Verification Report for: Carbon Credit Solutions Inc. Tillage Project #21 (#6192-2129)
Date: December 18, 2019
This Verification report has replaced the previous version issued on December 4, 2017 covering the
same emission reduction reporting period.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Verification Report for: Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129
Proponent:
Carbon Credit Solutions Inc.
Prepared by:
Brightspot Climate Inc.
Prepared for: Alberta Climate Change Office
Version:
Final
Date:
December 18, 2019
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 2 of 77
Table of Contents 1.0 Summary – Offset Project ..................................................................................... 4 1.1 Summary – Facility ........................................................................................................ 7 2.0 Introduction ........................................................................................................ 8
2.1 Objective ............................................................................................................ 8 2.2 Scope ................................................................................................................. 9 2.3 Level of Assurance ............................................................................................... 9 2.4 Criteria ............................................................................................................... 9 2.5 Materiality ......................................................................................................... 10
3.0 Methodology ...................................................................................................... 10 3.1 Procedures ........................................................................................................ 10 3.2 Team ................................................................................................................ 23 3.3 Schedule ........................................................................................................... 25
4.0 Results ............................................................................................................. 26 4.1 Assessment of Internal Data Management and Controls ........................................... 26 4.2 Assessment of GHG Data and Information ............................................................. 28 4.3 Assessment against Criteria ................................................................................. 29 4.4 Evaluation of the GHG Assertion ........................................................................... 34 4.5 Summary of Findings .......................................................................................... 34 4.6 Opportunity for Improvement .............................................................................. 36
5.0 Closure ............................................................................................................. 36 5.1 Verification Statement ........................................................................................ 36 5.2 Limitation of Liability .......................................................................................... 36 5.3 Confirmations .................................................................................................... 37
6.0 References ........................................................................................................ 38 Appendix A: Final Verification Plan and Sampling Plan ............................................................ 39 Appendix B: Statement of Qualifications ............................................................................... 64 Appendix C: Findings and Issues ......................................................................................... 67 Appendix D: Statement of Verification .................................................................................. 69 Appendix E: Conflict of Interest Checklist ............................................................................. 73 Appendix F: Supplemental Diagrams/Tables/Figures .............................................................. 76
List of Tables Table 1: Risk Assessment ................................................................................................... 15 Table 2: Findings of Data Integrity Verification Procedures ...................................................... 27 Table 3: Findings of GHG Data and Information Verification Procedures .................................... 28 Table 4: Findings of Criteria Verification Procedures ............................................................... 30 Table 5: Offset Criteria Assessment ..................................................................................... 33 Table 6: Summary of Findings ............................................................................................ 35 Table 7: Confirmation Findings ............................................................................................ 37 Table 8: Detailed Findings and Issues Log ............................................................................ 68 Table 9: Supporting Documentation Reviewed ....................................................................... 77
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 3 of 77
Instructions are in italics throughout and should not be deleted when report is complete. Some instructions are specific to the verification of facilities and for offset projects. The document is not restricted but do not alter the format, the layout, the headings or the overall ‘look and feel’ of the document. If if is more usefule to paste information outside of the text box, use the empty line just below the text box to drop text or tables int. This should not change the headings or the formats. There are several dropdown boxes in the document that must be completed.
• Complete report in Verdana 10pt font (no italics). • After the report is complete, right click the table of contents and ‘update field’ which will
update page numbers in Table of Contents. • If an instruction only applies to facilities or only applies to offsets indicate ‘not applicable’. • Appendix F is available for additional tables, diagrams etc.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 4 of 77
1.0 Summary – Offset Project
Item Description
Project Title
Enter project title (must match the registry project title)
Carbon Credit Solutions Inc. Tillage Project #21
Project Description
Provide a brief description of the project and baseline conditions.
This project consists of the aggregation of carbon offsets generated from the direct and indirect reductions of greenhouse gas (GHG) emissions through zero tillage management in Alberta. The management of land using zero tillage results in reduced fossil fuel use by farm equipment, reduced fossil fuel use for the production of fertilizer and other amendments, and a decrease in the amount of soil carbon and nitrogen that is released to atmosphere. The project proponent is Carbon Credit Solutions Inc. This Offset Project Plan – Project #21 has been completed in accordance with the Alberta Offset System Conservation Cropping Quantification Protocol v1.0, April 2012 and Technical Guidance for Offset Project Developers v4.0 (February 2013).
Project Location
Include the latitude and longitude for each unique location or installation. Include legal land location if applicable and other information identifying the unique location.
Various farms throughout Alberta within the Parkland and Dry-Prairie eco-zones
Project Start Date
Enter the project start date.
January 1, 2014
Offset Start Date
Enter the start date for offset credit generation.
January 1, 2014
Offset Crediting Period
Enter the offset crediting period, including the offset start date. Include day, month year.
January 1, 2014 – December 31, 2020
Reporting Period
Enter the reporting period being verified.
January 1, 2015 – December 1, 2017
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 5 of 77
GHG Assertion (Actual Emission Reductions/Sequestration Achieved)
Enter the actual emissions reductions / sequestration for the reporting period. Enter serial numbers if available.
Vintage Year Emission Reduction
2015 18,964 tonnes CO2e
2016 38,331 tonnes CO2e
2017 111,043 tonnes CO2e
Total 168,338 tonnes CO2e
Protocol
Indicate the relevant protocol (if applicable)
Conservation Cropping Quantification Protocol version 1.0, April 2012
Ownership
Enter offset project owner.
Carbon Credit Solutions (CCSI) has the purchased right to register and sell the emission reduction credits from this project by contractual agreements with the farms involved. Land title records exist to demonstrate land ownership, and Consent Forms signed by all landowners exist to demonstrate ownership of offsets where landowner and farmer are not the same. Master contracts between the farmer CCSI establish CCSI’s right to purchase, register and sell the offsets.
Project Activity
State how the project activity meets the eligibility requirements
The project must meet the eligibility criteria stated in Part 3, Section 16 of the Carbon Competitiveness Incentive Regulation (CCIR). In order to qualify, emission reductions must:
• Occur in Alberta; • Result from an action taken that is not otherwise
required by law at the time the action is taken; • Result from actions taken on or after January 1,
2002; • Occur on or after January 1, 2002; • Be real, demonstrable, quantifiable and verifiable; • Be quantifiable and measurable, directly or by
accurate estimation using replicable techniques.
The verification included an evaluation of these criteria as well as the specific applicability criteria described in the Protocol. The results of this analysis are described in Section 4.3 of this report.
Project Contact
Enter contact name, company name, mailing address, phone number and email address.
Carley Laxdal Credit Development Manager Carbon Credit Solutions Inc. +1 (403)912-9132
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 6 of 77
Verifier
Verifier name, verifier’s company name, address, phone number email etc.
Aaron Schroeder, P.Eng.
Brightspot Climate
401 – 409 Granville Street
Vancouver BC V6C 1T2
+1 (604) 353-0264
Verification Team Members
Include verification team members, roles, training, training dates and qualifications.
Aaron Schroeder, P.Eng. Roles: Lead Verifier and Designated Signing Authority Training: Greenhouse Gas Verification – ISO 14064- 3, Canadian Standards Association, 2012; Instructor – Greenhouse Gas Verification – ISO 14064-3, University of Toronto, 2015 – 2018
Michelle Stelmach, P.Ag. Role: Associate Verifier Training: GHG Validation and Verification, ISO 14064-3, University of Toronto, October 2016
Desarée da Cruz Role: Verifier in training
Deepika Mahadevan, P.Eng. Role: Peer Reviewer Training: Greenhouse Gas Verification
– ISO 14064-3, Canadian Standards Association
Designated Signing Authority
Enter the designated signing authority for this verification.
Aaron Schroeder, P.Eng. Brightspot Climate 401 409 Granville Street Vancouver BC V6C 1T2 +1 (604) 353-0264 [email protected]
Verification Strategy
Describe the verification strategy used for the verification, including rationale for the approach. Note, if a controls reliance is used, provide justification for how the project is able to support this approach.
The verification strategy applied a largely substantive approach. The verification procedures, which are detailed later in this section, were designed to test the activity data directly, wherever practical. By applying this approach, the verification did not rely heavily on the Responsible Party’s controls, but rather relied on the substantive evidence collected from verification procedures that reviewed metered data, data directly from invoices and independent laboratory reports, for example.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 7 of 77
1.1 Summary – Facility
Item Description
Facility Name and Company Name
List company name and facility name.
Not applicable for offset verification reports
Facility Description
Provide a brief description of the facility.
Not applicable for offset verification reports
Baseline Emissions Intensity Description
List the approved BEIA and the baseline years.
Not applicable for offset verification reports
Reporter Contact
Enter contact name, company name, mailing address, phone number and email address.
Not applicable for offset verification reports
GHG Assertion
Enter the actual emissions, production, emissions intensity and the reduction target being verified.
Not applicable for offset verification reports
Verifier
Verifier name, verifier’s company name, address, phone number email etc.
Not applicable for offset verification reports
Verification Team Members
Include verification team members, roles, training, training dates and qualifications.
Not applicable for offset verification reports
Designated Signing Authority
Enter the designated signing authority for this verification.
Not applicable for offset verification reports
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 8 of 77
2.0 Introduction Provide an introduction to the facility or project, the verification, and the background.
For Offset Project: summary of offset project baseline, changes to the baseline since project start date and summary of changes at the project since the offset project start date or baseline period.
For Facilities: Description of compliance or baseline report, facility/project boundary, facility identification information, GHG historical performance, summary of changes since the baseline or since the last compliance report.
Summary of Offset Project Baseline
This project consists of the aggregation of carbon offsets generated by individual farmers through conservation cropping management in Alberta. These direct and indirect emission reductions are generated in accordance with the April 2012 Quantification Protocol for Conservation Cropping, v1.0. Conservation Cropping (CCP) management within Alberta is defined based upon the area, Parkland or Dry Prairie, in which the management occurs.
The CCP used a performance standard baseline methodology to quantify GHG emission reductions resulting from conservation cropping management practices. This means that sector level performance based on 2006 Census data was used to establish a sector level baseline for Alberta based on best practices for the sector and known levels of adoption of reduced and no till agriculture within Alberta’s Eco zones. The quantification of the emission reduction for each participating farm is calculated simply as the product of the eligible land area and the appropriate emission reduction factor.
Summary of Changes
The Responsible Party’s Offset Project Report (OPR) indicates that there have been no changes to the project boundaries and no equipment changes during the reporting period.
The OPR states that the project’s boundaries, operations and major sources of greenhouse gas emissions have not changed from those previously reported.
