Space Engineering Institute (SEI)Space Based Solar Power
Space Engineering Research CenterTexas Engineering Experiment Station, Texas A&M University
By: Bryan Babbitt, Nate Broughton, Will Dixon, Stephanie Hasskarl, Travis LaCour, Veronica Medrano, Joseph Noska, and Mindy Watts
NASA Mentor: Dr. G. D. ArndtTAMU Mentor: Dr. Frank Little
Project Goal
• Develop a design for a sandwich solar power satellite module with retrodirective wireless power transmission system for inclusion in Japanese LEO to earth solar power satellite demonstration
• Demonstrate software-controlled retrodirective wireless power transmission system
Module System Sandwich Design
Antenna Array
Photovoltaic Cells
•Energy Storage & Power Conversion•Retrodirective Control logic•Thermal Management
Fall 2009 Goals
• Perform case studies for the preliminary design concept with software tools such as Satellite Tool Kit and Thermal Desktop
• Determine hardware components for:– Solar energy collection– Power system– Transmission system– Antenna
STK / Photovoltaic Cells• Chose 35° angle of inclination circular orbit, based on orbits of
other Japanese satellites of similar size.• Chose a single crystal Si photovoltaic cell that has an efficiency
of 17%• We modeled the top surface of our satellite ( 1 m^2) at this
orbit and found:– Found that the average energy acquired for every month is 126X10^6
Joules — ~3X10^6 Joules per test transmission
• Determined experiment dates and times for beaming to College Station – Satellite passes within 45° of normal– Maximum transmission length of 170 seconds– Eclipse requirement limits transmission times, but is still feasible.
STK Image of Reception Cones
Power Transmission and Antenna
• Power Transmission– Determined a 40 km reception area required to achieve a beam coupling
efficiency of 90% – Estimated a transmitting power of 2kW necessary for minimum ground
pattern detection signal of 0.1nW– Identified hardware components for transmitter subsytem
• Microstrip Patch Antenna– Maximum 450 element phased array– Capable of achieving 2kW transmitting power– Required area of elements is small enough to fit in the allowable area of
3/4 m^2 without the possibility of inducing side lobes– Polarization and power handling capability meets SPS requirements– Inexpensive and uncomplicated to manufacture
Transmitting Antenna•Corporate Feeding
Employs uniform amplification and phase shift to a 3x3 element subarray •5880 Duroid Substrate and copper rectangular patches
Silicon Solar Array
Saft MPS176065
Li-ion Battery
Misc. Components of Retro Directive
Control and Housekeeping
Power Transmission System (Solid
State Amplifiers)
Terma Array Power
Regulation Module
Terma Battery C/D Regulation
Module
IRF E-Series DC-DC
Converter
28V Bus
Satellite Bus and Electronics
•The Saft MPS battery has a nominal energy of 480 Wh and an end of charge voltage of 32.8 V•DC-DC Converter, Regulation modules and battery have an efficiency of over 90%•Less than 6 Kg. for DC-DC Converter, Regulation modules and battery
Thermal Management
• Goal is to ensure that equipment is kept within designated temperature ranges (-20°C to 60°)
• Hot Case: Transmitting produces about 3 kW of heat– Plan to transmit during eclipse– Use loop heat pipes to transfer heat to radiator on bottom of satellite– Use thermal storage with phase change material
• Cold Case: Shaded by earth and not transmitting– Use thermal energy stored from transmission time to heat electronics – Use resistance heaters if additional heat is needed
Thermal Desktop Image
Transient Temperature Response
Heating of electronics during transmission with assumed mass of 20 kg and assumed radiator size of 0.25 m2.
Cooling of electronics after transmission, with assumed mass of 20 kg and assumed radiator size of 0.25m2.
Retrodirective System• Hardware Retrodirective Control Method
– Researched control technique that uses a 2nd harmonic transceiver to double and conjugate received pilot beam– Requires that a receiving antenna be nested within the transmitting antenna array – Requires a pilot signal of 2.9 GHz
• Software Retrodirective Control Method – Use logic to establish conjugate phase of received pilot signal– Use logic to implement phase conjugation and redirect transmit beam in the direction of the received pilot signal. – Preliminary design and required components have been identified– Method requires same antenna configuration as hardware method– Frequencies of pilot signal less limited
Retrodirective System
Summary• Determined solar energy data for a 35° inclination orbit• Determined power level of 2 kW required for transmitting
detectable signal• Plan to transmit during eclipse to meet thermal
requirements• Selected hardware components that meet power
requirements• Developed design of electronics hardware • Developed preliminary design of satellite, but final design is
to be determined with further analysis• Gained knowledge of Thermal Desktop and can model
accurately thermal behavior of satellite when it is updated.
Plan for Spring 2010
• Integrate systems into a unified design• Conduct trade studies for different system
configurations.• Maximize photovoltaic and antenna area
while allowing sufficient space for radiators.• Perform test demonstration of retrodirective
system