Te
st &
Mea
sure
men
t
Prod
uct B
roch
ure
| 02.
00R&S®TS-PSM1Power Switching ModuleHigh-power multiplexer and multiple DUT power switching module
TS-PSM1_bro_en_0758-0616-12.indd 1 07.11.2013 11:53:08
Fron
t con
nect
or X
10
Analog busX30
Exte
nsio
n co
nnec
tor X
20
GNDlines
Couplingrelays
ABA1
ABB2
ABA2
ABC1
ABD2
ABD1
Analog bus (AB)
LABA
1
LABB
2
LABA
2
LABC
1
LABD
2
LABD
1
GND
IL1, IL2
GND
IL1noIL1com
ABB1
LABB
1
ABC2
LABC
2
Local analog bus (LAB)
CH9noCH9com
CH11noCH11com
CH13noCH13com
CH15noCH15com
IL2noIL2com
CH10noCH10com
CH12noCH12com
CH14noCH14com
CH16noCH16com
LABA
1LA
BC1
LABB
2LA
BD2
LABA
2LA
BC2
CH1no
CH2no
CH3no
CH4no
0R01
0R01
0R01
0R01CH5no
CH6no
CH7no
CH8no
0R01
0R01
0R01
0R01
IL2com
CH10com
CH12com
CH14com
CH16com
IL1com
CH9com
CH11com
CH13com
CH15com
LPBB
CH2com
CH4com
LPBA
CH1com
CH3com
CH6com
CH8com
LPBC
CH5com
CH7com
LPBD
B D
A B C DIL1
IL2
X1
CHA-GND
TERMINAL
2
R&S®TS-PSM1Power Switching ModuleAt a glanceThe R&S®TS-PSM1 is a power switching module controlled by a CAN-bus interface. Its innovative technology and versatile functionality make it ideal for automotive and high-current switching applications, e.g. power-management and test-load paradigms.
The special design of the module ensures ideal routing of supply and load paths through the test system. High-current force channels and sense channels from voltage or current sources can be switched and routed to the DUTs via the module. In the opposite direction, single-pole or multipole loads can be applied to the DUTs. High-power multiplexers on the module make it possible to select different load simulations for integration in the R&S®TSVP test system versatile platform base units.
The currents and voltages can be measured or monitored at all switching nodes by means of additional relays on the module and the Rohde & Schwarz analog bus. Shunt resis-tors are inte grated for measuring high currents.
This characteristic is particularly important if the power consumption of the DUT must be measured during nor-mal operation and in standby modes. Additionally, the tests of various operating modes and their current con-sumption can be executed without interrupting the DUT’s powerpath.
The R&S®TS PSM1 power switching module can be used in the R&S®CompactTSVP and in the R&S®PowerTSVP. It is a CAN-bus- controlled module which takes up only one slot.
Functional block diagram of the R&S®TS-PSM1
TS-PSM1_bro_en_0758-0616-12.indd 2 07.11.2013 11:53:08
Rohde & Schwarz R&S®TS-PSM1 Power Switching Module 3
Key facts ❙ Power switching module for supplies and loads ❙ Switching module for voltages of up to 70 V ❙ 8 high-power channels with 16 A max. ❙ 10 power channels with 2 A max. ❙ 4 high-power 4-to-1 multiplexer channels with 16 A max. ❙ Indirect high-current measurements on high-power channels via shunt resistors
❙ Direct current measurements up to 1 A in all channels via R&S®TSVP analog measurement bus and R&S®TS-PSAM
❙ Selftest of all relays via R&S®TSVP analog measurement bus and R&S®TS-PSAM
❙ Analog measurement bus access to 8 bus lines ❙ Control interface based on CAN bus ❙ Usable in R&S®CompactTSVP and R&S®PowerTSVP ❙ LabWindows/CVI device driver support ❙ GTSL test software library in DLL format
Flexible signal routingThe design of the switching module and the large voltage and current ranges ensure high flexibility and a wide ap-plication range.