2.1 Objective Describe the objective of the verification (should include expressing an opinion).
The objective of the verification is as follows:
• to issue an verification statement on whether the GHG assertion is without material discrepancy;
• to issue an verification report that provides details of the verification activities; and • to complete the “confirmations” activities defined in the Alberta Climate Change Office
Standard for Validation, Verification and Audit, Section 5.1.3.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 9 of 77
2.2 Scope Define the scope in terms of: geographical, organizational, activities and processes, sources, sinks, categories and greenhouse gases included (considering the completeness of the inventory), GHG assertion time period.
For offset verifications: include the serial range (i.e. XXXX-XXXX-XXX-XXX-XXX-XXX to XXXX-XXXX-XXX-XXX-XXX-XXX) if assigned (i.e. in the case of government verification a serial range will be available, otherwise not applicable).
For Facilities: ensure all specified gases and source categories are evaluated. Include list of negligible emission sources and justification for Emission Performance Credits (EPCs). Include listing of end products.
Project Name: Carbon Credit Solutions Inc. Tillage Project #21
Serial Range: To be assigned at registration.
Organizational Boundary: Aggregation of farms throughout Alberta
Geographic Boundary: Various farms throughout Alberta within the Parkland and Dry-Prairie eco-zones
Physical Operations: No-till cropping
Emission Sources: Soil Carbon and Nitrogen Dynamics Field Operations
IPCC GHGs Emitted/Removed: Carbon Dioxide (CO2)
Methane (CH4)
Nitrous Oxide (N2O);
remaining IPCC GHGs were not emitted in the baseline or project condition.
Reporting Period: January 1, 2015 – December 1, 2017
2.3 Level of Assurance The verification was conducted to a reasonable level of assurance.
Choose type of verification from the dropdown box above.
Provide explanation on level of assurance.
The Standard for Validation, Verification and Audit, Version 3.0, December 2018 requires that verifications must be designed and completed to a reasonable level of assurance.
2.4 Criteria Outline the program criteria used and relevant supporting documentation (acts, regulations, protocols, standards, guidance documents, project documentation etc).
The program criteria used and relevant supporting documentation is as follows:
• Climate Change and Emissions Management Act
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 10 of 77
• Carbon Competitiveness Incentive Regulation 255/2017, with amendments up to and including Alberta Regulation 96/2018
• Standard for Validation, Verification and Audit, Version 3.0, December 2018. Alberta Climate Change Office
• Standard for Greenhouse Gas Emission Offset Project Developers, Version 2.0, July 2018 • Technical Guidance for the Assessment of Additionality, Version 1.0, May 2018 • Conservation Cropping Quantification Protocol version 1.0, April 2012
2.5 Materiality Define the materiality of the verification.
The materiality threshold is defined in The Standard for Validation, Verification and Audit, Version 3.0, December 2018. For this verification, the materiality threshold is 5%.
3.0 Methodology Statement that the verification is performed according to ISO 14064-3.
Summary of the assessments/tests/reviews/evaluations that were conducted during the verification.
This verification was designed and completed according to the requirements of the ISO 14064-3 Standard.
The following verification activities (assessments/tests/reviews/evaluations) were conducted through the course of this verification. The specific verification activities that were conducted are detailed in the Verification Plan, which is appended to this report. They are also listed with the verification findings throughout section 4 of this report.
• Observations: the site visit included a tour of the farm sites to observe equipment used and confirm farming practices implemented. A file review at the Responsible Party’s office was also completed including a demonstration of their data management system.
• Review of documentation: Documents reviewed in the office visit included Farmer Contracts, Land Titles, Landlord Agreements, Land Area checks, Irrigation evidence, Equipment Photos, Crop Insurance, Crop Plans and P.Ag Signoffs.
• Recalculation: the emissions and production quantities were recalculated using d original data sources and by applying the quantification methodologies stated in the Responsible Party’s Offset Project Report; the methods for calculating any averages used in the emission quantification were recalculated and evaluated for accuracy and appropriateness;
• Inquiry: the site visit included an interview of the Aggregation Admin Service Leader. • Analytical procedures: a year-over-year comparison of overall emissions offsets was
performed.
3.1 Procedures Description of how the verification was conducted including: description of the nature, scale and complexity of the verification activity, confidence and completeness of the responsible party’s
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 11 of 77
GHG information and assertion, assessment of GHG information system and its controls, assessment of GHG data and information, assessment of GHG information system and controls, assessment against criteria, evaluation of the GHG assertion.
The verification strategy applied a largely substantive approach. The verification procedures, which are detailed later in this section, were designed to test the activity data directly, wherever practical. By applying this approach, the verification did not rely heavily on the Responsible Party’s controls, but rather relied on the substantive evidence collected from verification procedures that reviewed metered data, data directly from invoices and independent laboratory reports, for example.
Regarding the scale and complexity of the verification procedures, the verification risk assessment was leveraged to design verification activities appropriate to address the inherent, controls and detection risk evaluated in relation to each activity data and boundary condition. In most cases, these verifications involved review of documentation, recalculation or analytical procedures designed to produce verification evidence to support the accuracy, completeness and consistency of the information. All activity data and boundary conditions were evaluated through the verification risk assessment and verification activities were designed and completed commensurate with the verification risk assessed.
In a similar way, the data integrity, quantification methodologies and quantification itself were assessed through the verification risk assessment. Verification procedures were designed and completed to address each of these key areas.
Verification evidence was developed from each of these verification activities, which was used to establish a verification conclusion regarding the GHG information systems, the Responsible Party’s controls and ultimately, the GHG Assertion.
Describe steps of the verification including planning, assessment, site visit, off-site verification, and report preparation.
The verification was conducted according to the ISO 14064-3 standard, which establishes four primary phases of a greenhouse gas verification as described in this section. The relevant sections from the ISO standard are noted below.
Agreement (ISO Section 4.3)
The verification level of assurance, objectives, criteria, scope and materiality was affirmed in the contract for services and re-affirmed during a verification kickoff meeting.
A conflict of interest review was conducted prior to beginning work and monitored throughout the verification. A conflict of interest statement is appended to this report.
Internally, Brightspot Climate began documenting the verification upon contract signing. All documentation related to the verification will be maintained for a period of seven years following the date of the verification statement.
Approach (ISO Section 4.4)
Brightspot Climate conducted an initial review of the Project’s greenhouse gas information, primarily by reviewing the reports and the Offset Project Plan. Brightspot Climate prepared a verification risk assessment based on this information, evaluating:
a) the inherent risks of discrepancies for each variable used to calculate each emission source and the general greenhouse gas reporting system;
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 12 of 77
b) the risk that the Responsible Party’s controls are insufficient to detect and prevent each inherent risk from causing a discrepancy in the GHG assertion; and
c) the potential magnitude of each inherent and control risk described above resulting from the contribution of the associated emission source.
This information was used to develop an appropriate verification procedure for each identified risk. Each procedure was designed to reduce the probability that the verification would not detect a discrepancy that has not been corrected by the Responsible Party’s controls. The tolerable error for each emission source is stated in the verification risk assessment.
Generally, a substantive approach was applied to the verification. Therefore, the verification procedures relied more heavily on data analysis than on controls testing.
Verification Plan
Brightspot Climate developed a Verification Plan that documents the level of assurance, verification objective, verification criteria, verification scope, and materiality. Additionally, the Verification Plan provides general description of the Project, documents operational and organizational changes that have occurred since the previous verification, explains the Project’s control environment, and describes the safety requirements of the site visit.
Assessment (ISO Sections 4.5 – 4.7)
The verification procedures consist primarily of tests, analysis and review focused on the following six critical areas:
a) The completeness and relevance of emission sources included in the GHG Assertion;
b) The consistency of the emission sources and quantification methodologies between the Protocol, the Offset Project Plan, Offset Project Report and the tools used to quantify the emission reduction;
c) The accuracy and level of transparency of measured and estimated data sources, data integrity of electronic and manual data transfers and transcription between data systems and the GHG calculation;
d) The accuracy of the GHG emissions reduction calculations;
e) The completeness, accuracy and transparency of information presented in the Offset Project Plan and Offset Project Report documents, including the implementation of stated methodologies and emission factors in the quantification of emissions reductions; and
f) The accuracy of transcription of final calculated values into the GHG Assertion, including the “confirmations” required by ACCO as described in the ACCO Standard for Validation, Verification and Audit.
The principles defined in the preceding six areas are defined in ISO 14064-1 (accuracy, completeness, consistency, relevance and transparency).
Site Visit
The site visit of the Carbon Credit Solutions Inc. office was conducted via phone interview by Michelle Stelmach with Carley Laxdal who described the data system. A document review (Farmer Contracts, Land Titles, Landlord Agreements, Land Area checks, Irrigation evidence, Equipment Photos, Crop Insurance, Crop Plans and P.Ag Signoffs) was completed on-line using the company’s on-line record system. Seven Young also answered questions pertaining to the farm visits.
The following Responsible Party staff were interviewed regarding various aspects of the Project.
• Carley Laxdal, Credit Development Lead
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 13 of 77
• Seven Young, Field Representative/Sales Agent
The farm site visits were conducted on November 21 - 22 and December 3-5, 2019 by Michelle Stelmach. Seventeen farms representing approximately 7% of the total aggregated assertion were visited. Farmers were interviewed about their farming practices and the tillage equipment was observed and compared to the photos on file with Carbon Credit Solutions Inc.
Further details of the verification activities that were conducted on site, including observations and inquiries, are provided in Section 4 of this report.
Verification Procedures
The remainder of the verification procedures was conducted through a desk review following receipt of the draft GHG Assertion.
Through the course of the assessment phase of the verification, Brightspot Climate issued questions and requests for additional documentation and data. These requests were consolidated in a simple electronic tracking document to maintain a common record of communication.
The Responsible Party had the opportunity to address any issues that were raised through the course of the verification before they were documented as discrepancies in the Verification Report.
Evaluation and Statement (ISO Sections 4.8 – 4.9)
Following the completion of all verification procedures and consideration of all information received from the Responsible Party, the verifier was tasked with concluding whether the GHG assertion is without material discrepancy and whether the verification reviewed sufficient and appropriate evidence to support a reasonable level of assurance.
If any outstanding discrepancies remained, their materiality would have been calculated according to ACCO guidance such that both the aggregate net quantitative error and the absolute quantitative error could be reported. In such circumstances, qualitative discrepancies would be evaluated based on the potential impact on the GHG assertion and the potential impact on the Intended User’s ability to use the reported information.
Peer Review
The independent Peer Reviewer conducted a complete review of the verification. The peer review process examined:
a) The completeness of the verification risk assessment; b) The appropriateness of the verification procedures considering the inherent and control
risks identified in the verification risk assessment; c) The appropriateness of any sampling conducted in each of the verification procedures; d) The completeness of each verification procedure, including the verifiers documentation
of work completed; e) Closure of any issues raised by the verifier through the course of the verification; f) The sufficiency and appropriateness of all evidence reviewed through the verification to
support a reasonable level of assurance; and g) A review of the final Verification Statement and Conflict of Interest Statement.
