8/17/2019 Manual Transmàssion 6 speed.pdf
1/55
8/17/2019 Manual Transmàssion 6 speed.pdf
2/55
8/17/2019 Manual Transmàssion 6 speed.pdf
3/55
CLUTCH - HOW TO FOLLOW THIS MANUAL21-2
How to Follow this Manual
How to Follow this ManualExtent of maintenance operation covered in this manualThis manual explains the maintenance procedure after the transmission has been removed from thevehicle. Please consult the relevant vehicle maintenance manual if you need to remove the transmissionfrom the vehicle or carry out checks/ maintenance without removing it.
How to follow the explanations
Checks
The only checks explained in this manual are those for which special tools or measuring instruments are used. Generalvisual checks and cleaning of components are not explained, but this constitutes essential maintenance and must becarried out.
AK203434
Maintenance Procedures
(1)At the beginning of each section there are component drawings to enable you to grasp how they are fitted.(2)Numbers on these drawings denote the order for maintenance procedures, The drawings also show parts
that cannot be re-used, and tightening torques.• Removal order:
The numbers before the part names given in the removal order correspond to the numbers in thecomponent drawings, and denote the order in which they are removed.
• Fitting order:If the order in which they are fitted is simply the reverse of the order in which they were removed, thefitting order is omitted.
• Dismantling order:The numbers before the part names given in the dismantling order correspond to the numbers in thecomponent drawings, and denote the order in which they are dismantled.
• Assembly order:If the order in which they are assembled is simply the reverse of the dismantling order, the assembly orderis omitted.
Categorisation of Key Maintenance Points
Key points for maintenance/maintenance = key point concerning removing/dismantlingstandards / use of special tools are >>A
8/17/2019 Manual Transmàssion 6 speed.pdf
4/55
CLUTCH - HOW TO FOLLOW THIS MANUAL 21-3
These symbols/letters correspond with symbols/letters inremoval / fitting / dismantling / assembling order
Explains procedure / precautionsrequired when removing / fitting / dismantling / assembling.
Piston Piston caps
Dismantling Order1.Lock pin2.Interlock plate3.Control finger4.Pin
>>A>A
8/17/2019 Manual Transmàssion 6 speed.pdf
5/55
CLUTCH - SPECIFICATIONS21-4
Specifications M1212000200137Item Specification
Type Dry single plate typeClutch discFacing dimensions (mm) 240 x 160Type Diaphragm spring pull typeClutch coverSet load (N) 9320
Clutch control method Hydraulic
Maintenance Standards M1212000300101Item Limit (mm)Clutch disc facing rivet sinkage 0.3Clutch diaphragm spring tip height variation 0.5
Tightening Torques M1212001800109Item Tightening Torque (N • m)Clutch tube flare nut 15± 2Clutch fluid line bracket bolt 18± 3Clutch release cylinder fitting bolt 18± 3Clutch release fork shaft fitting bolt 9.8± 2.0Clutch release cylinder union bolt 22 ± 2Clutch cover bolt 18± 3Clutch release cylinder air breather 11± 1
Lubricants M1212000400119Item BrandRelease fork and release cylinder push rod contact surfacesRelease fork and release shaft sliding sectionRelease fork and release bearing contact surfaces
0101011 or equivalent
Whole of piston and piston capsInside of release cylinder 4 or equivalent
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
6/55
CLUTCH - CLUTCH 21-5
CLUTCH
Removal / Fitting
RemovalOrder Removal Order (continued)1. Clutch fluid line bracket >>C>B>E>A>E>D
8/17/2019 Manual Transmàssion 6 speed.pdf
7/55
CLUTCH - CLUTCH21-6
KEY POINTS FOR FITTING
>>A>B>C>D
8/17/2019 Manual Transmàssion 6 speed.pdf
8/55
CLUTCH - CLUTCH 21-7
>>E
8/17/2019 Manual Transmàssion 6 speed.pdf
9/55
8/17/2019 Manual Transmàssion 6 speed.pdf
10/55
CLUTCH - CLUTCH RELEASE CYLINDER 21-9
KEY POINT FOR ASSEMBLING
>>A
8/17/2019 Manual Transmàssion 6 speed.pdf
11/55
8/17/2019 Manual Transmàssion 6 speed.pdf
