M9000-700 Universal Ball Valve Linkage Kit Product Bulletin
1
The M9000-700 Universal Ball Valve Linkage Kit is designed specifically for field mounting Johnson Controls® VA(M)9203 and VA(M)9208 Series Spring Return and VA9104 and VA(M)9310 Series Non-Spring Return Actuators to ball valves from various manufacturers in sizes from ½ inch to 2 inches.
These sturdy linkage kits provide easy and stable actuator mounting while preventing loading on the valve stem and stem seals, to ensure longer seal life.
Figure 1: M9000-700 linkage kit
Table 1: Features and benefitsFeatures BenefitsModular design of shaft and actuator Allows universal use on ball valves of several manufacturersSturdy zinc-plated steel shaft and connector Provides exceptional strength and stability which ensures long life even at
high torques on valves from 1/2 inch up to two inchesGlass-reinforced thermoplastic resin spacer Reduces temperature and condensation from the valve to the actuatorNo special tools required to install Facilitates quick and easy installationTested for 100,000 full cycles Assures long time reliability on valves from 1/2 inch up to two inches
M9000-700 Universal Ball Valve Linkage KitProduct BulletinM9000-700 Code No. LIT-12012960
Issued October 2021
2
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin
Product guidelinesInstall the M90000-700 Universal Ball Valve Linkage kit with the actuator at or above the centerline of the horizontal piping.
To minimize heat transfer in steam applications, wrap the valve and piping with insulation. Allow sufficient clearance to remove the actuator (as illustrated in Figure 2 through Figure 6).
Before installing the electric actuator, use an adjustable wrench to manually rotate the valve stem several times. Rotating the valve stem breaks the torque that may have built up during long-term storage..
For detailed installation instructions, refer to the M9000-700 Universal Ball Valve Linkage Kit Installation Instructions (Part No. 14-88360-03427).
Contact the nearest Johnson Controls representative for compatibility concerns before using the M9000-700 linkage kit on valves which are not listed in the selection charts in Table 2 to Table 9.
When servicing the electric actuator or the piping system:• disconnect the power supply to the actuator before servicing.• relieve the pressure in the piping system.
Linkage kit selectionUse the M9000-700 linkage kit to field mount Johnson Controls VA9203 and VA9208 Series Spring Return actuators and VA9104 and VA9310 Series Non-Spring Return actuators to the valves listed in the selection charts.
The sturdy and modular design of the linkage maintains accurate stem alignment, eliminates sideloading on the valve stem and improves stem seal positioning to ensure longer seal life. The linkage kit material and overall height, as well as piping insulation, minimize heat transfer to the electric actuator in higher temperature fluid applications.
IMPORTANT: Do not exceed the operating conditions as indicated by the valve manufacturer.
IMPORTANT: In steam applications, install the valve with the stem horizontal to the piping. Failure to follow these guidelines may shorten the life of the actuator.
IMPORTANT: Do not cover the actuator with thermal insulating material. High ambient temperatures may damage the actuator, and a hot water pipe, a steam pipe, or other heat source may overheat it.
IMPORTANT: Wire the actuators in accordance with applicable electrical code requirements. Wire the input lines to the electric actuator correctly so that the valve moves in the proper direction. Do not exceed the actuator's electrical rating.
IMPORTANT: Protect the actuator from dripping water, condensation, and other moisture. Water or moisture could result in an electrical short, which may damage or affect the operation of the actuator.
Risk of electric shock.Disconnect the power supply before making electrical connections. Contact with components carrying hazardous voltage can cause electric shock and may result in severe personal injury or death.
Risk of personal injury and property damageDo not apply power to the system before checking all wiring connections. Short circuited or improperly connected wires may result in permanent damage to the equipment,
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin3
Selection charts for Johnson Controls actuators on ball valvesTable 2: Belimo B2 and B3 series ball valves
Body type Body size (inches)
Chrome plated brass ball, nickel plated stem
Stainless steel ball and
stem
High temperature ball
vales
Compatible JCI actuator1
1. For VA9208 and M9208, use two field furbished #10-24 x 3 1/2 in. screws and two locking nuts #10-24. For M9310, use the M9310-500 transformation kit.For M9203 and M9208, use the M9000-560 transformation kit.
Two-way
1/2 in.
