PUMPS
32
“To be the chosen supplier for adhesive and sealant application systems. Based
on Quality, Reliability, and Performance.”Grunfeld Mission Statement
1,000,000
0
500,000
100,000
50,000
Visc
osity
(cPs
)
37.85 75.70 113.55
Putty, Caulking,
Plastisols
Peanut Butter
Toothpaste
Ketchup
Water
Flow (LPM)
1
2
3
2
1
32-Ball Pumps
4-Ball Pumps
Chop-Check Pumps
54
LPMflow rate
fluid viscosity
reliableoutput pressurepumpprocess
Transfer Pump Selection Made Simple
With a Grunfeld pump system you can be assured of getting reliable equipment with minium effort on your part.
The four factors that need to be taken into consideration are as follows:
Type of Fluid, Viscosity or Thickness, Required Flow Rate, Required Output Pressure.
Knowing fluid viscosity and flow rates makes it easier to find the right pump for your application. However, if you’re not sure then give us a call and one of the team will be
happy to advise you.
76
Pumping FundamentalsThe versatility of piston pumps is unmatched as they are used in a seemingly endless array of applications and pumping solutions. With this in mind, it is important to remember these basic pumping fundamentals to help ensure the right product is selected for your unique application.
Piston Pump Applications
Piston pumps are used in a wide variety of fluid handling applications. The majority of these can be broken down into four different categories:
Transfer
Moving a low-to-medium viscosity fluid from one location to another. 2-ball and 4-ball style pumps are the most frequently used in transfer applications.
Extrusion
Involves using a piston pump to apply medium-to-high viscosity materials. Typical extrusion applications require accessories like rams and fluid regulators to meet customer requirements. Chop-check and 2-ball pumps are used in extrusion applications.
Coating
This involves application of material by either spray or dipping. Coating applications use 2-ball and 4-ball pumps.
Measuring/Dispense
Measuring and dispense involves the delivery of a specified quantity of fluid on a repetitive basis. Measuring and dispense applications use 2-ball, 4-ball and chop-check pumps.
Ratio
Ratio is the effective area differential between the air motor piston and the lower end plunger rod. An 11:1 ratio indicates the pump air motor piston has 11 times the effective area of the fluid handling piston.
Higher ratio pumps produce higher fluid pressures which allows them to either move higher viscosity fluids or transfer fluids longer distances.
AAt 100 psi of inlet pressure, an 11:1 pump produces 1,100 psi of fluid outlet pressure.
BA 23:1 pump wouldproduce 2,300 psi of fluid outlet pressure, given the same air inlet .
Materials of ConstructionPump components are constructed of different materials to ensure the pump is best suited for a particular application.
Lower Pump End Component Options
Stainless Steel – Used with corrosive fluids and water-borne materials. Stainless steel is corrosion resistant. It can be heat-treated, hard chrome-plated or Ultra-Coated to improve abrasion resistance.
Carbon Steel – Provides excellent abrasion resistance. It can be heat-treated or hard chrome plated. Not suited for water-borne fluids and corrosive materials, as it will rust and deteriorate.
Packing Seal Options
Packing seals are used to seal movement of the plunger rod, both in the throat seal and piston seal areas of the pump. They are made of different materials to ensure chemical and material compatibility to maximize service life.
UHMW-PE (Ultra-High Molecular Weight Polyethylene) – An all-purpose packing material that provides excellent abrasion resistance. Commonly used with inks, acids, and some solvents.PTFE Compatible with all fluids. Provides excellent corrosion resistance but minimal abrasion resistance. Commonly used with corrosive chemicals, ketone, acids, and room-temperature vulcanizing (RTV) materials.PU Particularly suited to waterbased sealants and mastics offering excellent seal life and very high abrasion resistance. High resistance to mineral oils, suitable for lubrication pumps.
Staggered Combining packing seals made of different material combinations can often maximize service life by utilizing the strengths of both materials.
A11:1RATIO4.25"MOTOR
B23:1
RATIO6”
MOTOR
100 PSI(6.89 bar)AIR INLET
1,100 PSI(75.8 bar)
FLUIDOUTLET
2,300 PSI(158.5
bar)FLUID
OUTLET
Transfer & Supply
Materials• Caulking• Heavy Lubricants• Mastics• Sealants• Inks• Grease
Chop-Check Pumps
The heavy-hitters of the line, Grunfeld chop-check pumps are designed to move medium- to high- viscosity fluids ranging from 15,000 to more than 1,000,000 cPs, and at delivery rates up to 12.2 gpm (46.3 L/min).