12/55
22-1
CHAPTER 22
MANUAL TRANSMISSIONCONTENTS
Overview ...............................................22-2
Specifications .......................................22-3
Maintenance Standards .......................22-4
Sealants/Adhesives ..............................22-4
Lubricants .............................................22-4
Adjustment Shims, ThrustWashers, Snap Rings ...........................22-5
Tightening Torques ..............................22-6
Special Tools.........................................22-7
Transmission.......................................22-10Dismantling/Assembling.................................22-10Checks...........................................................22-21
Input Shaft ...........................................22-22Dismantling/Assembling.................................22-22Checks ...........................................................22-28
Reverse Idler Gear..............................22-30Dismantling/Assembling.................................22-30Checks ...........................................................22-32
Clutch Housing ...................................22-34Dismantling/Assembling.................................22-34
Transmission Case .............................22-37Dismantling/Assembling.................................22-37
Centre Differential...............................22-39Dismantling/Assembling.................................22-39
Transfer................................................22-43Dismantling/Assembling.................................22-43
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
13/55
MANUAL TRANSMISSION - OVERVIEW22-2
OVERVIEW
Cross Section (Transmission)
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
14/55
MANUAL TRANSMISSION - SPECIFICATIONS 22-3
Cross Section (Transfer)
SPECIFICATIONSM1222000200150
Transmission Type Table
1st gear 2.909
2nd gear 1.944
3rd gear 1.434
4th gear 1.100
5th gear 0.868
6th gear 0.693
Reverse 2.707
Transmission Type Speedometer GearRatio?
Final ReductionGear Ratio
FrontLSD?
VehicleType
EngineType
W6MAA-1-GFNF No 4-583 Yes CT9A 4G63-I/C-T/C
Gear Ratio Table
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
15/55
MANUAL TRANSMISSION - MAINTENANCE STANDARDS22-4
Maintenance Standards
Liquid Gaskets (Flow-In-Place Gasket)On this transmission FIPG is used in severalassemblies. For the liquid gasket to fully achieve its
objectives, careful attention needs to be paid to theamount used, the application procedure, and thecondition of the surfaces on which it is applied.Not using enough will result in leakage, while if toomuch is used it will overflow and block or constrict theoil passages. Hence, to prevent leakage from joints, itis absolutely essential to apply the correct amountand leave no gaps.
DismantlingParts assembled using FIPG can be dismantledeasily; no special method is required. However, insome cases you may need to tap it with a woodenmallet or similar tool to break the sealant between themating surfaces.
Cleaning the Gasket SurfaceCompletely remove all material adhering to matingsurfaces using a gasket scraper. Make sure that the
surfaces on which the FIPG will be applied aresmooth. There must be no oil, grease or othersubstances adhering to mating surfaces. Do notforget to remove any old FIPG from fitting holes,screw holes.
Application ProcedureApply the FIPG within the specified diameter, leavingno gaps. Make sure it is applied all the way aroundfitting holes. Before it solidifies FIPG can be wipedoff. Fit the specified sections together while it is stillwet (within 10 minutes). Make absolutely sure that itonly adheres to the areas where it is needed. Do notput any oil or water on the parts after fitting themtogether, or drive the car, until sufficient time (about 1hour) has elapsed.The procedure for applying FIPG varies fromassembly to assembly, so be sure to use theprocedure described here.