B207BB208BB209BB210BB211BB212BB213BB214BB215BB216B
B207B208B209B210B211B212B213B214B215B216
B215HT029B215HT046B215HT073B215HT116B215HT186
VA9203 spring return
VA9208 spring return
VA9104 non- spring return
VA9310 non- spring return
M9203 spring return
M9208 spring return
M9310 non- spring return
3/4 in.
B217BB218BB219BB220B
B217B218B219B220
B220HT290B220HT464B220HT731B220HT928
B220HT1320
B221B B221
VA9208 spring return
VA9310 non- spring return
M9208 spring return
M9310 non- spring return
1 in.
B222B223B224B225
B225HT464B225HT731B225HT1160B225HT1856B225HT2800
1 1/4 in.
B229B230B231B232
Three-way
1/2 in.
B307BB308BB309BB310BB311BB312BB313BB315B
B307B308B309B310B311B312B313B315
VA9203 spring return
VA9208 spring return
VA9104 non- spring return
VA9310 non- spring return
M9203 spring return
M9208 spring return
M9310 non- spring return
3/4 in.
B317BB318BB320BB321B
B317B318B320B321
1 in.
B322B332B325
VA9208 spring return
VA9310 non- spring return
M9208 spring return
M9310 non- spring return
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin4
Table 3: Bray commercial ST series
Body size (inches) Two-way ST series Three-way ST series Compatible JCI actuator1
1. For VA9208 and M9208, use two field furbished #10-24 x 3 1/2 in. screws and two locking nuts #10-24. For M9208, use the M9000-560 transformation kit.For ST2 Series valves, the M9000-700 Universal Ball Valve Linkage kit is not required.
1/2 in.
ST-05-2-004ST-05-2-007ST-05-2-01ST-05-2-003ST-05-2-05ST-05-2-08ST-05-2-12
ST-05-3-003ST-05-3-006ST-05-3-01ST-05-3-02ST-05-3-04ST-05-3-08
VA9208 spring return
VA9310 non- spring return
M9208 spring return
M9310 non- spring return
3/4 in.
ST-75-2-003ST-75-2-006ST-75-2-01ST-75-2-03ST-75-2-04ST-75-2-10ST-75-2-15ST-75-2-29
ST-75-3-004ST-75-3-007ST-75-3-01ST-75-3-02ST-75-3-04ST-75-3-13
1 in.
ST-1-2-004ST-1-2-009ST-1-2-15ST-1-2-26ST-1-2-44ST-1-2-54
ST-1-3-004ST-1-3-007ST-1-3-01ST-1-3-02ST-1-3-04ST-1-3-05ST-1-3-09ST-1-3-10ST-1-3-15ST-1-3-22ST-1-3-31
1 1/4 in.
ST-125-2-04ST-125-2-08ST-125-2-15ST-125-2-37ST-125-2-41ST-125-2-102
ST-125-3-04ST-125-3-08ST-125-3-09ST-125-3-13ST-125-3-19ST-125-3-34
1 1/2 in.
ST-150-2-23ST-150-2-41ST-150-2-74ST-150-2-171
ST-150-3-04ST-150-3-08ST-150-3-13ST-150-3-24ST-150-3-32ST-150-3-61
2 in.
ST-2-2-41ST-2-2-57ST-2-2-71ST-2-2-100ST-2-2-210ST-2-2-266
ST-2-3-24ST-2-3-38ST-2-3-57ST-2-3-109
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin5
Table 4: Griswold controls unimizer series valves
Body type
Body size
(inches)
NPT threaded, std stem and ball
NPT threaded, stainless
steel stem and ball
BSPP threaded, std stem and ball
BSPP threaded, stainless
steel stem and ball
Lead free, std stem and
ball
Lead free stainless
steel stem and
ball
Compatible JCI actuator1
1. For VA9208 and M9208, use two field furbished #10-24 x 3 1/2 in. screws and two locking nuts #10-24. For M9310, use the M9310-500 transformation kit.For M9203 and M9208, use the M9000-560 transformation kit.
Two-way
1/2 in.