Extrusion
Lubrication
98
2-ball pumps are among the most versatile in the Grunfeld line. They are capable of handling applications from simple transfer to the extrusion of low- to medium- viscosity materials up to 100,000 centipoise (cPs) with fluid delivery up to 18.1 gpm (68.6 L/min).
2 Ball Pumps
Materials• Oils• Coatings• Paint• Chemicals
Spray
Extrusion
Transfer & Supply
Transfer & Supply
Materials• Paint• Chemicals• Varnishes• Enamels• Lacquers
4 Ball Pumps
Grunfeld 4-ball piston pumps are designed to transfer high volumes of low- and medium-viscosity fluids up to 12,500 cPs with fluid delivery up to 32.8 gpm (124.0 L/ min), depending on the application. A common use involves circulating fluid from the original container, to the point of use, and then back.
Flow (LPM) Maximum Delivery Rate L/min Ratio Fluid Pressure psi (bar) Pump Model Number Material of Construction Lower End Type 500 cPs 5000 cPs 250,000 cPs
1.4 28:1 0 - 4200 (0 - 289.6) NM2328A-11-X11 Stainless Steel 2-Ball1.9 22:1 0 - 3300 (0 - 277.5) NM2322E-XX-P4X Carbon Steel Chop-Check1.9 22:1 0 - 3300 (0 - 277.5) NM2322F-XX-P4X Stainless Steel Chop-Check2.8 43:1 0 - 6459 (0 - 451.5) AF0443S21XXXX Carbon Steel Chop-Check2.8 43:1 0 - 6459 (0 - 451.5) AF0443T21XXXX Stainless Steel Chop-Check2.8 43:1 0 - 6459 (0 - 451.5) AF0443S71XXXX Carbon Steel Chop-Check4.5 18:1 0 - 2700 (0 - 186.2) NM2318B-13-C43 Stainless Steel 2-Ball4.9 30:1 900 - 4629 (62.1 - 319.2) AF0430G11XXXX Stainless Steel 2-Ball4.9 60:1 1800 - 6172 (124.1 - 425.5) AF0660G11XXXX Stainless Steel 2-Ball4.9 65:1 0 - 7475 (0 - 515.5) AF0665S11XXXX Carbon Steel Chop-Check5.7 3.6:1 Hyd 180 - 4320 (12.4 - 297.9) 650935-C43-C Carbon Steel Chop-Check6.1 3.3:1 Hyd 165 - 3394 (11.4 - 234) 650944-C43-B Stainless Steel 2-Ball6.8 23:1 0 - 3690 (0 - 254.4) AF0423S11XXXX Carbon Steel Chop-Check6.8 46:1 0 - 7485 (0 - 516.1) AF0646S11XXXX Carbon Steel Chop-Check7.2 22:1 660 - 3412 (45.5 - 235.3) AF0422G11XXXX Stainless Steel 2-Ball7.2 45:1 1350 - 5459 (93.1 - 376.4) AF0645G11XXXX Stainless Steel 2-Ball
10.2 2:1 Hyd 100 - 2400 (6.9 - 165.5) 650934-XXX-C Carbon Steel Chop-Check11 9:1 0 - 1350 (0 - 93.1) AF0409C51XXXX Stainless Steel 2-Ball
10.6 9:1 0 - 1350 (0 - 93.1) AF0409AX1XX24-02 Carbon Steel 2-Ball11 9:1 0 - 1350 (0 - 93.1) AF0409C11XXXX Stainless Steel 2-Ball
11.7 0.58:1 Hyd 85 - 2054 (5.9 - 141.6) 650943-XXX-B Stainless Steel 2-Ball11.7 1.7:1 Hyd 85 - 2040 (5.9 - 140.7) 650945-XXX-B Stainless Steel 2-Ball12.1 23:1 0 - 4125 (0 - 290.6) AF0623S11XXXX Carbon Steel Chop-Check12.1 12:1 0 - 2085 (0 - 143.8) AF0412S11XXXX Carbon Steel Chop-Check14 11:1 330 - 1747 (22.8 - 120.5) AF0411G11XXXX Stainless Steel 2-Ball14 23:1 690 - 3495 (47.6 - 241) AF0623G11XXXX Stainless Steel 2-Ball14 40:1 1200 - 4697 (82.7 - 323.9) AF0840G11XXXX Stainless Steel 2-Ball
14.4 44:1 1320 - 3964 (91 - 273.3) AF0844S11XXXX Carbon Steel Chop-Check
