www.ti.com
FEATURES
1
2
3
4
8
7
6
5
OFFSET N1
IN-
IN+
VCC-
OFFSET N2
VCC+
OUT
NC
D PACKAGE(TOP VIEW)
DESCRIPTION
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
– VIO . . . 100 μV Max• Controlled Baseline – AVD . . . 45 V/μV Typ With RL = 2 kΩ,
19 V/μV Typ With RL = 600 Ω– One Assembly/Test Site, One FabricationSite • Available in Standard-Pinout Small-Outline
Package• Extended Temperature Performance of–55°C to 125°C • Output Features Saturation Recovery Circuitry
• Enhanced Diminishing Manufacturing Sources • Macromodels and Statistical information(DMS) Support
• Enhanced Product-Change Notification• Qualification Pedigree(1)
• Outstanding Combination of DC Precision andAC Performance:– Unity-Gain Bandwidth . . . 13 MHz Typ– Vn . . . 3.3 nV/√Hz at f = 10 Hz Typ,
2.5 nV/√Hz at f = 1 kHz Typ(1) Component qualification in accordance with JEDEC and
industry standards to ensure reliable operation over anextended temperature range. This includes, but is not limitedto, Highly Accelerated Stress Test (HAST) or biased 85/85,temperature cycle, autoclave or unbiased HAST,electromigration, bond intermetallic life, and mold compoundlife. Such qualification testing should not be viewed asjustifying use of this component beyond specifiedperformance and environmental limits.
The TLE2027 contains innovative circuit design expertise and high-quality process control techniques to producea level of ac performance and dc precision previously unavailable in single operational amplifiers. Manufacturedusing TI's state-of-the-art Excalibur process, these devices allow upgrades to systems that use lower-precisiondevices.
In the area of dc precision, the TLE2027 offers maximum offset voltages of 100 μV, common-mode rejectionratio of 131 dB (typ), supply voltage rejection ratio of 144 dB (typ), and dc gain of 45 V/μV (typ).
The ac performance of the TLE2027 is highlighted by a typical unity-gain bandwidth specification of 15 MHz, 55°of phase margin, and noise voltage specifications of 3.3 nV/√Hz and 2.5 nV/√Hz at frequencies of 10 Hz and1 kHz, respectively.
The TLE2027 is available in a wide variety of packages, including the industry-standard 8-pin small-outlineversion for high-density system applications. The device is characterized for operation over the full militarytemperature range of –55°C to 125°C.
ORDERING INFORMATION (1)
PACKAGED DEVICESVIOmax ATTA 25°C SMALL OUTLINE (2) (D)
–55°C to 125°C 100 μV TLE2027MDREP
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TIwebsite at www.ti.com.
(2) The D package is available taped and reeled with 2500 units/reel.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2007, Texas Instruments IncorporatedProducts conform to specifications per the terms of the TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.
www.ti.com
OUT
OFFSET N2
IN-
IN+
OFFSET N1
-
+
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
SYMBOL
2 Submit Documentation Feedback
www.ti.com
TLE202XY CHIP INFORMATION
BONDING PAD ASSIGNMENTS
Chip Thickness: 15 MiIs Typical
Bonding Pads: 4 4 Mils Minimum´
T max = 150 CJ °
Tolerances Are 10%.±
All Dimensions Are in Mils.
Pin (4) is Internally Connectedto Backside of Chip.
(1) (2) (3)
(4)
(5)
(6)(7)(8)
90
73
(1)
(2)
(3)
(4)(6)
(7)
(8)
+
-
OUT
IN +
IN-
VCC+
VCC-
OFFSET N1
OFFSET N2
(1)
(3)
(2)
(8)
(7)
(4)
(6)
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
This chip, when properly assembled, displays characteristics similar to the TLE202xC. Thermal compression orultrasonic bonding may be used on the doped-aluminum bonding pads. The chip may be mounted withconductive epoxy or a gold-silicon preform.