UR2A1FBUR2A2FBUR2A3FBUR2A4FBUR2A5FBUR2A6FBUR2A7FB
UR2A1FSUR2A2FSUR2A3FSUR2A4FSUR2A5FSUR2A6FSUR2A7FS
UR2A1BBUR2A2BBUR2A3BBUR2A4BBUR2A5BBUR2A6BBUR2A7BB
UR2A1BSUR2A2BSUR2A3BSUR2A4BSUR2A5BSUR2A6BSUR2A7BS
UR2A1LBUR2A2LBUR2A3LBUR2A4LBUR2A5LBUR2A6LBUR2A7LB
UR2A1LSUR2A2LSUR2A3LSUR2A4LSUR2A5LSUR2A6LSUR2A7LS
VA9203 spring return
VA9208 spring return
VA9104 non-
spring return
VA9310 non-
spring return
M9203 spring return
M9208 spring return
M9310 non-
spring return
3/4 in.
UR2B1FBUR2B2FBUR2B3FBUR2B4FBUR2B5FBUR2B6FBUR2B7FBUR2B8FB
UR2B1FSUR2B2FSUR2B3FSUR2B4FSUR2B5FSUR2B6FSUR2B7FSUR2B8FS
UR2B1BBUR2B2BBUR2B3BBUR2B4BBUR2B5BBUR2B6BBUR2B7BBUR2B8BB
UR2B1BSUR2B2BSUR2B3BSUR2B4BSUR2B5BSUR2B6BSUR2B7BSUR2B8BS
UR2B1LBUR2B2LBUR2B3LBUR2B4LBUR2B5LBUR2B6LBUR2B7LBUR2B8LB
UR2B1LSUR2B2LSUR2B3LSUR2B4LSUR2B5LSUR2B6LSUR2B7LSUR2B8LS
1 in.
UR2C1FBUR2C2FBUR2C3FBUR2C4FBUR2C5FBUR2C6FBUR2C7FB
UR2C1FSUR2C2FSUR2C3FSUR2C4FSUR2C5FSUR2C6FSUR2C7FS
UR2C1BBUR2C2BBUR2C3BBUR2C4BBUR2C5BBUR2C6BBUR2C7BB
UR2C1BSUR2C2BSUR2C3BSUR2C4BSUR2C5BSUR2C6BSUR2C7BS
UR2C1LBUR2C2LBUR2C3LBUR2C4LBUR2C5LBUR2C6LBUR2C7LB
UR2C1LSUR2C2LSUR2C3LSUR2C4LSUR2C5LSUR2C6LSUR2C7LS
1 1/4 in.
UR2D1FBUR2D2FBUR2D3FBUR2D4FBUR2D5FBUR2D6FB
UR2D1FSUR2D2FSUR2D3FSUR2D4FSUR2D5FSUR2D6FS
UR2D1BBUR2D2BBUR2D3BBUR2D4BBUR2D5BBUR2D6BB
UR2D1BSUR2D2BSUR2D3BSUR2D4BSUR2D5BSUR2D6BS
UR2D1LBUR2D2LBUR2D3LBUR2D4LBUR2D5LBUR2D6LB
UR2D1LSUR2D2LSUR2D3LSUR2D4LSUR2D5LSUR2D6LS
1 1/2 in.
UR2E1FBUR2E2FBUR2E3FBUR2E4FB
UR2E1FSUR2E2FSUR2E3FSUR2E4FS
UR2E1BBUR2E2BBUR2E3BBUR2E4BB
UR2E1BSUR2E2BSUR2E3BSUR2E4BS
UR2E1LBUR2E2LBUR2E3LBUR2E4LB
UR2E1LSUR2E2LSUR2E3LSUR2E4LS
2 in.
UR2F1FBUR2F2FBUR2F3FBUR2F4FBUR2F5FBUR2F6FBUR2F7FB
UR2F1FSUR2F2FSUR2F3FSUR2F4FSUR2F5FSUR2F6FSUR2F7FS
UR2F1BBUR2F2BBUR2F3BBUR2F4BBUR2F5BBUR2F6BBUR2F7BB
UR2F1BSUR2F2BSUR2F3BSUR2F4BSUR2F5BSUR2F6BSUR2F7BS
UR2F1LBUR2F2LBUR2F3LBUR2F4LBUR2F5LBUR2F6LBUR2F7LB
UR2F1LSUR2F2LSUR2F3LSUR2F4LSUR2F5LSUR2F6LSUR2F7LS
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin6
Table 5: Griswold controls unimizer series valves (continued)
Body type
Body size (inches)
NPT threaded, std stem and ball
BSPP threaded, std stem and ball
NPT threaded,
new
BSP threaded, new
Compatible JCI actuator1
1. For VA9208 and M9208, use two field furbished #10-24 x 3 1/2 in. screws and two locking nuts #10-24. For M9310, use the M9310-500 transformation kit.For M9203 and M9208, use the M9000-560 transformation kit.
