดไดอยางมประสทธภาพ ปรบปรงผวงานละเอยดใหดยงขน ลดการสกหรอ และเพมประสทธภาพของเครองมอตด
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite A Flowcut Reference Tool operation
Location in dialog box
Flowcut Ref Tool dialog box→Drive Method group→Method row→Edit
Flow Cut Drive Method dialog box→Output group→Cut Order→User
72
defined→OK
Flowcut Ref Tool dialog box→Actions group→Generate →Cut Regions dialog box
Corner smoothing
คณสามารถใช smooth corners ใน Zlevel cut patterns ของ Flowcut Reference Tool operations เมอใชงานคณสามารถทจะ
ตงคา steep และ non-steep regions ส าหรบ Zlevel
เลอก Corner Smoothing ใน cutting parameter
ก าหนดขนาด Radius เพอใชกบ corners
Previous versions of NX NX 10.0
ท าไมถงควรใช
เมอคณกดงานทมความแขง หรอกดงาน high speeds ควรเลอกเปนการท างานในลกษณะโคงของทกมม ซง corner fillets สามารถท าประโยชนไดดงน
ปองกนการเปลยนทศทางอยางฉบพลน และอาจมผลกระทบกบ cutter ซงอาจเกดความเครยดมากเกนไปบนเครองมอ และเครองมอตด
ชวยในการสราง tool part ส าหรบสงออกเปนแบบ Nurbs เพราะรปแบบการเดนแบบ smooth งายตอการออกเปน Nurbs มากกวาเปนมม
ออปชน Corner Smoothing ชวยใหคณควบคม tool path ส าหรบงานละเอยดไดดยงขน และเพมประสทธภาพในการ machine
สามารถเรยกค าสงไดท
73
Application Manufacturing
Location in dialog box
[Flowcut Reference Tool operation]→Cutting Parameters→Corners tab→Path Shape
in Corners group→Smoothing row→All Passes
Automatic cut pattern direction
คณสามารถเลอกใชออปชน Automatic ในสวนของ pattern direction เมอเลอก cut pattern เปนแบบ Follow Periphery ซง pattern direction จะเลอกระหวาง Inward และ Outward ใหกบ cut level และ cut region ตามเงอนไขดงตอไปน
ส าหรบงานทเปนแบบเปดดงรป tool จะเขางานดานนอก และท างานเขาไปหาจดศนยกลาง
ส าหรบงานทมกรอบดานนอก หรอเปนชนงานปด tool จะลงจากดานนอก และท า slot ไปยงจดเรมตน และกดงานออกดานนอก หรอ engage ลงดานในหากเปนชนงานปด แลวกดออกหาผนง
ส าหรบรปแบบการกดในลกษณะ Outward กบงานในลกษณะ bosses จดเขา และแนวการเขาสามารถเปลยนแปลงได
Previous NX results NX 10.0 results
74
1 = Entry point
2 = Region start point
Pockets, ชองวาง หรอหลม จะคดเปนเนอเปดในการ engage ใหอตโนมต
Previous NX results NX 10.0 results
ท าไมถงควรใช
การใช pattern direction แบบ Automatic จะชวยปรบลกษณะการท างานของ tool path ใหทรงประสทธภาพมากขน และไดอายการใชงานของ tool ทยาวนานขน
สามารถเรยกค าสงไดท
Application Manufacturing
Location in dialog box
Cutting Parameters dialog box→Strategy tab→Cutting group→Pattern
Direction→Automatic
Using a boundary with the Area Milling drive method
75
Specify Trim Boundaries
ใชค าสง Specify Trim Boundaries ควบคมบรเวณทตองการกดงาน contour ใน Area Milling
รองรบพนทการกดไดทง พนทเดยว หรอมากกวา ส าหรบการเลอกขอบเขต bounding objects ซงสามารถเลอกขอบเขตเปนขอบ, curves หรอจด และขอบเขตจะ project ลงบนชนงานตามแนวแกนของ boundary plane