3Submit Documentation Feedback
www.ti.com
R2
4R
26
Q5
7
Q5
6
Q5
5
Q6
0
OU
T
Q6
2
Q5
9
Q6
1Q
58
R2
5
Q4
8
Q5
4
Q5
3Q5
2
Q4
9
Q5
0
R2
3
R2
2
R2
1
R2
0
Q4
6
Q4
2
R1
9
Q4
7
Q4
4
Q4
3
Q4
0
Q4
5
Q4
1
Q3
9
Q3
8
Q3
7
Q3
5
R1
5
Q3
6
R1
6
R1
7
C4
C3
R1
3
Q3
4
Q3
3
Q3
2
R9
Q2
7
Q3
0
R8
R1
1
Q2
5Q
28
C2
Q3
1
Q2
6Q
29
R1
8R
14
R1
2R
10
R7
Q1
9
C1
Q2
4Q
23
Q2
0
R6
R3
Q2
1
Q2
2
Q1
6
Q1
5
Q1
8
R5
R4
Q1
3
Q1
4
Q1
7
R2
R1
OF
FS
ET
N2
OF
FS
ET
N1
Q1
2
Q1
0
Q9
Q1
1
Q8
Q7
Q5
Q6
Q4
Q1Q
3
Q2
Q5
1
CC
V
CC
+V
-
IN+ IN*
AC
TU
AL
DE
VIC
E C
OM
PO
NE
NT
CO
UN
T
Tra
nsis
tors
Re
sis
tors
ep
iFE
T
Ca
pa
cito
rs
61
26 1 4
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
EQUIVALENT SCHEMATIC
4 Submit Documentation Feedback
www.ti.com
Absolute Maximum Ratings (1)
Dissipation Rating Table
Recommended Operating Conditions
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
VCC+ Supply voltage (2) 19 V
VCC– Supply voltage –19 V
VID Differential input voltage (3) ±1.2 V
VI Input voltage range (any input) VCC±
II Input current (each input) ±1 mA
IO Output current ±50 mA
Total current into VCC+ 50 mA
Total current out of VCC– 50 mA
Duration of short-circuit current at (or below) 25°C (4) Unlimited
See DissipationContinuous total power dissipation Rating Table
TA Operating free-air temperature range –55 125 °C
Tstg Storage temperature range (5) –65 150 °C
Lead temperature 1,6 mm (1/16 in) from case for 10 s D package 260 °C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operatingconditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC– .(3) Differential voltages are at IN+ with respect to IN–. Excessive current flows if a differential input voltage in excess of approximately
±1.2 V is applied between the inputs, unless some limiting resistance is used.(4) The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation
rating is not exceeded.(5) Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of
overall device life. See http://www.ti.com/ep_quality for additional information on enhanced product packaging.
TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 105°C TA = 125°CPACKAGE POWER RATING ABOVE TA = 25°C POWER RATING POWER RATING POWER RATING
D 725 mW 5.8 mW/°C 464 mW 261 mW 145 mW
MIN MAX UNIT
VCC± Supply voltage ±4 ±19 V
TA = 25°C –11 11VIC Common-mode input voltage V
TA = Full range (1) –10.3 10.3
TA Operating free-air temperature –55 125 °C
(1) Full range is –55°C to 125°C.
5Submit Documentation Feedback
www.ti.com
Electrical Characteristics
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
at specified free-air temperature, VCC± = ±15 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TA(1) MIN TYP MAX UNIT
25°C 20 100VIO Input offset voltage VIC = 0, RS = 50 Ω μV
Full range 200
αVIO Temperature coefficient of input offset voltage VIC = 0, RS = 50 Ω Full range 0.4 μV/°C
Input offset voltage long-term drift (2) VIC = 0, RS = 50 Ω 25°C 0.006 μV/mo
25°C 6 90IIO Input offset current VIC = 0, RS = 50 Ω nA
Full range 150
25°C 15 90IIB Input bias current VIC = 0, RS = 50 Ω nA
Full range 150
–11 –1325°C to to
11 13VICR Common-mode input voltage range RS = 50 Ω V
–10.3Full range to
10.3
25°C 10.5 12.9RL = 600 Ω
Full range 10VOM+ Maximum positive peak output voltage swing V
25°C 12 13.2RL = 2 kΩ
Full range 11
25°C –10.5 –13RL = 600 Ω
Full range –10VOM– Maximum negative peak output voltage swing V
25°C –12 –13.5RL = 2 kΩ
Full range –11
VO = ±11 V, RL = 2 kΩ 25°C 5 45
VO = ±10 V, RL = 2 kΩ Full range 2.5
AVD Large-signal differential voltage amplification 25°C 3.5 38 V/μVVO = ±10 V, RL = 1 kΩ
Full range 1.8
VO = ±10 V, RL = 600 Ω 25°C 2 19
Ci Input capacitance 25°C 8 pF
zo Open-loop output impedance IO = 0 25°C 50 Ω
25°C 100 131VIC = VICRmin,CMRR Common-mode rejection ratio dBRS = 50 Ω Full range 96
VCC± = ±4 V to ±18 V, 25°C 94 144RS = 50 ΩkSVR Supply-voltage rejection ratio (ΔVCC±/ΔVIO) dB
VCC± = ±4 V to ±18 V, Full range 90RS = 50 Ω
25°C 3.8 5.3ICC Supply current VO = 0, No load mA
Full range 5.6
(1) Full range is –55°C to 125°C.(2) Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to
TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
6 Submit Documentation Feedback
www.ti.com
Operating Characteristics
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
at specified free-air temperature, VCC± = ±15 V, TA = 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
RL = 2 kΩ, CL = 100 pF, 1.7 2.8See Figure 1SR Slew rate at unity gain V/μsRL = 2 kΩ, CL = 100 pF,
TA = –55°C to 125°C, 1See Figure 1
f = 10 Hz 3.3Vn Equivalent input noise voltage (see Figure 2) RS = 20 Ω nV/√Hz
f = 1 kHz 2.5
VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 50 nV
f = 10 Hz 1.5In Equivalent input noise current pA/√Hz
f = 1 kHz 0.4
THD Total harmonic distortion VO = 10 V, AVD = 1 (1) <0.002%
B1 Unity-gain bandwidth (see Figure 3) RL = 2 kΩ, CL = 100 pF 13 MHz
BOM Maximum output-swing bandwidth RL = 2 kΩ 30 kHz
φm Phase margin at unity gain (see Figure 3) RL = 2 kΩ, CL = 100 pF 55°
(1) Measured distortion of the source used in the analysis was 0.002%.
