WT20X-40取説表紙31YG0602
C 2002-2009 Honda Motor Co., Ltd. -All Rights Reserved
Owner,s Manual
WATER PUMPWT20X・WT30X・WT40X
Printed in Japan英 NAH HC
HiEM3
DIC F101(PF) BK
K2:WT40XK3:WT20X, WT30X
31YG060200X31-YG0-6020
2000.2009.03
Keep this owner’s manual handy, so you can refer to it at any time.This owner’s manual is considered a permanent part of the waterpump and should remain with the water pump if resold.
The information and specifications included in this publication were ineffect at the time of approval for printing. Honda Motor Co., Ltd.reserves the right, however, to discontinue or change specifications ordesign at any time without notice and without incurring any obligationwhatever. No part of this publication may be reproduced withoutwritten permission.
The engine exhaust from this productcontains chemicals known to the State
of California to cause cancer, birthdefects or other reproductive harm.
02/01/14 13:17:56 31YG0600_001
1
INTRODUCTION
Congratulations on your selection of a Honda water pump. We arecertain you will be pleased with your purchase of one of the finestwater pumps on the market.
We want to help you get the best results from your new water pumpand to operate it safely. This manual contains the information on howto do that; please read it carefully.
As you read this manual, you will find information preceded by asymbol. That information is intended to help you avoid
damage to your water pump, other property, or the environment.
We suggest you read the warranty policy to fully understand itscoverage and your responsibilities of ownership. The warranty policyis a separate document that should have been given to you by yourdealer.
When your water pump needs scheduled maintenance, keep in mindthat your Honda servicing dealer is specially trained in servicingHonda water pumps. Your Honda servicing dealer is dedicated to yoursatisfaction and will be pleased to answer your questions andconcerns.
Best Wishes,Honda Motor Co., Ltd.
02/01/14 13:18:03 31YG0600_002
2
INTRODUCTION
A FEW WORDS ABOUT SAFETY
Safety Labels
Safety Messages
Safety Headings
Safety Section
Instructions
Your safety and the safety of others are very important. And using thiswater pump safely is an important responsibility.
To help you make informed decisions about safety, we have providedoperating procedures and other information on labels and in thismanual. This information alerts you to potential hazards that couldhurt you or others.
Of course, it is not practical or possible to warn you about all thehazards associated with operating or maintaining a water pump. Youmust use your own good judgment.
You will find important safety information in a variety of forms,including:
–– on the pump.
–– preceded by a safety alert symbol and oneof three signal words, DANGER, WARNING, or CAUTION.
These signal words mean:
You WILL be KILLED or SERIOUSLY HURT ifyou don’t follow instructions.
You CAN be KILLED or SERIOUSLY HURT ifyou don’t follow instructions.
–– such as IMPORTANT SAFETY INFORMATION.
–– such as PUMP SAFETY.
–– how to use this pump correctly and safely.
This entire book is filled with important safety information –– pleaseread it carefully.
You CAN be HURT if you don’t followinstructions.
02/01/14 13:18:18 31YG0600_003
3
CONTENTS
..........................................................................................PUMP SAFETY . 5
........................................................................CONTROLS & FEATURES . 9
.............................................................................BEFORE OPERATION . 12
............................................................................................OPERATION . 15
.......................................................................SERVICING YOUR PUMP . 24
................................................IMPORTANT SAFETY INFORMATION . 5................................................................SAFETY LABEL LOCATIONS . 7
............................................COMPONENT & CONTROL LOCATIONS . 9..........................................................................................CONTROLS . 10
..............................................................................Fuel Valve Lever . 10.................................................................................Ignition Switch . 10
.....................................................................................Choke Lever . 10..................................................................................Throttle Lever . 11
...........................................................................Recoil Starter Grip . 11...........................................................................................FEATURES . 11
.............................................................................Oil Alert System . 11
...............................................ARE YOU READY TO GET STARTED? . 12........................................................IS YOUR PUMP READY TO GO? . 13
....................................Check the General Condition of the Pump . 13.......................................Check the Suction and Discharge Hoses . 14
.............................................................................Check the Engine . 14
...................................................SAFE OPERATING PRECAUTIONS . 15............................................................................PUMP PLACEMENT . 16
.......................................................SUCTION HOSE INSTALLATION . 17..................................................DISCHARGE HOSE INSTALLATION . 18
...........................................................................PRIMING THE PUMP . 18....................................................................STARTING THE ENGINE . 19...................................................................SETTING ENGINE SPEED . 21....................................................................STOPPING THE ENGINE . 22
............................................THE IMPORTANCE OF MAINTENANCE . 24....................................................................MAINTENANCE SAFETY . 25
..............................................................MAINTENANCE SCHEDULE . 26..........................................................................................REFUELING . 27
.............................................................FUEL RECOMMENDATIONS . 28................................................................ENGINE OIL LEVEL CHECK . 29
.........................................................................ENGINE OIL CHANGE . 30
09/02/16 10:46:04 31YG0600_004
4
CONTENTS
SERVICING YOUR PUMP (continued)
................................................................................................STORAGE . 41
.....................................................................................TRANSPORTING . 47
.....................................TAKING CARE OF UNEXPECTED PROBLEMS . 48
........................................TECHNICAL & CONSUMER INFORMATION . 50
...........................QUICK REFERENCE INFORMATION . Inside back cover
..................................................ENGINE OIL RECOMMENDATIONS . 31....................................................................AIR FILTER INSPECTION . 32
.......................................................................AIR FILTER CLEANING . 33...............................................................SEDIMENT CUP CLEANING . 34
.......................................................................SPARK PLUG SERVICE . 35...............................SPARK ARRESTER SERVICE (applicable types) . 37
................................................................PUMP CASING CLEANING . 39
..................................................................STORAGE PREPARATION . 41...........................................................................................Cleaning . 41
...................................................................................................Fuel . 42.........................................................................................Engine Oil . 45
.................................................................STORAGE PRECAUTIONS . 45..............................................................REMOVAL FROM STORAGE . 46
................................................................................................ENGINE . 48......................................................................Engine Will Not Start . 48
........................................................................Engine Lacks Power . 48...................................................................................................PUMP . 49
.............................................................................No Pump Output . 49...........................................................................Low Pump Output . 49
...............................................................TECHNICAL INFORMATION . 50..................................................................Serial Number Location . 50
..................Carburetor Modification for High Altitude Operation . 51..........................................Emission Control System Information . 52
..................................................................................Specifications . 54..............................................................CONSUMER INFORMATION . 57
.........................................................................Honda Publications . 57.......................................................Customer Service Information . 58
07/05/29 13:24:28 31YG0600_005
5
IMPORTANT SAFETY INFORMATION
Refuel With Care
Pump Operation
Operator Responsibility
PUMP SAFETY
Gasoline is extremely flammable, and gasoline vapor can explode.Refuel outdoors, in a well-ventilated area, with the engine stopped andthe pump on a level surface. Do not fill the fuel tank above the fuelstrainer shoulder. Never smoke near gasoline, and keep other flamesand sparks away. Always store gasoline in an approved container.Make sure that any spilled fuel has been wiped up before starting theengine.