Verification Report
The Verification Report includes a Verification Statement, Statement of Qualifications, Conflict of Interest Statement and a report on the findings of the verification. The final Verification and Sampling Plan has been appended to the Verification Report, including the results of the verification risk assessment.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 14 of 77
Describe how the risk based approach was implemented in the sampling plan. Identify categories of risk including inherent risk, and detection risk (organization and verifier). Include the Verification Plan with the Sampling Plan in Appendix A. Paste the risk assessment table in this section.
Verification risk is defined as the risk of an incorrect verification conclusion. It can be calculated as the product of
• The Project’s inherent risks; • The Responsible Party’s control risks; and • The detection risks associated with the verifier’s verification procedures.
Inherent Risk × Control Risk × Detection Risk = Verification Risk
The verifier cannot affect the inherent risk or the control risk. Therefore, to reduce the overall verification risk and reach the agreed level of assurance (defined in the verification scope), the verifier must design verification procedures that reduce the detection risk.
Each inherent and control risk was provided with the risk score (high/medium/low). The risk analysis of inherent and control risks considers both the magnitude of the activity data or inventory component on the overall GHG assertion as well as the probability that the risk will result in a discrepancy, as assessed by the verifier.
The Verification Risk Assessment Summary on the following pages describes the following information: • Activity Data / Inventory Component: The boundary, eligibility requirement, data
component or reporting activity being evaluated. • Inherent Risk: The verifier’s evaluation of inherent risk. Inherent risks have been
categorized according to the ISO 14064-1 principles (accuracy, completeness, consistency, relevance, transparency).
• Control Risk: A description of the Responsible Party’s controls (if any controls are applicable) and the verifier’s evaluation of control risks.
• Max Detection Risk: The maximum detection risk that can be applied and still result in an overall verification risk that meets the agreed level of assurance.
• Designed Detection Risk: The detection risk of the verification procedure that the verifier intends to complete. Note that the designed detection risk must always be equal to or lower than the maximum detection risk.
• Verification risk: the product of the inherent, control and (designed) detection risk, as defined in the equation above.
Important note: The verification strategy for this verification applies both substantive tests and control tests. Substantive tests are designed to focus on directly testing activity data or inventory components and their associated inherent risks. Control tests are designed to focus on testing the Responsible Party’s controls and if the test is successful, relying on the Responsible Party’s control. Therefore, control tests indirectly test activity data or inventory components.
Each verification procedure listed in the following table denotes if the procedure is a substantive or control test.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 15 of 77
Table 1: Risk Assessment
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Protocol Applicability Requirements
Annual crops See “Field Level Eligibility”
Disturbance levels
See “Field Level Eligibility”
Reversal events
Completeness – Low
Farm operators may not report all reversal events.
Control: CCSI interviews farmers to determine if reversal events have occurred.
Control risk: Interviews may not have identified reversal events (low risk).
High High Control test – Interview farm operators during farm visits to determine if reversals have occurred over the 2015-2017 crop years.
Low
Ownership See “Field Level Eligibility”
Irrigation, manure incorporation, reseeding
See “Field Level Eligibility”
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 16 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Quantification Data
Cropped area Accuracy – Low
Land area claimed may not be substantiated.
Control: The land area claimed by the farm operator is compared against land titles and aerial images.
Control risk: control may not be applied (low risk).
High High Substantive test (sampled) - Compare quantities shown in DMS to aerial images (Google Earth).
Low
GHG reduction factors
Accuracy – High
Transcription of GHG reduction factors from protocol may be inaccurate.
Control: DMS applies the GHG reduction factor based on the ecozone determined by DMS.
Control risk: There may be an error in the DMS ecozone algorithm (low risk).
Low Low Substantive test – Recalculate GHG reduction factors using values in the Protocol and compare to factors applied in DMS.
Medium
Ecozone Accuracy – Medium
Incorrect ecozone may be assigned to a piece of land.
Control: DMS applies the ecozone.
Control risk: There may be an error in the DMS ecozone algorithm (low risk).
High Low Substantive test – Compare all legal land descriptions in the aggregated Project to the Alberta Agriculture and Forestry ecozone database.
Low
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 17 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Farm Level Eligibility and Documentation
Aggregator / Farm Operator contract
Completeness – Medium
The contract between the aggregator and the farmer may be missing or outdated.
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that aggregator/farm operator contracts have been executed and uploaded on DMS/DocSys.
Low
Field Level Eligibility and Documentation
Land title certificate
Accuracy - Low
Completeness – Low
Land title certificates may be missing or outdated
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that land title certificates are uploaded on DMS/DocSys.
Low
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 18 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Farm Operator / Landowner contract
Completeness – Low
The farm operator and landowner may not have a contract or the contract may be missing from the file.
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that farm operator/landlord contracts have been executed and the acres are within the limits of the land title certificates.
Low
Annual crops – farm records
Accuracy – Low
Completeness – Medium
Potential errors in automated data management processes or manual entries
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that farm records indicate an annual crop was grown on land in sample of aggregated assertion.
Low
Annual crops – supporting records approved by a Professional Agrologist
Completeness – Medium
Approval of supporting records by a Professional Agrologist may be missing
Control: The Quality Manager reviews each farm file for completeness.
Control risk: The Quality Manager may not complete the file review (medium risk).
High Medium Substantive test (sampled) – Confirm that farm records indicate an annual crop was grown on land in sample of aggregated assertion.
Low
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 19 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Disturbance – farm records (including manure incorporation and reseeding events)
Completeness – Low
Farm records may not completely represent the disturbance events.
Control: CCSI Sales Agents interview farmers to confirm information provided by farmers is accurate and complete.
Control risk: Interview may fail to identify or record disturbance events, (medium risk)
High Medium Controls test – Interview farm operators with a series of questions during farm visits to determine if all disturbances that occur on the farm have been recorded in DMS. These questions include both typical and atypical farm activities that may constitute a disturbance event.
Low
Discretionary tillage –disclosure
Completeness – Low
Farm records may not completely represent discretionary tillage events.
Control: CCSI Sales Agents interview farmers to confirm information provided by farmers is accurate and complete.
Control risk: Interview may fail to identify or record discretionary tillage. (medium risk)
High High Substantive test (sampled) – Interview farm operators regarding discretionary tillage during farm visits.
Low
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 20 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Seeding equipment – record and photographs of equipment used
Accuracy – Medium Completeness – Medium
Photographs may not be on file or may not clearly illustrate opener width and spacing
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
Low Low Substantive test (sampled) – Compare equipment photos in the DMS/DocSys to observations made during farm visits. Also compare the measurements of opener width and shank spacing made during farm visits to the values recorded in the DMS.
Low
Irrigation – aerial images and additional farm records approved by a Professional Agrologist
Accuracy – Low
Completeness – Low
Aerial images may not clearly indicate that irrigation occurred on land. Secondary documentation may not be on file.
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (low risk).
High High Substantive test (sampled) – review aerial images to confirm that fields appear to have been irrigated. Review secondary documentation to confirm irrigation.
Low
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 21 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Emmission Quantification and Reporting
Application of the approved quantification protocol
Accuracy (high)
The project developer may not have implemented approved quantification methodologies or applied additional methodologies.
Control: Responsible Party has developed an Offset Project Plan that is intended to conform to the requirements of the approved quantification protocol.
Control Risk: The protocol requirements may not have been implemented correctly (medium)
Low Low Controls test: compare the methodologies described in the Responsible Party’s Offset Project Plan to the methodologies described in the approved quantification protocol.
Low
Substantive test: Recalculate the emission reduction using original metered data and methods described in the approved quantification protocol.
Quantification of emission reduction
Accuracy (high)
Emission reduction calculation may contain arithmetic errors.
The Responsible Party does not have a control specifically designed to address this inherent risk.
Low Low Substantive test: Recalculate the emission reduction using original metered data.
Low
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 22 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Data Integrity
Activity data and emission factor data integrity
Accuracy (high)
Data may not have been accurately transferred between electronic systems and calculation sheets.
Control: The Responsible Party uses electronic data transfers whenever possible to maintain data integrity.
Control Risk: Electronic data transfers may result in errors or may not be available for all data (medium).
Low Low Controls test: Analyze all metered data for abnormal data (zeros, missing data, values outside range).
Medium
Substantive test: Recalculate the complete emission reduction using original data.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 23 of 77
Activity Data/ Inventory Component
Inherent Risk Control Risk Max Detection Risk
Detection Risk Design
Description Verification Risk
Transcription of final emission reduction into Offset Project Report
Accuracy (high)
Final emission reduction may not have been transcribed accurately from calculation spreadsheets into the Offset Project Report.
The Responsible Party does not have a control specifically designed to address this inherent risk.
High Low Substantive test: compare the final emission reduction quantity reported by the Responsible Party to the quantity reported in the Offset Project Report. Also, compare these quantities to the recalculated quantity in previous verification procedures.
Low
3.2 Team List verification team members including peer reviewer(s).
Describe the qualifications and training of the team members and peer reviewer(s) including dates of training and certifications.
For Offsets: fill in the sample Statement of Qualification provided and included in Appendix B.
For Facilities: include the Statement of Qualifications from the facility compliance form in Appendix B.
ISO 14064-3 defines sixteen subject matter areas in which the verifier should demonstrate familiarity (see ISO 14064-3, Section A.2.2.3). The verification team has competencies in each of these sixteen subject matter areas.
Lead Verifier: Aaron Schroeder, P.Eng.
Aaron Schroeder will be the Lead Validator and Designated Signing Authority. His extensive experience quantifying and verifying greenhouse gas emissions satisfies all sixteen subject matter areas defined in the standard.
Biography: Aaron Schroeder has eleven years of professional experience analyzing, quantifying and verifying greenhouse gas emissions in North America. Prior to forming Brightspot Climate Inc. in 2015, Aaron worked for several years leading a team of fifteen greenhouse gas verification and policy analysts across Canada with ICF International. He
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 24 of 77
provided leadership for this team and led the development of ICF’s standardized verification process, conformant with ISO 14064-3. In 2012, ICF’s verification process was accredited by the American National Standards Institute (ANSI).
Mr. Schroeder’s hands on experience conducting greenhouse gas verifications includes numerous engagements for oil and gas extraction and processing, refining, pipeline, electricity generation and petrochemical facilities. Additionally, he has conducted verifications of emission reduction projects in industrial facilities, renewable energy, waste management and agriculture. He is sought after for his expertise devising strategies to bridge the gap between theoretical and practical implementation of methodologies for quantifying, reporting and verifying.
In 2014, the University of Toronto engaged Mr. Schroeder to instruct professional development courses on greenhouse gas inventory and project quantification, reporting and verification. Since 2014, Mr. Schroeder has instructed several of these courses in live, two-day sessions and on-line instruction as a sessional lecturer through the university’s School of Environment. Additionally, Mr. Schroeder has worked with the School of Environment to re-write and update the courses.
