MODEL 2639 AWWA C509 FULL BODY DUCTILE IRONMODEL 2640 AWWA C509 FULL BODY GRAY IRON
516509_B 11/16/10 2:40 AM Page 1
MODEL 2639 & 2640
2639 2640
304 Stainless Steel
304 Stainless Steel
304 Stainless Steel
304 Stainless Steel
304 Stainless Steel
Copper Alloy
Copper Alloy
Copper Alloy
Copper Alloy304 Stainless Steel
Copper Alloy
Copper Alloy
Copper Alloy
Copper Alloy
Copper Alloy
Copper Alloy
516509_B 11/16/10 2:40 AM Page 2
MODEL 2639 & 2640
26392640
304 Stainless Steel
304 Stainless Steel
304 Stainless Steel
304 Stainless Steel
Copper Alloy
Copper Alloy
Copper Alloy
Copper Alloy
Copper AlloyCopper Alloy
Copper Alloy
Copper Alloy
Copper Alloy
Copper Alloy
Copper AlloyCopper Alloy
516509_B 11/16/10 2:40 AM Page 3
MODEL 2639 & 2640
F-6136
516509_B 11/16/10 2:40 AM Page 4
MODEL 2639 & 26402640
2639
516509_B 11/16/10 2:40 AM Page 5
2"-12" R/W VALVEN.R.S. ASSEMBLY MATERIAL LIST
516509_B 11/16/10 2:40 AM Page 6
MODEL 2639 & 2640
516509_B 11/16/10 2:40 AM Page 7
MODEL 2639 & 2640
F-6100
516509_B 11/16/10 2:40 AM Page 8
MODEL 2639 & 2640F-6106
516509_B 11/16/10 2:40 AM Page 9
MODEL 2639 & 2640F-6114
516509_B 11/16/10 2:40 AM Page 10
MODEL 2639 & 2640
F-6112
516509_B 11/16/10 2:40 AM Page 11
MODEL 2639 & 2640
F-6113
516509_B 11/16/10 2:40 AM Page 12
MODEL 2639 & 2640
F-6110
516509_B 11/16/10 2:40 AM Page 13
MODEL 2639 & 2640
F-6111
4"-12" R/W MECHANICAL CUTTING-IN JOINT(MCJ) ENDS
GENERAL DIMENSIONS
516509_B 11/16/10 2:40 AM Page 14
MODEL 2639 & 2640
D
A
B
F
E
516509_B 11/16/10 2:40 AM Page 15
MODEL 2639 & 2640
F-6103
516509_B 11/16/10 2:40 AM Page 16
MODEL 2639
516509_B 11/16/10 2:40 AM Page 17
MODEL 2639
516509_B 11/16/10 2:40 AM Page 18
MODEL 2639 & 2640
516509_B 11/16/10 2:40 AM Page 21
MODEL 2639 & 2640
516509_B 11/16/10 2:40 AM Page 23
516509_B 11/16/10 2:40 AM Page 24
516509_B 11/16/10 2:40 AM Page 25
MODEL 2639 & 2640
516509_B 11/16/10 2:40 AM Page 26
MODEL 2639 & 2640
Valves shall conform to the latest revision of AWWA Standard C-509 covering resilient wedgegate valves.
The valves shall be either, non-rising stem or rising stem, opening by turning stem left orright and provided with 2” square operating nut or handwheel with the word Open and anArrow cast in the metal to indicate direction to open.
The wedge shall be of cast iron completely encapsulated with rubber.
The sealing rubber shall be permanently bonded to the cast iron wedge to meet ASTM testsfor rubber metal bond ASTM D429
Stems for NRS assemblies shall be cast copper alloy with integral collars in full compliance withAWWA. OS & Y stems shall be copper alloy. The NRS stem stuffing box shall be the o-ringseal type with two o-rings located above thrust collar and one o-ring below. The two o-ringsabove the thrust collar shall be replaceable with valve fully open and subjected to full ratedworking pressure.
There shall be two low torque thrust bearings located above and below the stem collar. Thestem nut shall be independent of wedge and shall be made of solid copper alloy. There shallbe a smooth unobstructed waterway free of all pockets, cavities and depressions in the seatarea.
The body and bonnet shall be coated with fusion bonded epoxy both interior and exterior, com-plying with AWWA C550 and be NSF 61 certified. Each valve shall have maker’s name,pressure rating and year in which manufactured cast on the body. Prior to shipment from fac-tory, each valve shall be tested by hydrostatic pressure equal to requirement for both AWWA(twice the specified working pressure) and 400 PSI ULFM requirements.
516509_B 11/16/10 2:40 AM Page 27