15.5 2:1 0 - 300 (0 - 20.7) 650110-C Carbon Steel 2-Ball15.1 9:1 270 - 1350 (18.6 - 93.1) CL0409A91LL2DE31 Carbon Steel 2-Ball15.1 9:1 270 - 1350 (18.6 - 93.1) CL0409A91LL2DE3B Carbon Steel 2-Ball15.9 4:1 0 - 600 (0 - 41.4) NM2304B-11-XXX Stainless Steel 2-Ball15.9 4:1 0 - 600 (0 - 41.4) NM2304B-41-XXX Stainless Steel 2-Ball15.9 4:1 0 - 600 (0 - 41.4) 650313-X, 650314-X Stainless Steel 2-Ball16.3 2:1 0 - 343 (0 - 23.6) 650311-X, 650312-X Stainless Steel 2-Ball16.3 2:1 0 - 351 (0 - 24.2) NM2202A-11-XXX Carbon Steel 2-Ball16.3 2:1 0 - 351 (0 - 24.2) NM2202A-41-XXX Carbon Steel 2-Ball16.3 2:1 0 - 351 (0 - 24.2) NM2202B-11-XXX Stainless Steel 2-Ball16.3 2:1 0 - 351 (0 - 24.2) NM2202B-41-XXX Stainless Steel 2-Ball16.7 4:1 0 - 600 (0 - 41.4) NM2304A-11-XXX Carbon Steel 2-Ball16.7 4:1 0 - 600 (0 - 41.4) NM2304A-41-XXX Carbon Steel 2-Ball20.4 45:1 1350 - 4050 (93.1 - 279.2) AF1045B11XXXX Carbon Steel 2-Ball20.4 65:1 1950 - 5850 (134.5 - 403.3) AF1265B11XXXX Carbon Steel 2-Ball22.7 28:1 840 - 3360 (57.9 - 231.7) AF0828S11XXXX Carbon Steel Chop-Check22.7 44:1 1320 - 3960 (91 - 273) AF1044S11XXXX Carbon Steel Chop-Check22.7 65:1 1950 - 5850 (134.5 - 403.3) AF1265S11XXXX Carbon Steel Chop-Check32.9 1.2:1 Hyd 60 - 2670 (4.1 - 184.1) 650941-XXX-C Carbon Steel Chop-Check
46.2 13:1 390 - 1900 (26.9 - 131) AF0813S11XXXX Carbon Steel Chop-Check46.2 20:1 600 - 2250 (41.4 - 155.1) AF1020S11XXXX Carbon Steel Chop-Check46.2 30:1 900 - 3250 (62.1 - 224.1) AF1230S11XXXX Carbon Steel Chop-Check48.8 0.8:1 Hyd 40 - 1600 (2.8 - 110.3) 650940-XXX-B Stainless Steel 2-Ball56.8 10:1 300 - 1200 (20.7 - 82.7) AF0810C11XXXX Stainless Steel 2-Ball56.8 10:1 300 - 1200 (20.7 - 82.7) AF0810F11XXXX Stainless Steel 2-Ball56.8 15:1 450 - 1350 (31 - 93.1) AF1015C11XXXX Stainless Steel 2-Ball56.8 15:1 450 - 1350 (31 - 93.1) AF1015FX, AF1015JX Stainless Steel 2-Ball64.4 0.3:1 Hyd 15 - 386 (1 - 26.6) 650949-XXX Stainless Steel 2-Ball68.1 1:1 0 - 150 (0 - 10.3) 612041-X Carbon Steel 2-Ball68.5 23:1 690 - 2070 (47.6 - 142.7) AF1223C11XXXX Stainless Steel 2-Ball68.5 23:1 690 - 2070 (47.6 - 142.7) AF1223F11XXXX Stainless Steel 2-Ball68.5 23:1 690 - 2070 (47.6 - 142.7) AF1223C51XXXX Stainless Steel 2-Ball
80.6 2:1 60 - 312 (4.1 - 21.5) AF0402M11XXXX Stainless Steel 4-Ball80.6 4:1 120 - 633 (8.3 - 43.6) AF0604M11XXXX Stainless Steel 4-Ball84.8 0.2:1 Hyd 10 - 278 (0.7 - 19.2) 650950-XXX Stainless Steel 4-Ball89 7:1 210 - 1009 (14.5 - 69.6) AF0807M11XXXX Stainless Steel 4-Ball
110.9 3:1 90 - 457 (6.2 - 31.5) AF0603M11XXXX Stainless Steel 4-Ball124.2 5:1 150 - 702 (10.3 - 48.4) AF0805M11XXXX Stainless Steel 4-Ball
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
1,000,000 cPs
Ram Mounted
100,000 cPs
Ram Mounted
500,000 cPs 750,000 cPs
Ram Mounted
Ram Mounted
Ram Mounted
75,000 cPs
Ram Mounted
35,000 cPs 50,000 cPs
Flooded Inlet
Flooded Inlet
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Flooded Inlet
Flooded Inlet
Flooded Inlet
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Ram Mounted
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Ram Mounted
Cart Mounted Extrusion
Cart Mounted Extrusion
Ram MountedSiphon
Siphon
Flooded Inlet Ram Mounted
7500 cPs
Flooded Inlet
Ram Mounted
Ram MountedFlooded Inlet
10,000 cPs
Flooded Inlet
Flooded Inlet
Flooded Inlet
Ram Mounted
Ram Mounted
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
12,500 cPs
Flooded Inlet