Pump only water that is not intended for human consumption.Pumping flammable liquids, such as gasoline or fuel oils, can result ina fire or explosion, causing serious injury. Pumping sea water,beverages, acids, chemical solutions, or any other liquid thatpromotes corrosion can damage the pump.
Be sure that anyone who operates the pump receives properinstruction. Do not let children operate the pump. Keep children andpets away from the area of operation.
It is the operator’s responsibility to provide the necessary safeguardsto protect people and property. Know how to stop the pump quickly incase of emergency. If you leave the pump for any reason, always turnthe engine off. Understand the use of all controls and connections.
Most accidents can be prevented if you follow all instructions in thismanual and on the pump. The most common hazards are discussedbelow, along with the best way to protect yourself and others.
Honda WT20X, WT30X, and WT40X pumps are designed to pump onlyfresh water that is not intended for human consumption, and otheruses can result in injury to the operator or damage to the pump andother property.
02/01/14 13:18:36 31YG0600_006
6
PUMP SAFETY
Hot Exhaust
Carbon Monoxide Hazard
The muffler becomes very hot during operation and remains hot for awhile after stopping the engine. Be careful not to touch the mufflerwhile it is hot. Let the engine cool before transporting the pump orstoring it indoors.
To prevent fire hazards, keep the pump at least 3 feet (1 meter) awayfrom building walls and other equipment during operation. Do notplace flammable objects close to the engine.
Exhaust gas contains poisonous carbon monoxide. Avoid inhalation ofexhaust gas. Never run the engine in a closed garage or confined area.
02/01/14 13:18:42 31YG0600_007
7
PUMP SAFETY
SAFETY LABEL LOCATIONS
WT20XPUMP CAUTION LABEL
The labels shown here contain important safety information. Pleaseread them carefully. These labels are considered permanent parts ofyour pump. If a label comes off or becomes hard to read, contact anauthorized Honda servicing dealer for a replacement.
09/09/03 12:26:31 31YG0600_008
8
PUMP SAFETY
PUMP CAUTION LABEL
WT30X · WT40X
09/09/03 12:26:41 31YG0600_009
< >
9
COMPONENT & CONTROL LOCATIONS
WT20X
CONTROLS & FEATURES
THROTTLE LEVER
CHOKE LEVER
STARTER GRIP
FUEL VALVE LEVER
IGNITION SWITCH
OIL FILLER CAP/DIPSTICK
PRIMING WATER FILLER CAP
SUCTION PORT
STRAINER
FUEL FILLER CAP
AIR CLEANER
CASE DRAIN PLUG
DISCHARGE PORT
MUFFLER
PRIMING WATER FILLER CAP
WRENCH
PUMP DRAIN PLUG
09/02/16 10:46:29 31YG0600_010
10
CONTROLS & FEATURES
CONTROLS
Fuel Valve Lever
Ignition Switch
Choke Lever
ON
ON
OOFFFF
FUEL VALVE LEVER
OOFFFF
IGNITION SWITCH
CHOKE LEVER
CCLLOOSSEEDD
OOPPEENN
The fuel valve opens and closesthe connection between the fueltank and the carburetor.
The fuel valve lever must be in theON position for the engine to run.
When the engine is not in use,leave the fuel valve lever in theO F F p o s i t i o n t o p r e v e n tcarburetor flooding and to reducethe possibility of fuel leakage.
The ignition switch controls theignition system.
The ignition switch must be in theON position for the engine to run.
Turning the ignition switch to theOFF position stops the engine.
The OPEN position provides thecorrect fuel mixture for operationafter starting, and for restarting awarm engine.
The CLOSED position enrichesthe fuel mixture for starting a coldengine.
The choke lever opens and closesthe choke valve in the carburetor.
09/02/16 10:46:41 31YG0600_011
11
CONTROLS & FEATURES
Throttle Lever
Recoil Starter Grip
FEATURES
Oil Alert System
SLOW
THROTTLE LEVER
CHOKE LEVER
FFAASSTT
The throttle lever controls enginespeed.
Moving the throttle lever in thedirections shown makes theengine run faster or slower.
Pump output is controlled byadjusting the throttle lever. Atmaximum throttle position, thepump will deliver the highestoutput volume. Moving thethrottle lever toward the idleposition will decrease the outputvolume of the pump.
Pulling the starter grip operatesthe recoil starter to crank theengine for starting.
The Oil Alert system is designed to prevent engine damage caused byan insufficient amount of oil in the crankcase. Before the oil level in thecrankcase can fall below a safe limit, the Oil Alert system willautomatically stop the engine (the ignition switch will remain in theON position).
If the engine stops and will not restart, check the engine oil level (page) before troubleshooting in other areas.29
09/02/16 10:46:50 31YG0600_012
12
BEFORE OPERATION
ARE YOU READY TO GET STARTED?
Knowledge
Your safety is your responsibility. A little time spent in preparation willsignificantly reduce your risk of injury.
Read and understand this manual. Know what the controls do andhow to operate them.
Familiarize yourself with the pump and its operation before you beginpumping. Know what to do in case of emergencies.
Be sure of what you are pumping. This pump is designed to pumponly fresh water that is not intended for human consumption.
09/02/16 10:46:56 31YG0600_013
13
BEFORE OPERATION
IS YOUR PUMP READY TO GO?
Check the General Condition of the Pump
For your safety, and to maximize the service life of your equipment, itis very important to take a few moments before you operate the pumpto check its condition. Be sure to take care of any problem you find, orhave your servicing dealer correct it, before you operate the pump.
Improperly maintaining this pump,or failing to correct a problembefore operation, could cause amalfunction in which you could beseriously injured.
Always perform a preoperationinspection before each operation,and correct any problem.
Exhaust gas contains poisonous carbon monoxide. Avoid inhalation ofexhaust gas. Never run the engine in a closed garage or confined area.
To prevent fire hazards, keep the pump at least 3 feet (1 meter) awayfrom building walls and other equipment during operation. Do notplace flammable objects close to the engine.
Before beginning your preoperation checks, be sure the pump is on alevel surface and the ignition switch is in the OFF position.
Look around and underneath the pump for signs of oil or gasolineleaks.
Remove any excessive dirt or debris, especially around the enginemuffler, and recoil starter.
Look for signs of damage.
Check that all nuts, bolts, screws, hose connectors and clamps aretightened.
02/01/14 13:19:52 31YG0600_014
14
BEFORE OPERATION
Check the Suction and Discharge Hoses
Check the Engine
Check the general condition of the hoses. Be sure the hoses are inserviceable condition before connecting them to the pump.Remember that the suction hose must be reinforced construction toprevent hose collapse.
Check that the sealing washer in the suction hose connector is ingood condition (see page ).
Check that the hose connectors and clamps are securely installed(see pages and ).
Check that the strainer is in good condition and is installed on thesuction hose (see page ).
Check the oil level (see page ). To avoid the inconvenience of anunexpected shutdown by the Oil Alert system, always check theengine oil level before startup.
Check the air filter (see page ). A dirty air filter will restrict air flowto the carburetor, reducing engine and pump performance.
