TN9 system for pharmacies and drugstores - Introduction
Caem presents a series of innovations that complement the current offer based on the structure TN9 and everything that revolves around it, to complete and improve the proposal of furniture in pharmacies and drugstores, as well as new display solutions, aesthetic and point of sale communication .
TN9 system for pharmacies and drugstores
WALL: TN9 available from H192 to H296, optimizes the backs based on the height of the base that is chosen, trying to avoid where possible the use of the backs H8. Normally the depth of the base are 30 and 40, it depends on the applications and from the surface of the pharmacy in question.
The steps required are 45-70-80-100, but remain available steps Caem standard as the 133, where the surfaces are large and may be required. In this case care must be taken to the reinforcement (1) to predict more than 100, it is in the plans in metal and in glass tops.
It 'also required the reinforcement under the metal shelves 30cm deep.
It is mandatory to provide a wall mount for each pillar and wall structures in central room, always check the layout and possible problems of stability and security.
Montante TN9 and Base TN – Inserts and Adj Feet
Both the uprights which provide the basessupport galvanized and a legadjustable.The uprights can beExtended with the appropriate supportGalvanized 101C # Z
Linear Module TN9: Dimensions
Wall Unit: side views
Warning:In Configuration Plan Base Podium lateral dimensions will not be 9 + 30cm + 2cm, but 9 + 34cm.
TN9 system for pharmacies and drugstores - Wall Linear Structures
EXAMPLE OF WALL WITH PLANS IN GLASS AND CABINET
The graphics adhesive or magnetic
this case directly attached above the top back.
Glass top 25cm, on shelf minimal 10, step 80. 1 drawer cabinet in melamine Socket frame with plexi opal,
backlit. The T5 tubes is secured under the cabinet. The configuration is for guidance only.
90° Corners Internal and External
AAA = 90° External
AAT = 90° Cut Internal
Available in configurationto entire floors T13, modular Multi-storey, glass shelves suspended.Not available basic plans Podium.
Special Corners– AAI 45°
The configuration represents a possible configuration with AAI to 45 ° internal corners which connect the linear elements creating curved walls.
Special Corners– AAE 45°
The configuration represents a possible configuration of AAE to 45 ° internal corners which connect the linear elements creating
Angoli AAI – AAE – 45°
Available in configurationto entire floors T13, modular Multi-storey, glass shelves suspended.Not available basic plans Podium.
Gondola, plan view
Gondola – Side View
Gondola End – Promo Ends
TN9 Gondola with Ends Side A - TN9 End No Base Side B - TN9 End With Base H = 112 to 236
Upright Side Cover is 3cm to align
Mast coverage is wider than normal to guarantee alignment of designL = 3cm ; H = HHH -9PIT51203A # HHH03(HHH H = upright).Does not include capson the uprights
TN9 End – No BaseStraight Lines when using a Podium
TN9 End – With BaseStraight Lines when using a
Podium
Podium
No Podium
Podium
SLIM40 Gondola End
No Base SLIM40H = 112-128-136-148-156-172
End SLIM40 - Details
step 70cm Footprint L78cm x 4 x H H = 112-128-136-148-156-
172 * (+ feet TN9, 25mm≈50mm)
Top cover with or without support door-sign
Mono-pitch 40mm slots for all displays Tn, step 70, only front
Standard front step back 70 - H8-24-44
* For the height H172 upper additional reinforcements are necessary in the design phase
Composition 1 KIT tested:Panel nr1-9PIT50701A # HHHPPPBacks - quantity and type to be
verified on the basis of 'HHH, use backrests standard 44-24-8, passo70cm for composition
Cover without holes No.1 9PIT50702A # PPP
or alternativelyCover with holes * No.1
9PIT50702B # PPPNo. 2 feet 101A C #NR.8 Autofil.6.3 * 16991 #
03A316* Add No.2 supports 990 # 0024 and screws only for the covers with holes
Slim40 – Plan View
The head Slim40 because only 40mm lateral dimensions, in addition of course side of the upright pack size of 15mm on each side. The back to step 70cm is inserted in the rear panel, the footprint of the panel is 78cm to optimize the layout when mounting plans Podium base.When mounting the floors T13 of the base, the head SLIM40 does not make the thread, but protrudes from the front of the plane and the tip of the base, as shown in figure
Esploso composizione tipo.Esempio.
Gondola Options
Base Shelf with Multi Planks.