15,000 cPs
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Siphon
Flooded Inlet
Flooded Inlet
Flooded Inlet
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Flooded Inlet
Flooded Inlet
Siphon
Siphon
Siphon
Siphon
Siphon
20,000 cPs
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Flooded Inlet
0 - 7.2
0 - 14.4
0 - 32.9
0 - 68.5
0 - 124.2
1000 cPsSiphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Siphon
Flooded Inlet
Flooded Inlet
Flooded Inlet
Flooded Inlet
Siphon
Siphon
Pump-To-Fluid Viscosity Guide
Considerations: The Chart should only be used as a guide, and not as a complete solution to pump application. It does not take into consideration pressure losses due tosizes and lengths of hoses, piping runs, dispensing valves, hose swivels, and other restricting factors.
1110
Drum Capacity 200 Litres
Pump Ratio 65:1
Air Motor 305mm øPump Output
23 LPM (Litres per minute)
Outlet Port 1 1/4"
Base Dimensions
910mm -wide1260mm
Height1535mm (Closed)2035mm (Open)2535mm (With Hose)
Weight 200kgs
Technical Specification
“High viscosity adhesives and sealants
of 1,000,000 cps pumped at flow rates
of up to 23LPM”
BSA0202-HFor high speed manual, semi-automatic and fully automatic bulk dispensing of adhesives and sealants. The BSA0202-H Drum Pump System from Grunfeld will deliver adhesives and sealant to production lines with efficiency and reliability pumping from UN1A2 – 200L Steel Loose Head Drums
• Range of pump options, selected for chemical composition compatibility, material rheology, required flow rates and dispense distances.
• Range of follower plate options including stainless steel, Teflon coated, heated for warm dispense, different seal configurations, etc.
• Options include stainless steel wettable parts and PTFE Seals for more aggressive chemical constituents such as Methlymethacrylates.
• Teflon lined hoses can be specified for use with moisture curing adhesives and sealants. See our website section on Delivery Hoses
• Drum Loading Roller tracks are available as an option to facilitate safe drum handling.
• Range of extrusion guns available, both manually operated and fully automated dispense heads for robotic mounting.
• Low maintenance for reliable production line integration.
1312
BSA0203-MSpecifically designed for pumping
methacrylate adhesives. All wettable parts are constructed from 17-4 stainless steel with
ceramic coating for maximum chemical and abrasion resistance.
A 2-Ball pump with excellent performace when pumping both Part A and Part B.
With Grunfeld’s unique control panel and graphical interface for ease of use.
Platen bleed valve for mess free drum changes. Options for drum centering and
clamping.
“Specially designed to have maximum
chemical and abrasion resistance”
Drum Capacity 200 Litres
Pump Ratio 23:1
Air Motor 152mm øPump Output
14.3 LPM (Litres per minute)
Outlet Port 1"
Base Dimensions
910mm -wide1260mm
Height1535mm (Closed)2035mm (Open)2535mm (With Hose)
Weight 150kgs
Technical Specification
adhesivechemistry
1514
LPMmethacrylate
pump
flow rates
fluid viscosity
High Pressure HosesUltra high pressure PTFE/ FEP Composite Material Hoses.