Check the fuel level (see page ). Starting with a full tank will helpto eliminate or reduce operating interruptions for refueling.
17
17
17
29
27
32
18
07/05/29 13:24:45 31YG0600_015
15
OPERATION
SAFE OPERATING PRECAUTIONS
To safely realize the full potential of this pump, you need a completeunderstanding of its operation and a certain amount of practice withits controls.
Before operating the pump for the first time, please review theIMPORTANT SAFETY INFORMATION on page and the chapter titledBEFORE OPERATION.
For your safety, avoid starting or operating the engine in an enclosedarea, such as a garage. Your engine’s exhaust contains poisonouscarbon monoxide gas which can collect rapidly in an enclosed areaand cause illness or death.
Pump only fresh water that is not intended for human consumption.Pumping flammable liquids, such as gasoline or fuel oils, can result ina fire or explosion, causing serious injury. Pumping sea water,beverages, acids, chemical solutions, or any other liquid thatpromotes corrosion can damage the pump.
5
02/01/14 13:20:09 31YG0600_016
16
OPERATION
PUMP PLACEMENT
SUCTIONHEAD
DISCHARGEHEAD
TTOOTTAALL HHEEAADD
For best pump performance, place the pump near the water level, anduse hoses that are no longer than necessary. That will enable thepump to produce the greatest output with the least self-priming time.
As head (pumping height) increases, pump output decreases. Thelength, type, and size of the suction and discharge hoses can alsosignificantly affect pump output.
Discharge head capability is always greater than suction headcapability, so it is important for suction head to be the shorter part oftotal head.
Minimizing suction head (placing the pump near the water level) isalso very important for reducing self-priming time. Self-priming timeis the time it takes the pump to bring water the distance of the suctionhead during initial operation.
09/02/16 10:47:01 31YG0600_017
17
OPERATION
SUCTION HOSE INSTALLATION
HOSE CONNECTOR SUCTION HOSE
HOSE CLAMP
HOSE CLAMP RING
SUCTION PORT
STRAINER
HOSE CLAMP
HOSE CLAMPHHOOSSEE CCOONNNNEECCTTOORR
SUCTIONHOSE
SEALING WASHER (commercially available)
HOSE COUPLER (commercially available)
SUCTION HOSE(commerciallyavailable)
Use the commercially available hose and hose connector with thehose clamp provided with the pump. The suction hose must bereinforced with a noncollapsible wall or braided wire construction.
The suction hose should be no longer than necessary. Pumpperformance is best when the pump is near the water level, and thehoses are short.
Use a hose clamp to securely fasten the hose connector to the suctionhose in order to prevent air leakage and loss of suction. Verify that thehose connector sealing washer is in good condition.
Install the strainer (provided with the pump) on the other end of thesuction hose, and secure it with a hose clamp. The strainer will help toprevent the pump from becoming clogged or damaged by debris.
Securely tighten the hose connector on the pump suction port.
02/01/14 13:20:28 31YG0600_018
18
OPERATION
DISCHARGE HOSE INSTALLATION
PRIMING THE PUMP
HOSE CONNECTOR
HOSE CLAMP
DISCHARGE HOSE
PRIMING WATER FILLER CAP
WATER
Use a commercially availablehose and hose connector, andclamp provided with the pump.
It is best to use a short, large-diameter hose, because that willreduce fluid friction and improvepump performance. A long orsmall-diameter hose will increasefluid friction and reduce pumpoutput.
Tighten the hose clamp securelyto prevent the discharge hosefrom disconnecting under highpressure.
Before starting the engine, remove the filler cap from the pumpchamber, and completely fill the pump chamber with water. Reinstallthe filler cap, and tighten it securely.
Operating the pump dry will destroy the pump seal. If the pump hasbeen operated dry, stop the engine immediately, and allow the pumpto cool before priming.
3.70 US gal (14.0 , 3.08 Imp gal)3.96 US gal (15.0 , 3.30 Imp gal)
Priming water capacity:WT20X:WT30X, WT40X:
02/01/14 13:20:38 31YG0600_019
19
OPERATION
STARTING THE ENGINE
FFUUEELL VVAALLVVEE LLEEVVEERR
CHOKE LEVER
THROTTLE LEVER
CCLLOOSSEEDD
ON
FFAASSTT
Move the fuel valve lever to the ON position.
Move the throttle lever away from the SLOW position, about 1/3 ofthe way toward the FAST position.
To restart a warm engine, leave the choke lever in the OPEN position.
To start a cold engine, move the choke lever to the CLOSED position.
1.
2.
3.
02/01/14 13:20:48 31YG0600_020
20
OPERATION
ON
IGNITION SWITCH
STARTER GRIP
Directionto pull
Turn the ignition switch to the ON position.
Pull the starter grip lightly until you feel resistance, then pull brisklyin the direction of the arrow as shown below.Return the starter grip gently.
4.
5.
07/05/29 13:24:52 31YG0600_021
21
OPERATION
SETTING ENGINE SPEED
CHOKE LEVER
SLOW
OOPPEENN
FFAASSTT
THROTTLE LEVER
If the choke lever was moved to the CLOSED position to start theengine, gradually move it to the OPEN position as the engine warmsup.
After starting the engine, move the throttle lever to the FAST positionfor self-priming, and check pump output.
Pump output is controlled by adjusting engine speed. Moving thethrottle lever in the FAST direction will increase pump output, andmoving the throttle lever in the SLOW direction will decrease pumpoutput.
6.
02/01/14 13:21:02 31YG0600_022
22
OPERATION
STOPPING THE ENGINE
THROTTLE LEVER
SLOW
IGNITION SWITCH
OOFFFF
To stop the engine in an emergency, simply turn the ignition switch tothe OFF position. Under normal conditions, use the followingprocedure.
Move the throttle lever to the SLOW position.
Turn the ignition switch to the OFF position.
1.
2.
02/01/14 13:21:09 31YG0600_023
23
OPERATION
FUEL VALVE LEVER
OOFFFF
Turn the fuel valve lever to the OFF position.
After use, remove the pump drain plug (see page ), and drain thepump chamber. Remove the filler cap, and flush the pump chamberwith clean, fresh water. Allow the water to drain from the pumpchamber, then reinstall the filler cap and drain plug.
3.
39
02/01/14 13:21:14 31YG0600_024
24
SERVICING YOUR PUMP
THE IMPORTANCE OF MAINTENANCE
Maintenance, replacement, or repair of emission control devices andsystems may be performed by any engine repair establishment orindividual, using parts that are ‘‘certified’’ to EPA standards.
Good maintenance is essential for safe, economical, and trouble-freeoperation. It will also help reduce air pollution.
Improperly maintaining this pump,or failure to correct a problembefore operation, can cause amalfunction in which you can beseriously hurt or killed.
Always follow the inspection andmaintenance recommendations andschedules in this owner’s manual.
To help you properly care for your pump, the following pages includea maintenance schedule, routine inspection procedures, and simplemaintenance procedures using basic hand tools. Other service tasksthat are more difficult, or require special tools, are best handled byprofessionals and are normally performed by a Honda technician orother qualified mechanic.
