Sign By-law
guide
BuSineSS identification SignS
SignS that identify a BuSineSS
Signs in Vancouver are administered depending on their location on private property, public right-of-ways, or parks. This guide summarizes the rules and permitting process for private property only, which is regulated by the Sign By-law.
The Sign By-law Guide is a companion to the Sign By-law. It is not a substitute for the Sign By-law. The Sign By-law always takes precedence over this guide if there are any discrepancies.
aBout the Sign By-law
Signs on City sidewalks, roads, boulevards (including sandwich boards and posters on light posts) are regulated by the Traffic and Streets By-law and are managed by Engineering Services.
Signs on City Parks are managed by the Park Board, through authority granted by the Vancouver Charter.
The Sign By-law is a set of rules for signs on private property.
ParkStreet, Boulevard or
Sidewalk
Private ProPerty
Sign By-law Guide 1
4TH AVE.
DU
NB
AR
ST.
MA
CD
ON
AL
D S
T. AR
BU
TU
S S
T.
GR
AN
VIL
LE
ST.
CA
MB
IE S
T.
MA
IN S
T.
FR
AS
ER
ST.
KN
IGH
T S
T.
VIC
TO
RIA
DR
.
NA
NA
IMO
ST.
CO
MM
ER
CIA
L D
R.
1ST AVE.
HASTINGS ST.
RE
NF
RE
W S
T.
AR
GY
LE
ST.
54TH AVE.
29TH AVE.
GRANDVIEW HWY.
SE MARINE DR.
RU
PE
RT
ST.
BO
UN
DA
RY
RD
.
KINGSWAY
12TH AVE
16TH AVE
KING EDWARD AVE.
33RD AVE.
41ST AVE.
49TH AVE.
57TH AVE.
70TH AVE.
SW M
AR
INE D
R.
BROADWAY
BURRARD
ST.
GEO
RGIA
ST.
finding your Sign diStrict
The Sign By-law organizes similar areas of the city into Sign Districts, and these correspond to groups of Zoning Districts. A property’s zoning district can be found using the City of Vancouver map system called VanMap, available here: http://vanmapp.vancouver.ca/pubvanmap_net/default.aspx
Standard zoning districts are assigned to sign districts in Part 7 of the Sign By-law.
If the zoning district is not listed on the chart in Part 7, it may have a unique zoning called a Comprehensive Development (CD-1) district. The Sign By-law assigns CD-1 district sign regulations as follows:
CD-1 District Assigned Sign District
CD-1 districts listed on general Schedule A
Part 9 - Commercial, Mixed Use and Industrial Sign District
CD-1 districts listed in general Schedule B
One of: Part 10 - Chinatown and Gastown Historic Sign DistrictPart 11 - West End Sign DistrictPart 12 - Granville Street Sign DistrictPart 13 - Rogers Arena Sign DistrictPart 14 - International Village Sign District
CD-1 districts not listed on any general Schedules
Part 8 - Residential Sign District
legend
Residential Sign District (Part 8)
Commercial Sign District (Part 9)
Chinatown & Gastown Historic Sign District (Part 10)
West End Sign District (Part 11)
Granville Street Sign District (Part 12)
Rogers Arena Sign District (Part 13)
International Village Sign District (Part 14)
Park (Under Park Board management)
If residential use (Part 8), If commercial use (Part 9)
Sign By-law Guide2
Signs form part of the overall appearance of businesses within Vancouver neighbourhoods. Signage assists customers in reaching their destination, and reinforces business identities. The City of Vancouver supports commercial activity by allowing appropriate business identification and wayfinding signs, and discouraging sign proliferation and visual clutter to ensure the effectiveness of signs.
Successful business identification signs are:
Contextual
Signs contribute to a cohesive commercial identity. Signs that are similar to the pattern established by nearby businesses or by the district are encouraged. Signs should integrate well with into a building’s architecture and not block architectural features. This can be achieved, for instance, by adding signs on an existing weather protection awning or canopy, or on blank sections of building walls.