PTFE/ FEP core provides maximum protection against moisture ingress and provides high chemical resistance.
Superior material hose wuth pressure ratings of up to 520 bar.
Multiple braided reinforcements of aramid and steel to give the highest possible pressure rating.
With a polyurethane outer sheath to provide durabilty and to reduce the possibility of damage to painted parts while going through production processes.
Extrusion GunsRange of high performance, ruggedised extrusion guns for use in many hand applications.
Large range of stainless steel dispense tips available and threaded adaptors to enable use of disposable plastic nozzles and accessories.
Spray GunsAgain, using the same range of ruggedised gun bodies, our range of airless spray application guns can be used to spray coatings of up to 200,000 cPs.
A large range of tungsten carbide tips are available, offering flow rates of up to x LPM and fan widths of up to 300mm. All spray guns come with tip protectors.
Inner Ø Bend Radius
Working Pressure
Burst Pressure Weight
1/4” 50mm 700 bar 2800 bar 27 kg/100m
3/8” 80mm 520 bar 2080 bar 30 kg/100m
1/2” 100mm 450 bar 1800 bar 40 kg/100m
3/4” 150mm 345 bar 1379 bar 69 kg/100m
1” 200mm 345 bar 1379 bar 89 kg/100m
Technical Specification
“Five layers to ensure superior performance. FEP / Aramid / Polyurethane / Steel Braid / Polyurethane”
“High performance ruggedised extrusion
and spray applicators”
This is just a selection, we have a large range of guns available. Contact us with your requirements.
1716
AFR’sAFR’s (Air Flow Regulators) control pump flow minimising pulsation as the pump reciprocates.
For operators applying adhesives and sealants, a continuous flow of product is essential for effective application. The correct AFR will ensure a pulsation free output.
Again chemical and material compatibility must be specified for correct operation.
Material FiltersMaterial Filters prevent foreign bodies from entering dispense guns and valves, essential for ensuring correct operation. With a choice of filter housing materials and different screen sizes, your end of line equipment will be protected.
Available in carbon steel, nickel plated, or stainless steel to ensure chemical compatibility.
Stainless steel filter screens from 75μ to 375μ available.
“AFRs are essential in ensuring that output is
pulse free”
“Avoid expensive downtime by protecting your end of line dispense equipment
from foreign bodies”
Model No. Housing Base Seat MaterialRegulated Pressure
Range
Mox. Inlet
Pressure3/8” Ports, flow 11.4 L/min651780-A1A-B Carbon Steel Tungsten Carbide 28 - 86 bar 207 bar651780-A1B-B Carbon Steel Tungsten Carbide 69 - 207 bar 414 bar651780-A3A-B Stainless Steel Tungsten Carbide 28 - 86 bar 207 bar651780-A3B-B Stainless Steel Tungsten Carbide 69 - 207 bar 414 bar3/8” Ports, flow 22.7 L/min651780-B1A-B Carbon Steel Tungsten Carbide 28 - 86 bar 207 bar651780-B1B-B Carbon Steel Tungsten Carbide 69 - 207 bar 414 bar651780-B3A-B Stainless Steel Tungsten Carbide 28 - 86 bar 207 bar651780-B3B-B Stainless Steel Tungsten Carbide 69 - 207 bar 414 bar3/4” Ports, flow 75.7 L/min651780-C1B-B Carbon Steel Tungsten Carbide 52 - 172 bar 414 bar651780-C1C-B Carbon Steel Tungsten Carbide 138 - 354 bar 414 bar651780-C3B-B Stainless Steel Tungsten Carbide 52 - 172 bar 414 bar3/8” Ports, Remote Models 22.7 L/min651780-B1R-B Carbon Steel Tungsten Carbide 28 - 345 bar 414 bar651780-B3R-B Stainless Steel Tungsten Carbide 28 - 345 bar 414 bar3/4” Ports, Remote Models 22.7 L/min651780-C1R-B Carbon Steel Tungsten Carbide 52 - 345 bar 414 bar651780-CR3-B Stainless Steel Tungsten Carbide 52 - 345 bar 414 bar
1918
2120
Grunfeld Fluid Dynamics Ltd:
+44 1626 [email protected]
grunfeld-fluid.com
“We’re always ready to hear about your adhesive dispense requirements. Get in
touch...”