The maintenance schedule applies to normal operating conditions. Ifyou operate your pump under severe conditions, such as sustainedhigh-load or high-temperature operation, or use in unusually wet ordusty conditions, consult your servicing dealer for recommendationsapplicable to your individual needs and use.
Remember that your servicing dealer knows your pump best and isfully equipped to maintain and repair it.
To ensure the best quality and reliability, use only new, genuineHonda parts or their equivalents for repair and replacement.
02/01/14 13:21:23 31YG0600_025
-
-
-
25
SERVICING YOUR PUMP
MAINTENANCE SAFETY
Safety Precautions
Carbon monoxide poisoning from engine exhaust.
Burns from hot parts.
Injury from moving parts.
Some of the most important safety precautions follow. However, wecannot warn you of every conceivable hazard that can arise inperforming maintenance. Only you can decide whether or not youshould perform a given task.
Failure to properly followmaintenance instructions andprecautions can cause you to beseriously hurt or killed.
Always follow the procedures andprecautions in the owner’s manual.
Make sure the engine is off before you begin any maintenance orrepairs. This will eliminate several potential hazards:
Be sure there is adequate ventilation whenever you operate theengine.
Let the engine and exhaust system cool before touching.
Do not run the engine unless instructed to do so.
Read the instructions before you begin, and make sure you have thetools and skills required.
To reduce the possibility of fire or explosion, be careful whenworking around gasoline. Use only a nonflammable solvent, notgasoline, to clean parts. Keep cigarettes, sparks, and flames awayfrom all fuel-related parts.
02/01/14 13:21:33 31YG0600_026
*
○
○
○
○
○*
○
○○
○○○
○
○○
○
○
---
-----
26
SERVICING YOUR PUMP
MAINTENANCE SCHEDULE
ITEMREGULAR SERVICE PERIOD (3)
Perform at every indicatedmonth or operating hourinterval, whichever comes first.
Check levelChangeCheckCleanReplaceCleanClean-adjustReplaceClean
Check-adjustCheck-adjustClean
CleanCheckCheckCheckCheck
Engine oil
Air filter
Sediment cupSpark plug
Spark arrester(optional parts)Idle speedValve clearanceCombustionchamberFuel tank and filterFuel tubeImpellerImpeller clearancePump inlet valve
(1)
Every 2 years (Replace if necessary) (2)
After every 500 hrs. (2)
Eachuse
(2)(2)
(2)(2)(2)
(2)
Referto
page
29303233333435
37
Emission-related items.
Service more frequently when used in dusty areas.
These items should be serviced by your servicing dealer, unless youhave the proper tools and are mechanically proficient. Refer to Hondashop manual for service procedures.
For commercial use, log hours of operation to determine propermaintenance intervals.
Replace the paper element type only.
(2)
(1)
(3)
Firstmonth
or20 hrs.
Every3 months
or50 hrs.
Everyyearor
300 hrs.
Every6 months
or100 hrs.
02/01/14 13:21:46 31YG0600_027
27
SERVICING YOUR PUMP
REFUELING
MAXIMUM FUEL LEVEL
Remove the fuel tank cap and check the fuel level.If the fuel level is low, refuel in a well-ventilated area with the enginestopped. If the engine has been running, allow it to cool first. Neverrefuel the engine inside a building where gasoline fumes can reachflames or sparks. Refuel carefully to avoid spilling fuel. Do not fillabove the maximum fuel level.
Gasoline is highly flammable andexplosive.
You can be burned or seriouslyinjured when handling fuel.
Stop the engine and keep heat,sparks, and flame away.Handle fuel only outdoors.Wipe up spills immediately.
After refueling, tighten the fuel tank cap securely.
07/05/29 13:25:00 31YG0600_028
28
SERVICING YOUR PUMP
FUEL RECOMMENDATIONS
Spilled fuel is not only a fire hazard, it causes environmental damage.Wipe up spills immediately.
Fuel can damage paint and plastic. Be careful not to spill fuel whenfilling your fuel tank. Damage caused by spilled fuel is not coveredunder the Distributor’s Limited Warranty.
This engine is certified to operate on unleaded gasoline with a pumpoctane rating of 86 or higher.
You may use regular unleaded gasoline containing no more than 10%Ethanol (E10) or 5% Methanol by volume. In addition, Methanol mustcontain cosolvents and corrosion inhibitors.
Use of fuels with content of Ethanol or Methanol greater than shownabove may cause starting and/or performance problems. It may alsodamage metal, rubber, and plastic parts of the fuel system.
Engine damage or performance problems that result from using a fuelwith percentages of Ethanol or Methanol greater than shown aboveare not covered under warranty.
Never use stale or contaminated gasoline or an oil/gasoline mixture.Avoid getting dirt or water in the fuel tank.
07/05/29 13:25:09 31YG0600_029
29
SERVICING YOUR PUMP
ENGINE OIL LEVEL CHECK
OIL FILLER CAP/DIPSTICK
OIL FILLER NECK
UPPER LIMIT
Check the engine oil level with the engine stopped and in a levelposition.
Remove the oil filler cap/dipstick and wipe it clean.
Insert and remove the dipstick without screwing it into the filler neck.Check the oil level shown on the dipstick.
If the oil level is low, fill to the edge of the oil filler hole with therecommended oil (see page ).
Screw in the oil filler cap/dipstick securely.
Running the engine with a low oil level can cause engine damage. Thistype of damage is not covered by the Distributor’s Limited Warranty.
The Oil Alert system will automatically stop the engine before the oillevel falls below safe limits. However, to avoid the inconvenience of anunexpected shutdown, check the oil level regularly.
1.
2.
3.
4.
31
07/05/29 13:25:20 31YG0600_030
30
SERVICING YOUR PUMP
ENGINE OIL CHANGE
OIL LEVEL
DRAIN PLUG
OIL FILLER CAP/DIPSTICK
Drain the used oil while the engine is warm. Warm oil drains quicklyand completely.
Place a suitable container below the engine to catch the used oil,then remove the oil filler cap/dipstick and the drain plug.
Allow the used oil to drain completely, then reinstall the drain plug,and tighten it securely.
Please dispose of used motor oil in a manner that is compatible withthe environment. We suggest you take used oil in a sealed containerto your local recycling center or service station for reclamation. Donot throw it in the trash, pour it on the ground, or down a drain.
With the engine in a level position, fill to the edge of the oil filler holewith the recommended oil (see page ).
Screw in the oil filler cap/dipstick securely.
The Oil Alert system will automatically stop the engine before the oillevel falls below the safe limit. However, to avoid the inconvenienceof an unexpected shutdown, fill to the upper limit, and check the oillevel regularly.
0.63 US qt (0.60 )1.2 US qt (1.1 )
1.
2.
3.
4.
Engine oil capacity:WT20X................WT30X/WT40X..
31
07/05/29 13:25:31 31YG0600_031
31
SERVICING YOUR PUMP
ENGINE OIL RECOMMENDATIONS
AMBIENT TEMPERATURE
SAE 10W-30 is recommended for general use. Other viscosities shownin the chart may be used when the average temperature in your area iswithin the indicated range.