LubricantsM1222000400091
Sealants / Adhesives
Item Standard (mm) Limit (mm)Differential side bearing pre-load 0.15 to 0.20 -Input shaft end play 0 to 0.06 -Main shaft end play 0 to 0.06 -
Reverse idler gear end play 0.04 to 0.10 -Distance between input shaft front bearing and thrust washer 167.6 to 167.7 -Input shaft 6th gear bush end play 0 to 0.1 -Wear on one side of shift fork claws - 0.2Clearance between synchroniser ring and gear - 0.7Clearance between synchroniser ring and synchroniser cone - 0.2Backlash on differential side gear and pinion 0.025 to 0.150 -
Item BrandClutch housingÅÃtransaxle case mating surfaces MZ100077 or equivalentReverse switch MZ100077 or equivalentAir breather MZ100055 or equivalentDifferential drive gear bolt 0110106 or Locktight 648 or equivalent
Item BrandLip on transfer oil seal Sunlight No. 2 or Retinax A or equivalentO-rings
M1222000300135
M1222000500128
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
16/55
MANUAL TRANSMISSION - ADJUSTMENT SHIMS, THRUST WASHERS, SNAP RI NGS 22-5
ADJUSTMENT SHIMS, THRUST WASHERS,SNAP RINGS
M1222012000142
Shims (for adjusting differential side bearing pre-load)
Thickness (mm)Thickness (mm)
0.48 0.720.52 0.760.56 0.800.60 0.840.64 0.880.68 0.92
Shims (for adjusting input shaft end play)Thickness (mm) Thickness (mm)0.44 1.000.48 1.04
0.52 1.080.56 1.120.60 1.160.64 1.200.68 1.240.72 1.280.76 1.320.80 1.360.84 1.400.88 1.440.92 1.480.96 1.52
Shims (for adjusting main shaft end play)Thickness (mm) Thickness (mm)0.44 0.800.48 0.840.52 0.880.56 0.920.60 0.960.64 1.000.68 1.040.72 1.080.76
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
17/55
MANUAL TRANSMISSION - TIGHTENING TORQUES22-6
Shims (for adjusting reverse idler gear end play)Thickness (mm) Thickness (mm)1.76 2.241.80 2.281.84 2.321.88 2.361.92 2.40
1.96 2.442.00 2.482.04 2.522.08 2.562.12 2.602.16 2.642.20
Thrust Washers (for adjusting distance between input shaft front bearing and thrust washer)Thickness (mm) Thickness (mm)3.84 4.023.90 4.08
3.96 4.14Snap Rings (for adjusting input shaft 6th gear bush end play)Thickness (mm) Thickness (mm)1.71 2.011.76 2.061.81 2.111.86 2.161.91 2.211.96 2.26
TIGHTENING TORQUESItem Tightening Torque (Nm)Transfer bolt 70 ± 10Roll stopper bracket bolt 69 ± 9Vehicle speed sensor bolt 11 ± 1Reverse switch 28 ± 5Stopper bolt 29 ± 1Shift check plug 15 ± 2Transaxle case bolt (with sealant) 63 ± 1
Transaxle case bolt 52 ± 1Shift check plug 15 ± 2Reverse lever assembly 14 ± 1Main shaft bearing retainer bolt 7.3± 1.0Drain plug 35 ± 4Filler plug 35 ± 4
M1222013900052
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
18/55
MANUAL TRANSMISSION - TOOLS 22-7
SPECIAL TOOLSM1222000600147
Item Tightening Torque (Nm)
Differential drive gear bolt 132 ± 5
Transfer cover case bolt 23 ± 3
Plug 30 ± 2
Magnet plug 30 ± 2
Tool Number Name Purpose
MB9908910 Side bearing puller Used together withclaws
MB991967 Claws Removal of differentialside bearing outerrace
MB991968 Bridge Removal of differentialside bearing outerrace
MB991969 Measurement adaptor Differential sidebearing pre-loadmeasurement
MB991966 Bearing outer raceinstaller
Fitting differential sidebearing outer race
MD998801 Bearing remover Fitting/removal ofgears, bearings andsleeves
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
19/55
MANUAL TRANSMISSION - SPECIAL TOOLS22-8
Tool Number Name Purpose
MD998917 Bearing remover Fitting/removal ofgears, bearings andsleeves
MD998812 Installer cap Used together withinstaller/ installeradapter
MD998813 Installer 100 Used with installercap / installer adaptor