Innovative
Creative sign placement, colours and materials add vibrancy to an area. Expressing business identity through unique sign designs add architectural character and interest. High quality materials that are durable and easily maintained should be used.
Clear
Signs should be focused, clear, and easy to read. This can be achieved through appropriately scaled lettering, simple graphics, channel letters, and colour contrast. Minimizing the overall number of signs on a building will help to focus attention on business signage. Using lighting that is focused and minimal will reduce impacts on nearby residents.
Well Located
Careful sign placement improves wayfinding and creates a pleasant experience for pedestrians. Allow for appropriate space underneath and around signs to maintain safe, clear travel paths for patrons. Views into businesses should be maintained by minimizing obstruction of windows. Locate signs in visible areas, near entry doors to direct patrons toward the business.
BuSineSS identification
deSign conSiderationS
Sign By-law Guide 3
Copy is the letters, logos and graphics that make up the message on a sign. The photos on the adjacent page illustrate the different types of copy described in the Sign By-law.
When considering signage needs for a premise, use a type of copy that compliments a building’s architecture. For instance, individual channel letters may minimize obstruction of architectural features and allow for clear business identification.
coPy tyPeS
Individual letters or numbers
Logos
Sign with a border, frame or background
Electronic message sign Electronic static image sign Electronic video sign
Sign By-law Guide4
SIGN
SIGN
SIGNFrontage
Minimum clearance: 2.75 m (9 ft)
Vertical dimension Sign area ( )
Frontage
Frontage
Height
Copy area ( )
SIGN
Width
key terminology
For more information on key terminology, see Section 1.3 of the Sign By-law.
Sign By-law Guide 5
Sign diStrictS
reSidential Sign diStrict
commercial, mixed uSe and induStrial Sign diStrict
chinatown and gaStown hiStoric Sign diStrict
The Residential Sign District allows signs that are complimentary to residential city neighbourhoods, including signs for neighbourhood grocery stores. Regulations for the Residential Sign District can be found in Part 8 of the Sign By-law.
The Commercial, Mixed Use and Industrial Sign District promotes business identification and wayfinding for many commercial and industrial properties in the city. Regulations for the Commercial, Mixed Use and Industrial Sign District can be found in Part 9 of the Sign By-law.
The Chinatown and Gastown Historic Sign District enhances the authentic historic character of Chinatown and Gastown. Regulations for the Chinatown and Gastown Historic Sign District can be found in Part 10 of the Sign By-law.
Private property is assigned to one of seven sign districts in the Sign By-law. There are two standard sign districts that apply to the majority of the city: the Residential Sign District and the Commercial, Mixed Use and Industrial Sign District. Five additional sign districts apply to unique areas of the city.
Sign By-law Guide6
weSt end Sign diStrict
granville Street Sign diStrict
rogerS arena Sign diStrict
international village Sign diStrict
The West End Sign District integrates signage complementary to the residential character of the West End.Regulations for the West End Sign District can be found in Part 11 of the Sign By-law.
The Granville Street Sign District reflects the historic retail and entertainment role of Granville Street by encouraging colourful, vibrant, and neon signage. Regulations for the Granville Street Sign District can be found in Part 12 of the Sign By-law.
The Rogers Arena Sign District supports recreational and cultural activities through recognition of event sponsors, larger logos and wayfinding signs. Regulations for the Rogers Arena Sign District can be found in Part 13 of the Sign By-law.
The International Village Sign District encourages innovative, colourful, prominent signage to enhance the architecture of the Village Marketplace area. Regulations for the International Village Sign District can be found in Part 14 of the Sign By-law.
Sign By-law Guide 7
Sign tyPeS
1 Banner sign, p.22
2 Under awning sign, p. 14
3 Second storey fascia sign, p. 26
5 Awning sign, p. 12
4 Window sign, p. 38
There are a number of sign types that can be used for business identification.
Sign types are described in the definitions found in Section 1.3 in the Sign By-law and are illustrated generally here.