Use 4-stroke motor oil that meets or exceeds the requirements for APIservice category SJ or later (or equivalent). Always check the APIservice label on the oil container to be sure it includes the letters SJ orlater (or equivalent).
The SAE oil viscosity and service category are in the API label on theoil container. Honda recommends that you use API SERVICE categorySJ or later (or equivalent) oil.
07/05/29 13:25:38 31YG0600_032
32
SERVICING YOUR PUMP
AIR FILTER INSPECTION WING NUT
AIR FILTER
AIR CLEANERCOVER
Unscrew the wing nut andremove the air cleaner cover.Check the air filter to be sure itis clean and in good condition.
If the air filter is dirty, clean it asdescribed on page . Replacethe air filter if it is damaged.
Operating the engine without an air filter, or with a damaged air filter,will allow dirt to enter the engine, causing rapid engine wear. This typeof damage is not covered by the Distributor’s Limited Warranty.
Reinstall the air cleaner cover,and tighten the wing nutsecurely.
1.
2.
3.
33
07/05/29 13:25:46 31YG0600_033
33
SERVICING YOUR PUMP
AIR FILTER CLEANING
WING NUT
WING NUT
AIR CLEANERCOVER
PAPERFILTERELEMENT
FOAMFILTERELEMENT
A dirty air filter will restrict air flow to the carburetor, reducing engineperformance. If you operate the pump in very dusty areas, clean theair filter more frequently than specified in the Maintenance Schedule(see page ).
Unscrew the wing nut from theair cleaner cover, and removethe air cleaner cover.Unscrew the wing nut from theair filter, and remove the airfilter.
Reinstall the air cleaner cover, and tighten the wing nut securely.
Place the foam air filter element over the paper air filter element,and install the assembled air filter. Be sure the gasket is in placebeneath the filter. Tighten the wing nut securely.
Wipe dirt from the air cleaner base and cover (and silencer ifapplicable), using a moist rag.
Foam air filter element: Wash in warm, soapy water, then rinsethoroughly, or wash in non-flammable solvent. Allow the filterelement to dry thoroughly. Dip the filter element in clean engine oil,then squeeze out all excess oil. The engine will smoke when startedif too much oil is left in the filter element.
Paper air filter element: Tap thefilter element several times on ahard surface to remove dirt, orblow compressed air [notexceeding 30 psi (270 kPa, 2.1kg/cm )] through the filterelement from the inside out.Never try to brush off dirt;brushing will force dirt into thefibers.
Separate the foam and paperair filter elements. Check bothfilter elements, and replacethem if they are damaged.Always replace the paper airfilter element every year or 300hours. Clean the air filterelements if they are to bereused.
1.
2.
3.
4.
5.
6.
26
07/05/29 13:25:57 31YG0600_034
34
SERVICING YOUR PUMP
SEDIMENT CUP CLEANING
SEDIMENT CUP
Move the fuel valve lever to the OFF position, then remove the fuelsediment cup and O-ring.
Gasoline is highly flammable andexplosive.
You can be burned or seriouslyinjured when handling fuel.
Stop the engine and keep heat,sparks, and flame away.Handle fuel only outdoors.Wipe up spills immediately.
Place the O-ring in the fuel valve, and install the sediment cup.Tighten the sediment cup securely.
Move the fuel valve lever to the ON position, and check for leaks.Replace the O-ring if there is any leakage.
Wash the sediment cup in non-flammable solvent, and dry itthoroughly.
1.
2.
3.
4.
07/05/29 13:26:07 31YG0600_035
- -
--
35
SERVICING YOUR PUMP
SPARK PLUG SERVICE
SPARK PLUG WRENCH
SPARK PLUG CAP
0.028 0.031 in(0.70 0.80 mm)
In order to service the spark plug, you will need a spark plug wrench(commercially available).
Incorrect spark plugs can cause engine damage.
Disconnect the spark plug cap, and remove any dirt from around thespark plug area.
Remove the spark plug with a 13/16-inch spark plug wrench.
BPR6ESW20EPR-U
0.028 0.031 in (0.70 0.80 mm)
Measure the spark p lugelectrode gap with a suitablegauge.Correct the gap, if necessary, bycarefully bending the sideelectrode.The gap should be:
Inspect the spark plug. Replaceit if the electrodes are worn, orif the insulator is cracked orchipped. Clean the spark plugwith a wire brush if you aregoing to reuse it.
1.
2.
3.
4.
Recommended spark plug: (NGK)(DENSO)
02/01/14 13:23:22 31YG0600_036
-
36
SERVICING YOUR PUMP
Attach the spark plug cap.
A loose spark plug can overheat and damage the engine.Overtightening the spark plug can damage the threads in thecylinder head.
If installing a new spark plug, tighten 1/2 turn after the spark plugseats.
If reinstalling the used spark plug, tighten 1/8 1/4 turn after thespark plug seats.
After the spark plug seats, tighten with a 13/16-inch spark plugwrench to compress the washer.
Install the spark plug carefully, by hand, to avoid cross-threading.
6.
7.
5.
02/01/14 13:23:30 31YG0600_037
37
SERVICING YOUR PUMP
SPARK ARRESTER SERVICE (optional equipment)
WT20X
MUFFLER
MUFFLER PROTECTOR
SPARK ARRESTER
4 mm SCREW
5 mm SCREW (4)
Your engine is not factory-equipped with a spark arrester. In someareas, it is illegal to operate an engine without a spark arrester. Checklocal laws and regulations. A spark arrester is available fromauthorized Honda servicing dealers.
The spark arrester must be serviced every 100 hours to keep itfunctioning as designed.
If the engine has been running, the muffler will be very hot. Allow themuffler to cool before servicing the spark arrester.
Remove the 4 mm screw from the spark arrester, and remove thespark arrester from the muffler.
Remove the 5 mm screws from the muffler protector, and removethe muffler protector.
1.
2.
02/01/14 13:23:40 31YG0600_038
38
SERVICING YOUR PUMP
MUFFLER
SPARK ARRESTER
SPARK ARRESTER SCREEN
4 mm SCREW
5 mm SCREW (2)
5 mm SCREW (4)
SPARK ARRESTER
4 mmSCREW (2)
WT40X typeuses two 4 mmscrews.
MUFFLER PROTECTOR
WT30X and WT40X
Install the spark arrester, muffler protector, and muffler in thereverse order of disassembly.
The spark arrester must be free of breaks and holes. Replace thespark arrester if it is damaged.
Use a brush to remove carbon deposits from the spark arresterscreen. Be careful to avoid damaging the screen.
3.
4.
02/01/14 13:23:47 31YG0600_039
39
SERVICING YOUR PUMP
PUMP CASING CLEANING
Removal:
WRENCH
WRENCH
DRAIN PLUG
WRENCHKNOBS (4)
KNOBS (4)
PUMP CASING
PUMP COVER
VOLUTECASE
O-RING
After each use, clean the inside of the pump casing using the followingprocedure:
Remove the drain plug from the pump cover using the wrench todrain the water inside.
Loosen the pump cover knobsusing the wrench.
Remove the pump cover andthe volute case from the pumpcasing, and remove any debrisfrom pump casing and volutecase.
1.