Edge as boundary
Cut Region Boundary edge, trim inside Tool Path
Sketch as boundary
76
Sketch as boundary
Boundary sketch, trim outside Tool Path
Closing gaps
คณสามารถปลอยระยะหางระหวางเสน หรอขอบของงาน ซงระยะหางดงกลาวจะปดใหอตโนมต
ลกศรแสดงการปดระยะหาง ในการใช trim boundary outside
Tool Path
Nested boundaries, no overlap
สามารถก าหนดขอบเขตของ boundaries ซอนกนดงภาพ
Outer boundary trim outside
Inner boundary, trim inside
Tool Path
77
Linear open boundary
คณสามารถก าหนด boundaries แบบเปดได
Mouse clicks at (1) and (2) define two points, off part, as an open boundary
Tool Path
Trim boundary options
ออปชน trim boundary สามารถใชงานใน Contour Area จะปรากฏออปชนเมอเปลยนรปแบบการกดเปนแบบ . Area Milling
Fixed Contour
Contour Surface Area
Contact tool position
เมอคณก าหนด tool position เปนแบบ Contact, NX จะท าการเคลอนทจด contact ของ tool ไปยงแนว project กบขอบเขตของผว ทท ากบ boundary แทนการวางโดยใช center ของ tool
Area milling geometry with boundaries
ใน Geometry ของ Operation Navigator คณสามารถสราง MILL_AREA geometry group และสราง trim boundaries ไวภายใน เมอเราตองการแกไข trim boundaries เพอเปลยน geometry area จะแกไข operations เปนแบบ multiple ได
NX จะแสดง Geometry list เมอเลอกเปนแบบ Contour Area operation subtype เทานน ถาคณสรางจาก Fixed
Contour หรอ Contour Surface Area คณตองแกไข drive method เปน Area Milling กอน จงจะปรากฏ Geometry list ในสวนของ Trim boundary
78
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite คณตองม operation งาน contour ทใช drive method ในรปแบบ Area Milling
Location in dialog box Geometry group→Specify Trim Boundaries
Contact tool position on Area Milling boundaries เมอคณก าหนด Contact tool position, NX จะวาง tool ตามรปแบบการเลอกของพนททตองการกด
ชนงานตวอยางนมทงผวเวา และนนอยในขอบเขตของเสน sketch สเหลยม
เมอ project ตามแนวแกน Z ตามตวอยาง ขอบเขตจะอยบนผวทงทเปนสวนเวา และสวนโคง
79
จะเหนไดวาแนว tool เมอมองตามแนวแกน Z จะวางอยบนขอบเขตพอด
เมอใช tool position แบบ On บนพนผวทมความชน บางผวทมความโคงเวา อาจเกบไมหมด และสวนทโคงนน อาจถกเกบออกนอกขอบเขตทตองการ ทเปนเชนนเพราะจดในการ contact ของ tool อาจตองการระยะออกจาก boundary
80
จะเหนไดวา เมอใชแนวแกน too เหมอนเดม กบการเปลยน tool position เปนแบบ Contact ต าแหนงของ tool จะสามารถเคลอนทเกนออกไปได หรอหยดกอนถงขอบเขต ซงขนอยกบความลาดเอยงของผว
ออปชน Contact positions จะเปนการใชจด contact ของ tool ทสมผสกบผวเปนขอบเขต ซงจะมนใจไดวาจดทสมผสอยในขอบเขตของ boundary ไมออกไปนอกขอบเขต หรอไปไมถง
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite
สราง หรอแกไข operation ทใช drive method แบบ Area Milling และสราง boundary หรอแกไข boundary เพอบอกขอบเขตการเคลอนทของ tool
Operation dialog box Specify Trim Boundaries