7Submit Documentation Feedback
www.ti.com
PARAMETER MEASUREMENT INFORMATION
VO
20 W20 W
2 kW
-15 V
15 V
+
-
R = 2 kL WC =L
100 pF
(see Note A)
VO
-15 V
VI +
-
15 V
Rf
NOTE A: C includes fixture capacitance.L
RI
VO
2 kWC =L
100 pF
(see Note A)
10 kW
100 W
VI
-15 V
15 V
+
-
NOTE A: C includes fixture capacitance.L
VO
2 kW-15 V
15 V
-
+VIC =L
100 pF
(see Note A)
NOTE A: C includes fixture capacitance.L
Rf
RI
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
Figure 1. Slew-Rate Test Circuit Figure 2. Noise-Voltage Test Circuit
Figure 3. Unity-Gain Bandwidth and Figure 4. Small-Signal Pulse-Response Test CircuitPhase-Margin Test Circuit
8 Submit Documentation Feedback
www.ti.com
DEVICE INFORMATION
Typical Values
Initial Estimates of Parameter Distributions
− S
uppl
y C
urre
nt −
mA
CC
I
4.5
5
4
3.5
3
2.5
TA − Free-Air T emperature − °C
1501251007550250−25−50−75
(5% of the devices fell below this point)5% point on the distribution bar
and lower points on the distribution bar .90% of the devices were within the upper
(5% of the devices fell above this point)95% point on the distribution bar
SUPPLY CURRENTvs
FREE-AIR TEMPERATUREÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 V
VO = 0No LoadSample Size = 835 UnitsFrom 2 Water Lots
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
Typical values presented in this data sheet represent the median (50% point) of device parametric performance.
In the ongoing program of improving data sheets and supplying more information to our customers, TexasInstruments has added an estimate of not only the typical values but also the spread around these values.These are in the form of distribution bars that show the 95% (upper) points and the 5% (lower) points from thecharacterization of the initial wafer lots of this new device type (see Figure 5). The distribution bars are shown atthe points where data was actually collected. The 95% and 5% points are used instead of ±3 sigma since someof the distributions are not true Gaussian distributions.
The number of units tested and the number of different wafer lots used are on all of the graphs wheredistribution bars are shown. As noted in Figure 5, there were a total of 835 units from two wafer lots. In thiscase, there is a good estimate for the within-lot variability and a possibly poor estimate of the lot-to-lot variability.This is always the case on newly released products since there can only be data available from a few wafer lots.
The distribution bars are not intended to replace the minimum and maximum limits in the electrical tables. Eachdistribution bar represents 90% of the total units tested at a specific temperature. While 10% of the units testedfell outside any given distribution bar, this should not be interpreted to mean that the same individual devices felloutside every distribution bar.
Figure 5. Sample Graph With Distribution Bars
9Submit Documentation Feedback
www.ti.com
TYPICAL CHARACTERISTICS
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
Table of Graphs
FIGURE
VIO Input offset voltage Distribution 6,
ΔVIO Input offset voltage change vs Time after power on 7, 8
IIO Input offset current vs Free-air temperature 9
vs Free-air temperature 10IIB Input bias current
vs Common-mode input voltage 11
II Input current vs Differential input voltage 12
VO(PP) Maximum peak-to-peak output voltage vs Frequency 13, 14
vs Load resistance 15, 16VOM Maximum (positive/negative) peak output voltage
vs Free-air temperature 17, 18
vs Supply voltage 19
vs Load resistance 20AVD Large-signal differential voltage amplification
vs Frequency 21, 22
vs Free-air temperature 23
zo Output impedance vs Frequency 24
CMRR Common-mode rejection ratio vs Frequency 25
kSVR Supply-voltage rejection ratio vs Frequency 26
vs Supply voltage 27, 28
IOS Short-circuit output current vs Elapsed time 29, 30
vs Free-air temperature 31, 32
vs Supply voltage 33ICC Supply current
vs Free-air temperature 34
Small signal 35Voltage-follower pulse response
Large signal 36
Vn Equivalent input noise voltage vs Frequency 37