MD998818 Installer adaptor (38) Fitting input shaft rearbearing / rollerbearing inner race
MD998823 Installer adaptor (48) Fitting 3rd – 4th gearsynchroniser
assembly
MD998822 Installer adaptor (46) Fitting 1st gear sleeve / 1st – 2nd gearsynchroniser hub
MB990938 Handle Used together withinstaller adaptor
MD998323 Bearing installer Fitting input shaft oilseal
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
20/55
MANUAL TRANSMISSION - SPECIAL TOOLS 22-9
Tool Number Name Purpose
MD998800 Oil seal installer Fitting differential oilseal and transfer oilseal
MB990936 Installer adaptor Fitting transfertapered roller bearingand transfer oil seal
MB990937 Installer adaptor Fitting transfer oil seal
MB990887 Arm bush adaptor &installer ring
Fitting transfer oil seal
MB990891 Bush remover &installer base
Used together witharm bush adaptor and
installer ring
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
21/55
MANUAL TRANSMISSION - TRANSMISSION22-10
TRANSMISSION
Dismantling / Assembling
Dismantling Order Dismantling Order (continued)1. Transfer 7. Bore plug2. O-ring 8. Stopper bolt3. Front roll stopper bracket >>O>P
8/17/2019 Manual Transmàssion 6 speed.pdf
22/55
MANUAL TRANSMISSION - TRANSMISSION 22-11
Dismantling Order Dismantling Order (continued)>>N>K>M>J>J>J>M>J>J>M>J>L
8/17/2019 Manual Transmàssion 6 speed.pdf
23/55
MANUAL TRANSMISSION - TRANSMISSION22-12
Dismantling Order Dismantling Order (continued)27. Reverse lever assembly 51. Interlock balls28. Shifter cap 52. Shift check sleeve29. Reverse fork rod 53. Main shaft assembly30. Reverse shift fork 54. Input shaft assembly31. Retaining pin 55. Reverse idler gear assembly32. Reverse bracket 56. Centre differential33. Reverse bracket fork rod Assembly Order34. Interlock balls 56. Centre differential35. Retaining pin >>A>A>A>B>C>D>D>D>D>D>E>F
8/17/2019 Manual Transmàssion 6 speed.pdf
24/55
MANUAL TRANSMISSION - TRANSMISSION 22-13
Assembly Order (cont.) Assembly Order (cont.)47. Interlock pin >>H>F>F>F>F>I>G>H>A
8/17/2019 Manual Transmàssion 6 speed.pdf
25/55
MANUAL TRANSMISSION - TRANSMISSION22-14
When fitting assembly, make sure that you donot scratch input idler shaft seal (Wind plastictape around spline of input shaft assembly).2. Insert input shaft assembly first, then main shaft
assembly, so that they rest lightly (literally ‘float’)on clutch housing.
Match up lock pin at tip of reverse idler gearassembly with grooved location on clutch housing,and fit this assembly.3. Fit reverse idler gear assembly between input
shaft and main shaft assemblies, which areresting lightly on clutch housing, then fit all 3 intoit at the same time.
>>B>C
8/17/2019 Manual Transmàssion 6 speed.pdf
26/55
MANUAL TRANSMISSION - TRANSMISSION 22-15
>>D>E>F
8/17/2019 Manual Transmàssion 6 speed.pdf
27/55
8/17/2019 Manual Transmàssion 6 speed.pdf
28/55
8/17/2019 Manual Transmàssion 6 speed.pdf
29/55
MANUAL TRANSMISSION - TRANSMISSION22-18
Measure dimensions at 3 optional points onouter race. Check whether outer race ishorizontal before measuring.(3)Using a height gauge, measure distance from
differential side bearing outer race to transaxlefitting surface on clutch housing (Dimension L2).
>>L>M
8/17/2019 Manual Transmàssion 6 speed.pdf
30/55
MANUAL TRANSMISSION - TRANSMISSION 22-19
(2) Put solder (length about 10mm, diameter1.6mm) on transaxle case at locations shown indrawing (main shaft rear bearing fitting area).
(3) Put solder (length about 10mm, diameter1.6mm) on transaxle case locations shown indrawing (reverse idler bosses).