Location in dialog box Trim Boundaries dialog box→Boundaries group→Tool Position list→Contact
81
Swarf Blade tool axis enhancement Swarf Blade tool axis enhancement
ส าหรบ operation งานเกบละเอยด blade ไดปรบออปชน Swarf Blade ใหดยงขน ดวยการปรบแนวแกนใหเหมาะสมกบผวงาน
Previous versions
Current version
ถาคมตดของ tool มความมากพอ การ swarf กจะสามารถกดเกบละเอยดไดภายในการกนเพยงครงเดยว ซง NX จะใชแนวการกดในเหมอนกนถงแมวาจะเปนการกดหลายๆชนลงไป
สามารถใชออปชน Tilt Clearance Angle เพอก าหนดองศาการ lead เมอเรมตนเขาท างาน และจบการท างาน แตสามารถปรบเปนคาบวกไดเทานน
Tilt Clearance Angle = 20
Tilt Clearance Angle = 0
Note เราขอแนะน าออปชน Swarf Blade กบ ruled surfaces แตจะไมเหมาะสมกบงานในลกษณะ complex curvatures
82
Ruled surface กบแนวทสมบรณแบบ
Complex curvature มความเสยงทจะมเนอเหลอ หรอเขาเนองาน
สามารถเรยกค าสงไดท
Application Manufacturing
Command Finder Create Operation
Location in dialog box
Create Operation dialog box→Type list→mill_multi_blade→Operation Subtype
group→Blade Finish
Improving surface finish on corners and filletsCurve/Point drive method เมอคณใชการท างานในลกษณะ Curve/Point คณสามารถทจะ
วางต าแหนงของ tool เคลอนทไปตามเสนขอบของ geometry ทระบคา offset ดวยการใชออปชน Offset Left
ปรบต าแหนง contact point ในระยะแนว tangent ของจดทไมใช center ของ tool เชนการใช bull nose หรอ end mill เมอคณท าการกดไปรอบๆ แนวแกน แนวทปรบจะเทากนรอบแนวแกน
Chamfer.
การปรบปรงนมวตถประสงคเพอใหไดผวงานกด 5 แกน ของงาน rotary floors ทดขน ซงการใชงาน Curve/Point ไมไดมเฉพาะการใชงานกบ rotary floors เทานน การเปลยนแปลงยงสามารถใชงานในหมวดของการท างานอนไดอกดวย เมอแนวแกนไมไดตงฉากกบผวงาน คณจะเหนความแตกตางนเชนกนในงาน 3 แกน จะปรากฏออปชน Offset Left เชนกน
Following edges at an offset
NX ท าการสราง tool path ตามลกษณะของ
1. Offsets จากการเลอกขอบ หรอเสน ตามแนว cut area surface เพอสราง drive curves
83
2. Checks gouges กบ part หรอ geometry และลบสวนทพบใน gouge ถาคา offset นอยเกนไปกจะไมท าการสราง tool path
Note การระบคา offset ไปดานขวา ใหใสคาเปนลบ
ในตวอยาง drive curves เปนการเลอกจากขอบของชนงาน
Part to machine
Cut area and edges to offset
Tool diameter = 3 mm
Offset Left = 1.5 mm
Drive curves
Tool path
Shifting the contact
ตวอยางนแสดงผลเมอมการใสคา shift ของ tool contact ดวยคา 1.5 mm บน tool ขนาดเสนผานศนยกลาง 3 mm
Tool at default contact point Tool contact shifted
84
Chamfering with Curve/Point
ใช chamfer tool และก าหนดคา stock เปนลบ เพอกด chamfer เมอท าการ generate จะม warning message เตอน เพอทจะด าเนนการ generate ตอ ใหท าการคลก No ใน message box
ท าไมถงควรใช
การปรบปรงชวยเพมคณภาพของผวงาน ซงกอนหนานไมสามารถทจะ shift tool contact และไมสามารถ offset curve ชวยใหคณไมจ าเปนทจะตองสราง offset curve เพอมาเปน drive curve
