Dimensions subject to change without notice. Certified prints are available upon request.
E4000
1
series E4000 “sealed for life” or regreaseable
The Link-Belt Series E4000 Idler line features factory lubricated and sealed for life rolls which elim-inate relubrication maintenance costs, thus lowering your total operating cost. Boasting load ratingswhich exceed CEMA E requirements, this rugged idler line is designed for maximum capacity andcontinuous handling of the heaviest, coarsest, most abrasive materials, such as coal, iron ore, copper,large stone and overburden.
Available in 36 to 96-inch belt width 20, 35, and 45 degree troughed, positive action training,impact, and return idlers, the unique design of the E4000S idler provides extended, trouble free ser-vice life for your belt conveyor equipment.
The E4000 rollers and frames are protected from corrosion by a polymeric powder coating (Corvel Gray) which is applied following a three-stage phos-phate cleaning operation. The finish is then baked on at high temperatures to provide resistance toabrasive elements. Assembly hardware is electro-zinc plated to ensure extended service.
The Series E4000 rollers, available in both 6 and 7-inch diameters, feature an exclusive, full lengthcenter tube and precision die-formed heads that are recessed into hot rolled mechanical shells. Theentire unit is then continuously welded robotically, thus ensuring an integral, airtight unit wherein contaminants and corrosion cannot enter. This unrivaled center tube design guarantees perfect shaft/bearing alignment. Bearing life is increased byusing solid, cold drawn steel shafts to minimize deflection and increase load ratings.
The redesigned premium quality Delrin triple horizontal labyrinth outer seal protects the precisiontapered roller bearings in several ways. The outer deflector cap (flinger) features a 90 degree con-toured lip to deflect material away from the roll end. Triple horizontal, greased-filled labyrinths andnitrile triple lip contact primary seals, along with rear non-contacting seals, ensure against the ingressof performance inhibiting contaminants. The outer adjusting nuts are zinc plated, machined steel, tominimize corrosion
The E4000 idler line features an inverted angle frame base with slotted footstraps to ensure quick,easy mounting and alignment. The heavy duty, die-formed, steel end brackets are contoured for generous clearance to safeguard against spilled materials becoming jammed and impeding the rotation of the rollers. All idler frames and rolls are welded in accordance with AWS D1.1 specifications for structural welds.
• Non contact rear lubrication seal
• Recessed die formed heads continuouslywelded inside shell ends
• Grease filled triple labyrinth Delrin seal with nitrile triple lip contact member
• Solid shaft minimizes deflection andincreases bearing life
• High capacity precision tapered rollerbearings for increased roll life with minimum roll resistance
• Machined steel adjusting nuts with improved molded deflector caps resist impact loadsand prevent ingress of contaminants into bearing cavity
• Rigid heavy gage center tube precisionbored for accurate bearing and seal alignment
• Heavy end retainer provides positive locking of roll shaft
• End brackets stamped withroll inclination, belt width and series
• Self-cleaning cross memberprevents material build-up
• Slotted footstraps simplifyinstallation and training adjustments
�sealed
for life�
The Link-Belt Series E4000 Idler line features factory lubricated rolls supplied with lubrication fittings at bothends of the idlers for ease in field regreasing from either side of the conveyor. The Series E4000 idler load ratingsexceed CEMA E requirements and are designed for high capacity, continuous material handling operations moving large volumes of the heaviest, coarsest, most abrasive materials,such as coal, iron ore, copper, large stone and overburden.
The complete line of E4000 Series idlers includes 36 to 96-inch belt width, 20, 35, and 45 degree 3 rolltroughed, positive action training, impact, and return idlers, as well as many specially designed products to suitevery material handling requirement.
The E4000 rollers and frames are protected from corrosion by a polymeric powder coating (Corvel Gray) which is applied following a three-stage phosphate clean-ing operation. The finish is then baked on at high temperatures to provide resistance to abrasive elements. Assembly hardware is electro-zinc plated to ensure extended service.
The Series E4000 rollers, available in both 6 and 7-inch diameters, feature an exclusive full length centertube and precision die-formed heads that are recessed into hot rolled mechanical shells. The entire unit is thencontinuously welded robotically, thus ensuring an integral, airtight unit in which contaminants and corrosion can-not enter.
The exclusive Delrin triple horizontal labyrinth outer seal protects the precision tapered roller bearings in sev-eral ways. The outer deflector cap (flinger) features a 90 degree contoured lip to deflect material away from the roll ends. Triple horizontal, grease filled labyrinths and nitrile triplelip contact primary seals ensure against the ingress of performance inhibiting contaminants. Additional protectionof the idler bearings is assured by the “grease filled center tube” and grease-through-lubrication. Each threeroll troughed idler is equipped with a standard grease fitting at each end, along with polypropylene shaft connec-tors between the center and end rolls for single point positivegreasing.