Noise voltage (referred to input) Over 10-s interval 38
vs Supply voltage 39B1 Unity-gain bandwidth
vs Load capacitance 40
SR Slew rate vs Free-air temperature 41
vs Supply voltage 42
φm Phase margin vs Loadcapacitance 43
vs Free-air temperature 44
10 Submit Documentation Feedback
www.ti.com
TYPICAL CHARACTERISTICS
INPUT OFFSET VOLTAGE CHANGEvs
TIME AFTER POWER ON
00
t − Time After Power On − s10 20 30 40 50 60
2
4
6
8
10
12 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁAV
IO −
Cha
nge
in In
put O
ffset
Vol
tage
− ÁÁÁÁÁÁÁÁÁÁ∆V IO
µV ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ50 Amplifiers T ested From 2 W afer Lots
VCC± = ±15 VTA = 25°C
ÎÎÎÎÎÎÎÎÎÎÎÎD Package
Per
cent
age
of
Am
plifi
ers
− %
VIO − Input Offset V oltage − µV
TA = 25°CVCC = 15 V
16
14
12
10
8
6
4
2
0 120906030− 30− 60− 90− 1200
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎD Package
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ1568 Amplifiers T ested From 2 W afer Lots
DISTRIBUTIONINPUT OFFSET VOLTAGE
t − Time After Power On − s
INPUT OFFSET VOLTAGE CHANGEvs
TIME AFTER POWER ON6
5
4
3
2
1
00 20 40 60 80 100 120 140 160 180
AV
IO −
Cha
nge
in In
put O
ffset
Vol
tage
− ÁÁÁÁÁÁÁÁÁÁ∆V IO
µV ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ50 Amplifiers T ested From 2 W afer Lots
VCC± = ±15 VTA = 25°C
ÎÎÎÎÎÎÎÎÎÎÎÎP Package
0
IIO −
Inpu
t Offs
et C
urre
nt −
nA
5
10
15
20
25
30
1501251007550250− 25− 50
TA − Free-Air T emperature − °C
− 75
INPUT OFFSET CURRENTvs
FREE-AIR TEMPERATURE
IOI
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VVIC = 0Sample Size = 833 UnitsFrom 2 Wafer Lots
NOTE A: Data at high and low temperatures areapplicable only within the rated operatingfree-air temperature ranges of the variousdevices.
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
Figure 6. Figure 7.
Figure 8. Figure 9.
11Submit Documentation Feedback
www.ti.com
INPUT BIAS CURRENTvs
COMMON-MODE INPUT VOLTAGE
0−12
VIC − Common-Mode Input V oltage − V− 8 − 4 0 4 8 12
5
10
15
20
25
30
35
40
TA = 25°CVCC± = ±15 V
IIB −
Inpu
t Bia
s C
urre
nt −
nA
IBI
INPUT BIAS CURRENTvs
FREE-AIR TEMPERATURE
−20−75
IIB −
Inpu
t Bia
s C
urre
nt −
nA
TA − Free-Air T emperature − °C
−10
0
10
20
30
40
50
60
−50 −25 0 25 50 75 100 125 150
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VVIC = 0Sample Size = 836 UnitsFrom 2 Wafer Lots
IBI
NOTE A: Data at high and low temperatures are applicableonly within the rated operating free-airtemperature ranges of the various devices.
II −
Inpu
t Cur
rent
− m
A
−1−1.8
VID − Differential Input V oltage − V
−0.8
−0.6
−0.4
−0.2
0
0.2
0.4
0.6
0.8
1
−1.2 −0.6 0 0.6 1.2 1.8
INPUT CURRENTvs
DIFFERENTIAL INPUT VOLTAGE
II
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VVIC = 0TA = 25°C
VO
(PP
)−
Max
imum
Pea
k-to
-Pea
k O
utpu
t Vol
tage
− V
TA = −55°C
TA = 125°C
10 M1 M100 k
30
25
20
15
10
5
f − Frequency − Hz
10 k0
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 VRL = 2 kΩ
MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE
vsFREQUENCY
NOTE A: Data at high and low temperatures are applicable onlywithin the rated operating free-air temperature ranges ofthe various devices.
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 10. Figure 11.
Figure 12. Figure 13.
12 Submit Documentation Feedback
www.ti.com
MAXIMUM POSITIVE PEAKOUTPUT VOLTAGE
vsLOAD RESISTANCE
0100V
OM
+ −
Max
imum
Pos
itive
Pea
k O
utpu
t Vol
tage
− V
RL − Load Resistance − Ω
2
4
6
8
10
12
14
1 k 10 k
ÁÁÁÁÁÁÁÁÁÁV OM+ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VTA = 25°C
VO
(PP
) − M
axim
um P
eak-
to-P
eak
Out
put V
olta
ge −
V
010 k
f − Frequency − Hz
5
10
15
20
25
30
100 k 1 M 100 M
TA = −55°C
10 M
ÁÁÁÁÁÁÁÁÁÁV O(PP)ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏRL = 2 kΩ
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 VÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏTA = 125°C
TLE2037MAXIMUM PEAK-TO-PEAK
OUTPUT VOLTAGEvs
FREQUENCY
NOTE A: Data at high and low temperatures are applicableonly within the rated operating free-air temperatureranges of the various devices.