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite Curve/Point drive method
Location in dialog box
Curve/Point Drive Method dialog box→Drive Settings group→Offset Left and Tool Contact Shift
85
Performance enhancements for Floor Wall operations using a 3D IPW
เวลาทตองการ generate หรอ operation กบออปชนการ Preview ทมการปรบปรงใหดยงขน ประสทธภาพของ blank และ 3D IPW กจะทรงประสทธภาพมากขนดวย จะเหนไดชดกบงานทมความซบซอนสง
สามารถเรยกค าสงไดท
Application Manufacturing
Command Finder Floor and Wall with IPW
Hole machining Boss milling and threading operations
ม operations ส าหรบงาน mill และงาน thread boss คณจะสามารถเลอกไดเฉพาะ boss จากภายใน operation น เทานน
Boss Milling Boss Thread Milling
ตามรปแบบ operation น สามารถ machine ไดเฉพาะรเทานน
86
Hole Milling
Thread Milling
ป มเลอก Specify Hole or Boss ปจจบนเปลยนชอเปน Specify Feature Geometry ภายในแตละ operation คณจะสามารถเลอก หรอแกไขไดเฉพาะคาทเหมาะสมกบ เทานน feature geometry
ท าไมถงควรใช
รปแบบของ operation แบบใหมชวยใหงายในการก าหนดคาส าหรบงาน mill holes และ mill bosses
สามารถเรยกค าสงไดท
Initial release NX 9.0.1
Application Manufacturing
Command Finder Create Operation
Location in dialog box
Create Operation dialog box→Type list→hole_making→Operation Subtype
group→Boss Milling or Boss Thread Milling
Milling chamfers on holes
งาน chamfer ร สามารถใช Hole Chamfer Milling operation ส าหรบท า single chamfer บน multiple features
เลอก hole features เพอ chamfer หรอเลอก geometry จาก graphics window ซงอาจไมจ าเปนตองม chamfer บน model
87
ส าหรบ model chamfer เลอกพนท chamfer เพอท าการ chamfer หรอเลอก geometry จาก graphics window ส าหรบ model ทไมม chamfer ใหท าการเลอกผวทรงกระบอกของร และก าหนดขนาด counter sink diameter.
เมอองศาของ cutter tip ไมตรงกบองศาของ model chamfer
o Operation จะปลอยเนองานทงไว ถาองศาของ cutter นอยกวามมของชนงาน
o Tool gouges จะท างานเมอมมของ angle มากกวาองศาของชนงาน และรายงานผลการ gouges
ในสวนของ operation จะเปนตวก าหนดคาของ in-process feature ส าหรบท าการ chamfer และสรางวงกลมกดรอบขนาดของร
Chamfer in-process feature volume
Chamfer tool path
Tracking points
NX สามารใช tracking point ตามทคณเลอก
1 Tracking point บนจดทเหนเปนการใชจาก drive point ใน operation
Note เพราะการใช operation cuts chamfers บน holes ทงกบ model chamfer หรอไมม model chamfer NX จะใชวธการเลอก tracking point ถงแมวา tool จะกดเขาเนอ หรอกดอากาศกตาม
Contact and tracking data output
NX มออปชนในก าหนดการปลอยคา contact/tracking บน tool diameter มเชนนน NX จะ outputs tool path ทจดกงกลางปลาย tool อยางเดยว
สามารถเรยกค าสงไดท
88
Application Manufacturing
Prerequisite
รอบรบเครองมอตดประเภท chamfer mill, spot drill หรอ countersink ซง tool ตองมการก าหนดคาดงน
Defined tracking point.