Three-way
1/2 in.
UR3AAFBUR3ABFBUR3ACFBUR3ADFBUR3AEFBUR3AFFB
UR3AABBUR3ABBBUR3ACBBUR3ADBBUR3AEBBUR3AFBB
3WRAAF3WRABF3WRACF3WRADF3WRAEF3WRAFF
3WRAAB3WRABB3WRACB3WRADB3WRAEB3WRAFB
VA9203 spring return
VA9208 spring return
VA9104 non-
spring return
VA9310 non-
spring return
M9203 spring return
M9208 spring return
M9310 non-
spring return
3/4 in.
UR3BAFBUR3BBFBUR3BCFBUR3BDFBUR3BEFBUR3BFFBUR3BGFB
UR3BABBUR3BBBBUR3BCBBUR3BDBBUR3BEBBUR3BFBBUR3BGBB
3WRBAF3WRBBF3WRBCF3WRBDF3WRBEF3WRBFF
3WRBAB3WRBBB3WRBCB3WRBDB3WRBEB3WRBFB
1 in.
UR3CAFBUR3CBFBUR3CCFBUR3CDFBUR3CEFBUR3CFFBUR3CGFBUR3CHFBUR3CJFBUR3CKFBUR3CMFB
UR3CABBUR3CBBBUR3CCBBUR3CDBBUR3CEBBUR3CFBBUR3CGBBUR3CHBBUR3CJBBUR3CKBBUR3CMBB
1 1/4 in.
UR3DAFBUR3DBFBUR3DCFBUR3DDFBUR3DEFBUR3DFFBUR3DGFB
UR3DABBUR3DBBBUR3DCBBUR3DDBBUR3DEBBUR3DFBBUR3DGBB
1 1/2 in.
UR3EAFBUR3EBFBUR3ECFBUR3EDFBUR3EEFBUR3EFFB
UR3EABBUR3EBBBUR3ECBBUR3EDBBUR3EEBBUR3EFBB
2 in.
UR3FAFBUR3FBFBUR3FCFBUR3FDFBUR3FEFB
UR3FABBUR3FBBBUR3FCBBUR3FDBBUR3FEBB
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin7
Table 6: Honeywell VBN series valves
Body type
Body size
(inches)
Plated brass trim, standard
base
Plated brass trim, low profile
Plated brass trim, MN/MS
DCA actuator bracket
Stainless steel trim,
standard base
Stainless steel trim, low
profile
Stainless steel trim, MN/MS
DCA actuator bracket
Compatible JCI actuator1
1. For VA9208 and M9208, use two field furbished #10-24 x 3 1/2 in. screws and two locking nuts #10-24. For M9310, use the M9310-500 transformation kit.For M9203 and M9208, use the M9000-560 transformation kit.
Two-way
1/2 in.
VBN2A000.38PAVBN2A000.68PAVBN2A001.30PAVBN2A002.00PAVBN2A002.60PAVBN2A004.70PAVBN2A008.00PAVBN2A011.70PA
VBN2A000.38PLVBN2A000.68PLVBN2A001.30PLVBN2A002.00PLVBN2A002.60PLVBN2A004.70PLVBN2A008.00PLVBN2A011.70PL
VBN2A000.38PXVBN2A000.68PXVBN2A001.30PXVBN2A002.00PXVBN2A002.60PXVBN2A004.70PXVBN2A008.00PXVBN2A011.70PX
VBN2A000.38SAVBN2A000.68SAVBN2A001.30SAVBN2A002.00SAVBN2A002.60SAVBN2A004.70SAVBN2A008.00SAVBN2A011.70SA
VBN2A000.38SLVBN2A000.68SLVBN2A001.30SLVBN2A002.00SLVBN2A002.60SLVBN2A004.70SLVBN2A008.00SLVBN2A011.70SL
VBN2A000.38SXVBN2A000.68SXVBN2A001.30SXVBN2A002.00SXVBN2A002.60SXVBN2A004.70SXVBN2A008.00SXVBN2A011.70SX
VA9203 spring return
VA9208 spring return
VA9104 non-
spring return
VA9310 non-
spring return
M9203 spring return
M9208 spring return
M9310 non-
spring return
3/4 in.