Ground Base Full non pierced 'Extra' and socket Metal.
Ground Base Podium is a base shelf with front kicker in a single piece.Not drilled and Socket Integrated Metal. Finishes Side Stands L = 3 and Bases.Ground Base Podium non pierced with Socket Integrated metal.Suspended floors glass.Finishes side stanchions and bases.
Drawer independent escort, according to H16 and 24.Basic plan T13 # N.
Gondola Options
Ground Base Podium.Suspended floors in metal.TG configuration SLIM40 with metal shelves
TG semi-circular configuration, floor base metal, suspended floors
glass
Custom configuration
and related
On Castors
The Kit nr. 3 connecting bars under the basic plans provides Nr. 6 wheels, available in Ø60mm and Ø50mm (with and without brake)
TG semi-circular configuration, which is also available with wheels *.Provide a wheel on the same model as those used in gondola
Provide a stabilizer bar in every sector to be mounted between the uprights.
On Castors A fully modular castors system is Available to make gondolas Mobile and safe
Improved Product Merchandising
The shelf is not drilled on Pharma25, dedicated to the pharmacy.
The floor 30cm and 40cm by 25cm deep, and in the steps 70-80-100 and a height of only 25mm, optimizes the merchandising of the store thanks to the new door-price label H26mm, rocker, available in transparent finish.
PHARMA25 Bracket is slimmer, with reduced height and less metal visible
Available L25-L30-L40P045-P070-P080-P100-P133
30cm shelf has an undershelf weld support
New: EPOS H26mm
New Epos H26mm. T46#B – for T13 metal one piece shelves compatible with TN9
NEW EPOSH26mm. 146#P – for glass shelves 8mm
Transparent in P070-P080-P100-P-133
Available transparentP070-P080-P100-P-133The door-front prices cluttering 32mm and both are swinging. It can be mounted on thickness from 6mm to 10mm.
Shelf Management
Organization system of the shelf in transparent acrylic. A rail adhesive back allows to frame dividers H35mm.Rail L = P - 4mm for the metal shelvesRail L = P - 47mm for glass tops
H&H System
Rail - Profile rear adhesiveL = P - 4mm for the metal shelvesL = P - 47mm for glass tops
Dividers: Prof.netta = Depth rated floor - 10mm
Detail at the back
Made to order
New Bracket PHARMA25-9PIT50801A#
Shelf 2 hooks, depth 25 and 30, # 2225 and # 22303 shelf hooks, depth 40, 3240 #Tilt -15 ° / 0 °To plan T13The front door is the thread of the money for labels from 26mmThe new shelf-profile thinner by the aesthetics
and function, optimizing the merchandising and handling products with the entire plans '' Extra ''.
Minimal Glass Shelf
Depth 20-25-30-40Steps 65-70-80-100-133 ** predict reinforcement mandatory
ThoughenedRounded Front CornersSafe Smooth Edges
For matt and colored finishes, please enquire specifically
New Base Shelf PODIUM – 9PIT5120A#N00HHLLPPP
WHERE:N = non-pierced00 or 01 = number reinforcementsHH = Height base 16 or 24LL = Depth base (30-40)PPP = Step (100-080-070)
More than 100 expected reinforcement 1Not available for cornersSPECIAL ':
A plan that goes on a 30cm, 34cm really cluttered, serve then covers basic special for TG and in the mural, also serve covers uprights special only in TG (in order to go to cover the part of the plan surplus TG step 70cm)Basic coverage:9PIT51202A # HHHLL R (right HHH = 016 or 024, LL = 30)9PIT51202A # HHHLL L (left HHH = 016 or 024, LL = 30)Mast coverage L3 *:9PIT51203A # HHH03 (HHH H = upright)* A bayonet mount before, they do not need caps upright, cluttered 3cm.