Command Finder Create Operation
Location in dialog box
Hole Chamfer milling operation
Create Operation dialog box→Type list→hole_making→Hole Chamfer Milling
Selecting the tracking point
Hole Chamfer Milling dialog box→Path Settings group→Drive Point list
Machining through holes and blind holes together คณสามารถจดกลมรทะล และรทไมทะล เพอ machine ดวยกน จะชวยใหลดเวลาการท าโปรแกรม เพราะไมตองแยกโปรแกรมในการท างาน ดวยการก าหนดออปชนไวกอนของค าสง Group Features เพอจดกลมของ feature ซงมขอมลเหมอนกนไดแก diameters, thread pitch และ number of steps เมอถกจดกลมเขาดวยกนแลว NX จะละเวนคาทงหมดของ depth attributes, including tolerances, chamfers และ thread lengths
How it works
ใน NX, through holes คอ STEPxHOLE features และ blind holes คอ STEPxPOCKET features, โดยท x เปนตวระบจ านวนของ steps ในแตละ feature เมอจดกลม feature โดยใชออปชน Predefined, NX จะ
รวม STEP1HOLE และ STEP1POCKET features ทมขนาด diameters เหมอนกนเขาไปยงกลมของ FG_STEP1HOLE_STEP1POCKET feature
รวม STEP1HOLE_THREAD และ STEP1POCKET_THREAD features ทมขนาด diameters และระยะพตเหมอนกนเขาไปยงกลมของ FG_STEP1HOLE_THREAD_STEP1POCKET_THREAD feature
ท าตามขนตอนการท างานส าหรบ feature กบงาน multiple steps
ถาลกษณะของกลมจ าเปนตองมขนาดของ diameters ทแตกตางกน NX จะสรางชอกลมเปน FG_STEP1HOLE_STEP1POCKET_1, FG_STEP1HOLE_STEP1POCKET_2 และอนๆ
ตามตวอยางแสดงรปแบบของรทแตกตางกน และ NX จะท าการรวมกลมเขาดวยกนอยางไร
Features to group
89
Features to group
STEP1HOLE_1
STEP2HOLE_5
STEP1HOLE_2
STEP2HOLE_6
STEP1POCKET_3
STEP2POCKET_7
STEP1POCKET_4
STEP2POCKET_8
Features ใน Machining Feature Navigator หลงจากท าการ group
WORKPIECE
FG_STEP1HOLE_STEP1POCKET
STEP1HOLE_1
STEP1HOLE_2
STEP1POCKET_3
STEP1POCKET_4
FG_STEP2HOLE_STEP2POCKET
STEP2HOLE_5
STEP2HOLE_6
STEP2POCKET_7
STEP2POCKET_8 Sample part
Features selected for FG_STEP1HOLE_STEP1POCKET
90
Drilling operation for FG_STEP1HOLE_STEP1POCKET
ค าสง Group Features มออปชนดงน
None groups features ไมมคณลกษณะทเหมอนกน
All groups features only ถาคณลกษณะทงหมดเหมอนกน
สามารถเรยกค าสงไดท
Application Manufacturing
Machining Feature Navigator
Right-click in the background→Group Features
Grouping selected features
Right-click selected features→Group Features
Location in dialog box Group by group→Identical Attributes list →Predefined
91
Enhancements to control drilling depth คณสามารถควบคมความลกการเจาะ ส าหรบงาน drill และงาน step drill ไดตามแนวทางดงน
ใสคาบวก (1) หรอคาลบ (2) ใน bottom stock กบงาน blind holes
ใสคา bottom offset (1) กบงาน through holes
ใชออปชน MODEL_DEPTH กบงาน drill เพอหาคาความลกท tool ลงไปสมผสกบชนงาน
ใชออปชนน เพอควบคมความลกส าหรบรอนทมคณลกษณะไมเกยวของ หรอไมตองการ
ใชออปชน Position Tool Shoulder เพอก าหนด contact point วาจะอยท tool tip หรอ tool shoulder
Note ออปชน Position Tool Shoulder จะแยกออกจากออปชน MODEL_DEPTH
Drilling to tool contact depth
Use the MODEL_DEPTH option to drill to where the tool contacts the part. You control the drilling depth by choosing whether the tool contact point is at the tool tip or the tool shoulder. In the following example, (1) is a hole modeled with a flat bottom and (2) is a hole modeled with a tip angle.
