w w w . t n b . c aA48
Metal Framing
Surface Raceway and Lighting Systems
Superstrut
MaterialSuperstrut® electrical raceway, fixture hanging channel, closure strip and accessories are manufactured from hot rolled strip steel. Standard finish for the accessories is GoldGalv®.
Design DataDeflections at various hanger rod spacings for raceway channels based on 40 to 45 lb. per fixture.
Deflection
Channel at 10 ft. (in.) at 12 ft. (in.) at 14 ft. (in.)A1200 1/4 1/2 3/4
C12003/8 3/4
*
A1400 *
Deflection
Channel at 6 ft. (in.) at 7 ft. (in.) at 9 ft. (in.)B1200 3/8 9/16 5/8
B1400 1 1/2 *
*Not recommended for this spacing.
Electrical RacewaySuperstrut channel together with snap-in closure strip is listed by Un der-writ ers Laboratories as a surface metal race way. Other accessories listed by Underwri ters Laboratories are iden ti fied on the drawings.
Maximum Number of Wires
Wire Size AWG
Raceway
With or Without KO
A1200 A1400
B1200 B1400
C1200
E1200 H1200
A B A B A B A B14 6 10 4 6 5 10 6 10
12 6 10 3 6 4 10 6 10
10 5 8 4 6 5 8
8 4 6 3 4 4 6
6 2 3 2 2 2 3
COLUMN A: Suitable for number of wires indicated when used as a raceway. Also suitable for number of wires indicated when installed to support and sup-ply electrical fixtures when race way wiring is suitable for not less than 75°C.
By providing clearance between fixture and raceway of not less than 1/2 in., where suitable for 60°C may be used.
COLUMN B: Suitable for number of wires indicated when used as a raceway. Also suitable for number of wires indicated when installed to support electrical fixtures when clearance of not less than 1/8 in. is provided between race way and fixture and when wiring is suitable for 75°C.
Applicable ChannelsA1200 B1200
A1200-KO B1400
A1400 C1200
A1400-KO E1200
H1200
w w w . t n b . c a A49
Metal Framing
Surface Raceway and Lighting Systems
Fixture Fittings
Superstrut
802 Raceway Joiner With Reinforcing Plate
Furnished complete with nuts.
Cat. No. For Channel Wt./C lb.A802EG A Series 158
B802EG B Series 112
E802EG E Series 170
H802 H Series 182
822 Raceway Joiner & Seal
Furnished complete with 1/4 in. x 5/8 in.machine screws and AB100-1/4 nuts.
Cat. No. A (in.) For Channel Wt./C lb.A822 1-11/16 A Series 75
B822 7/8 B Series 56
A213 Inside Joiner
For A1200 Series channel.
Only available in GoldGalv® finish.
805 End Cap With Knockout
KO for 1/2 in. conduit. Furnished complete with 1/4 in. x 5/8 in. flat head machine screw and AB100-1/4 nut.
Cat. No. For Channel Wt./C lb.A805EG A Series 21
H805EG H Series 31
809 Tapped End Cap
12 ga. steel. For 3/4 in. or 1 in. conduit. Furnished complete with 1/4 in. x 5/8 in. flat head machine screw and AB100-1/4 nut.
Rod Size For Channel Wt./C lb.A809-3/4EG A Series 2
E809-3/4EG E Series 26
A853 Channel Hanger
Use hanger rod 3/8 in. or 1/2 in. Use with A, AR, B, BR or C Series single channel.
Wt./C 25 lb.
A853L Channel Hanger - Long
Long type for all Series channel.
Wt./C 48 lb.
A854 Channel Hanger
Illustration showing A854 with nut and bolt furnished to attach to fluorescent fixture.
Use with A, B, C or D Series channel.
Wt./C 34 lb.
A854L Channel Hanger - Long
Illustration showing A854L with nut and bolt furnished to attach to fluorescent fixture.
Use with E and H Series channel as well as A, B, C or D Series channel.
Wt./C 51 lb.
w w w . t n b . c aA50
44-3/4
4
4-3/4
1-1/8
1-3/81-1/2
1/32
1-3/81-1/2
1/32
1-5/8
Metal Framing
Surface Raceway and Lighting SystemsFixture Fittings
Superstrut
AB803 Cast Conduit Connector
To connect 1/2 in. or 3/4 in. conduit to raceway channel. Furnished complete with stud nuts and hex nuts. Part has removable bushing to increase size from 1/2 in. to 3/4 in.Wt./C 60 lb.
AB815 Swing Connector
Nuts and bolts to clamp to channel is included. For 1/2 in. or 3/4 in. conduit.Wt./C 95 lb.