VB2N2000.31PAVB2N2000.63PAVB2N2001.20PAVB2N2002.50PAVBN2B004.30PAVBN2B007.40PAVBN2B010.10PAVBN2B041.70PAVBN2B029.00PA
VB2N2000.31PLVB2N2000.63PLVB2N2001.20PLVB2N2002.50PLVBN2B004.30PLVBN2B007.40PLVBN2B010.10PLVBN2B041.70PLVBN2B029.00PL
VB2N2000.31PXVB2N2000.63PXVB2N2001.20PXVB2N2002.50PXVBN2B004.30PXVBN2B007.40PXVBN2B010.10PXVBN2B041.70PXVBN2B029.00PX
VB2N2000.31SAVB2N2000.63SAVB2N2001.20SAVB2N2002.50SAVBN2B004.30SAVBN2B007.40SAVBN2B010.10SAVBN2B041.70SAVBN2B029.00SA
VB2N2000.31SLVB2N2000.63SLVB2N2001.20SLVB2N2002.50SLVBN2B004.30SLVBN2B007.40SLVBN2B010.10SLVBN2B041.70SLVBN2B029.00SL
VB2N2000.31SXVB2N2000.63SXVB2N2001.20SXVB2N2002.50SXVBN2B004.30SXVBN2B007.40SXVBN2B010.10SXVBN2B041.70SXVBN2B029.00SX
1 in.
VBN2C004.40PAVBN2C009.00PAVBN2C015.30PAVBN2C026.00PAVBN2C044.00PAVBN2C054.00PA
VBN2C004.40PLVBN2C009.00PLVBN2C015.30PLVBN2C026.00PLVBN2C044.00PLVBN2C054.00PL
VBN2C004.40PXVBN2C009.00PXVBN2C015.30PXVBN2C026.00PXVBN2C044.00PXVBN2C054.00PX
VBN2C004.40SAVBN2C009.00SAVBN2C015.30SAVBN2C026.00SAVBN2C044.00SAVBN2C054.00SA
VBN2C004.40SLVBN2C009.00SLVBN2C015.30SLVBN2C026.00SLVBN2C044.00SLVBN2C054.00SL
VBN2C004.40SXVBN2C009.00SXVBN2C015.30SXVBN2C026.00SXVBN2C044.00SXVBN2C054.00SX
1 1/4 in.
VBN2D004.40PAVBN2D008.30PAVBN2D014.90PAVBN2D025.00PAVBN2D037.00PAVBN2D041.00PAVBN2D102.00PA
VBN2D004.40PLVBN2D008.30PLVBN2D014.90PLVBN2D025.00PLVBN2D037.00PLVBN2D041.00PLVBN2D102.00PL
VBN2D004.40PXVBN2D008.30PXVBN2D014.90PXVBN2D025.00PXVBN2D037.00PXVBN2D041.00PXVBN2D102.00PX
VBN2D004.40SAVBN2D008.30SAVBN2D014.90SAVBN2D025.00SAVBN2D037.00SAVBN2D041.00SAVBN2D102.00SA
VBN2D004.40SLVBN2D008.30SLVBN2D014.90SLVBN2D025.00SLVBN2D037.00SLVBN2D041.00SLVBN2D102.00SL
VBN2D004.40SXVBN2D008.30SXVBN2D014.90SXVBN2D025.00SXVBN2D037.00SXVBN2D041.00SXVBN2D102.00SX
1 1/2 in.
VBN2E023.00PXVBN2E030.00PXVBN2E041.00PXVBN2E074.00PXVBN2E172.00PX
VBN2E023.00SXVBN2E030.00SXVBN2E041.00SXVBN2E074.00SXVBN2E172.00SX
VA9203 spring return
VA9310 non-
spring return
M9203 spring return
M9310 non-
spring return
2 in.