92
Position Tool Shoulder =
Position Tool Shoulder =
ถาคณเจาะรทม tip angle แตกตางกนบนชนงาน operation จะเหลอเนองานไว หรอจะกนเนองานหายไป แลวแตคาของ drill tip
ถาคณใชลกษณะของ tool shoulder ในการก าหนดต าแหนง tool และ drill tip angle นอยกวา model tip angle จะได operation ทปลาย tool ลกลงไปมากกวาปลายของรเจาะ
ถาคณใชลกษณะของ tool shoulder ในการก าหนดต าแหนง tool และ drill tip angle มากกวา model tip angle จะได operation ทปลาย tool ไปไมถงปลายของรเจาะ
ตามตวอยางทแสดง รท model มองศาอยท 122°
Hole
102° drill tip
122° drill tip
130° drill tip
Position to tool shoulder
Gouges
Exact match
Leaves material
93
Position to tool tip
Leaves material
Exact match
Leaves material
Conical holes
ใชออปชน Model Depth และ Bottom Stock ชวยในการเจาะ conical holes จากตวอยางแสดง in-process features ส าหรบ operations ทใชกบงาน rough a tapered hole
Volume to drill: 5 mm through hole with conical taper from 8 mm to 13 mm
4 mm drill
Bottom Stock = 0
Bottom Offset = 1.0
5.5 mm drill
Bottom Stock = 0.1
94
8 mm drill
Bottom Stock = 0.1
10 mm drill
Bottom Stock = 1.0
Protecting part geometry below a through hole
ใชออปชน Model Depth และ Bottom Stock ส าหรบรทะล เมอตองการยดระยะความลกไปยง part geometry
Note เมอคณเลอก Model Depth และชนงานทะล tool path จะยดลงไปหา part geometry ทมอยดานลาง NX จะมองขามคา Bottom Offset ใน cutting parameter แต NX จะใชคาใน Bottom Stock แทน
จากตวอยางดานลางจะแสดง in-process features และผลทแตกตางของ tool path ระหวางออปชน Machining Area และ Bottom Stock
95
Machining Area = FACES_CYLINDER_1
Machining Area = MODEL_DEPTH
1 Bottom Stock = 0
(contact point)
Machining Area = MODEL_DEPTH
2 Bottom Stock = 5
Bottom Offset = 2
Bottom Offset = 2
Bottom Offset = 2
สามารถเรยกค าสงไดท
Application Manufacturing
Location in dialog box
Drilling to model depth
Feature Geometry dialog box→Common Parameters group→Machining Area list →MODEL_DEPTH
Positioning to the tool shoulder or tool tip
Feature Geometry dialog box→Common Parameters group→Cutting Parameters subgroup→Position Tool Shoulder
Adding bottom stock to blind holes
96
Feature Geometry dialog box→Common Parameters group→Cutting Parameters subgroup→Bottom Stock
Adding bottom offset to through holes
[Drilling operation] dialog box→Cutting Parameters→Cutting Parameters dialog box→Strategy tab→Extend Path group→Bottom Offset
Enhancements to optimize drill sequencing คณสามารถปรบล าดบรเจาะไดตามรปแบบดงน
จดเรยงรปแบบตามแบบ zig หรอ zig-zag เพอใหไดระยะทางทสนทสด จะใชลกษณะขนานกบแนวแกน หรอทศทางของแนวแกนทเราเปนคนก าหนด
Reverse ทศทางใน list hole หรอ boss
เลอกรเพอเปนก าหนดเปนรแรก หรอเปนรสดทาย
สามารถดทศทางการเจาะไดกอน โดยไมตองออกมา generate
Defining the hole sequence
คณสามารถจดล าดบของรไดใน HOLE_BOSS_GEOM geometry หรอจดล าดบไดใน operation
Operation Navigator — Geometry
WORKPIECE
HOLE_BOSS_GEOM Defines the default hole sequence (1).
SPOT_DRILLING Uses the default sequence.
DRILLING Modified to use a reversed hole sequence (2).