• Electronic message sign, p. 38
SIGN
SIGN
SIGNSIGN
1
2
3
4
56
7
8
9
10
11
12
13
14
Sign By-law Guide8
SIGN
SIGN
SIGNSIGN
1
2
3
4
56
7
8
9
10
11
12
13
14
6 First storey fascia signs, p. 25
10 Sign in conjunction with a mural p. 34
7 Upper level fascia sign, p. 27
11 Painted fascia sign, p. 28
12 Projecting sign, p. 32
8 Canopy sign, p. 16 13 Free-standing sign, p. 36
9 Under canopy sign, p. 2014 Mansard roof sign, p. 30
Sign By-law Guide 9
Business Identification Sign Type
Permit RequiredResidential
Sign District
Commercial, Mixed Use and Industrial Sign
District
Chinatown and Gastown Historic
Sign District
West End Sign District
Granville Street Sign District
Rogers Arena Sign District
International Village Sign District
Awning and Under Awning • • • • • • •Canopy and Under Canopy • • • • • • •
Banner • • • • • • •Fascia – First Storey • • • • • • • •
Fascia – Above First Storey • •Fascia – Second Storey • • • • • • •
Fascia – Above the Second Storey •Fascia – Painted up to 3 Storeys • •
Fascia – Upper Level • • • • •Freestanding • • • • • • • •
Freestanding - Wayfinding • •Mansard Roof • • • • •
Projecting • • • • • • •Sign in Conjunction with a Mural • • • • •
Temporary Signs • • • • • • •Window • • • • • •
Signs with Animated Copy • •Electronic Message • • • • •
Permitted SignS
On this chart, the dots indicate the types of signs that are permitted in a Sign District.
Some sign types have additional criteria such as minimum site area or zoning. Review the specific regulations in the Sign By-law for each sign type to determine if it is allowed on your property.
Illustrations from pages 12 to 38 depict regulations for signs in the Commercial, Mixed Use and Industrial Sign District. Be sure to check the Sign By-law for exact requirements on a property.
Sign By-law Guide10
Business Identification Sign Type
Permit RequiredResidential
Sign District
Commercial, Mixed Use and Industrial Sign
District
Chinatown and Gastown Historic
Sign District
West End Sign District
Granville Street Sign District
Rogers Arena Sign District
International Village Sign District
Awning and Under Awning • • • • • • •Canopy and Under Canopy • • • • • • •
Banner • • • • • • •Fascia – First Storey • • • • • • • •
Fascia – Above First Storey • •Fascia – Second Storey • • • • • • •
Fascia – Above the Second Storey •Fascia – Painted up to 3 Storeys • •
Fascia – Upper Level • • • • •Freestanding • • • • • • • •
Freestanding - Wayfinding • •Mansard Roof • • • • •
Projecting • • • • • • •Sign in Conjunction with a Mural • • • • •
Temporary Signs • • • • • • •Window • • • • • •
Signs with Animated Copy • •Electronic Message • • • • •
Sign By-law Guide 11
PERMIT REQUIRED
Awnings are light, detachable or retractable structures that provide weather protection along storefronts and businesses. Signs located on the front, side or soft fringe of an awning, or on a circular awning are called Awning Signs.
These illustrations depict regulations for Awning Signs from the Commercial, Mixed Use and Industrial Sign District.
awning SignS
Sign By-law Guide12
lo
ca
tio
nc
oP
yd
ime
nS
ion
S
Maximum copy area
Grade
Maximum copy area
Roof line
Extends no more than 0.5 m above the roof line
Maximum height
6 m
Does not extend above the window of second floor
Grade
Minimum clearance
2.75m
Sign By-law Guide 13
PERMIT REQUIRED
Awnings are light, detachable or retractable structures that provide weather protection along storefronts and businesses.
Signs located underneath an awning are Under Awning Signs. These signs are intended to be viewed by patrons on the sidewalk. They are situated perpendicular to a building and located near an entrance.