Bulk Display
Bulk display details
Code Description Qty Back Bulk P = XXX 9PFR22502A PPP # 1 Piano Bulk P = XXX 9PFR22503A # 1 PPP Shelf dx 2 positions 25 ° - 30 ° 9PFR22501A # 1 R Shelf sx 2 positions 25 ° - 30 ° 9PFR22501A # 1 L Rivets 4 * 8993 # 0010408A 4 Front glass H 14 P = XXX 9SA FR225XXX # 1 Side glass dividers H 14 L 25 * 9SA FR22504A # 1 * Provide the minimum number of partitions of 2 pieces per
exhibitor, in addition to the dividers customer choice
Bulk Details
dimensional dataPLANNED STEPS: 45-70-80-100DEPTH 'PROFIT: 26.5 cmHEIGHT OF GLASSES: 14 cmOVERALL MAX 20 °: 34.2 cm
(from the back) + price holderOVERALL MAX 30 °: 31.7 cm
(from the back) + price holderHOLDERS: Both h39mm that T46
T46 # A # B h 26mmGLASS: Polished wire, hardened,
6 mm thickSTEP RACK PARTITIONS GLASS:
64mm
Covers
Covers uprights bayonet mod. C 110 # C09 and covers basic left and right # 109A contribute to the overall improvement of the aesthetic.
Podium for the plan to provide for the specific hedging 9PIT51202A #
Sliding Upright Side Covers
Covers uprights bayonet mod. C 110 # C09 must be compulsorily installed before placing the uprights vertically. Place the mast on the ground horizontal or tilt it to be able to enter the coverage in the fins. Also it applies to covers L3.
Top Covers and Signage Holders
9PIT48490A # PPP PPP = 65-70-80-100-133 PPP <= 070, two supports PPP> = 100, three supports Support door-sign 990 # 0024 + 991 # 01D04016 TS Screw 4 * 16
pcs. 1 each 991 # 06004000 Washer D = 4
pcs. 1 each 991 # 02A04000 nut TE D = 4
pcs. 1 each
Top Covers with Signage Holder
Top Cover with Pre Drilled Holes
Wall Unit Signage Holder
170H # 044RC and LC (H44)
170H # 052RC and LC (H52)
120 # 008PPPC - Nr.2 168 # APPPC - No.1 168 # BPPPC - No.1 991 # 05C04009 - Nr.4 PPP = 070-080-100-133
The mounting bracket can be tilted and positioned to sign up that you want, based on the height that you want to cover with the posters. Available in two heights 44cm and 52cm, it becomes useful when the store there are different ceiling heights, you can order the same height of the uprights by adjusting only the signs on the basis of false ceilings.
Wall Signage
Caem does not provide the posters, we recommend thicknesses of 3 / 4mm
More options for Stock and Back Door Rooms
Metal drawer H40 L50 P100 - Available with and without lock
Metal drawer H28 L50 P100 - stackableAvailable without lock
Pharmacy VS OTC OTC is ‘over the counter’, the self service area of a pharmacy OTC represent a higher sales area for the pharmacy
business, letting customers browse and buy product, both by need and by impulse
Pharmacy is the professional area ‘behind the counter’ Pharmacy is mixed with Dispensary, where medicines are
stocked and the pharmacist operatesAn example follows of different pharmacy set ups to have more
or less OTC space by using shelving or drawers in the dispensary. The green units represent extra display area in OTC obtained by the use of more efficient dispensary area
Basic
MediStock
MediBasic
MediSales
RX Sales
Which solution to use?
Dispensary with MAG Shelving
Dispensary with Medidrawer The same drawer, more sizes, more options.
Never fixed for current and future use
Dispensary with Medidrawer Adjustable, two inclinations pull out shelf
Dispensary with Medidrawer
Dispensary with Medidrawer
Dispensary, LabWork tables and closed drawers, In the same modular adjustable structure. Integrated with Medidrawers open pullout shelves.
Dispensary, LAB
CAEM UKUnit 3, Jamage Ind Est
Talke - ST7 1XWUK
01782 794500
PharmaCaem - https://drive.google.com/open?id=0BznLrkRuPitHX29Ed1VXb1hRSGs
Medidrawerhttps://drive.google.com/open?id=0BznLrkRuPitHTkRkbXl3aUliRUk
RX Drawerhttps://drive.google.com/open?id=0BznLrkRuPitHaGFEU3F5N0kxV1k
Hospital https://drive.google.com/open?id=0BznLrkRuPitHaGFEU3F5N0kxV1k
Pharmacy VS OTC https://drive.google.com/open?id=0BznLrkRuPitHR0ZMWHJuUFVVWkk
Perfumeriehttps://drive.google.com/open?id=0BznLrkRuPitHSDBYQVFWS3F2NnM
Pharmacyhttps://drive.google.com/open?id=0BznLrkRuPitHSnVyV29WdTRxS0E
RX brochurehttps://drive.google.com/open?id=0BznLrkRuPitHNDNZMFdyamlXcXc