Training: Greenhouse Gas Verification – ISO 14064-3, Canadian Standards Association, 2012; Instructor – Greenhouse Gas Verification – ISO 14064-3, University of Toronto, 2015 - 2017
Technical Specialist: Michelle Stelmach, P.Ag.
Biography:
Michelle Stelmach has worked as a Technical Specialist for verification and protocol development initiatives under Alberta’s Specified Gas Emitters Regulation. This work has included performing farm site visits and assisting with the verification planning and procedures for Conservation Cropping, Agricultural Nitrous Oxide Emission Reduction (NERP) and Fed Cattle (Beef Days on Feed) projects.
Michelle has worked with the Hazard Analysis Critical Control Point (HACCP) to design and conduct internal system audits and to meet Canadian Food Inspection Agency standards at the producer level, in feed manufacturing plants and poultry processing plants. She has extensive experience working with agricultural producers across Alberta through her work as Program Advisor and Coordinator with Maple Leaf Foods and Landmark Feeds.
Training: Michelle received GHG Validation and Verification, ISO 14064-3, training through the University of Toronto in October 2016.
Verifier in Training: Desarée da Cruz
Biography: Desarée da Cruz has over seven years experience in Administration across multiple industries. Having supported large and small teams in her different roles, her organization, time management and attention to detail are great assests to the verification team.
Training: Desarée da Cruz graduated with a General Business Diploma from Conestoga College in 2011.
Peer Reviewer: Deepika Mahadevan, P.Eng.
Biography: Deepika Mahadevan, P.Eng. has more than five years of experience conducting greenhouse gas verifications for industrial facilities and emission reduction (offset) projects in jurisdictions across Canada. Her experience includes verifications in the following sectors/project types: Natural gas production (upstream), Oil sands in-situ production, Natural gas processing (midstream), Oil upgrading and refining, Electricity production (natural gas/biomass), Electricity production (renewables), Metals Refining, Wastewater Treatment, Aerobic Composting, and Landfill Gas Capture and Combustion.
Training: Greenhouse Gas Verification – ISO 14064-3, Canadian Standards Association, 2012
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 25 of 77
3.3 Schedule Provide a list or table of verification activities and dates. Indicate when the verification was completed.
Verification Kickoff Meeting October 23, 2019
Draft Verification Plan October 28, 2019
Site Visit November 21, 22 and December 3-5, 2019
Supplementary Information Request December 11, 2019
Draft Verification Report December 13, 2019
Final Verification Report December 18, 2019
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 26 of 77
4.0 Results Add introduction to results section here, if desired.
The verification results are presented in the following five subsections. Subsections 4.1 – 4.3 present the results of the verification procedures for the data integrity (4.1), Quantification Methodologies and Quantification (4.2), and Boundary Conditions and Activity Data (4.3).
4.1 Assessment of Internal Data Management and Controls Provide a summary the information system(s) and its controls for sources of potential errors. Include information on the selection and management of data, process for collecting and consolidating data, data accuracy systems, design and maintenance of the GHG system, the systems and processes that support the GHG information system and results from previous assessments if applicable.
The Project’s GHG quantification is primarily performed in the Carbon Credit Solutions Inc. “Data Management System” database (“DMS”). All data required to quantify emissions reductions for the Project is either manually transcribed into this database or electronically transferred from other spreadsheets. The final calculated quantities from this database are transferred into the Offset Project Report. Carbon Credit Solutions Inc. utilizes a paperless filing system, so all documentation, equipment photos, maps, etc. are scanned or uploaded to their “DocSys” filing system.
DMS includes data controls to prohibit double entries of legal land descriptions. It also automatically assigns the Ecozone. It validates the equipment specification against the applicability criteria of the protocol.
The Responsible Party maintains an Offset Project Plan (OPP) and produces an Offset Project Report (OPR), which document the emission sources, processes for collecting GHG activity data, equations applied to quantify emissions reduction, calculation assumptions, procedure and schedule, the averaging method applied to quantification, and a discussion of GHG data management.
Findings from Previous Verification
This project was previously verified by Ruby Canyon Engineering. Alberta Environment and Parks Directed the Responsible Party to complete a second verification of this project.
“Based on the information collected through inquires conducted during farm visits, it was discovered that one farm (Iron Creek Colony) had injected liquid manure on 610 acres (approx. over 4 quarters). Some of this area was reported to CCSI but not all of it. After further inquiry, it was determined that the farmer didn’t report the correct LLD to CCSI. CCSI was contacted and all of this land was removed from the pool. 450 acres out of 168,338 (0.27%). The total discrepancy is less than 0.27% of the overall asserted emission reduction.”
This discrepancy did not persist in this verification completed in December 2019.
Results of Verification Procedures
There were three verification procedures completed to test data integrity. The results of these procedures are provided in the following table.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 27 of 77
Table 2: Findings of Data Integrity Verification Procedures
GHG Report Element
Verification Procedures Verification Findings
Activity data and emission factor data integrity
Controls test: Analyze data for abnormal data (zeros, missing data, values outside range).
The activity data and emission factor data was analyzed for any abnormal data.
No discrepancies detected.
Substantive test: Recalculate the complete emission reduction using original data.
The complete emission reduction was recalculated using the original data.
No discrepancies detected.
Transcription of final emission reduction into Offset Project Report
Substantive test: compare the final emission reduction quantity reported by the Responsible Party to the quantity reported in the Offset Project Report. Also, compare these quantities to the recalculated quantity in previous verification procedures.
The emission reduction quantity was accurately transcribed into the Offset Project Report.
No discrepancies detected.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 28 of 77
4.2 Assessment of GHG Data and Information Provide a summary of the information found during the verification of the GHG data and a summary of the GHG Assertion that was assessed.
For Facilities: Confirm that the quantification methodologies that were used in the compliance report are the same as those reported in the BEIA.
For Offset Projects: Confirm that the quantification methodologies that were used by the project proponent are the same as those described in the project plan. Indicate which quantification methodologies were used by the project proponent.
The GHG information consists of the activity data applied to quantify emissions reductions, the source documentation for the activity data, the information in the Offset Project Plan, as described in the previous section of this report, and the documentation supporting the boundary, methodologies, meter calibration, and emission factors.
Table 3: Findings of GHG Data and Information Verification Procedures
GHG Report Element
Verification Procedures
Verification Findings
Quantification Data
Cropped area Substantive test - Compare quantities shown in DMS to aerial images (Google Earth).
The Responsible Party uses aerial images from Google Earth to substantiate the land areas claimed.
No discrepancies detected.
GHG reduction factors
Substantive test – Recalculate GHG reduction factors using values in the Protocol.
GHG reduction factors were correctly calculated and applied.
No discrepancies detected.
Ecozone Substantive test (sampled) – Compare all legal land descriptions in the aggregated Project to the Alberta Agriculture and Forestry ecozone database.
The Protocol notes the Ecozone is determined using the map in Figure 5 of the Protocol or online at http://www1.agric.gov.ab.ca/$department/deptdocs.nsf/all/cl11708.
The Responsible Party’s online database, DMS, has a control set up to determine the Ecozone based on this map compared to the LLD of each field.
No discrepancies detected.
Emission Quantification and Reporting
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 29 of 77
GHG Report Element
Verification Procedures
Verification Findings
Quantification of emission reduction
Substantive test – Recalculate the complete emission reduction using original data.
The recalculation of the emission reduction matched Carbon Credit Solution Inc.’s calculation.
No discrepancies detected.
Application of approved quantification protocol
Substantive test – compare the methodologies described in the Responsible Party’s Offset Project Plan to the methodologies described in the approved quantification protocol.
Substantive test – Recalculate the complete emission reduction using original data and methods described in the approved quantification protocol.
The Responsible Party’s Offset Project Plan follows the methodologies described in the quantification protocol.
The recalculation matched the quantity reported by Carbon Credit Solutions. Therefore, the methods applied by the Responsible Party are proven to match the methods described in the quantification protocol.
No discrepancies detected.
Transcription of final emission reduction into Offset Project Report
Substantive test – compare the final emission reduction quantity reported by the Responsible Party to the quantity reported in the Offset Project Report. Also compare these quantities to the recalculated quantity in previous verification procedures.
The Responsible Party’s Offset Project Plan follows the methodologies described in the quantification protocol.
The recalculation matched the quantity reported by Carbon Credit Solutions Inc. Therefore, the methods applied by the Responsible Party are proven to match the methods described in the quantification protocol.
No discrepancies detected.
4.3 Assessment against Criteria Provide a description of how eligibility criteria is met or not met.
For Offset Project: Complete Table 1 to indicate if the GHG Assertion conforms to the Regulation and Standard for Greenhouse Gas Emission Offset Project Developers eligibility criteria.
For Facilities: Delete Table 1 and Indicate if verification criteria are met or not met and explain.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 30 of 77
Table 4: Findings of Criteria Verification Procedures
GHG Report Element
Verification Procedures Verification Findings
Protocol Applicability Requirements
Annual crops See “Field Level Eligibility”
Disturbance levels
See “Field Level Eligibility”
Reversal events Control test – Interview farm operators during farm visits to determine if reversals have occurred over the 2015, 2016 or 2017 crop years.
Ownership See “Field Level Eligibility”
Irrigation, manure incorporation, reseeding
See “Field Level Eligibility”
Farm Level Eligibility and Documentation
Aggregator / Farm Operator contract
Substantive test (sampled) – Confirm that aggregator/farm operator contracts have been signed and filed.
A sample of aggregator/farm operator contracts were viewed and determined to be complete and on file.
No discrepancies detected.
FIELD LEVEL ELIGIBILITY AND DOCUMENTATION
Land title certificate
Substantive test (sampled) – Confirm that current land title certificates correspond with lands included in Project #21.
All land titles in the selected sample were confirmed to be current and match with the lands included in Project #21.
No discrepancies detected.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 31 of 77
GHG Report Element
Verification Procedures Verification Findings
Farm Operator / Landowner contract
Substantive test (sampled) – Confirm that farm operator/landlord contracts have been executed and the acres are within the limits of the land title certificates.
After review of the sample, the farmer operator/landlord contracts were signed, filed and the acres were checked and found to be within the limits of the land title certificates.
No discrepancies detected.
Annual crops – farm records
Substantive test (sampled) – Confirm that farm records indicate an annual crop was grown on land in sample of aggregated assertion.
The farm records that were reviewed in the sample specified that only annual crops were grown.
No discrepancies detected.
Annual crops – supporting records approved by a Professional Agrologist
Substantive test (sampled) – Confirm that farm records indicate an annual crop was grown on land in sample of aggregated assertion.
The data management system was observed and sampled, and it denoted that a Professional Agrologist had reviewed and approved that annual crops were grown.