These illustrations depict regulations for Under Awning Signs from the Commercial, Mixed Use and Industrial Sign District.
under awning SignS
Sign By-law Guide14
lo
ca
tio
nd
ime
nS
ion
S
Minimum clearance
2.75m
Maximum vertical dimension
0.3m
Maximum length
1.5m
SIGNS
Grade
Sign By-law Guide 15
Canopies are permanent roof structures that provide weather protection along storefronts and businesses. Signs attached to the front, side or above a canopy are Canopy Signs.
Premises with larger frontages may have larger Canopy Signs.
These illustrations depict regulations for Canopy Signs from the Commercial, Mixed Use and Industrial Sign District.
canoPy SignS
PERMIT REQUIRED
Sign By-law Guide16
lo
ca
tio
nc
oP
yd
ime
nS
ion
S
Maximum copy area
0.6 m2 X frontage length
Frontage
Grade
Grade
Maximum beyond the front of the canopy
0.6 m
Canopy
Maximum beyond the side of the canopy
0.6 mMinimum clearance
2.75m
Sign By-law Guide 17
Frontage > 30m
dim
en
Sio
nS
Less than 20% of canopy length
Canopy length
Theatre or premises with a frontage more than 30m
Canopy length
No more than 1.2 m above the canopy face
No more than 2 m above the canopy face
Less than 20% of canopy length
Maximum vertical dimension
1 mMaximum vertical dimension
2 m
Maximum vertical dimension
3 m
Maximum vertical dimension
1.5 m
PERMIT REQUIRED
Maximum vertical dimension
1 m
Maximum
0.45 mMaximum
0.45 m
A portion of a Canopy Sign may have a larger vertical dimension.
Theatre or premises with longer frontage may have a larger sign.
Sign By-law Guide18
Sign By-law Guide 19
Canopies are permanent roof structures that provide weather protection along storefronts and businesses. Signs located perpendicular to a building and under a canopy are called Under Canopy Signs. Under Canopy Signs direct pedestrians along sidewalks to a premises entry. Under Canopy Signs should be located near the front door of a business.
These illustrations depict regulations for Under Canopy Signs from the Commercial, Mixed Use and Industrial Sign District.
under canoPy SignS
PERMIT REQUIRED
Sign By-law Guide20
lo
ca
tio
nd
ime
nS
ion
S
Canopy
Canopy
Maximum vertical dimension
0.45 m
Maximum length
1.5 m
Grade
the front canopy edge
Must not project beyond
Sign By-law Guide 21
A banner is made of a light, flexible material, and is attached perpendicular to a building. In the Sign By-law, signs on a banner are called Banner Signs. These signs can be secured up to three edges and must not be illuminated. A permit is not required for this sign type.
A premises that may have one or multiple banner signs with a combined copy area that do not exceed the maximums described in Section 6.6 if the Sign By-law.
These illustrations depict regulations for Banner Signs from the Commercial, Mixed Use and Industrial Sign District.
Banner SignS
NO PERMIT REQUIRED
Sign By-law Guide22
lo
ca
tio
nc
oP
yd
ime
nS
ion
S
Perpendicular to a building face
Length
30% of copy
Maximum first-party advertising area:
2 X Length
Minimum vertical dimension:
Maximum sign area
4 m2
20% of sign area
Maximum copy area:
Sign By-law Guide 23
A fascia sign is a sign attached parallel to a building face. Regulations for fascia signs are different for signs on the first, second and upper building storeys. Larger painted signs are allowed in industrial areas.