AB885 15° Swivel
Nuts and bolts to clamp to channel included. For 1/2 in. or 3/4 in. conduit.Wt./C 25 lb.
AB867 Spacer
For use with AB866 wiring stud nuts.Wt./C 24 lb.
AB866 Wiring Stud Nut
1/2 in. Pipe threadWt./C 21 lb.
811 Stud Nut
Cat. No. For Channel Wt./C lb.811-1STR 1/4 x 1 8
811-2STR 1/4 x 1-1/4 9
812 Stud Nut
For attaching fixture to slot down channel or to slot up knockouts. Specify length. Hex nut included.
Cat. No. For Channel Wt./C lb.812-1EG 1/4 x 1 6
AB868 Fiber Retainer for Cables Until Closure Strip is In stalled
Wt./C 3 lb.
STD.PACK100
Pre-Gavanized Steel Closure StripAB844PGC AB844PGCWH White Epoxy Powder Coated
Plastic Closure StripAB844PC Color : GoldAB844PCGY Color : Grey
• When used as a raceway, channel is normally installed with the slot up. After wiring has been completed the closure strip is installed.
• For all channels.• Standard length: 10 ft.
Stainless Steel Closure StripAB844SS6CS
120 in. (10 feet)
Front viewSide view
1.7”
0.438”
Note: Strapping not included.
w w w . t n b . c a A51
Metal Framing
Surface Raceway and Lighting Systems
Kindorf® Channel Boxes and Receptacles
Superstrut
G2000
Finish - GoldGalv® Wt./C 110 lb.
G2001
Finish - GoldGalv® Wt./C 120 lb.
G2002
Finish - GoldGalv® Wt./C 120 lb.
G2003
Finish - GoldGalv® Wt./C 130 lb.
G2004
Finish - GoldGalv® Wt./C 140 lb.
G1038
Duplex Outlet
Complete unit including housing, standard DUPLEX 3-wire, 15 Amp., 125 volt, ground receptacle and cover plate.
Finish - GoldGalv® Wt./C 55 lb.
G1038A
Single Outlet
Complete unit including housing, standard SINGLE 3-wire, 15 Amp., 125 volt, ground receptacle and cover plate.
Finish - GoldGalv® Wt./C 50 lb.
G1038D
Raceway Outlet
Complete unit including housing, duplex, 3-wire, 15 amp., 277 volt-twistlock receptacle and cover plate.
Finish - GoldGalv® Wt./C 60 lb.
G1038E
Raceway Outlet
Complete unit including housing, single, 3-wire, 15 amp., 277 volt-twistlock receptacle and cover plate.
Finish - GoldGalv® Wt./C 50 lb.
G1038B Housing Only
Finish - GoldGalv® Wt./C 25 lb.
G1038C Duplex Cover Plate
Finish - GoldGalv® Wt./C 12 lb.
G1038CA Single Cover Plate
Size of opening: 1.391 diameterFinish - GoldGalv® Wt./C 14 lb.
G1038CX Blank Cover Plate
Finish - GoldGalv® Wt./C 15 lb.
w w w . t n b . c aA52
1
802
A854
A1200P
AB288
E145
ES145
Metal Framing
Surface Raceway and Lighting Systems
Kindorf® Fixture Accessories
Superstrut
G1017 Mercury Vapor Hanger
Finish - GoldGalv®
To support high or low bay mercury vapor or heavy incandescent fixtures from raceway channels. Permits plug-in connections with G-1038 raceway outlets
Used with Channel
Depth (in.)
Wt./C lb.
A-1200 4-1/4 76
G972HB1/2 Steel Fixture Hanger Adapter
Finish - GoldGalv®
The hanger adapter securely mounts the fixture hanger or box to the channel through the 1/2 in. KO in the base. No special tools are needed for installation of fittings and fixtures.
Superstrut® channels, with 1/2 in. KO’s every 6 in., hangs and feeds the fixtures thereby simplifying installation.
Wt./C 17 lb.
Electrical Appllications
2”
1-1/8” dia. hole = 3/4” KO
4-21/64”3-13/64”
1-11/16”
A-1200
AB844 Closure Strip
G-972-1¼2Nipple
G-972-HB-1/2 & G-972-HB-3/4Fixture Hanger
Adapter
Fixture Hanger
Fixture Box and Fixture
w w w . t n b . c a A53
A853
AB803
AB885
804
AB866
811
AB844
G1038D
H104805
A853
A854
822
Metal Framing
Surface Raceway and Lighting Systems
Electrical Appllications
Superstrut
w w w . t n b . c aA54
802
A1200S
A854
E145
G1038D
G2003
G2004
A853
A854
AB844
Metal Framing
Surface Raceway and Lighting Systems
Electrical Appllications
Superstrut