No discrepancies detected.
Disturbance – farm records (including manure incorporation and reseeding events)
Controls test – Interview farm operators with a series of questions during farm visits to determine if all disturbances that occur on the farm have been recorded in DMS. These questions include both typical and atypical farm activities that may constitute a disturbance event.
Discretionary tillage was identified on one farm during the farm visits.
An immaterial qualitative discrepancy is detailed in Appendix C as Item 17-01.
Discretionary tillage –disclosure
Substantive test (sampled) – Interview farm operators regarding discretionary tillage during farm visits.
Discretionary tillage exceeding the threshold defined in the Protocol was detected on one field during the farm visits.
An immaterial qualitative discrepancy is detailed in Appendix C as Item 17-01.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 32 of 77
GHG Report Element
Verification Procedures Verification Findings
Seeding equipment – record and photographs of equipment used
Substantive test (sampled) – Compare equipment photos in the Carbon Credit Solutions Inc. data management system to observations made during farm visits. Also compare the measurements of opener width and shank spacing made during farm visits to the values recorded in the Carbon Credit Solutions Inc. data management system.
After reviewing a sample of the photos on file the documentation appeared to be consistent with the equipment observed on the farm visits.
No discrepancies detected.
Irrigation – aerial images and additional farm records approved by a Professional Agrologist
Substantive test (sampled) – review aerial images to confirm that fields appear to have been irrigated.
Substantive test (sampled) – confirm that additional farm records, beyond aerial images, have been filed.
After comparing a sample of the irrigated quarter sections in the Responsible Party’s database, the irrigation was clearly viewed on the Google Earth images and AFSC (crop insurance) documentation.
No discrepancies detected.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 33 of 77
Table 5: Offset Criteria Assessment
Offset Eligibility Criteria
Assessment
Reduction or sequestration occurs in Alberta
The aggregated project includes sub-projects in locations throughout Alberta. The Aggregated Project Reporting Sheet was reviewed to confirm all locations are within the Province of Alberta.
Result from actions not required by Law at the time the action is taken
The project activity is not required by municipal, provincial or federal regulations or directives.
Result from Actions taken on or after January 1, 2002 and occur on or after January 1, 2002
The project start date is January 1, 2014
Reduction or sequestrations is real and demonstrable
The emission reduction was demonstrated through measurement and estimation of data required for the quantification. The GHG information presented to the verification team included sufficient and appropriate evidence to substantiate conformance with the Protocol Applicability Requirements and to substantiate the quantification data.
Quantifiable and measurable
The emission reduction was demonstrated through measurement and estimation of data required for the quantification. This data was substantiated by sufficient and appropriate evidence. Table 3 of this report presents the findings of the evaluation of each variable required for the emission reduction quantification.
Verified by a third party verifier that meets the requirements in Part 1 for the Standard for Validation, Verification and Audit.
Brightspot Climate Inc. is an independent third-party verifier that meets the requirements outlined in Section 1 of the Standard for Validation, Verification and Audit. The Lead Verifier and Designated Signing Authority, Aaron Schroeder, is a Professional Engineer and has extensive experience quantifying and verifying greenhouse gas emissions, satisfying all sixteen subject matter areas defined in the ISO 14064-3 Standard.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 34 of 77
4.4 Evaluation of the GHG Assertion The verification assessment is that the GHG Assertion meets the requirements of the Carbon Competitiveness Incentive Regulation
Provide an assessment of the evidence collected during the verification. Determine if the data and information available support the GHG assertion. Provide a conclusion on whether the assertion meets the materiality requirements and the level of assurance agreed to at the beginning of the verification process.
The results of each verification procedure are provided in the preceding three subsections (4.1 – 4.3). Sufficient and appropriate evidence was collected through the verification procedures to reach the verification conclusion at a reasonable level of assurance, which is provided in the Verification Statement.
The data and GHG information provided by the Responsible Party is sufficient to support the GHG assertion.
There was one discrepancy detected through the course of the verification that has not been corrected in the final GHG Assertion. These discrepancies are described in the following section. The aggregated of these discrepancies were within the materiality threshold established at the outset of the verification.
4.5 Summary of Findings Provide a summary of material and immaterial discrepancies expressed in tonnes and as net and absolute error in Table 2. Include whether the discrepancy was an understatement or an overstatement.
Include a more detailed description and log of results in Appendix C the “Issues Log”. This log will include both resolved and unresolved issues from the verification. Unresolved issues should be brought forward to Table 2.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 35 of 77
Table 6: Summary of Findings
Number the finding with the year and provide a unique # for each finding. Note: A detailed description of all material and immaterial findings should be provided in Table 3 of Appendix C. Provide only a summary statement (1-4 sentences) for each unresolved immaterial finding and each material finding (resolved or unresolved). If the finding is a resolved material finding, then put the tonnes net and absolute in the summary description column and indicate n/a in the net and absolute columns. Do not include the tonnes in the total error calculation. Indicate the type of error (qualitative or quantitative). Indicate the Source Category (for facilities) or the Source/Sink (for offsets). Indicate if the finding is an understatement or overstatement. Provide both net and absolute error in tonnes of CO2 eq and as a % of the assertion. Provide the total net error and the total absolute error in tonnes of CO2 eq and as a % of the assertion.
Result Type Summary Description of Finding Source Category or Source/Sink
Understatement / Overstatement
Tonnes CO2e % net
Tonnes CO2e % absolute
001 Immaterial Quantitative
The protocol allows for up to 10% (16 acres) per quarter section to apply discretionary tillage as part of the no-till farming practice.
One farm had recorded 40 acres of discretionary tillage on one quarter section on his application. The Responsible Party did not remove this land from their DMS.
We determined through further investigation that this discrepancy occurred due to a transcription error between the farmer’s application sheet and the DMS. The Responsible Party’s controls failed to detect this error.
Based on our observations and understanding of the controls in the DMS, we found that this error is unlikely to recur frequently.
Overstatement Approximately 3 tonnes CO2e (less than 0.1% of the aggregated assertion.
Approximately 3 tonnes CO2e (less than 0.1% of the aggregated assertion.
Total Error 3 tonnes CO2e 3 tonnes CO2e
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 36 of 77
4.6 Opportunity for Improvement Provide feedback on the data management system and controls, transparency, completeness of the inventory, additions to the quantification methodology document or diagrams, etc. Include positive considerations and observations also.
Identify strengths and weaknesses that may help to improve the report/s for the current facility, sector, and compliance program. Identify ways in which the project/facility could be more easily verified.
Overall, the GHG information was orderly and thoroughly presented.
The quantification spreadsheets were satisfactorily organized and sufficiently transparent to conduct the verification procedures.
Sufficient and appropriate evidence was provided by the Responsible Party to conduct each of the verification procedures.
The Offset Project Plan and Offset Project Report thoroughly document the emission sources, quantification approach, equations, data collection and information controls.
5.0 Closure 5.1 Verification Statement Include the signed verification statement in Appendix D.
Instructions to insert a pdf: 1. Click Insert>Object 2. In the Object dialog box click Create from File and then click Browse. 3. Find the pdf you want to insert then click Insert. 4.Click OK.
For Offset Projects: fill in the sample Verification Statement provided, sign, scan and paste.
For Facilities: paste a signed version of the Verification Statement from the facility compliance form. Include the conclusion on the GHG assertion and any qualification or limitations and the level of assurance.
Provide the verification conclusion in the drop down box below.
The verification conclusion is:
Positive
5.2 Limitation of Liability Include signed Conflict of Interest Checklist in Appendix E.
For Offset Projects: fill in the sample Conflict of Interest Checklist provided, sign, scan and paste.
For Facilities: paste the signed Conflict of Interest Checklist from the facility compliance form.
Insert limitation of liability statement and include information in an Appendix F if applicable.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 37 of 77
5.3 Confirmations Document information confirmed, including any discrepancies or inconsistencies, as per the Confirmations section in the Standard for Greenhouse Gas Verification.
Section 5.1.3 of the Standard for Validation, Verification and Audit document lists nine activities that are beyond the scope of a typical greenhouse gas verification.
Table 7: Confirmation Findings
Confirmation Confirmation Finding
Correct entry of administrative fields such as facility codes and legal locations
The Offset Project Report was reviewed for completeness and accuracy. All project and legal location information is complete and accurate.
Quantification Methodology document is provided and consists of the required components
The Responsible Party has documented all relevant methodologies, procedures and controls in the Offset Project Plan and the Offset Project Report.
Simplified process flow diagrams and energy diagrams
The Responsible Party’s Offset Project Plan and Offset Project report provide process flow diagrams, which were reviewed and found to accurately represent the Project.
Fuel usage This requirement is not applicable to Offset Projects.
Additional request items/forms are complete and reasonable justification provided where needed
The Statutory Declaration was reviewed and found to be complete.
The APPS and APRS were not in effect when the emission reduction assertion was made.
N/A is checked on pages in the reporting form that do not apply
This requirement is not applicable to Offset Projects.
For forecasting facilities, the fund to credit ratio was met for all four reporting periods
This requirement is not applicable to Offset Projects.
For oil sands facilities, the area fugitive calculations are accounted for, as required
This requirement is not applicable to Offset Projects.
Project report information details as required The Responsible Party has prepared an Offset Project Report that meets all the requirements specified in the Standard for Greenhouse Gas Emission Offset Project Developers, Version 2.0, July 2018
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 38 of 77
6.0 References Author. Year. Title. (no hyperlinks)
The documents reviewed through the course of the verification include:
See Appendix F.
Page 39 of 77
Appendix A: Final Verification Plan and Sampling Plan
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 63 of 77
Information to be included in the Verification Plan and Sampling Plan:
Revisions to the sampling plan
Date originally sent to Facility/project
Level of assurance agreed with the facility/project developer
Verification scope
Verification criteria
Amount and type of evidence (qualitative and quantitative) necessary to achieve the agreed level of assurance
Methodologies for determining representative samples
Sampling Plan and Procedures
Risk Assessment: Risks of potential errors, omissions or misrepresentations that are identified throughout the verification process including:
- Details of site visit
-offset/facility boundaries
- Methodologies, emissions factors and conversions used
- Comparability with the approved baseline
- Conformance to the program criteria
- Integrity for the responsible party’s data management system and control (organization chart, GHGH management plan, personnel/consultant training, protocols used, control system documentation, software/program documentation/certifications)
- Greenhouse gas data and information, including the type of evidence collected, verification testing and crosschecking, inventory of emission sources
- Discussion of data management, (measurement, fuel sampling, calibration, consistent use of standard conditions, data storage, procedures to fill missing data; procedures to repair inconsistent data, adjustment of variables and factors)
- Other relevant information
+1 (604) 353-0264 • www.brightspot.co • [email protected]
Carbon Credit Solutions Inc.