These illustrations depict regulations for Fascia Signs from the Commercial, Mixed Use and Industrial Sign District.
faScia SignS
First Storey Fascia Sign Painted Fascia Sign
Upper Level Fascia SignSecond Storey Fascia Sign
PERMIT REQUIRED
Sign By-law Guide24
firSt Storey faScia SignSl
oc
atio
nc
oP
y
Above the first storey window or lintel
+ ≤ 0.6 m2 x frontageCopy area =
Maximum 0.75 m above the floor of the second storey if there is no window
Maximum copy area: 0.6 m2 x frontage
Maximum copy area: 40% x frontage
Does not extend above the roof line
Frontage
FrontageFrontage
Frontage
L1 L2 L3
Maximum vertical dimension
0.6 m
Maximum width2.5 m
Lane
Street
Sign facing a lane
One-storey building
Multi-storey building
Signs below the top of first storey windows
Grade
Below the second storey
Copy area may exceed 40% of the sign area if the sign contains a logo only
when painted on a wall, the sign area may be up to 4 m2
Maximum sign area ≤ 0.3 x (L1+L2+L3) ≤ 3 m2;
Fascia Sign with a borderFascia Sign with channel letters
Identifies principle occupant or building name
Vertical dimension
Width
Sign By-law Guide 25
Second Storey faScia SignSl
oc
atio
nc
oP
yd
ime
nS
ion
S
Does not extend above the roof line
Below the window sill of the third storey
Maximum 0.75 m above the floor of the third storey
One sign on either the first or second storey
Frontage
0.4 m2 x frontage
Maximum copy area:
Maximum vertical dimension
1 m
Grade
PERMIT REQUIRED
2 Storey Premises
Individual letters only
Sign By-law Guide26
uPPer level faScia SignS aBove the Second Storey l
oc
atio
nc
oP
y
Maximum copy area: 47 m2
Copy area = Width x Length
Roof line
Length
A sign more than 55 m in height must contain copy consisting of a logo only
Over 55 m in height
Grade
Grade
Is between the floor of the uppermost storey and the roof line
One sign per building face; and maximum 2 signs on the building
Two signs on adjoining building faces are more than 2 m from a common corner
2m2m
40AND
Length
Grade
Width
Sign By-law Guide 27
Painted faScia SignS on BuildingS uP to three StoreyS
lo
ca
tio
nc
oP
y
No higher than the third storey
Frontage
Painted on the wall; identifies the principal occupant or building name only
Building face area
20% x building face ( of 1st, 2nd and 3rd storey)
Maximum copy area:
PERMIT REQUIRED
For more information see section 9.14 in the Sign By-law.
Sign By-law Guide28
Sign By-law Guide 29
A mansard roof has four sloping sides. A sign attached to a mansard roof is called a Mansard Roof Sign.
These illustrations depict regulations for Mansard Roof Signs from the Commercial, Mixed Use and Industrial Sign District.
manSard roof SignS
PERMIT REQUIRED
Sign By-law Guide30
lo
ca
tio
nc
oP
yd
ime
nS
ion
S
No less than 0.3m below the roof line
Frontage
Frontage
Projects no more than 0.25 m from the roof at the base of the sign
Grade
0.6 m x frontage length
Maximum sign area:
Maximum copy area
Maximum height
8 m
Maximum vertical dimension
1.0 m
Sign By-law Guide 31
Signs that are secured perpendicular to a building wall are called Projecting Signs. These signs are intended to be viewed by patrons on the sidewalk and should be located near an entrance. Projecting signs may also be located at the corner of a building.
For this sign type, sign area varies by zoning. In the Commercial, Mixed Use, Industrial Sign District, the maximum sign area ranges from 0.075m2 to 0.30m2 per length of frontage. See Table 9.3 in the Sign Bylaw for more information.
For projecting signs located at the corner of a premise, the calculation of maximum sign area is based on the average frontage length:
(Frontage 1 + Frontage 2) = Average Frontage __________________ 2
Each premises may have one projecting sign at the first storey.
These illustrations depict regulations for Projecting Signs from the Commercial, Mixed Use and Industrial Sign District.