(4) Temporarily locate snap ring on main shaft rearbearing area of transaxle case.
(5) With snap ring temporarily located on main shaft
bearing area, open out snap ring to make itbigger than the bore plug fitting hole, and puttransaxle onto clutch housing.
For this operation, use the transaxle case boltsyou remove.(6) Tighten fitting bolts to specified torque.
For this operation, use the O-ring you remove.(7) Fit control assembly and tighten fitting bolts to
specified torque.(8) Shift to 2nd gear, lift up main shaft, and fit snap
ring securely to main shaft rear bearing.Comment: See control assembly fitting sectionfor how to shift gears.
(9) Return control assembly to neutral position andremove fitting bolts. Then remove controlassembly.(10)Remove transaxle case.
(11) Remove snap ring from main shaft rear bearing,then remove transaxle case.
(12)Remove solder, measure thickness of squashedsolder using a micrometer, and select shimswhich will give the appropriate end play.
Comment: If solder has not been squashed, repeatoperations (1) to (11) using solder with a larger diameter.Input shaft end play: standard thickness: 0 – 0.06 mmMain shaft end play: standard thickness: 0 – 0.06 mmReverse idler gear end play: standard thickness:0.04 – 0.10mm
Care required
Care required
Solder
Solder
Bolt coloursA: yellowB: black
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
31/55
MANUAL TRANSMISSION - TRANSMISSION22-20
>>N>O>P
8/17/2019 Manual Transmàssion 6 speed.pdf
32/55
MANUAL TRANSMISSION - TRANSMISSION 22-21
ChecksM1222001100123
Reversing light switch1. Check current between terminals.
Item LivePress switch Yes
Release switch No2. If there is a fault, check the reversing light switch.
Fork rod / Reverse lever assembly / Shift fork1. Check for wear, scratches, warping or other
abnormalities on contact and sliding surfaces. Ifanything is abnormal replace that part (if the onlyproblem is extent of contact, replacement is notnecessary).
2. Check width of claws on shift fork (section thatslides against coupling sleeve), make sure it is notabove the limit.
Item Limit for wearon 1 side (mm)
Sliding widthwhen new (mm)
1st-2nd gear 0.2 7.80 to 7.93
3rd-4th gear 0.2 7.80 to 7.93
5th-6th gear 0.2 6.10 to 6.23
Reverse 0.2 12.80 to 12.93
Fork rod
Reverse lever assembly
Shift fork
Sliding widthwhen new
Wear on one sideWear on one side
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
33/55
MANUAL TRANSMISSION - INPUT SHAFT22-22
INPUT SHAFT
Dismantling / Assembling
Dismantling Order Dismantling Order (cont.) >>K>J>I>D>C>H>B>G>B>G>B>G>B>G>F>E>A
8/17/2019 Manual Transmàssion 6 speed.pdf
34/55
8/17/2019 Manual Transmàssion 6 speed.pdf
35/55
MANUAL TRANSMISSION - INPUT SHAFT22-24
Removing ball bearingUsing the bearing remover (Special tool No.MD998801), remove ball bearing.
Key Points for Assembly>>A>B
8/17/2019 Manual Transmàssion 6 speed.pdf
36/55
8/17/2019 Manual Transmàssion 6 speed.pdf
37/55
MANUAL TRANSMISSION - INPUT SHAFT22-26
>>F>G>H
8/17/2019 Manual Transmàssion 6 speed.pdf
38/55
MANUAL TRANSMISSION - INPUT SHAFT 22-27
>>I>J>K
8/17/2019 Manual Transmàssion 6 speed.pdf
39/55
MANUAL TRANSMISSION - INPUT SHAFT22-28
ChecksM1222001700114Input ShaftThere must be no scratching, peeling, gouging,uneven wear, warping or other abnormalities on theinput shaft.
Gears1. There must be no scratching or wear on the
helical gears or clutch gear teeth sides for any ofthe gears.