Device-internal connection of the multiplexed power chan-nels even makes it possible to configure complex yet flex-ible load systems with original or electronic loads to obtain a high- current R&S®PowerTSVP switching instrument.
When lower power signals are measured, the signal con-cept relies on the system-wide analog bus.
Soft front panel for the R&S®TS-PSM1.
Proper handling of analog signals led to the R&S®TSVP analog bus interconnection solution. The analog bus is lo-cated immediately above the front connector area, where space is provided for on-board signal conditioning and sig-nal routing. The distance to the digital signals on the back-plane significantly improves signal quality.
In addition, dedicated switching modules such as the R&S®TS-PSM1 are controlled via the low-noise and inter-ference-resistant CAN bus, which ensures overall high reli-ability and signal quality, especially in the vicinity of high-current signals.
Direct current measurement via the analog measurement bus is limited to 1 A, but measurements up to 16 A can be performed by forwarding the shunt resistor voltages of the R&S®TS-PSM1 via the analog bus to a precise multimeter such as the R&S®TS-PSAM in the R&S® CompactTSVP.
Typical applications ❙ Switching of voltage or current sources to DUTs ❙ Switching of DUT loads as original loads or simulated/electronic loads
❙ Power multiplexer for DUT signals to test devices ❙ Analog functional test for general-purpose signals ❙ Switch simulation for DUTs
Software supportA LabWindows/CVI driver according to the IVI standard is available for the module’s switching functions. Function panels and online help are available as common features for the LabWindows/CVI driver.
Security by selftest and diagnostic featuresThe module’s built-in selftest capability ranges from fast diagnostics to the complete, automated evaluation of all relays and switching paths (R&S®TS-PSAM required). Di-agnostic LEDs on the module front panel speed up system integration and allow proper operation to be determined at a glance.
TS-PSM1_bro_en_0758-0616-12.indd 3 07.11.2013 11:53:08
Rohde & Schwarz R&S®TS-PSM1 Power Switching Module 4
SpecificationsSpecificationsApplication in the R&S®TSVP platform R&S®CompactTSVP or R&S®PowerTSVP 1 slot required
Interface
Control bus CAN 2.0b (1 Mbit/s)
DUT connector (front) DIN 41612, 96 pins
I/O connector (rear) CompactPCI connector J2, 110 pins
Control logic
Local microprocessor ST10, 16 bit, 40 MHz
Switching characteristics
High-power switching channels
number/type of relays 8/Zettler AZ764
contact configuration 8 × SPST
switching voltage DC/AC (max.) 70 V DC, 46 V peak, 33 V (RMS)
switching current (max.) 16 A/16 A RMS (continuously)
switching power (max.) 480 W/4000 VA (resistive load)
current measurement
indirect via shunt 5 mΩ shunt resistor ±0.6 % ±60 ppm/K (for 20 °C to 60 °C)
direct via analog bus with R&S®TS-PSAM, 1 A/10 W (max.)
High-power multiplexer
number/type of relays 16/Zettler AZ764
contact configuration 4 multiplexers, 4-to-1
switching voltage DC/AC (max.) 70 V DC, 46 V peak, 33 V (RMS)
switching current (max.) 16 A/16 A RMS (continuous)
switching power (max.) 480 W/4000 VA (resistive load)
Medium-power switching channels
number/type of relays 10/Zettler AZ832
contact configuration 10 × SPST
switching voltage DC/AC (max.) 70 V DC, 46 V peak, 33 V (RMS)
switching current (max.) 2 A/2 A RMS (continuously)
switching power (max.) 150 W/250 VA (resistive load)
current measurement
direct via analog bus with R&S®TS-PSAM, 1 A/10 W (max.)