COUNTERSINKING Uses the default sequence.
97
ใชออปชน Reload List From Parent ใน operation ดงคาเขามาภายหลงจากมการแกไข parent sequence
Note ออปชน Sequence group ใน Hole or Boss Geometry และ Feature Geometry จะแสดงคาเบองตนเสมอ ล าดบจะท าการเปลยนแปลงตอเมอคลก Reorder List
Machining holes using a zig or zig-zag pattern
เพอลดระยะทาง จงมการจดเรยงรปแบบการเจาะตามแบบ zig หรอ zig-zag เมอไหรกตามทสามารถท าได NX จะใชลกษณะการเดนขนานกบแนวแกน หรอทศทางของแนวแกนทเราเปนคนก าหนด
จากตวอยางเปนการเปรยบเทยบระหวาง tool path ในรปแบบ zig และ zig-zag ทมจดเรมตนเดยวกน (1) point และตามทศทาง (2) X-axis
Zig pattern
Zig-zag pattern
จากตวอยางเปนการเปรยบเทยบระหวาง tool path รปแบบThe zig-zag ทมจดเรมตนเดยวกน (1) point แตปรบแนวแกนตางกน (2)
Primary direction along X-axis Primary direction along specified vector
98
Changing the start or end points
ท าการก าหนดจดเรมตน หรอจดสดทายของการเจาะ ดวยการคลกเลอกรใน list และเลอน Move to top หรอ Move
to Bottom .
Caution ไมแนะน าใหท าการระบจดสดทายในลกษณะการท างานของ Zig หรอ Zig-zag เพราะทาง NX จะท าการเลอกจดสดทายใหเอง
จากตวอยางเปนการเปรยบเทยบหนาตางการท างาน Hole or Boss Geometry เกยวกบ list และการ preview ล าดบของร กอนและหลงการเปลยนรเรมตน
STEP1HOLE_1 เปนรเรมตน
Item Name
1 2 3 4 5 . . . 25
STEP1HOLE_1 STEP1HOLE_2 STEP1HOLE_3 STEP1HOLE_4 STEP1HOLE_5 . . . STEP1HOLE_25
เปลยนต าแหนงเรมตนเปน STEP1HOLE_5 ซง NX จะยงคงซอเดมของรไว
Item Name
99
1 2 3 4 5 . . . 25
STEP1HOLE_5 STEP1HOLE_4 STEP1HOLE_3 STEP1HOLE_2 STEP1HOLE_1 . . . STEP1HOLE_21
สามารถเรยกค าสงไดท
Application Manufacturing
Location in dialog box
Defining the sequence for multiple operations
Hole or Boss Geometry dialog box
Defining the sequence for a single operation
[Drilling operation] dialog box→Geometry group→Specify Feature
Geometry→Feature Geometry dialog box
Changing the sequence start or end location
Hole or Boss Geometry or Feature Geometry dialog box→Feature group→List
subgroup→Move to top or Move to Bottom
Zig or zig-zag pattern sequence
Hole or Boss Geometry or Feature Geometry dialog box→Sequence group→Optimization→Primary Direction
Tracking points for drilling tools Tracking point คอจดอางองภายใน tool ท NX ใชในการค านวณ tool paths
100
Drilling tools มสอง tracking point ท center line คอ SYS_CL_SHOULDER และ SYS_CL_Tip
Step drills มการเพม tracking point ท center line ของแตละ step
For example, SYS_CL_STEP1_BOTTOM is located at the bottom of the first step.