Tillage Project #21(6192-2129) Verification Plan
October 23, 2019
This page intentionally blank
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
i
Terminology
ISO 14064-2 defines the following terms used in the context of a GHG verification:
GHG Assertion: a declaration or factual and objective statement made by the Responsible
Party.
The Alberta Climate Change Office Standard for Validation, Verification and Audit1 extends this
definition to include the document that identifies the greenhouse gas emission reduction and/or
removals and emissions offsets being claimed by the offset project over a defined period of
time.
Project: activity or activities that alter the conditions identified in the baseline scenario which
cause greenhouse gas emission reductions or greenhouse gas removal enhancements.
The GHG Assertion subject of this verification is for Carbon Credit Solutions Inc. Tillage Project
#21, which will be referred to throughout this document as “the Project”.
ISO 14064-2 defines the following parties associated with the verification:
Responsible Party: person or persons responsible for the provision of the greenhouse gas
assertion and supporting GHG information.
The Responsible Party for this verification is Carbon Credit Solutions Inc. (CCSI).
Intended User: individual or organization identified by those reporting GHG-related information
as being the one who relies on that information to make decisions.
The Intended User for this verification is the Alberta Climate Change Office (ACCO).
Verifier: competent and independent person, or persons, with the responsibility of performing
and reporting on the verification process.
The Verifier for this verification is Brightspot Climate Inc. (Brightspot Climate). The members of
the verification team are provided in section 2 of this document.
1 Standard for Validation, Verification and Audit, Version 3.0, December 2018, Alberta Climate Change Office.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
1
Introduction
This document serves to communicate information between the parties associated with the
independent verification of the Offset Project Report for the Carbon Credit Solutions Inc. Tillage Project
#21.
This document contains six sections:
1. The Introduction, which defines the principles by which this verification will be conducted;
2. The Verification, which defines the verification parameters and the GHG inventory principles that
will be tested by the verification. This section also provides information regarding the verification
team and site visit;
3. The Responsible Party Data Management and Controls, which describes the data management
system and control environment implemented by the Responsible Party;
4. Previous GHG Assertions, which describes any modifications to the original project that have
been made since the original Offset Project Plan was developed and any findings from previous
verifications for this Project;
5. The Verification Risk Assessment and Verification Procedures, which describes the risks of
potential errors, omissions or misrepresentations to the overall GHG assertion and the
verification procedures that have been developed to reduce the overall verification risk; and
6. The Sampling Plan, which lists the verification procedures that could apply sampling of the
project data, along with the sampling size, the sampling methodology and justification.
The Responsible Party developed the Project in accordance with the requirements of the Quantification
Protocol for Conservation Cropping, Version 1.0, April 2012 (the Protocol).
GHG Quantification Principles
ISO 14064-2 defines six principles that are fundamental to the fair accounting and reporting of GHG
information. The verification procedures will test that these principles have been upheld through the
Responsible Party’s inventory, accounting and reporting processes.
Section 3.2 – 3.6 of ISO 14064-2 defines these principles as follows:
Accuracy: reduce bias and uncertainty as far as practical
Completeness: include all relevant emission sources
Conservativeness: use conservative assumptions, values and procedures to ensure that GHG
emission reductions or removal enhancements are not over-estimated
Consistency: enable meaningful comparisons of reported emissions (from year to year or
between facilities or between companies)
Relevance: select GHG sources, sinks and reservoirs, data and quantification methodologies
appropriate to the needs of the intended user
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
2
Transparency: disclose sufficient and appropriate GHG information to facilitate verification and
to allow intended users to make decisions with relative confidence
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
3
Verification
Verification Principles
ISO 14064-3 defines four fundamental principles to conducting a greenhouse gas verification, namely
independence, ethical conduct, fair presentation and due professional care.
Brightspot Climate has implemented processes, including mandatory training for all verification team
members, to ensure the application of these principles for this verification.
Regarding the principle of independence, Brightspot Climate conducted an assessment of threats to
independence prior to initiating this verification. No real or perceived threats to independence were
identified. Brightspot Climate will continue to monitor for threats to independence throughout the
course of this verification. A final “Conflict of Interests Checklist” will be appended to the Verification
Statement.
Verification Parameters
The verification will be conducted according to the parameters defined in the following table:
Table 1: Verification Parameters
Level of Assurance Reasonable assurance
Objectives
• issue a verification statement on whether the GHG assertion is
without material discrepancy;
• issue a verification report that provides details of the verification
activities; and
• complete the “confirmations” activities defined in the Alberta
Climate Change Office Guidance Document2, Section 5.1.3
Criteria
• Climate Change and Emissions Management Act
• Carbon Competitiveness Incentive Regulation 255/2017 with
amendments up to and including Regulation 96/2018
• Standard for Validation, Verification and Audit, Version 3.0,
December 2018
• Standard for Greenhouse Gas Emission Offset Project Developers,
Version 2.0, July 2018
• Technical Guidance for the Assessment of Additionality, Version
1.0, May 2018
• Conservation Cropping Quantification Protocol version 1.0, April
2012
2 Standard for Validation, Verification and Audit, Version 3.0, December 2018. Alberta Climate Change Office.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
4
Scope
Project Name: Carbon Credit Solutions Inc. Tillage Project #21
Geographic Boundary: Various farms throughout Alberta within the
Parkland and Dry-Prairie eco-zones
Physical Operations: No-till cropping
Emission Sources: Soil Carbon and Nitrogen Dynamics Field
Operations
IPCC GHGs Emitted: Carbon Dioxide (CO2)
Methane (CH4)
Nitrous Oxide (N2O)
Reporting Period: January 1, 2015 – December 1, 2017
Materiality Quantitative materiality threshold is 5% of asserted greenhouse gas
emission reduction.
Preliminary Verification
Schedule
Verification Kickoff Meeting October 23, 2019
Draft Verification Plan October 28, 2019
Site Visit November 13 -17, 2017
Draft Verification Report November 25, 2019
Final Verification Report November 28, 2019
Verification Team
Aaron Schroeder, P.Eng., will be the Lead Verifier and Designated Signing Authority for this verification.
His extensive experience quantifying and verifying greenhouse gas emissions satisfies all sixteen subject
matter areas defined in the ISO 14064-3.
Michelle Stelmach, P.Ag., will conduct site visits and complete verification procedures under the
supervision of the Lead Verifier.
Desarée da Cruz will provide analytical support to the verification team through the completion of the
verification procedures and the development of the Verification Report.
Deepika Mahadevan, P.Eng., will conduct an independent peer review of the verification.
Additional information regarding the qualifications of the verification team will be provided in a
Statement of Qualifications, which will be appended to the Statement of Verification.
Site Visit Safety Requirements
Personnel conducting farm visits are required to wear steel-toed boots and exercise caution when
driving on rural roads.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
5
Responsible Party Data Management and Controls
Data Management Systems
The Credit Development Manager has the primary responsibility for collecting GHG information,
quantifying the emission reduction and completing required documentation. The Sales Support Team
assists with the collection of the information and the QA/QC Team is responsible for reviewing the files
for completeness and correctness.
The Responsible Party uses the Carbon Credit Solutions Inc. Data Management System (‘DMS”) to
manage GHG information and quantify the emission reduction. This database contains all farm and field
level data, applies data controls and quantifies the emission reduction. Carbon Credit Solutions Inc.
utilizes a paperless filing system, so all documentation, equipment photos, maps, etc. are scanned or
uploaded to their “DocSys” filing system. Table 2, below, describes the data measurement, estimation
and data storage locations for all GHG information used by the Responsible Party to produce the GHG
inventory. The final column in this table describes the data storage location and the path (intermediate
data transfer) prior to use in the GHG inventory.”
Table 2: GHG Information Data Management
Activity Data Description Measurement Type Data Storage Location / Path
Cropped Area
Crop insurance
records, land title
certificates, landlord
agreements
>> Original records
>> DocSys
>>DMS
GHG Reduction Factors Calculated from
Protocol values
>>Quantification Protocol
>> DMS
Ecozone
Logical value defined
by legal land
description
>> Alberta Agriculture and Forestry
Dataset
>> DMS
Irrigation Logical value declared
by project developer
>> DocSys
>>DMS
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
7
Previous GHG Assertions
Changes to Operations and Boundaries
There were no changes to operations and boundaries.
Findings from Previous Verifications
This project was previously verified by Ruby Canyon Engineering. Alberta Environment and Parks
Directed the Responsible Party to complete a second verification of this project.
“Based on the information collected through inquires conducted during farm visits, it was
discovered that one farm (Iron Creek Colony) had injected liquid manure on 610 acres (approx.
over 4 quarters). Some of this area was reported to CCSI but not all of it. After further inquiry, it
was determined that the farmer didn’t report the correct LLD to CCSI. CCSI was contacted and
all of this land was removed from the pool. 450 acres out of 168,338 (0.27%). The total
discrepancy is less than 0.27% of the overall asserted emission reduction.”
The verification activities will determine if these issues persist in the current reporting period.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
6
Control Environment
The Responsible Party’s Offset Project Plan (OPP) describes the processes, procedures and systems
that have been designed and implemented within their quality assurance/quality control framework. The
accuracy and completeness of the documentation of the Responsible Party’s controls will be reviewed
through the course of the verification.
The following processes, procedures and systems have been employed by the Responsible Party and
are divided into 3 Stages: Data Collection, Data Entry and QA/QC Processes. Within each of these 3
stages are automatic and manual controls to ensure the credits generated are sound.
• Data Collection – Farmers submit their information along with their Sales Agents in the
application. When all of the information is collected, including equipment photographs, crop
insurance/crop plans, etc. it is passed on to Data Entry.
• Data Entry – The information package is reviewed by Data Entry to determine if it is eligible, and
to confirm ownership of the lands. All farm lands must meet the CCSI internal standards as well
as those of the protocol to be eligible to generate credits. After they are deemed eligible and
entered into DMS and documents loaded into DocSys, a “Project Data Check” report is
generated which highlights any errors in the data entry. After these issues are addressed, the
file moves into QA/QC.
• QA/QC – The file and all supporting documents are now reviewed by QA/QC for correctness
and completeness as well as Google Earth Pro images are used to ensure correct crop areas
are being used. After this process is complete, the file is “locked down” and the farmer must
review and sign off that it is correct and complete. If there are any changes, they go through the
QA/QC process again. Only after it is signed off by the farmer and approved by a CCSI
manager will the credits be available for verification and sale.
• A new Offset Project Plan is developed for each Project. The Credit Development Manager
reviews the document for accuracy, completeness, consistency, relevance and transparency.