Projecting SignS
PERMIT REQUIRED
Sign By-law Guide32
lo
ca
tio
nc
oP
yd
ime
nS
ion
S
Sign area depends on zoning, see Sign By-law section 9.20 Copy area may exceed
40% of the sign area if the sign contains a logo only
No greater than 0.3 m between the sign and the building face
Do not extend above 21 m in height
Do not extend above the roof line
Roof line
in height or 1.8 m above the roof line
Lower of 6 m
One-storey building Multi-storey building
Maximum copy area: 40% of the sign area
Grade
Property Line
Property Line
Encroachment no more than 25% x D; maximum 3 m
D
Encroaching projecting sign- site plan view
Fro
nta
geBuilding
Street
1.8 m
6 m
Sign By-law Guide 33
A mural is a graphic or art that is typically painted or affixed to a building wall. When a sign is incorporated into a mural, this is called a Sign in Conjunction with a Mural.
Murals are reviewed and approved by the City through a development permit process. The sign portion of the mural is considered through a Sign Permit Application. This can include the name of a building, principle occupant name or logo.
These illustrations depict regulations for Signs in Conjunction with a Mural from the Commercial, Mixed Use and Industrial Sign District.
SignS in conjunction with a mural
PERMIT REQUIRED
Sign By-law Guide34
lo
ca
tio
nc
oP
y
Maximum height above grade
20m
Grade
90%Mural
Maximum sign copy area
Sign By-law Guide 35
Signs attached directly to the ground are Freestanding Signs. Freestanding signs are suited to buildings that are setback from the property line and to identify multiple tenants on a shared sign.
The allowable size and encroachment of a freestanding sign varies by zoning. See Sign By-law section 9.15 for more information.
Sites over 25,000m2 may have freestanding wayfinding signs. These are signs attached to the ground that display information or maps for wayfinding. See Sign By-law section 9.16 for more information.
These illustrations depict regulations for Free-standing Signs from the Commercial, Mixed Use and Industrial Sign District.
free-Standing SignS
PERMIT REQUIRED
Sign By-law Guide36
lo
ca
tio
nc
oP
yd
ime
nS
ion
S
Maximum copy area
Sign area depends on zoning, see Sign By-law section 9.15(d)
Property Line
1.5 m from a property line
1 m away from a building
Grade
Maximum height
8 m
Grade
Copy area may exceed 40% of the sign area, if the sign contains a logo only
Depth
Encroaches no more than 25% x D; maximum 3 m
Building
Property Line
Property Line
Encroaching free-standing sign- site plan view
Copy area= +
Grade
Street
Do not include this area where sign area is 2.75 m above
Sign By-law Guide 37
Signs located near to or on a window are Window Signs. This category of signs includes photographs, images and lifestyle graphics used to promote products or services available at a business. A permit is not required for this sign type.
As a general rule, window signs cannot be illuminated. However, a premise may locate one small illuminated electronic message sign in a window, such as an open or operating hours sign.
These illustrations depict regulations for Window Signs from the Commercial, Mixed Use and Industrial Sign District.
window SignS
NO PERMIT REQUIRED
Electronic Message Sign
Sign By-law Guide38
lo
ca
tio
nc
oP
y
Electronic message sign has a copy area no greater than 0.34 m2
OPENOPEN
SIGNS SIGNS
First storey premises
Grade
Second storey premises
Contiguous glass area =
10% of the contiguous glass area on the second storey
Maximum sign area:
30% of the contiguous glass area on the first storey
Maximum sign area:
+
Sign By-law Guide 39
The Sign By-law contains standard illumination requirements for all signs in the City, which reduce impacts on residents and maintain safe conditions on streets and sidewalks.
Most signs on private property in Vancouver may be illuminated. In certain locations, illuminated signs may be restricted near dwelling units, or may have additional operating requirements. For more information, see section 5.11 in the Sign By-law.
illumination
Projecting sign with internal illumination Projecting sign with internal illumination
Fascia sign with external illumination
Sign By-law Guide40
Shield required if externally illuminated Do not illuminate from below
Lighting source concealed under the awning
Signs within 30 m must be turned off from 11.p.m - 7.a.m
Maximum 3.0 Lux above ambient light on adjacent site or street
Residential Sign District
Dwelling Units
Sign By-law Guide 41
Most signs on private property in Vancouver require sign permits except those described in section 6 of the Sign By-law, such as Banner Signs, Window Signs, and signs displaying only a building number and street name.