0100V
OM
− −
Max
imum
Neg
ativ
e P
eak
Out
put V
olta
ge −
V
RL − Load Resistance − Ω
−2
−4
−6
−8
−10
−12
−14
1 k 10 k
MAXIMUM NEGATIVE PEAKOUTPUT VOLTAGE
vsLOAD RESISTANCE
ÁÁÁÁÁÁÁÁÁÁV OM− ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VTA = 25°C
MAXIMUM POSITIVE PEAKOUTPUT VOLTAGE
vsFREE-AIR TEMPERATURE
12.9−75
TA − Free-Air T emperature − °C
13
13.1
13.2
13.3
13.4
13.5
−25 0 25 50 75 100 125 150VO
M+
− M
axim
um P
ositi
ve P
eak
Out
put V
olta
ge −
V
ÁÁÁÁÁÁÁÁÁÁV OM+ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 VÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏRL = 2 kΩÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏFrom 2 Wafer Lots
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏSample Size = 832 Units
−50
NOTE A: Data at high and low temperatures are applicableonly within the rated operating free-airtemperature ranges of the various devices.
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 14. Figure 15.
Figure 16. Figure 17.
13Submit Documentation Feedback
www.ti.com
LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICA TION
vsSUPPLY VOLTAGE
00
VCC± − Supply V oltage − V
50
4 8 12 16 20
10
20
30
40RL = 2 kΩ
RL = 1 kΩ
RL = 600 Ω
ÏÏÏÏÏÏÏÏÏÏÏÏTA = 25°C
AV
D −
Lar
ge-S
igna
l diff
eren
tialÁÁÁÁÁÁÁÁÁÁA VD
Vµ
V/
Vol
tage
Am
plifi
catio
n −
MAXIMUM NEGATIVE PEAKOUTPUT VOLTAGE
vsFREE-AIR TEMPERATURE
−14−75
TA − Free-Air T emperature − °C
−13.8
−13.6
−13.4
−13.2
−13
−50 −25 0 25 50 75 100 125 150
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎRL = 2 kΩ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVCC± = ±15 V
VO
M−
− M
axim
um N
egat
ive
Pea
k O
utpu
t Vol
tage
− V
ÁÁÁÁÁÁÁÁÁÁV OM
−
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSample Size = 831 Units
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎFrom 2 Wafer Lots
NOTE A: Data at high and low temperatures are applicableonly within the rated operating free-air temperatureranges of the various devices.
AVD
Phase Shift
VCC± = ±15 VRL = 2 kΩCL = 100 pFTA = 25°C
Pha
se S
hift
275°
75°
250°
225°
200°
175°
150°
125°
100°140
120
100
80
60
40
20
100 k100
160
100 Mf − Frequency − Hz
00.1
AV
D −
Lar
ge-S
igna
l Diff
eren
tialÁÁÁÁÁÁÁÁÁÁA VD V
olta
ge A
mpl
ifica
tion
− dB
LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICA TION AND PHASE SHIFT
vsFREQUENCY
10
0
50
100 200 400 1 k 4 k 10 k2 k
40
30
20
RL − Load Resistance − Ω
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁTA = 25°CVCC± = ±15 V
AV
D −
Lar
ge-S
igna
l diff
eren
tialÁÁÁÁÁÁÁÁÁÁA VD
Vµ
V/
Vol
tage
Am
plifi
catio
n −
LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION
vsLOAD RESISTANCE
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 18. Figure 19.
Figure 20. Figure 21.
14 Submit Documentation Feedback
www.ti.com
300°
100°
275°
250°
225°
200°
175°
150°
125°
Pha
se S
hiftAVD
Phase Shift
704020
3
0
−3
−6
−9
−12
−15
6
100
f − Frequency − MHz
−1810
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVCC± = ±15 VRL = 2 kΩCL = 100 pFTA = 25°C
AV
D −
Lar
ge-S
igna
l Diff
eren
tialÁÁÁÁÁÁÁÁÁÁA VD V
olta
ge A
mpl
ifica
tion
− dB
LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICA TION AND PHASE SHIFT
vsFREQUENCY
−7530
TA − Free-Air T emperature − °C150
60
−50 −25 0 25 50 75 100 125
40
50
VCC± = ±15 V ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏRL = 2 kΩÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏRL = 1 kΩ
LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION
vsFREE-AIR TEMPERATURE
AV
D −
Lar
ge-S
igna
l diff
eren
tialÁÁÁÁÁÁÁÁÁÁA VD
Vµ
V/
Vol
tage
Am
plifi
catio
n −
NOTE A: Data at high and low temperatures are applicable onlywithin the rated operating free-air temperature rangesof the various devices.