The OPP documents:
o Farm and field eligibility requirements
o Farm-level data collection
o Field-level data collection
o GHG emission reduction quantification methodology
o Documentation requirements and document sources
o Data management
o Data quality controls and procedures, including data collection, data entry into DMS,
data maintenance and validation, emission reduction calculation and reporting.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
8
Verification Risk Assessment and Verification Procedures
Verification risk is defined as the risk of an incorrect verification conclusion. It can be calculated as the
product of
• The Facility’s inherent risks;
• The Responsible Party’s control risks; and
• The detection risks associated with the verifier’s verification procedures.
Inherent Risk × Control Risk × Detection Risk = Verification Risk
The verifier cannot affect the inherent risk or the control risk. Therefore, to reduce the overall verification
risk and reach the agreed level of assurance (defined in the verification scope), the verifier must design
verification procedures that reduce the detection risk.
Each inherent and control risk was provided with the risk score (high/medium/low). The risk analysis of
inherent and control risks considers both the magnitude of the activity data or inventory component on
the overall GHG assertion as well as the probability that the risk will result in a discrepancy, as assessed
by the auditor.
The Verification Risk Assessment Summary on the following pages describes the following information:
Activity Data / Inventory Component: The boundary, eligibility requirement, data component or
reporting activity being evaluated.
Inherent Risk: The verifier’s evaluation of inherent risk. Inherent risks have been categorized
according to the ISO 14064-1 principles (accuracy, completeness, consistency, relevance,
transparency)
Control Risk: A description of the Responsible Party’s controls (if any controls are applicable)
and the verifier’s evaluation of control risks.
Max Detection Risk: The maximum detection risk that can be applied and still result in an overall
verification risk that meets the agreed level of assurance.
Designed Detection Risk: The detection risk of the verification procedure that the verifier intends
to complete. Note that the designed detection risk must always be equal to or lower than the
maximum detection risk.
Verification risk: the product of the inherent, control and (designed) detection risk, as defined in
the equation above.
Important note: The verification strategy for this verification is to use substantive tests instead of control
tests wherever possible. Substantive tests are designed to focus on directly testing activity data or
inventory components and their associated inherent risks. Control tests are designed to focus on
testing the Responsible Party’s controls and if the test is successful, relying on the Responsible Party’s
control. Therefore, control tests indirectly test activity data or inventory components.
Each verification procedure listed in the following table denotes if the procedure is a substantive or
control test.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
9
Table 3: Verification Risk Assessment Summary
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
PROTOCOL APPLICABILITY REQUIREMENTS
Annual crops See “Field Level Eligibility”
Disturbance levels See “Field Level Eligibility”
Reversal events Completeness – Low Farm operators may not report all reversal events.
Control: Carbon Credit Solutions interviews farmers to determine if reversal events have occurred.
Control risk: Interviews may not have identified reversal events (low risk).
High Medium Control test – Interview farm operators during farm visits to determine if reversals have occurred over the 2015-2017 crop year.
Low
Ownership See “Field Level Eligibility”
Irrigation, manure incorporation, reseeding
See “Field Level Eligibility”
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
10
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
QUANTIFICATION DATA
Cropped area Accuracy – Low Control: The land area claimed by the farm operator is compared against land titles and aerial images.
Control risk: control may not be applied (low risk).
High High Substantive test (sampled) - Compare quantities shown in DMS to aerial images (Google Earth).
Low
GHG reduction factors
Accuracy – High Control: DMS applies the GHG reduction factor based on the ecozone determined by DMS.
Control risk: There may be an error in the DMS ecozone algorithm (low risk).
Low Low Substantive test – Recalculate GHG reduction factors using values in the Protocol and compare to factors applied in DMS.
Medium
Ecozone Accuracy – Medium
Control: DMS applies the ecozone.
Control risk: There may be an error in the DMS ecozone algorithm (low risk).
High Low Substantive test – Compare all legal land descriptions in the aggregated Project to the Alberta Agriculture and Forestry ecozone database.
Low
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
11
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
FARM LEVEL ELIGIBILITY AND DOCUMENTATION
Aggregator / Farm Operator contract
Completeness – Medium
Missing contracts
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that aggregator/farm operator contracts have been executed and uploaded on DMS/DocSys.
Low
FIELD LEVEL ELIGIBILITY AND DOCUMENTATION
Ownership Completeness – Medium Contracts may be missing
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that the land title certificates are current and correspond with the lands included in the Project.
Low
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
12
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
Farm Operator / Landowner contract
Completeness – Medium
Contracts may be missing
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that farm operator/landlord contracts have been executed and the acres are within the limits of the land title certificates.
Low
Annual crops – farm records
Accuracy – Low Completeness – Medium
Potential errors in automated data management processes or manual entries
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that farm records indicate an annual crop was grown on land in sample of aggregated assertion.
Low
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
13
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
Annual crops – supporting records approved by a Professional Agrologist
Completeness – Medium
Approval of supporting records by a Professional Agrologist may be missing
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Confirm that farm records indicate an annual crop was grown on land in sample of aggregated assertion.
Low
Disturbance – farm records (including manure incorporation and reseeding events)
Completeness – High
Farm records may not completely represent the disturbance events.
Control: CCSI Sales Agents interview farmers to confirm information provided by farmers is accurate and complete.
Control risk: Interview may fail to identify or record disturbance events, (medium risk)
High High Controls test – Interview farm operators with a series of questions during farm visits to determine if all disturbances that occur on the farm have been recorded in DMS. These questions include both typical and atypical farm activities that may constitute a disturbance event.
Low
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
14
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
Discretionary tillage –disclosure
Completeness – Low
Farm records may not completely represent discretionary tillage events.
Control: CCSI Sales Agents interview farmers to confirm information provided by farmers is accurate and complete.
Control risk: Interview may fail to identify or record discretionary tillage. (medium risk)
High Medium Substantive test (sampled) – Interview farm operators regarding discretionary tillage during farm visits.
Low
Seeding equipment – record and photographs of equipment used
Accuracy – Medium Completeness – Medium
Photographs may not be on file or may not clearly illustrate opener width and spacing
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (medium risk).
High High Substantive test (sampled) – Compare equipment photos in the DMS/DocSys to observations made during farm visits. Also compare the measurements of opener width and shank spacing made during farm visits to the values recorded in the DMS.
Low
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
15
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
Irrigation – aerial images and additional farm records approved by a Professional Agrologist
Accuracy – Low Completeness – Low
Aerial images may not clearly indicate that irrigation occurred on land. Secondary documentation may not be on file.
Control: The Credit Development Manager reviews each farm file for completeness.
Control risk: The Credit Development Manager may not complete the file review (low risk).
Low Low Substantive test (sampled) – review aerial images to confirm that fields appear to have been irrigated. Review secondary documentation to confirm irrigation.
Low
EMISSION REDUCTION QUANTIFICATION
Application of the approved quantification protocol
Accuracy (high)
The project developer may not have implemented approved quantification methodologies or applied additional methodologies.
Control: Responsible Party has developed an Offset Project Plan that is intended to conform to the requirements of the approved quantification protocol.
Control Risk: The protocol requirements may not have been implemented correctly (medium)
Low Low Controls test: compare the methodologies described in the Responsible Party’s Offset Project Plan to the methodologies described in the approved quantification protocol.
Low
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
16
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
Substantive test: Recalculate the emission reduction using original metered data and methods described in the approved quantification protocol.
Low
Quantification of emission reduction
Accuracy (high)
Emission reduction calculation may contain arithmetic errors.
The Responsible Party does not have a control specifically designed to address this inherent risk.
Low Low Substantive test: Recalculate the emission reduction using original metered data.
Low
DATA INTEGRITY
Activity data and emission factor data integrity
Accuracy (high)
Data may not have been accurately transferred between electronic systems and calculation sheets.
Control: The Responsible Party uses electronic data transfers whenever possible to maintain data integrity.
Control Risk: Electronic data transfers may result in errors or may not be available for all data (medium).
Low Low Controls test: Analyze all metered data for abnormal data (zeros, missing data, values outside range).
Medium
Substantive test: Recalculate the complete emission reduction using original data.
Medium
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
17
Activity Data / Inventory Component
Inherent Risk Control Risk Max Detection Risk
Designed Detection Risk
Description of Verification Procedure
Verification Risk
Transcription of final emission reduction into Offset Project Report
Accuracy (high)
Final emission reduction may not have been transcribed accurately from calculation spreadsheets into the Offset Project Report.
The Responsible Party does not have a control specifically designed to address this inherent risk.
Low Low Substantive test: compare the final emission reduction quantity reported by the Responsible Party to the quantity reported in the Offset Project Report. Also, compare these quantities to the recalculated quantity in previous verification procedures.
Medium
Sampling Plan
The verification procedures that could apply sampling of the project data are listed in the following table.
The sampling size, the sampling methodology and their respective justifications are also described in the following table.
Table 4: Sampling Plan
Activity Data /
Inventory
Component
Detection
Risk
Design
Description of Verification
Procedure
Sampling Methodology and
Justification
Sample Size
Land title certificate Medium Substantive test (sampled) –
Confirm that land title certificates
are uploaded on the Carbon Credit
Solutions data management
system.
Suffient sample to establish 90%
confidence level, 5% confidence
interval; appropriate for the defined
Detection Risk.
Random sampling; discrepancies
are normally distributed.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
18
Activity Data /
Inventory
Component
Detection
Risk
Design
Description of Verification
Procedure
Sampling Methodology and
Justification
Sample Size
Farm Operator /
Landowner
contract
Medium Substantive test (sampled) –
Confirm that farm operator/landlord
contracts have been executed and
uploaded on the Carbon Credits
Solution data management system.
Suffient sample to establish 90%
confidence level, 5% confidence
interval; appropriate for the defined
Detection Risk.
Random sampling; discrepancies
are normally distributed.
Annual crops –
farm records and
supporting records
approved by a
Professional
Agrologist
Medium Substantive test (sampled) –
Confirm that farm records indicate
an annual crop was grown on land
in sample of aggregated assertion.
Suffient sample to establish 90%
confidence level, 5% confidence
interval; appropriate for the defined
Detection Risk.
Random sampling; discrepancies
are normally distributed.
Discretionary tillage
–disclosure
High Substantive test (sampled) –
Interview farm operators regarding
discretionary tillage during farm
visits.
Total farms required to achieve
approximately 7% of the
aggregated assertion; appropriate
for the defined Detection Risk.
Random sampling; discrepancies
are normally distributed.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
19
Activity Data /
Inventory
Component
Detection
Risk
Design
Description of Verification
Procedure
Sampling Methodology and
Justification
Sample Size
Seeding equipment
and soil
disturbance
equipment –
record and
photographs of
equipment used
Low Substantive test (sampled) –
Compare equipment photos in the
Carbon Credit Solutions data
management system to
observations made during farm
visits. Also compare the
measurements of opener width
and shank spacing made during
farm visits to the values recorded in
the Carbon Credit Solutions data
management system.
Suffient sample to establish 90%
confidence level, 5% confidence
interval; appropriate for the defined
Detection Risk.