2.
3.
02/01/14 13:23:58 31YG0600_040
40
SERVICING YOUR PUMP
Installation:
VOLUTE CASE
PUMP CASING
PUMP COVERWRENCH
DRAIN PLUG
KNOBS (4)
O-RING
Install the drain plug in the pump cover.
After tightening the pump cover knobs, check the pump cover andpump casing to ensure that there is no water leakage.
Install the O-ring on the pump cover, taking care not to damage theO-ring.
Install the pump cover on the pump casing, and tighten the knobshand tight. Then, set the wrench to the knobs and finish tighteningthe knobs evenly.
1.
2.
3.
4.
02/01/14 13:24:07 31YG0600_041
41
STORAGE
STORAGE PREPARATION
Cleaning
Proper storage preparation is essential for keeping your pumptroublefree and looking good. The following steps will help to keeprust and corrosion from impairing your pump’s function andappearance, and will make the engine easier to start when you use thepump again.
Wash the engine and pump.
Wash the engine by hand, and be careful to prevent water fromentering the air cleaner or muffler opening. Keep water away fromcontrols and all other places that are difficult to dry, as waterpromotes rust.
Using a garden hose or pressure washing equipment can forcewater into the air cleaner or muffler opening. Water in the aircleaner will soak the air filter, and water that passes through theair filter or muffler can enter the cylinder, causing damage.
Water contacting a hot engine can cause damage. If the enginehas been running, allow it to cool for at least half an hour beforewashing.
Wipe dry all accessible surfaces.
Fill the pump chamber with clean, fresh water, start the engineoutdoors, and let it run until it reaches normal operatingtemperature to evaporate any external water.
Dry operation will damage the pump seal. Be sure the pumpchamber is filled with water before starting the engine.
1.
2.
3.
02/01/14 13:24:17 31YG0600_042
42
STORAGE
Fuel
DRAIN PLUG
Stop the engine, and allow it tocool.
You can extend fuel storage life by adding a fuel stabilizer that isformulated for that purpose, or you can avoid fuel deteriorationproblems by draining the fuel tank and carburetor.
The Distributor’s Limited Warranty does not cover fuel systemdamage or engine performance problems resulting from neglectedstorage preparation.
The length of time that gasoline can be left in your fuel tank andcarburetor without causing functional problems will vary with suchfactors as gasoline blend, your storage temperatures, and whether thefuel tank is partially or completely filled. The air in a partially filled fueltank promotes fuel deterioration. Very warm storage/temperaturesaccelerate fuel deterioration. Fuel deterioration problems may occurwithin a few months, or even less if the gasoline was not fresh whenyou filled the fuel tank.
Gasoline will oxidize and deteriorate in storage. Old gasoline willcause hard starting, and it leaves gum deposits that clog the fuelsystem. If the gasoline in your engine deteriorates during storage, youmay need to have the carburetor and other fuel system componentsserviced or replaced.
Remove the cover drain plug,and flush the pump with clean,fresh water. Allow the water todrain from the pump chamber,then reinstall the drain plugs.
After the pump is clean and dry,touch up any damaged paint,and coat areas that may rustwith a light film of oil. Lubricatecontrols with a silicone spraylubricant.
4.
5.
6.
02/01/14 13:24:28 31YG0600_043
43
STORAGE
Adding a Fuel Stabilizer to Extend Fuel Storage Life
FUEL VALVE LEVER
OOFFFF
When adding a fuel stabilizer, fill the fuel tank with fresh gasoline. Ifonly partially filled, air in the tank will promote fuel deteriorationduring storage. If you keep a container of gasoline for refueling, besure that it contains only fresh gasoline.
Add fuel stabilizer following the manufacturer’s instructions.
After adding a fuel stabilizer, run the engine outdoors for 10 minutesto be sure that treated gasoline has replaced the untreated gasolinein the carburetor.
Dry operation will damage the pump seal. Be sure the pumpchamber is filled with water before starting the engine.
Stop the engine, and move the fuel valve lever to the OFF position.3.
1.
2.
02/01/14 13:24:36 31YG0600_044
44
STORAGE
Draining the Fuel Tank and Carburetor
DRAIN BOLT
SEDIMENT CUP
Place an approved gasoline container below the carburetor, and usea funnel to avoid spilling fuel.
Remove the carburetor drain bolt and sediment cup, then move thefuel valve lever to the ON position.
Gasoline is highly flammable andexplosive.
You can be burned or seriouslyinjured when handling fuel.
Keep heat, sparks, and flameaway.Handle fuel only outdoors.Wipe up spills immediately.
After all the fuel has drained into the container, reinstall the drainbolt and sediment cup. Tighten them securely.
1.
2.
3.
02/01/14 13:24:45 31YG0600_045
-
45
STORAGE
Engine Oil
STORAGE PRECAUTIONS
Align notch on pulley withhole at top of cover.
Change the engine oil (see page ).
Remove the spark plug (see page ).
Pour a tablespoon (5 10 cc) of clean engine oil into the cylinder.
Pull the starter grip several times to distribute the oil in the cylinder.
Reinstall the spark plug.
Pull the starter grip slowly until resistance is felt and the notch onthe starter pulley aligns with the hole at the top of the recoil startercover. This will close the valves so moisture cannot enter the enginecylinder. Return the starter grip gently.
Unless all fuel has been drained from the fuel tank, leave the fuel valvelever in the OFF position to reduce the possibility of fuel leakage.
If possible, avoid storage areas with high humidity, because thatpromotes rust and corrosion.
If your pump will be stored with gasoline in the fuel tank andcarburetor, it is important to reduce the hazard of gasoline vaporignition. Select a well-ventilated storage area away from any appliancethat operates with a flame, such as a furnace, water heater, or clothesdryer. Also avoid any area with a spark-producing electric motor, orwhere power tools are operated.
1.
2.
3.
4.
5.
6.
30
35
02/01/14 13:24:58 31YG0600_046
46
STORAGE
REMOVAL FROM STORAGE
Place the pump on a level surface. Tilting can cause fuel or oil leakage.
With the engine and exhaust system cool, cover the pump to keep outdust. A hot engine and exhaust system can ignite or melt somematerials. Do not use sheet plastic as a dust cover. A nonporous coverwill trap moisture around the pump, promoting rust and corrosion.
Check your pump as described in the BEFORE OPERATION chapter ofthis manual.
If the fuel was drained during storage preparation, fill the tank withfresh gasoline. If you keep a container of gasoline for refueling, besure that it contains only fresh gasoline. Gasoline oxidizes anddeteriorates over time, causing hard starting.
If the cylinder was coated with oil during storage preparation, theengine may smoke briefly at startup. This is normal.
02/01/14 13:25:05 31YG0600_047
47
TRANSPORTING
If the pump has been running, allow the engine to cool for at least 15minutes before loading the pump on the transport vehicle. A hotengine and exhaust system can burn you and can ignite somematerials.
Keep the pump level when transporting to reduce the possibility offuel leakage. Move the fuel valve lever to the OFF position.