The following documents are required for a complete sign permit application package:
1. Application Form
In the online Application Portal, information is added directly into online fields. A Sign Details Form, available in the Online Application Portal, is required. In person, customers fill out the City of Vancouver’s application form. This lists what documentation is required, and includes required fields for proposed sign dimensions. This form, including all dimensions, must be completed in full to be processed by staff. To assist in filling out this form, see the explanation of sign permit application form information requirements found on page 46 of this guide.
2. Sign Drawings
Copy, site plan, section and elevation drawings must identify and label the dimension measurements in metric. An example of a sign drawing package is shown on pages 44 to 45 in this guide.
3. Fees
The standard Sign Permit application fee is $294. Additional fees apply to signs that require electrical connections, a relaxation, for a billboard. For more information, consult the Sign Fee By-law. If you are applying in person, you can pay by cheque or credit card. Fees are automatically calculated in the online portal, and can be paid online by credit card.
making a Permit aPPlication
Sign By-law Guide42
4. Owners Undertaking Letter
An owners undertaking letter must be signed by the owner of the property or authorized signatory of a corporation that owns a property.
5. Supplemental documentation
Additional information may be required for certain sign proposals:
Awning Permits are required for new awning structures that include an awning signs.
Building Permits are required for signs over 200lbs, freestanding signs, projecting signs, and above the second storey of a building.
Electrical Permits are required for illuminated signs.
Heritage Alteration Permits are required for properties on the Vancouver Heritage Register.
Where to Submit an Application
Sign permit applications can be submitted:
Online, by registering for an online account and submitting an application.
In person, by submitting the application to the Development and Building Services Centre, located at:
Ground floor, 515 West 10th Avenue, Vancouver, BC
After recieving a permit and beginning installation call 3-1-1 (604-873-7000) for an inspection.
Sign By-law Guide 43
3.05 m (10 ft)
1.52 m (5 ft)
32.31 m (106 ft) Site width
20.12 m (66 ft) Building width 12.19 m (40 ft) Parking area
Cam
bie
St
0.61 m (2 ft)
0.37 m (1.2 ft)
0.37 m (1.2 ft)
Property Line
W 88th Ave
City Sidewalk
Curb
18.29 m (60 ft) Building and site depth
ADJACENT TENANT
ADJACENT TENANT
1213 W 88th AVE 1217 W 88th AVE1215 W 88th AVE
6.71 m (22 ft) frontage
1.83 m (6 ft)
3.05m (10 ft)
1.83m (6 ft)
0.24m (0.8 ft) sign box-3.05 m (10 ft) long
Proposed Sign
SIGN COPY DRAWING
Scale - 1:10
SITE PLAN FLOOR PLAN DRAWING
Scale - 1:200
SamPle drawing Package
Sign By-law Guide44
SECOND FLOOR TENANT
Store - 6.71m (22ft) Frontage
Top of Parapet Wall
Roof Line(bottom of parapet wall)
(first storey floor line)
Top of Proposed Sign
Second Storey Floor Line
Bottom of Proposed Sign
Grade
1.83m (6ft) 1.83m (6ft)3.05m (10ft)
0.61m (2ft)
2.93m (9.6ft)
0.3m (1ft)
0.3m (1ft)
2.74m (9ft)
Top of Parapet Wall
Roof Line(bottom of parapet wall)
(first storey floor line)
Top of Proposed Sign
Second Storey Floor Line
Bottom of Proposed Sign
Grade
0.61m (2ft)
2.93m (9.6ft)
0.3m (1ft)
0.3m (1ft)
2.74m (9ft)
0.2m (8in)
1.83m (6ft)Curb
ELEVATION DRAWING
Scale - 1:40
PARTIAL SECTION DRAWING AT SIGN LOCATION
Scale - 1:40
Sign By-law Guide 45
Drawings identify the location and label dimensions of: Proposed: Sign Bylaw allowance for this premises:Proposed sign locationLocation of grade (ground)Clearance dimension (height from grade to bottom of sign)Premises frontage length dimensionBuilding storey floor lines locationDistance from the proposed sign to the nearest tenant (dimension)
For signs attached to a building, identify:Location of all windows and doorsRoof/parapet line locationHeight of sign and support structure above roof (dimension)Projection from building face (dimension)
Sign Structure and Materials - Required InformationFrame MaterialCross BracingSign Face MaterialMethod of AttachmentSign Weight Structural Drawings are required for: signs over 200lbs, freestanding signs, signs above the second storey.