Random sampling; discrepancies
are normally distributed.
Irrigation – aerial
images and
additional farm
records approved
by a Professional
Agrologist
High Substantive test (sampled) – review
aerial images to confirm that fields
appear to have been irrigated.
Substantive test (sampled) –
confirm that additional farm
records, beyond aerial images,
have been filed and approved by a
Professional Agrologist.
Suffient sample to establish 80%
confidence level, 10% confidence
interval. Emission reduction
associated with irrigation
constitutes less than 2% of the
total emission reduction.
Random sampling; discrepancies
are normally distributed.
Cropped area High Substantive test (sampled) -
Compare quantities shown in DMS
to aerial images (Google Earth).
Suffient sample to establish 90%
confidence level, 5% confidence
interval; appropriate for the defined
Detection Risk.
Random sampling; discrepancies
are normally distributed.
Brightspot Climate Inc. – Verification Plan Carbon Credit Solutions Inc. – Carbon Credit Solutions Inc. Tillage Project #21(6192-2129)
20
Activity Data /
Inventory
Component
Detection
Risk
Design
Description of Verification
Procedure
Sampling Methodology and
Justification
Sample Size
GHG reduction
factors
Low Substantive test – Recalculate
GHG reduction factors using
values in the Protocol and compare
to factors applied in DMS.
All Only 3 factors to review.
Ecozone Low Substantive test – Compare all
legal land descriptions in the
aggregated Project to the Alberta
Agriculture and Forestry ecozone
database.
All Reviewing all records requires the
same level of effort as reviewing a
sample of records.
Page 64 of 77
Appendix B: Statement of Qualifications
Page 65 of 77
Statement of Qualifications
Offset Report Project Name Offset Project ID
Carbon Credit Solutions, Inc. Offset Report from
January 1, 2015 – December 1, 2017
Carbon Credit SolutionsInc. Tillage Project #21 6192-2129
Reporting Company LegalName Report Type Reporting Period
to
Signature of Third Party Verifier
I, Aaron Schroeder
(Third Party Verifier), meet or exceed the qualifications of third-party verifiers described in Section 29 of the Carbon Competitiveness Incentive Regulation.
Verifying Company Name
Brightspot Climate Inc. Per: Aaron Schroeder
Signature of Third Party Verifier Date:
Training Received Under ISO 14064 Part 3
• Greenhouse Gas Verification – ISO 14064-3, Canadian Standards Association, 2012 • Instructor – Greenhouse Gas Verification – ISO 14064-3, University of Toronto, 2015 – 2018
First Name Last Name
Aaron Schroeder
Professional Designation E-mail Address Phone Number
Professional Engineer [email protected] (604) 353-0264
Lead Verifier
� Same as third party verifier??
First Name Last Name Professional Designation E-mail Address Phone Number Training Received Under ISO 14064 Part 3
December 19, 2019
Page 66 of 77
Peer Reviewer First Name Last Name Deepika Mahadevan E-mail Address Phone Number [email protected] (647) 633-8310 Training Received Under ISO 14064 Part 3
• Greenhouse Gas Verification – ISO 14064-3, Canadian Standards Association, 2012
Page 67 of 77
Appendix C: Findings and Issues
Page 68 of 77
Table 8: Detailed Findings and Issues Log
Number the issue with the year and provide a unique # for the issue. If the issue resolved during the verification, indicate that in the resolution column. If the issue is not resolved during the verification, or if the issue was material (whether resolved or not) record it as a finding in Table 2 and provide a cross reference to the finding # in the resolution column. Describe the issues investigated. State the verification criteria that are not met. Provide a description of how it is not met and provide the evidence. Indicate the Source Category (for facilities) or the Source/Sink (for offsets). Indicate if the finding is an understatement or overstatement. Summarize information between verifier and client. Provide a conclusion including % discrepancy, if applicable.
Item (YR-##)
Description of the Issues Investigated During the Verification
Summary of information exchanged between Verifier and Responsible Party
Resolution Conclusion
YR-##
17-01 The protocol allows for up to 10% (16 acres) per quarter section to apply discretionary tillage as part of the no-till farming practice.
One farm had recorded 40 acres of discretionary tillage on one quarter section on his application. The Responsible Party did not remove this land from their DMS.
We determined through further investigation that this discrepancy occurred due to a transcription error between the farmer’s application sheet and the DMS. The Responsible Party’s controls failed to detect this error.
Based on our observations and understanding of the controls in the DMS, we found that this error is unlikely to recur frequently.
The practice of discretionary tillage is not common beyond the 10% that the protocol allows. However, in this circumstance, it was missed by the Responsible Party.
Unresolved Immaterial overstatement
Page 69 of 77
Appendix D: Statement of Verification
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 70 of 77
Statement of Verification Associated SGER Submission
Offset Project Protocol Project ID #
Carbon Credit Solutions Inc. Tillage Project #21
Conservation Cropping Quantification Protocol version 1.0, April 2012 6192-2129
Project Developer Serial Range Start Report Period
Carbon Credit Solutions, Inc. N.A.
January 1, 2015 – December 1, 2017
Serial Range End
N.A.
Statement of Verification
GHG Assertion
Value Units
Total Baseline Emissions 168,338 tonnes CO2e
Total Project Emissions 0 tonnes CO2e
Other N/A tonnes CO2e
Net Reductions 168,338 tonnes CO2e
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 71 of 77
Statement of Assertion
The Responsible Party’s GHG Assertion is comprised of the Offset Project Plan, Offset Project Report and supporting documentation.
The GHG Assertion covers the reporting period January 1, 2015 – December 1, 2017 and states an emission reduction and removal claim of 168,338 tonnes CO2e over this period.
The emission reduction and removal claim consists of 2015 – 2017 vintage credits.
Responsibilities of Project Developer and Third Party Verifier
Our responsibility as the Verifier is to express an opinion as to whether the GHG Assertion is materially correct, in accordance with approved Protocol, the Carbon Competitiveness Incentive Regulation (the “Regulation”), and the Alberta Climate Change Office – Standard for Greenhouse Gas Emission Offset Project Developers, Version 2.0, July 2018.
We completed our review in accordance with the ISO 14064 Part 3: Greenhouse Gases: Specification with Guidance for the Validation and Verification of Greenhouse Gas Assertions (ISO, 2006). As such, we planned and performed our work in order to provide positive, but not absolute assurance with respect to the GHG Assertion.
The verification procedures that were performed through the course of the verification were developed based on the results of a risk assessment that was completed during the verification planning stage. These verification procedures are described in the Verification Plan. Certain verification procedures included data sampling. The sampling type, sample size and the justification for the planned sampling type and size are detailed in a Sampling Plan, which is included in the Verification Plan.
Conclusion
I believe our work provides a reasonable basis for my conclusion.
There were no unresolved misstatements in the final GHG Assertion.
Based on our review, it is my opinion at a reasonable level of assurance that the GHG Assertion is materially correct and presented fairly in accordance with the relevant criteria.
Signature of Third Party Verifier
Verifying Company Name
Brightspot Climate Inc. Per: Aaron Schroeder
Signature of Third Party Verifier
Date:
First Name Last Name
Aaron S Schroeder
December 19, 2019
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 72 of 77
Professional Designation E-mail Address
Phone Number
Professional Engineer [email protected] (604) 353-0264
Page 73 of 77
Appendix E: Conflict of Interest Checklist
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 74 of 77
Conflict of Interest Checklist
Associated SGER Submission
Offset Project Protocol
Carbon Credit Solutions Inc. Tillage Project #21
Conservation Cropping Quantification Protocol version 1.0, April 2012
Project Developer Report Type Report Period
Carbon Credit Solutions Inc. Offset Report
January 1, 2015 – December 1, 2017
Checklist Respond either "True" or "False" to each of the following statements:
1. The relationship between my firm and this reporting company poses
unacceptable threat to or compromises the impartiality of my firm.
False
2. The finances and sources of income of my firm compromise the
impartiality of my firm.
False
3. The personnel my firm has scheduled to participate in the verification
may have an actual or potential conflict of interest.
False
4. My firm participated in some manner in the development or completion
of the associated offset submission for this reporting company.
False
5. My firm provided greenhouse gas consultancy services to this reporting
company.
False
6. My firm will use personnel that have, are, or will be engaged or
previously employed by the reporting company.
False
7. My firm will outsource the Statement of Verification for the associated
offset submission.
False
8. My firm offers products or services that pose an unacceptable risk to
impartiality.
False
Important: If you have checked "True" to any of the above, you may not fulfill the "independence" requirement for third party verifiers. Please contact Alberta Environment and Parks for further instruction. If the potential conflict of interest is a sufficient threat to impartiality (perceived or actual), or cannot be effectively managed, you Third Party Verification Report will not be acceptable to Alberta Environment and Parks.
Carbon Credit Solutions Inc. Tillage Project #21, Proj ID: 6192-2129 December 2019
Page 75 of 77
Signature of Third Party Verifier
I , Aaron Schroeder (Third Party Verifier), have personally examined and am familiar
with the information contained in this Conflict-of Interest Checklist, and can demonstrate freedom from any conflict of interest related to the reporting company for which the verification was performed. I hereby warrant that the information submitted in this Conflict-of Interest Checklist is true, accurate and complete to the best of my knowledge, and that all matters affecting the validity of this Conflict-of-Interest Checklist have been fully disclosed. Impartiality shall be monitored over the duration of the verification and any identified actual or potential conflict-of-interest situations will be communicated to AEP directly.
Verifying Company Name
Brightspot Climate Inc. Per: Aaron Schroeder
Signature of Third Party Verifier Date:
First Name Last Name Aaron Schroeder Professional Designation E-mail Address Phone Number Professional Engineer [email protected] (604) 353-0264
December 19, 2019
Page 76 of 77
Appendix F: Supplemental Diagrams/Tables/Figures
Page 77 of 77
Table 9: Supporting Documentation Reviewed
File Name Description
OPP Project 21 2015-2017V1.docx Offset Project Plan for Carbon Credit Solutions Inc. Tillage Project #21.
OPR Project 21 2015-2017V1.docx Tillage Project #21 Offset Project Report
Electronic Files Reviewed Processes and procedures documents:
DMS database and DocSys (Application, Contract, Equipment Photos, Equipment Declaration, Rented Land Report, Satellite Review, Farmer Crop Insurance, Professional Agrologist Approvals of documentation.
Verification Data Package Project 21 2015-2017V1.xlsx
Primary Database export
Limitation of Liability
This report is intended for the responsible party and the intended user as defined in the attached verification report. The sole intention of the report is to verify the GHG assertion made by the responsible party named in the report and is not intended to provide assurance of any kind for any purpose other than for reporting under the GHG program as defined in the scope of the attached report.
Brightspot Climate disclaims liability for use by any other party and for any other purpose.