02/01/14 13:25:09 31YG0600_048
48
ENGINE
TAKING CARE OF UNEXPECTED PROBLEMS
Engine Will Not Start Possible Cause Correction
Engine Lacks Power Possible Cause Correction
Fuel valve OFF.
Choke open.
Ignition switch OFF.
Out of fuel.Bad fuel; pump storedwithout treating ordraining gasoline, orrefuel with badgasoline.Low oil level caused OilAlert to stop engine.Spark plug faulty,fouled, or improperlygapped.Spark plug wet withfuel (flooded engine).
Fuel filter clogged,carburetor malfunction,ignition malfunction,valves stuck, etc.
Air filter clogged.
Bad fuel; pump storedwithout treating ordraining gasoline, orrefuel with badgasoline.Fuel filter clogged,carburetor malfunction,ignition malfunction,valves stuck, etc.
Check air filter.
Check fuel.
Take engine to anauthorized Hondaservicing dealer, orrefer to shop manual.
Check controlpositions.
Check fuel.
Check engine oillevel.Remove and inspectspark plug.
Take engine to anauthorized Hondaservicing dealer, orrefer to shop manual.
Clean or replace filter(p. 33 ).Drain fuel tank andcarburetor (p. 44 ).Refuel with freshgasoline (p. 27 ).
Replace or repair faultycomponents asnecessary.
Move fuel valve leverto ON position.Move choke lever toCLOSED positionunless engine is warm.Turn ignition switch toON.Refuel (p. 27 )Drain fuel tank andcarburetor (p. 44 ).Refuel with freshgasoline (p. 27 ).
Add oil (p. 29 ).
Clean, gap, or replacespark plug (p. 35 ).
Dry and reinstall sparkplug. Start engine withthrottle lever in FASTposition.Replace or repair faultycomponents asnecessary.
1.
2.
3.
4.
5.
1.
2.
3.
02/01/14 13:25:23 31YG0600_049
49
TAKING CARE OF UNEXPECTED PROBLEMS
PUMP
No Pump Output Possible Cause Correction
Low Pump Output Possible Cause Correction
Check pumpchamber.Check suction hose.
Measure suction anddischarge head.
Check engine.
Check suction hose.
Check dischargehose.
Measure suction anddischarge head.
Check engine.
Prime pump (p. 18 )
Replace suction hose(p. 17 ).Sink the strainer andthe end of a suctionhose completelyunderwater.Replace sealing washerif missing or damaged.Tighten hose connectorand clamp (p. 17 ).Clean debris fromstrainer.Relocate pump and/orhoses to reduce head(p. 16 ).Move throttle to fast.
Pump not primed.
Hose collapsed, cut orpunctured.Strainer not completelyunderwater.
Air leak at connector.
Strainer clogged.
Excessive head.
Engine speed to slow.
Hose collapsed,damaged, too long, ordiameter too small.Air leak at connector.
Strainer clogged.
Hose damaged, toolong, or diameter toosmall.Marginal head.
Engine speed to slow.
Replace suction hose(p. 17 ).
Replace sealing washerif missing or damaged.Tighten hose connectorand clamp (p. 17 ).Clean debris fromstrainer.Replace dischargehose (p. 18 ).
Relocate pump and/orhoses to reduce head(p. 16 ).Move throttle to fast.
1.
2.
3.
4.
1.
2.
3.
4.
02/01/14 13:25:37 31YG0600_050
50
TECHNICAL & CONSUMER INFORMATION
TECHNICAL INFORMATION
Serial Number Location
ENGINE SERIAL NUMBER
FRAME SERIAL NUMBER
Engine serial number:
Record the frame serial number and the engine serial number in thespace below. You will need these serial numbers when ordering parts,and when making technical or warranty inquiries (see page ).
Frame serial number:
58
07/05/29 13:26:14 31YG0600_051
51
TECHNICAL & CONSUMER INFORMATION
Carburetor Modification for High Altitude Operation
At high altitude, the standard carburetor air-fuel mixture will be toorich. Performance will decrease, and fuel consumption will increase. Avery rich mixture will also foul the spark plug and cause hard starting.Operation at an altitude that differs from that at which this engine wascertified, for extended periods of time, may increase emissions.
High altitude performance can be improved by specific modificationsto the carburetor. If you always operate your pump at altitudes above5,000 feet (1,500 meters), have your servicing dealer perform this car-buretor modification. This engine, when operated at high altitude withthe carburetor modifications for high altitude use, will meet eachemission standard throughout its useful life.
Even with carburetor modification, engine horsepower will decreaseabout 3.5% for each 1,000-foot (300-meter) increase in altitude. Theeffect of altitude on horsepower will be greater than this if nocarburetor modification is made.
When the carburetor has been modified for high altitude operation,the air-fuel mixture will be too lean for low altitude use. Operation ataltitudes below 5,000 feet (1,500 meters) with a modified carburetormay cause the engine to overheat and result in serious engine damage.For use at low altitudes, have your servicing dealer return thecarburetor to original factory specifications.
02/01/14 13:25:52 31YG0600_052
52
TECHNICAL & CONSUMER INFORMATION
Emission Control System Information
The U.S. and California Clean Air Acts
Tampering and Altering
Source of Emissions
The combustion process produces carbon monoxide, oxides ofnitrogen, and hydrocarbons. Control of hydrocarbons and oxides ofnitrogen is very important because, under certain conditions, theyreact to form photochemical smog when subjected to sunlight. Carbonmonoxide does not react in the same way, but it is toxic.
Honda utilizes lean carburetor settings and other systems to reducethe emissions of carbon monoxide, oxides of nitrogen andhydrocarbons.
EPA and California regulations require all manufacturers to furnishwritten instructions describing the operation and maintenance of emis-sion control systems.
The following instructions and procedures must be followed in orderto keep the emissions from your Honda engine within the emissionstandards.
Tampering with or altering the emission control system may increaseemissions beyond the legal limit. Among those acts that constitutetampering are:
Removal or alteration of any part of the intake, fuel or exhaustsystems.
Altering or defeating the governor linkage or speed-adjustingmechanism to cause the engine to operate outside its designparameters.
07/05/29 13:27:46 31YG0600_053
53
TECHNICAL & CONSUMER INFORMATION
Problems That May Affect Emissions
Replacement Parts
Maintenance
If you are aware of any of the following symptoms, have your engineinspected and repaired by your servicing dealer.
Hard starting or stalling after starting.
Rough idle.
Misfiring or backfiring under load.
Afterburning (backfiring).
Black exhaust smoke or high fuel consumption.
The emission control systems on your Honda engine were designed,built, and certified to conform with EPA and California emissionregulations. We recommend the use of genuine Honda partswhenever you have maintenance done. These original-designreplacement parts are manufactured to the same standards as theoriginal parts, so you can be confident of their performance. The useof replacement parts that are not of the original design and qualitymay impair the effectiveness of your emission control system.
A manufacturer of an aftermarket part assumes the responsibility thatthe part will not adversely affect emission performance. Themanufacturer or rebuilder of the part must certify that use of the partwill not result in a failure of the engine to comply with emissionregulations.
Follow the maintenance schedule (see page ). Remember that thisschedule is based on the assumption that your machine will be usedfor its designed purpose. Sustained high-load or high-temperatureoperation, or use in unusually wet or dusty conditions, will requiremore frequent service.