Two signed sealed structural drawing sets are attachedOne copy of signed sealed B1/B2 Letters of AssuranceOne copy of signed sealed Structural Concept Review Letter
Forms are available at: http://vancouver.ca/home-property-development/application-forms-and-checklists.aspx
Sign By-law Compliance and RelaxationsDoes the proposed sign comply with the Sign By-law?Is a relaxation under Part 15 of the Sign By-law being requested? Identify the reason for the relaxation request:
Unnecessary hardship New TechnologyHeritage property, historic area, historic sign Special EventA rationale letter explaining the request and how the proposal meets the parameters of Part 15 of the Sign By-law is attached.
Information is available in the Sign By-law Relaxation and Sign By-law Amendment Guide at:http://vancouver.ca/your-government/sign-bylaw.aspx Electrical -
Required for Illuminated SignsType of IlluminationElectrical contractor must be named on the application for a sign permit to do interconnection of electrical components of a sign, if the sign contractor is not a registeredelectrical contractor. A separate electrical permit is required for a power supply connection to a permenantely connected sign. This permit shall be obtained by an electricalcontractor under provisions of the City Electrical By-Law (Bulletin 2005-006-EL).Electrical Contractor - NameAttachment “A” to Bulletin 2005-006-EL/AD, Letter of Commitment is attached
The form is available at: http://bulletins.vancouver.ca/2005/2005-006.pdf
Sign Company, Manufacturer, Owner and Tenant Information - RequiredSign Contractor - NameAddress, City, Postal CodePhoneEmailProperty Owner - NameAddress, City, Postal CodePhoneEmail
Owners undertaking letter is attachedA form letter is available at: http://vancouver.ca/files/cov/schedule-e1-owners-undertaking-letter.pdf
Tenant - NameAddress, City, Postal CodePhoneEmail
Applicant Signature - Required InformationName of Applicant:Applicant is:
Sign Company OwnerTenant Other (explain):
As owner or owner's agent, I have verified that the information contained within this document and associated applications and plans is correct and that I am acting with theowner's full knowledge and permission. In consideration of the granting of a Sign Permit I agree to comply with all applicable requirements of the Sign By-law, Zoning andDevelopment By-law, Building By-law and Encroachment By-law, and all other applicable laws, by-laws and regulations, and to indemnify and save harmless the City of Vancouver and its officials, officers, employees and agents ("City Personnel") against all claims, liabilities, judgements, costs and expenses which may accrue against the City ofVancouver in consequence of and incidental to the permissions to place, erect or display the sign. I further certify that the sign and its supports meet the constructionrequirements in the Sign Bylaw and the Building By-law.Signature of Applicant (Authorized Officer of Company):
Office Use OnlyApplication Number
Date Application was ReceivedPermit Fee Amount
Electrical Fee AmountStructural Fee Amount
Other Fee AmountTotal Fee
Receipt Number
(2)
Partial Section Drawings at the Sign Location - Required Information
No
No
3 m 2.75 m
exPlanation of Sign Permit aPPlication form
information requirementS
Identify the exact dimensions
Identify the maximum or minimum allowed in the Sign By-law
Check the box to indicate that the required document is in your application package
Sign By-law Guide46
Sign By-law Guide 47
City Hall 453 West 12th Ave Vancouver, BC V5Y 1V4
3-1-1
604-873-7000