VBN2F042.00PXVBN2F057.00PXVBN2F071.00PXVBN2F100.00PXVBN2F108.00PXVBN2F201.00PXVBN2F266.00PX
VBN2F042.00SXVBN2F057.00SXVBN2F071.00SXVBN2F100.00SXVBN2F108.00SXVBN2F201.00SXVBN2F266.00SX
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin8
Table 7: Honeywell VBN Series Valves (continued)
Body type
Body size (inches)
Plated brass trim, standard base
Plated brass trim, low profile
Plated brass trim, MN/MS
DCA actuator bracket
Compatible JCI actuator1
1. For VA9208 and M9208, use two field furbished #10-24 x 3 1/2 in. screws and two locking nuts #10-24. For M9310, use the M9310-500 transformation kit.For M9203 and M9208, use the M9000-560 transformation kit.
Three-way
1/2 in.
VBN3A000.33PAVBN3A000.59PAVBN3A001.00PAVBN3A002.40PAVBN3A004.30PAVBN3A008.00PA
VBN3A000.33PLVBN3A000.59PLVBN3A001.00PLVBN3A002.40PLVBN3A004.30PLVBN3A008.00PL
VBN3A000.33PXVBN3A000.59PXVBN3A001.00PXVBN3A002.40PXVBN3A004.30PXVBN3A008.00PX
VA9203 spring return
VA9208 spring return
VA9104 non- spring
return
VA9310 non- spring
return
M9203 spring return
M9208 spring return
M9310 non- spring
return
3/4 in.
VBN3B000.40PAVBN3B000.66PAVBN3B001.30PAVBN3B002.40PAVBN3B003.80PAVBN3B007.00PAVBN3B011.00PA
VBN3B000.40PLVBN3B000.66PLVBN3B001.30PLVBN3B002.40PLVBN3B003.80PLVBN3B007.00PLVBN3B011.00PL
VBN3B000.40PXVBN3B000.66PXVBN3B001.30PXVBN3B002.40PXVBN3B003.80PXVBN3B007.00PXVBN3B011.00PX
1 in.
VBN3C000.40PAVBN3C000.65PAVBN3C001.30PAVBN3C002.30PAVBN3C003.50PAVBN3C004.50PAVBN3C008.60PAVBN3C014.90PAVBN3C022.00PAVBN3C031.00PA
VBN3C000.40PLVBN3C000.65PLVBN3C001.30PLVBN3C002.30PLVBN3C003.50PLVBN3C004.50PLVBN3C008.60PLVBN3C014.90PLVBN3C022.00PLVBN3C031.00PL
VBN3C000.40PXVBN3C000.65PXVBN3C001.30PXVBN3C002.30PXVBN3C003.50PXVBN3C004.50PXVBN3C008.60PXVBN3C014.90PXVBN3C022.00PXVBN3C031.00PX
1 1/4 in.
VBN3D004.10PAVBN3D008.70PAVBN3D012.70PAVBN3D019.40PAVBN3D027.00PAVBN3D034.00PA
VBN3D004.10PLVBN3D008.70PLVBN3D012.70PLVBN3D019.40PLVBN3D027.00PLVBN3D034.00PL
VBN3D004.10PXVBN3D008.70PXVBN3D012.70PXVBN3D019.40PXVBN3D027.00PXVBN3D034.00PX
1 1/2 in.
VBN3E004.00PXVBN3E008.30PXVBN3E013.40PXVBN3E024.00PXVBN3E032.00PXVBN3E061.00PX
VA9203 spring return
VA9310 non- spring
return
M9203 spring return
M9310 non- spring
return2 in.VBN3F024.00PXVBN3F038.00PXVBN3F057.00PXVBN3F083.00PXVBN3F109.00PX
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin9
Table 8: Siemens 599 series ball valves
Body size
(inches)
Two-way chrome-
plated ball with brass stem (old)
Two-way chrome-
plated ball with brass
stem (current)
Two- way stainless steel ball and stem
Three-way chrome-
plated ball with brass stem (old)
Three-way chrome-
plated ball with brass
stem (current)
Three-way stainless steel ball and stem
Compatible JCI actuator1
1. For VA9208 and M9208, use two field furbished #10-24 x 3 1/2 in. screws and two locking nuts #10-24. For M9310, use the M9310-500 transformation kit.For M9203 and M9208, use the M9000-560 transformation kit.
1/2 in.