100
CM
RR
− C
omm
on-M
ode
Rej
ectio
n R
atio
− d
B
f − Frequency − Hz100 M
140
100 1 k 10 k 100 k 1 M 10 M
20
40
60
80
100
120
COMMON-MODE REJECTION RATIOvs
FREQUENCYÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÏÏÏÏÏÏÏÏÏÏÏÏTA = 25°C
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 V
OUTPUT IMPEDANCEvs
FREQUENCY
10−100
zo −
Out
put I
mpe
danc
e −
f − Frequency − Hz
100 M
100
100 1 k 10 k 100 k 1 M 10 M
−10
1
10
AVD = 100
See Note A
AVD = 10ÁÁÁÁÁÁÁÁz o
ÁÁÁÁÁÁÁÁΩ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VTA = 25°C
NOTE A: For this curve, AVD = 1
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 22. Figure 23.
Figure 24. Figure 25.
15Submit Documentation Feedback
www.ti.com
0−30
IOS
− S
hort-
Circ
uit O
utpu
t Cur
rent
− m
A
−42
2 4 6 8 10 12 14 16 18 20
−32
−34
−36
−38
−40
SHORT-CIRCUIT OUTPUT CURRENTvs
SUPPLY VOLTAGE
VCC± − Supply V oltage − V
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVID = 100 mVVO = 0TA = 25°C
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏP PackageÁÁÁÁÁÁÁÁOS
I10
0
− S
uppl
y-V
olta
ge R
ejec
tion
Rat
io −
dB
f − Frequency − Hz100 M
140
100 1 k 10 k 100 k 1 M 10 M
20
40
60
80
100
120 ÏÏÏÏÏÏÏÏÏkSVR−ÏÏÏÏÏÏÏÏÏÏÏÏkSVR+
SUPPLY-VOLTAGE REJECTION RATIOvs
FREQUENCYÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÏÏÏÏÏÏÏÏÏÏÏÏTA = 25°C
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 V
SV
RK
SHORT-CIRCUIT OUTPUT CURRENTvs
SUPPLY VOLTAGE
030
44
2 4 6 8 10 12 14 16 18 20
32
34
36
38
40
42
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVID = −100 mVVO = 0TA = 25°CP Package
IOS
− S
hort-
Circ
uit O
utpu
t Cur
rent
− m
AÁÁÁÁÁÁÁÁOS
I
VCC± − Supply V oltage − V0
−35
t − Elapsed T ime − s180
−45
30 60 90 120 150
−37
−39
−41
−43
SHORT-CIRCUIT OUTPUT CURRENTvs
ELAPSED TIMEÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏP Package
TA = 25°CVO = 0VID = 100 mV
VCC± = ±15 V
IOS
− S
hort-
Circ
uit O
utpu
t Cur
rent
− m
AÁÁÁÁÁÁÁÁOS
I
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 26. Figure 27.
Figure 28. Figure 29.
16 Submit Documentation Feedback
www.ti.com
SHORT-CIRCUIT OUTPUT CURRENTvs
ELAPSED TIME
034
t − Elapsed T ime − s180
44
30 60 90 120 150
36
38
40
42
IOS
− S
hort-
Circ
uit O
utpu
t Cur
rent
− m
AÁÁÁÁÁÁÁÁOS
I
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏP PackageTA = 25°CVO = 0VID = 100 mV
VCC ± = ±15 V
−75−24
TA − Free-Air T emperature − °C150
−48
−50 −25 0 25 50 75 100 125
−28
−32
−36
−40
−44
SHORT-CIRCUIT OUTPUT CURRENTvs
FREE-AIR TEMPERATURE
IOS
− S
hort-
Circ
uit O
utpu
t Cur
rent
− m
AÁÁÁÁÁÁÁÁOS
I
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VVID = 100 mVVO = 0P Package
NOTE A: Data at high and low temperatures are applicable onlywithin the rated operating free-air temperature rangesof the various devices.
26
TA − Free-Air T emperature − °C
46
30
34
38
42
1251007550250−25−50 150−75
SHORT-CIRCUIT OUTPUT CURRENTvs
FREE-AIR TEMPERATURE
IOS
− S
hort-
Circ
uit O
utpu
t Cur
rent
− m
AÁÁÁÁÁÁÁÁOS
I
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VVID = −100 mVVO = 0P Package
NOTE A: Data at high and low temperatures are applicable onlywithin the rated operating free-air temperature rangesof the various devices.
ÁÁÁÁÁÁÁÁÁÁÁÁ0
0
ICC
− S
uppl
y C
urre
nt −
mA
VCC± − Supply V oltage − V
6
2 4 6 8 10 12 14 16 18 20
1
2
3
4
5
SUPPLY CURRENTvs
SUPPLY VOLTAGEÁÁÁÁÁÁÁÁCC
I
VO = 0No Load
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏTA = 125°CÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏTA = 25°CÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏTA = −55°C
NOTE A: Data at high and low temperatures are applicableonly within the rated operating free-air temperatureranges of the various devices.
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 30. Figure 31.
Figure 32. Figure 33.