Monitor switching channels
number/type of relays 6/Meder RM-05
contact configuration 12 multiplexers 4-to-1
switching voltage DC/AC (max.) 70 V DC, 46 V peak, 33 V (RMS)
switching current (max.) 1 A/1 A RMS (1.5 A carry)
switching power (max.) 10 W
current measurement
direct via analog bus with R&S®TS-PSAM, 1 A/10 W (max.)
Analog measurement bus access 8 lines
TS-PSM1_bro_en_0758-0616-12.indd 4 07.11.2013 11:53:08
Rohde & Schwarz R&S®TS-PSM1 Power Switching Module 5
Ordering informationDesignation Type Order No.Power Switching Module R&S®TS-PSM1 1143.0139.02
R&S®CompactTSVP Test and Measurement Chassis R&S®TS-PCA3 1152.2518.02
R&S®PowerTSVP Industrial Switching Application Chassis R&S®TS-PWA3 1157.8043.02
General dataPower consumption +5 V/4.0 A (max.; all relays switched)
Environmental conditions
Temperature operating temperature range +5 °C to +40 °C
storage temperature range –10 °C to +60 °C
Damp heat +40 °C, 80 % rel. humidity, steady state, in line with EN 60068-2-30
Mechanical resistance
Vibration sinusoidal 5 Hz to 55 Hz, 0.15 mm amplitude const.,55 Hz to 150 Hz, 0.5 g const., in line with EN 60068-2-6
random 10 Hz to 300 Hz, acceleration 1.2 g (RMS), in line with EN 60068-2-64
Shock 40 g shock spectrum, in line with MIL-STD-810E, method 516.4, procedure I
Product conformity
Electromagnetic compatibility EU: in line with EMC Directive 2004/108/EC applied harmonized standards: EN 61326-1 (industrial environment), EN 61326-2-1,EN 55011 (class A),EN 61000-3-2, EN 61000-3-3
Electrical safety EU: in line with Low Voltage Directive 2006/95/EC
applied harmonized standard: EN 61010-1
Dimensions W × H × D 20 mm × 174 mm × 316 mm(0.79 in × 6,85 in × 12,44 in)
Weight 0.75 kg (1.65 lb)
Calibration not required
TS-PSM1_bro_en_0758-0616-12.indd 5 07.11.2013 11:53:09
About Rohde & SchwarzRohde & Schwarz is an independent group of companies specializing in electronics. It is a leading supplier of solu-tions in the fields of test and measurement, broadcasting, radiomonitoring and radiolocation, as well as secure communications. Established more than 75 years ago, Rohde & Schwarz has a global presence and a dedicated service network in over 70 countries. Company headquar-ters are in Munich, Germany.
Certified Quality System
ISO 9001
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG
Trade names are trademarks of the owners
PD 0758.0616.12 | Version 02.00 | November 2013 (wb)
R&S®TS-PSM1
Data without tolerance limits is not binding | Subject to change
© 2004 - 2013 Rohde & Schwarz GmbH & Co. KG | 81671 München, Germany
Regional contact ❙ Europe, Africa, Middle East | +49 89 4129 12345 [email protected]
❙ North America | 1 888 TEST RSA (1 888 837 87 72) [email protected]
❙ Latin America | +1 410 910 79 88 [email protected]
❙ Asia/Pacific | +65 65 13 04 88 [email protected]
❙ China | +86 800 810 8228/+86 400 650 5896 [email protected]
Rohde & Schwarz GmbH & Co. KGwww.rohde-schwarz.com
Environmental commitment ❙ Energy-efficient products ❙ Continuous improvement in environmental sustainability ❙ ISO 14001-certified environmental management system
Service that adds value❙ Worldwide ❙ Local and personalized❙ Customized and flexible❙ Uncompromising quality ❙ Long-term dependability
0758
.061
6.12
02.
00 P
DP
1 e
n
0758061612
TS-PSM1_bro_en_0758-0616-12.indd 6 07.11.2013 11:53:09