599-10203599-10204599-10205599-10206599-10207599-10208
599-10300599-10301599-10302599-10303599-10304599-10305599-10306599-10307
599-10300S599-10301S599-10302S599-10303S599-10304S599-10305S599-10306S599-10307S
599-10250599-10251599-10252599-10253599-10254599-10255
599-10350599-10351599-10352599-10353599-10354599-10355599-10356599-10357
599-10350S599-10351S599-10352S599-10353S599-10354S599-10355S599-10356S599-10357S
VA9208 spring return
VA9310 non-
spring return
M9208 spring return
M9310 non-
spring return
3/4 in.599-10209599-10210
599-10308599-10309599-10310599-10311
599-10308S599-10309S599-10310S599-10311S
599-10256 599-10358599-10360
599-10358S599-10360S
1 in.
599-10211599-10212599-10213599-10214
599-10312599-10313599-10314599-10315599-10316
599-10312S599-10313S599-10314S599-10315S599-10316S
599-10257599-10258599-10259
599-10361599-10362599-10363
599-10361S599-10362S599-10363S
1 1/4 in.
599-10215599-10216599-10217
599-10317599-10318599-10319599-10320599-10321
599-10317S599-10318S599-10319S599-10320S599-10321S
599-10260599-10261
599-10364599-10365599-10366
599-10364S599-10365S599-10366S
1 1/2 in.
599-10218599-10219599-10220599-10221
599-10322599-10323599-10324599-10325599-10326
599-10322S599-10323S599-10324S599-10325S599-10326S
599-10262599-10263599-10264
599-10367599-10368599-10369
599-10367S599-10368S599-10369S
2 in.
599-10222599-10223599-10224599-10225
599-10327599-10328599-10329599-10330
599-10327S599-10328S599-10329S599-10330S
599-10265599-10266599-10267
599-10370599-10371599-10372
599-10370S599-10371S599-10372S
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin10
DimensionsFigure 2: M9000-700 linkage kit with VA9203 actuator
Figure 3: M9000-700 linkage kit with VA9208 actuator
3.500 (89)
8.277(210)
3.228 (82)
4.476 (114)
4.909 (125)
4.082 (104) 4.279
(109)For Belimo Valves
Clearance required
3.500 (89)
8.088
3.900 (99)
4.909 (125)
4.472 (114)
4.078 (104) 4.275
(109)For Belimo Valves
Clearance required
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin11
Figure 4: M9000-700 linkage kit with VA9104 actuator
Figure 5: M9000-700 linkage kit with VA9310 actuator
3.500 (89)
2.960 (75)
3.834 (97)4.267
(108)
3.440 (87)
3.637 (92)
5.368 (136)
For Belimo Valves
Clearance required
3.500 (89)
7.713 (196)
3.228 (82)
4.663 (118)
4.230 (107)
4.033 (102)
3.837 (97)
For Belimo Valves
Clearance required
Published in U.S.A. www.johnsoncontrols.com
M9000-700 Universal Ball Valve Linkage Kit Product Bulletin
12
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls.All other marks herein are the marks of their respective owners. © 2021 Johnson Controls.
Building Technologies & Solutions507 E. Michigan Street, Milwaukee, WI 53202
Figure 6: M9000-700 linkage kit with VA9310 actuator and M9300-xxx external switch or potentiometer kits
Technical specificationsM9000-700 universal ball valve linkage kitSuitable Johnson Controls actuators VA9203 Series spring return actuators
VA9208 Series spring return actuatorsVA9104 Series non-spring return actuatorsVA9310 Series non-spring return actuators
Suitable valves See relevant selection charts Minimum fluid temperature limits -22°F (-30°C)Maximum fluid temperature limits 284°F (140°C)Minimum ambient operating temperature -4°F (20°C)Maximum ambient operating temperature 140°F (60°C) 90% RH maximum, non-condensing
Minimum ambient storage temperature -40°F (-40°C)
Maximum ambient storage temperature 185°F (85°C) 95% RH maximum, non-condensing
Material Spacer: Glass-reinforced thermoplastic resinShaft: 12L15 steel zinc-platedConnector: 12L15 steel zinc-plated
Shipping weight 0.4 lbs (0.2kg)
3.500 (89)
4.297 (109)
8.428 (214)
4.413 (112)
4.609 (117)5.043
(128)
4.216 (107)
For Belimo Valves
Clearance required