26
07/05/29 13:27:53 31YG0600_054
+-
× ×
--
±±
×
54
TECHNICAL & CONSUMER INFORMATION
Specifications
Dimensions and weight
Engine design and performance
Tune up
Pump
WT20X
24.4 in (620 mm)18.1 in (460 mm)18.3 in (465 mm)
GX160K14-stroke, overhead valve, single cylinder
104 lbs (47 kg)
Forced airTransistor magnetoCounterclockwise
1,400 rpm
9.9 cu-in (163 cm )[2.68 1.77 in (68.0 45.0 mm)]
Spark plug gap
Idle speedValve clearance(cold)Other specifications
0.028 0.031 in(0.70 0.80 mm)
0.20 0.02 mm0.15 0.02 mm
No other adjustments needed.
Suction port diameterDischarge port diameterTotal head (maximum)Suction head (maximum)Discharge capacity (maximum)
Self-priming timeContinuous running time
2.0 in (50 mm)2.0 in (50 mm)98.4 ft (30 m)26.2 ft (8 m)187.6 US gal (710 )
60 seconds at 14.8 ft (4.5 m)Approximately 2.1 hours (actualtime varies with pump load)
LengthWidthHeightDry mass [weight]
ModelEngine typeDisplacement[bore stroke]Fuel tank capacityEngine oil capacityCooling systemIgnition systemPTO shaft rotation
0.82 US gal (3.1 )0.63 US qt (0.60 )
Intake:Exhaust:
per minute
See page 35.
See shopmanual.
200150
07/05/29 13:28:12 31YG0600_055
×
±±
× ×
--±
55
TECHNICAL & CONSUMER INFORMATION
Dimensions and weight
Engine design and performance
Tune up
Pump
WT30X
LengthWidthHeightDry mass [weight]
ModelEngine typeDisplacement[bore stroke]Fuel tank capacityEngine oil capacityCooling systemIgnition systemPTO shaft rotation
Spark plug gap
Idle speedValve clearance(cold)Other specifications
0.15 0.02 mm0.20 0.02 mm
No other adjustments needed.
26.0 in (660 mm)19.5 in (495 mm)20.3 in (515 mm)132 lbs (60 kg)
GX240K14-stroke, overhead valve, single cylinder14.8 cu-in (242 cm )[2.87 2.28 in (73.0 58.0 mm)]
Forced airTransistor magnetoCounterclockwise
0.028 0.031 in(0.70 0.80 mm)1,400 150 rpm
3.1 in (80 mm)3.1 in (80 mm)88.6 ft (27 m)26.2 ft (8 m)319.7 US gal (1,210 )
90 seconds at 14.8 ft (4.5 m)Approximately 2.3 hours (actualtime varies with pump load)
Suction port diameterDischarge port diameterTotal head (maximum)Suction head (maximum)Discharge capacity (maximum)
Self-priming timeContinuous running time
1.40 US gal (5.3 )1.2 US qt (1.1 )
Intake:Exhaust:
per minute
See page 35.
See shopmanual.
07/05/29 13:28:29 31YG0600_056
±±±
× ×
--
×
56
TECHNICAL & CONSUMER INFORMATION
Dimensions and weight
Engine design and performance
Tune up
Pump
WT40X
Spark plug gap
Idle speedValve clearance(cold)Other specifications
1,400 150 rpm0.15 0.02 mm0.20 0.02 mm
No other adjustments needed.
28.9 in (735 mm)21.1 in (535 mm)22.2 in (565 mm)172 lbs (78 kg)
GX340K14-stroke, overhead valve, single cylinder20.6 cu-in (338 cm )[3.23 2.52 in (82.0 64.0 mm)]
Forced airTransistor magnetoCounterclockwise
0.028 0.031 in(0.70 0.80 mm)
3.9 in (100 mm)3.9 in (100 mm)85.3 ft (26 m)26.2 ft (8 m)433.3 US gal (1,640 )
150 seconds at 14.8 ft (4.5 m)Approximately 1.6 hours (actualtime varies with pump load)
Suction port diameterDischarge port diameterTotal head (maximum)Suction head (maximum)Discharge capacity (maximum)
Self-priming timeContinuous running time
LengthWidthHeightDry mass [weight]
ModelEngine typeDisplacement[bore stroke]Fuel tank capacityEngine oil capacityCooling systemIgnition systemPTO shaft rotation
1.2 US qt (1.1 )1.61 US gal (6.1 )
Intake:Exhaust:
per minute
See page 35.
See shopmanual.
07/05/29 13:28:47 31YG0600_057
57
TECHNICAL & CONSUMER INFORMATION
CONSUMER INFORMATION
Honda Publications
Shop Manual
Parts Catalog
These publications will give you additional information formaintaining and repairing your pump. You may order them from yourHonda pump dealer.
This manual covers complete maintenance and overhaul procedures.It is intended to be used by a skilled technician.
This manual provides complete, illustrated parts lists.
09/03/26 10:13:55 31YG0600_058
58
TECHNICAL & CONSUMER INFORMATION
Customer Service Information
Servicing dealership personnel are trained professionals. They shouldbe able to answer any question you may have. If you encounter aproblem that your dealer does not solve to your satisfaction, pleasediscuss it with the dealership’s management. The Service Manager orGeneral Manager can help. Almost all problems are solved in this way.
If you are dissatisfied with the decision made by the dealership’smanagement, contact the Honda Power Equipment CustomerRelations Office. You can write to:
Or telephone: (770)497-6400
American Honda Motor Co., Inc.Power Equipment DivisionCustomer Relations Office4900 Marconi DriveAlpharetta, Georgia 30005-8847
When you write or call, please give us this information:
Model and serial number (see page )
Name of the dealer who sold the pump to you
Name and address of the dealer who services your pump
Date of purchase
Your name, address and telephone number
A detailed description of the problem
50
09/03/26 10:14:02 31YG0600_059
59
MEMO
07/05/29 13:28:49 31YG0600_060
60
MEMO
07/05/29 13:28:51 31YG0600_061
- -
QUICK REFERENCE INFORMATION
Unleaded gasoline with a pumpoctane rating of 86 or higher(page 28 )SAE 10W-30, API SJ or later (orequivalent), for general use(page 31 )
Check engine oil level.Check air filter.Change engine oil.
Refer to the maintenanceschedule on page 26 .
0.028 0.031 in (0.70 0.80 mm)W20EPR-U
BPR6ES
Fuel
Engine Oil
Spark Plug
Maintenance
Type
Type
Type
Gap
Before eachuseFirst20 hoursSubsequent
NGK:DENSO:
(page 35 )
07/05/29 13:28:57 31YG0600_062
WT20X-40取説表紙31YG0602
C 2002-2009 Honda Motor Co., Ltd. -All Rights Reserved
Owner,s Manual
WATER PUMPWT20X・WT30X・WT40X
Printed in Japan英 NAH HC
HiEM3
DIC F101(PF) BK
K2:WT40XK3:WT20X, WT30X
31YG060300X31-YG0-6030
2000.2009.03