คณสามารถก าหนด tracking points ทไหนกไดบน tool เพอใชกบ operation ของคณ
Using the tracking points in the drilling operation
คณสามารถก าหนดแยกกนระหวาง tracking points ส าหรบ non cutting และ cutting moves ในสวนของ drilling operation
เพอใหมนใจไดวาปลาย tool ไมสมผสงาน ดวยการเลอก tracking point ท tool tip ส าหรบ non cutting moves
เพอใหแนใจวาต าแหนง tool เขาถงความลกทตองการ ใหท าการเลอก tracking point ใหสอดคลองกบรเจาะ ตวอยางเชน การเลอกใชแบบ shoulder ของ tool drill หรอเลอก shoulder ของ step drill
NX จะเปลยนการอางอง tracking point ใหอตโนมตเมอรปแบบการเคลอนทในแตละแบบ ตวอยางเชน การก าหนด tracking point ใน operation ตามน
SYS_CL_Tip ใช tracking point ทปลาย tool กบทกต าแหนงในการเคลอนท
SYS_CL_SHOULDER ใช tracking point ท tool shoulder กบการเคลอนทใน drilling cycle
ถาใชงานกบงานเจาะอยางเชน Break Chip หรอ interrupted holes ใน operation จะใช
SYS_CL_Tip ส าหรบใชในการเคลอนท traversal, approach และ departure ดวย
101
SYS_CL_SHOULDER ส าหรบใชในการเคลอนท engage, cutting และ retract ภายใน drilling cycle
Example outputs for different drilling cycle tracking points
1 SYS_CL_TIP output:
GOTO/-25.352,89.572,-24.403
2 SYS_CL_SHOULDER output:
GOTO/-25.352,89.572,-22.000
สามารถเรยกค าสงไดท
Application Manufacturing
Prerequisite Drilling tool
Location in dialog box
Define the tracking point:
Drilling tool dialog box→More tab→Tracking group→Tracking Points→Tracking
Points dialog box
Set the tracking point for non cutting positioning moves:
[Drilling operation dialog box]→Tool group→Cutter Compensation subgroup→Tracking Data list
Note การระบ tracking point คณจะตองท าการ customize dialog box ส าหรบงาน drilling operation เพอใหมขอมล cutter compensation Tracking Data เพราะโดยพนฐานแลว NX จะไมไดเปดออปชน ซงจะใช tracking point ท tool tip centerline
102
Set the tracking point for the drilling cycle:
[Drilling operation dialog box]→Path Settings group→Cycle Tracking Data list
Integrated Simulation and Verification - ISV Finding machine, tool, and device components in a CAM or CMM setup
ใน NX, เมอคณเปดชนงานใน CAM setup, NX Manufacturing จะหา component parts อยางเชน machine tools ทใชส าหรบ simulation ซงในเวอรชนกอนหนาน เมอใช assembly load options ตามคา From Folder, NX จะคนหาชนสวนใน folder ทเลอกไว ดวยการใช variables ตามน
UGII_CAM_LIBRARY_INSTALLED_MACHINES_DIR
เรมใน NX 10, NX จะ search ไปยง library tools และ devices โดยการใช variables ตามน
UGII_CAM_LIBRARY_TOOL_DIR
UGII_CAM_LIBRARY_DEVICE_DIR
ใน CMM inspection, จะ search ไปยง folders ดวยการใช variables ตามน
UGII_INSPECTION_LIBRARY_INSTALLED_MACHINES_DIR
UGII_INSPECTION_LIBRARY_TOOL_DIR
UGII_INSPECTION_LIBRARY_DEVICE_DIR
ท าไมถงควรใช
คณสามารถใชคา assembly load option เปน From Folder, ถงแมวา CAM setup ของคณยงประกอบดวย machine tools, solid cutting tools และ devices
Note ถาคณแกไข locations คณตองแกไข variables อยางทแสดง
103
ใน version กอนหนาน ถาคณไมท าการตงคา search folders, NX จะไมแสดงชนงานอยางเชน chucks, tailstock และ cutting tools ในชนงานsim15_millturn_setup_sinumerik_mm_dual_sync.prt sample setup assembly.
ใน NX 10, แมวาจะขนค าเตอนวาหาบางชนงานไมพบ แตกยงคงแสดงชนสวนนนๆได
สามารถเรยกค าสงไดท
Initial release NX 10.0
Application Manufacturing
Prerequisite Open a part that has a CAM setup