2. There must be no surface roughness, scratchingor wear on the synchroniser cones of any of thegears (excluding 3rd).
3. There must be no scratching or wear on the insidediameters or front/rear surfaces of any of thegears.
Needle bearing1. When the input shaft, sleeve and gears are
assembled and rotated, they must rotatesmoothly, with no play orabnormal noise.
2. The retainers must not be deformed.
Single cone synchroniser ring1. There must be no scratching or damage on the
synchroniser ring clutch gear.2. There must be no scratching, wear or squashed
threads on the inside diameter of the synchroniserring cone.
3. There must be no scratching, damage orexcessive wear on the synchroniser ring⇔
synchroniser key contact surface.
4. Push synchroniser ring up against gear cone, andcheck Clearance A. If clearance is below limit,replace.Limit: 0.7 mm
GearsSynchroniserring
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
40/55
MANUAL TRANSMISSION - INPUT SHAFT 22-29
Double cone synchroniser ring1. There must be no scratching / damage on the
outer synchroniser ring clutch gear.2. There must be no scratching / wear / squashed
threads on any of the synchroniser ring⇔synchroniser cone contact surfaces.
3. There must be no scratching, damage orexcessive wear on the outer synchroniser ring⇔synchroniser key contact surfaces.
4. Assemble the synchroniser rings and synchronisercones and check Clearances ‘A’ and ‘B’ on thedrawing. If either is over limit, replace.
Limit: 0.2 mm
Synchroniser keyThere must be no scratching or abnormal wear onthe synchroniser key € synchroniser hub contactsurfaces.
Synchroniser springSynchroniser springs must not be weakened,deformed or damaged.
Inner synchronizer ring
Synchroniser cone
Inner synchronizer ring
Synchroniser cone
Outer synchronizer ring
Outer synchronizer ring
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
41/55
MANUAL TRANSMISSION - REVERSE IDLER GEAR22-30
REVERSE IDLER GEAR
Dismantling / Assembling
Dismantling Order Dismantling Order (continued)
1. Reverse idler gear (rear) 8. Thrust bearingassembly 9. Reverse idler gear (front)2. Reverse idler gear (rear) 10. Needle bearing
>>B>A
8/17/2019 Manual Transmàssion 6 speed.pdf
42/55
MANUAL TRANSMISSION - REVERSE IDLER GEAR 22-31
Key Points for Removing Removing reverse idler gear sleeve
Mating may be faulty if the splines are re-assembled at a different place when these partsare re-used.Mark the reverse idler gear sleeve and hub toindicate where they must be re-assembled
Key Points for Assembly>>A>B
8/17/2019 Manual Transmàssion 6 speed.pdf
43/55
MANUAL TRANSMISSION - REVERSE IDLER GEAR22-32
Reverse Idler Gear ChecksM1222012400021Reverse idler shaftThere must be no scratching, peeling, gouging,uneven wear, warping or other abnormalities onreverse idler shaft.
Thrust bearing1. When the thrust bearing is assembled with the
washer and rotated, rotation must be smooth andthere must be no play or abnormal noise.
2. Retainers must not be deformed.
Needle bearing1. When reverse idler shaft and gear are assembled
and rotated, rotation must be smooth and theremust be no play or abnormal noise.
2. Retainers must not be deformed.
Reverse idler gear (front)1. There must be no scratching or wear on the
reverse idler gear, helical gears or clutch gearteeth sides.
2. There must be no roughness, scratching or wearon reverse idler gear synchroniser cone surface.
3. There must be no scratching or wear on the insidediameter or the front or rear surfaces of thereverse idler gear.
Synchroniser ring1. There must be no scratching or damage on the
synchroniser ring clutch gear.2. There must be no scratching, wear or squashed
threads on the inside diameter of the synchroniserring cone.
3. There must be no scratching, damage or
excessive wear on the synchroniser ring⇔synchroniser key contact surface.
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
44/55
MANUAL TRANSMISSION - REVERSE IDLER GEAR 22-33
4. Push synchroniser ring up against reverse idlergear cone and check Clearance ‘A’. If it is belowlimit, replace.Limit: 0.7 mm
When re-assembling the reverse idler gearsleeve and the and the reverse idler gear, youmust match up the marks made when they weredismantled.