17Submit Documentation Feedback
www.ti.com
VO
− O
utpu
t Vol
tage
− m
V 50
0
−50
8006004002000
100
1000t − Time − ns
−100
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 VRL = 2 kΩCL = 100 pFTA = 25°CSee Figure 4
VOLTAGE-FOLLOWERSMALL-SIGNAL
PULSE RESPONSE
−752.5
TA − Free-Air T emperature − °C150
5
−50 −25 0 25 50 75 100 125
3
3.5
4
4.5
SUPPLY CURRENTvs
FREE-AIR TEMPERATURE
ICC
− S
uppl
y C
urre
nt −
mAÁÁÁÁÁÁÁÁC
CI
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 VVO = 0No LoadSample Size = 836 UnitsFrom 2 Wafer Lots
NOTE A: Data at high and low temperatures are applicableonly within the rated operating free-air temperatureranges of the various devices.
10
Vn
− E
quiv
alen
t Inp
ut N
oise
Vol
tage
− n
VH
z
f − Frequency − Hz
100 k
10
10 100 1 k 10 k
2
4
6
8
EQUIVALENT INPUT NOISE VOLTAGEvs
FREQUENCYÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 V
RS = 20 ΩTA = 25°CSee Figure 2Sample Size = 100 UnitsFrom 2 Wafer Lots
Vn
ÁÁÁÁÁÁÁÁÁÁÁÁnV/Hz
t − Time − µs250 5 10 15 20
10
5
0
−5
−10
15
−15
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 VRL = 2 kΩCL = 100 pFTA = 25°CSee Figure 1
VO
− O
utpu
t Vol
tage
− V
VOLTAGE-FOLLOWERLARGE-SIGNAL
PULSE RESPONSE
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 34. Figure 35.
Figure 36. Figure 37.
18 Submit Documentation Feedback
www.ti.com
NOISE VOLTAGE(REFERRED TO INPUT)OVER A 10-S INTERVAL
0−50
Noi
se V
olta
ge −
nV
t − Time − s
10
50
2 4 6 8
−40
−30
−20
−10
0
10
20
30
40
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁVCC± = ±15 V
f = 0.1 to 10 HzTA = 25°C
20
B1
− U
nity
-Gai
n B
andw
idth
− M
Hz
18
16
14
12
2018161412108642 22| VCC± | − Supply V oltage − V
100
RL = 2 kΩCL = 100 pFTA = 25°CSee Figure 3
UNITY-GAIN BANDWIDTHvs
SUPPLY VOLTAGE
VCC± = ±15 VRL = 2 kΩTA = 25°CSee Figure 3
1000
12
8
4
16
10000CL − Load Capacitance − pF
0100
B1
− U
nity
-Gai
n B
andw
idth
− M
Hz
UNITY-GAIN BANDWIDTHvs
LOAD CAPACITANCE
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 VAVD = 1RL = 2 kΩCL = 100 pFSee Figure 1
2.8
2.6
2.4
2.2
1251007550250− 25− 50
3
150
TA − Free-Air T emperature − °C
SR
− S
lew
Rat
e −
V/
s
2− 75
µ
SLEW RATEvs
FREE-AIR TEMPERATURE
NOTE A: Data at high and low temperatures are applicable onlywithin the rated operating free-air temperature rangesof the various devices.
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 38. Figure 39.
Figure 40. Figure 41.
19Submit Documentation Feedback
www.ti.com
1000
40°
20°
60°
CL − Load Capacitance − pF
0°100
− P
hase
Mar
ginÁÁÁÁÁÁÁÁmφ
PHASE MARGINvs
LOAD CAPACITANCEÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 V
RL = 2 kΩTA = 25°CSee Figure 3
10°
30°
50°56°
54°
52°
50°
48°
46°
44°
2018161412108642
58°
22
| VCC± | − Supply V oltage − V
− P
hase
Mar
gin
42°0
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏRL = 2 kΩCL = 100 pFTA = 25°CSee Figure 3ÁÁÁÁÁÁÁÁmφ
PHASE MARGINvs
SUPPLY VOLTAGE
− P
hase
Mar
ginÁÁÁÁÁÁÁÁÁÁmφ 60°
55°
50°
45°
40°
1251007550250−25
65°
150TA − Free-Air T emperature − °C
35°−75
ÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏÏVCC± = ±15 VRL = 2 kΩTA = 25°CSee Figure 3
PHASE MARGINvs
FREE-AIR TEMPERATURE
−50
NOTE A: Data at high and low temperatures are applicable onlywithin the rated operating free-air temperature rangesof the various devices.
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
TYPICAL CHARACTERISTICS (continued)
Figure 42. Figure 43.
Figure 44.
20 Submit Documentation Feedback
www.ti.com
APPLICATION INFORMATION
Input Offset Voltage Nulling
4.7 kW
1 kW
VCC+
OUT
IN-
IN +
VCC-
+
-
4.7 kW
-
+
VCC-
OUT
VCC+
10 kW
IN-
IN+
(a) STANDARD ADJUSTMENT (b) ADJUSTMENT WITH IMPROVED SENSITIVITY
Voltage-Follower Applications
RF
I 1 mAF £
-
+VI
VO
VCC-
VCC
C = 20 to 50 pFF
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEED
PRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
The TLE2027 series offers external null pins that can be used to further reduce the input offset voltage. Thecircuits of Figure 45 can be connected as shown if the feature is desired. If external nulling is not needed, thenull pins may be left disconnected.