The information in this catalog section offers completeFMC Technologies Model Numbers, overall dimensions,and unit weight for the Link-Belt E4000 Series BeltConveyor Idler Line. For additional assistance in selecting the proper Link-Beltidlers please contact your FMC Technologies Customer Service Representative at1-800-356-4898.
2 Dimensions subject to change without notice. Certified prints are available upon request.
...handles the heaviest, most abrasive materials.
series E4000 regreaseable idlers
•Recessed die formed heads continuouslywelded inside shell ends
•Grease filled triple labyrinth Delrin seal with nitrile triple lip contact member
•Solid shaft minimizes deflection and increases bearing life
•High capacity precision tapered rollerbearings for increased roll life with minimum roll resistance
•Machined steel adjusting nuts withimproved molded deflector caps resistimpact loads and prevent ingress of contaminants into bearing cavity
•Grease filled center tube precisionbored for accurate bearing and seal alignment
Dimensions subject to change without notice. Certified prints are available upon request. 3
CAUTION: Link-Belt Conveyor idlers must be installed, operated and main-tained in accordance with accompanying FMC technologies ServiceInstructions. Failure to follow these instructions can result in serious person-al injury, property damage or both.
FMC Technologies Service Instructions accompany the shipment of equipment. If addi-tional copies of Service Instructions are required, they are available free of charge fromFMC Technologies, Material Handling Solutions Division, P.O. Box 1370, Tupelo, MS38802.
idlers of every type to meet your specific needs
CEMA classification
series no.
E4000
E4000
basic idlernomenclature
E4600
E4700
roll dia., in.
6
7
CEMA classold new
V E6
VI E7
idler interchangemanufacturer series no. manufacturer series no.
E4000SDX / SDX+E4000
FMC TechnologiesContinentalGoodman (Jeffrey)Hewitt-Robins
E6000 / E70006300-PE / E
RexnordStephens-AdamsonPrecisionPrecismeca (Transall)
series E4000
troughed belt idlerssteel rolls 20˚- 35˚- 45˚rubber cushion 20˚- 35˚- 45˚variable trough
troughed belt training idlerssteel rolls 20˚- 35˚
flat belt idlerssteel rollsrubber cushiontraining
return idlerssteel rollsrubber tread rollsbeaterv-return 5˚- 10˚
return training idlerssteel rollsrubber tread rolls
belt width, inches
36-9636-9636-96
36-72
36-9636-9636-72
36-9636-9636-9636-102
36-7236-72
CEMA Eroll dia., inches
6-76-76-7
6-7
6-76-76-7
6-76-76-76-7
6-76-7
!
L - live shaft typeR - rubber cushion or rubber tread rollsRC - rubber lagged impact center rollW - scale idler
S - “sealed for life”U - urethane coated or lagged rollersGAL - galvanized frame
One of the following letter suffixes may sometimes be necessary tocomplete an idler description:
4 Dimensions subject to change without notice. Certified prints are available upon request.
Variable troughed belt idlers placed between thefinal troughing idler and the head pulley, support thebelt during its transition from a concave to a flat con-tour. The end rolls can be adjusted vertically tomatch the changing contour of the belt during thiscritical period of transition. Standard design featuressteel rolls. Also available with all rubber cushion rollsor rubber cushion center roll and steel end rolls.
models: E4606S, E4706S, E4706RS, E4706RCS
Flat belt idlers are used for handling bulk materialssuch as prepared foundry sand and undelinted cottonseed where it is desirable to plow off material at oneor more intermediate points along the conveyor. Alsoused for pulpwood logs, packages, picking and sort-ing conveyors.
models: E4613S, E4713S
Troughed belt training idlers automatically train belts andprotect belt edges from damage caused by misalignment.Positive action type for belts operating in one direction; actuating shoe type for two directional operation (reversing).
models: E4607S, E4707S, E4608S, E4708SE4632S, E4732S, E4637S, E4737S
Troughed belt picking and feeder conveyor idlerscarry the load in a wide, thin layer where picking andsorting are required or where a shallow bed of material isrequired to minimize degradation. Standard design features rubber cushion center roll and steel end rolls.Also available with all steel or all rubber cushion rolls.
models: E4605S, E4705S, E4605RS, E4705RS, E4605RCS, E4705RCS
Flat belt training idlers automatically train belts and protect belt edges from damage caused by misalignment.Available in the positive action type for belts operating inone direction.
models: E4614S, E4714S
carrying idler types
Troughed belt idlers for general carrying serviceare available with roll inclinations of 20˚, 35˚, and 45˚.