1. When you have re-assembled the reverse idlergear sleeve and hub, slide them against eachother. They must slide smoothly, not stick orcatch.
2. There must be no scratching on the front or rearends inside the reverse idler gear sleeve.
3. There must be no scratching or wear on thehelical gears of the reverse idler gear or the clutchgear teeth sides.
4. There must be no scratching or wear on the insidediameter or front or rear surfaces of the reverseidler gear.
Care required
Reverseidler gear
Synchroniserring
Marks
Reverseidler gear
Reverse idlergear sleeve
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
45/55
MANUAL TRANSMISSION - CLUTCH HOUSING22-34
CLUTCH HOUSING
Dismantling / Assembling
Dismantling Order Dismantling Order (continued)1. Magnet 7. Dowel pin
>>C>B>D>A
8/17/2019 Manual Transmàssion 6 speed.pdf
46/55
MANUAL TRANSMISSION - CLUTCH HOUSING 22-35
Key Points for Dismantling Removing differential side bearing outerrace1. Heat clutch housing to about 100˚C (maximum
120˚C).
2. Remove differential side bearing outer race, usingthe following special tools:
• Side bearing puller (MB990810)• Claws (MB991967)• Bridge (MB991968)
Key Points for Assembly>>A>B
8/17/2019 Manual Transmàssion 6 speed.pdf
47/55
MANUAL TRANSMISSION - CLUTCH HOUSING22-36
>>C>D
8/17/2019 Manual Transmàssion 6 speed.pdf
48/55
22-37
TRANSMISSION CASE
Dismantling / Assembling
Dismantling Order Dismantling Order (continued)>>C>C>B>A>A
8/17/2019 Manual Transmàssion 6 speed.pdf
49/55
MANUAL TRANSMISSION - TRANSMISSION CASE22-38
>>B>C
8/17/2019 Manual Transmàssion 6 speed.pdf
50/55
MANUAL TRANSMISSION - CENTRE DIFFERENTIAL 22-39
CENTRE DIFFERENTIAL
Dismantling / Assembling
AK204087AB
Dismantling Order Dismantling Order (continued)>>D>B>B>C>B>B>B>B>B>B>B>A>B>B>B
8/17/2019 Manual Transmàssion 6 speed.pdf
51/55
8/17/2019 Manual Transmàssion 6 speed.pdf
52/55
MANUAL TRANSMISSION - CENTRE DIFFERENTIAL 22-41
2. Fit washers on rear surface of pinion and engage4 pinions to side gear. Rotate them and locatecorrectly, then fit the pinion shaft holder.
3. Insert the pinion shafts.
4. Fit lock pins in direction indicated in drawing.
5. Fit front output shaft to side gear and fit snap ring.6. Fit spacer to side gear, then the fit side gear
inside the centre differential case.NB: If fitting a new side gear, use a mediumthickness (0.66 ~ 0.73 mm) spacer.
7. Align marks made when dismantling, fit centredifferential flange and temporarily tighten machinescrews (4 places).
8. Measure backlash on side gear and pinion.Standard range: 0.025 ~ 0.150 mm
9. If backlash is outside standard range, select aspacer, fit it and re-measure backlash.NB: Adjust till backlash is the same on both sides.
Washer
Differential case
Spacer
Marks
Lock pin
Pinion gear
http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/http://www.workshopmanuals.co.uk/
8/17/2019 Manual Transmàssion 6 speed.pdf
53/55
MANUAL TRANSMISSION - CENTRE DIFFERENTIAL22-42
>>C>D
8/17/2019 Manual Transmàssion 6 speed.pdf
54/55
MANUAL TRANSMISSION - TRANSFER 22-43
TRANSFER
Dismantling / Assembling
Dismantling Order Dismantling Order (continued)1. Dust shield guard >>B>F>A>E>D>A>C>A
8/17/2019 Manual Transmàssion 6 speed.pdf
55/55
MANUAL TRANSMISSION - TRANSFER22-44
>>B>C>D>E>F