Figure 45. Input Offset Voltage Nulling Circuits
The TLE2027 circuitry includes input-protection diodes to limit the voltage across the input transistors; however,no provision is made in the circuit to limit the current if these diodes are forward biased. This condition can occurwhen the device is operated in the voltage-follower configuration and driven with a fast, large-signal pulse. It isrecommended that a feedback resistor be used to limit the current to a maximum of 1 mA to prevent degradationof the device. Also, this feedback resistor forms a pole with the input capacitance of the device. For feedbackresistor values greater than 10 kΩ, this pole degrades the amplifier phase margin. This problem can bealleviated by adding a capacitor (20 pF to 50 pF) in parallel with the feedback resistor (see Figure 46).
Figure 46. Voltage Follower
21Submit Documentation Feedback
www.ti.com
Macromodel Information
8
ro2
7
12
VCC+
IN+
IN-
VCC-
1
2dp
rp11
rc1c1 rc2
Q2Q1
13 14
3
re1 re2
4
lee
ve- +
54
10
reecee
53
vc
+
-r2
6
gcm ga
de
dc
vb
9
+
-
egnd
99
+
-fb
C2
vlim
+
-
ro1
5
OUT
90
hlim
+ dip
-
91
92
dln
vip vin
+
- +
-
.subckt TLE2027 1 2 3 4 5*
c1 11 12 4.003E-12c2 6 7 20.00E-12dc 5 53 dzde 54 5 dzdlp 90 91 dzdln 92 90 dxdp 4 3 dzegnd 99 0 poly(2) (3,0)
(4,0) 0 5 .5fb 7 99 poly(5) vb vc ve
vlp vln 0 954.8E6 −1E9 1E9 1E9 −1E9ga 6 0 11 12
2.062E-3gcm 0 6 10 99
531.3E-12iee 10 4 dc 56.01E-6hlim 90 0 vlim 1Kq1 11 2 13 qx
q2 12 1 14 qxr2 6 9 100.0E3rc1 3 11 530.5rc2 3 12 530.5re1 13 10 −393.2re2 14 10 −393.2ree 10 99 3.571E6ro1 8 5 25ro2 7 99 25rp 3 4 8.013E3vb 9 0 dc 0vc 3 53 dc 2.400ve 54 4 dc 2.100vlim 7 8 dc 0vlp 91 0 dc 40vln 0 92 dc 40
.model dx D(Is=800.0E-18)
.model qx NPN(Is=800.0E-18Bf=7.000E3).ends
TLE2027-EPExcalibur™ LOW-NOISE HIGH-SPEEDPRECISION OPERATIONAL AMPLIFIERSLOS511–JUNE 2007
APPLICATION INFORMATION (continued)
Macromodel information provided was derived using Microsim Parts™, the model generation software used withMicrosim PSpice™. The Boyle macromodel (see Note and Figure 47) and subcircuit (see Figure 48) weregenerated using the TLE202x7 typical electrical and operating characteristics at 25°C. Using this information,output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases):
• Maximum positive output voltage swing • Gain-bandwidth product• Maximum negative output voltage swing • Common-mode rejection ratio• Slew rate • Phase margin• Quiescent power dissipation • DC output resistance• Input bias current • AC output resistance• Open-loop voltage amplification • Short-circuit output current limit
NOTE:
G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, "Macromodeling ofIntegrated Circuit Operational Amplifiers", IEEE Journal of Solid-State Circuits, SC-9,353 (1974).
Figure 47. Boyle Macromodel
Figure 48. TLE2027 Macromodel Subcircuit
22 Submit Documentation Feedback
PACKAGING INFORMATION
Orderable Device Status (1) PackageType
PackageDrawing
Pins PackageQty
Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
TLE2027MDREP ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
V62/06674-01XE ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part ina new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please checkhttp://www.ti.com/productcontent for the latest availability information and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirementsfor all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be solderedat high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die andpackage, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHScompatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flameretardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak soldertemperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it isprovided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to theaccuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to takereasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis onincoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limitedinformation may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TIto Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLE2027-EP :
• Catalog: TLE2027
• Military: TLE2027M
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Military - QML certified for Military and Defense Applications
PACKAGE OPTION ADDENDUM
www.ti.com 18-Sep-2008
Addendum-Page 1
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
TLE2027MDREP SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TLE2027MDREP SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and otherchanges to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latestissue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of salesupplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s termsand conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessaryto support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarilyperformed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products andapplications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provideadequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI components or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty orendorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alterationand is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altereddocumentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or servicevoids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirementsconcerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or supportthat may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards whichanticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might causeharm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the useof any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is tohelp enable customers to design and create their own end-product solutions that meet applicable functional safety standards andrequirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the partieshave executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use inmilitary/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI componentswhich have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal andregulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components whichhave not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of suchcomponents to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2012, Texas Instruments Incorporated