models: E4601S, E4601W, E4701S, E4701W, E4602S, E4602W, E4702S, E4702W, E4628S, E4628W, E4728S, E4728W
Troughed belt rubber cushion idlers protect thebelt by absorbing impacts at loading and transferpoints. Design features include removable endbrackets on 35˚ and 45˚ idlers.
models: E4604S, E4704S, E4623S, E4723S, E4630S, E4730S
Flat belt rubber cushion idlers protect the belt byabsorbing impacts at loading and transfer points. Fixedshaft type is for average service.
models: E4615S, E4715S
Dimensions subject to change without notice. Certified prints are available upon request. 5
Return belt training idlers train the belt and protect itsedges from damage caused by misalignment. Positive actiontype for belts operating in one direction. Actuating shoe typefor reversing belts.
models: E4620S, E4720S, E4626S, E4726S
Return rubber tread training idlers train the belt and protectits edges from damage caused by misalignment. Used whenwet or sticky materials tend to cling to the belt, where corrosionresistance is required or where chemical attraction to iron orsteel is involved. Positive action type for belts operating in onedirection. Actuating shoe type for reversing belts.
models: E4621S, E4721S, E4627S, E4727S
Return belt beater idlers remove excessive amounts oftenacious materials that adhere to the belt.
models: E4619S, E4719S
Rigid frame v-return idlers provide a means of trainingthe return belt, with the added benefit of additional carry-ing load capacity. Rigid v-returns can be adjusted usingslotted bolt holes in the end brackets of the frame to aidin proper belt training.
models: E4664S, E4764S, E4665S, E4765S,E4666S, E4766S, E4668S, E4768S
return idler types
Return belt idlers carry the empty belt on thereturn run. Available with a urethane coating onstandard steel rollers.
models: E4617S, E4717S
Return belt rubber tread idlers are used whenwet or sticky materials tend to cling to the belt,where corrosion resistance is required or wherechemical reaction to iron or steel is involved.Available with urethane treads.
models: E4618S, E4718S
6 Dimensions subject to change without notice. Certified prints are available upon request.
20˚ troughed belt idlers equal length rolls
CEMA E”rolls
steel rolls
rubber cushion rolls (impact)
”rolls
”rolls
”rolls
*
*Demountable end bracket supplied for 36”- 96” belt widths
Dimensions subject to change without notice. Certified prints are available upon request. 7
20˚troughed belt training idlers equal length rolls
CEMA E positive action type(above deck mounting)
actuating shoe type(above deck mounting)
”rolls
”rolls
”rolls
”rolls
8 Dimensions subject to change without notice. Certified prints are available upon request.
35˚troughed belt idlers equal length rolls
CEMA Esteel rolls
rubber cushion rolls (impact)
”rolls
”rolls
”rolls
”rolls
*
*Demountable end bracket supplied for 36”- 96” belt widths
Dimensions subject to change without notice. Certified prints are available upon request. 9
35˚troughed belt training idlers equal length rolls
positive action type(above deck mounting)
CEMA E
actuating shoe type(above deck mounting)
”rolls
”rolls
”rolls
”rolls
10 Dimensions subject to change without notice. Certified prints are available upon request.
45˚troughed belt idlers equal length rolls
CEMA Esteel rolls
”rolls
”rolls
”rolls
”rolls
*
*Demountable end bracket supplied for 36”- 96” belt widths
rubber cushion rolls (impact)
Dimensions subject to change without notice. Certified prints are available upon request. 11
troughed belt picking & feeder conveyor idlers
steel rollsCEMA E
steel end rolls withrubber cushion center roll
”rolls
”rolls
”rolls
”rolls
20˚
12 Dimensions subject to change without notice. Certified prints are available upon request.
variable troughed belt idlers10 ̊- 35 ̊adjustment
■ 10" bolt spacing recommended to permit washer clearance and adjustment.● 1/4" thick steel rolls can be furnished.▼ 1/4" thick steel rolls standard for E-7" (series E4706S.)
Beltwidth
inchesIdler
number
Idlerweight,pounds
Standard base(Belt Width + 9")
Wide base(Belt width + 15")
CB F
GMIN. MAX.Inches
MIN. MAX.D
3642485460728496
232252276296319358449493
45.0051.0057.0063.0069.0081.0093.00
105.00
51.1957.1263.3169.4474.8886.4497.81
109.69
36.3841.7547.1252.5057.0667.3177.8188.38
43.4449.3855.3161.5666.6978.3889.81
101.69
11.8111.8111.8111.8111.8111.8112.5612.56
14.5614.9415.3715.6916.0616.7517.9418.62
19.9421.0622.3123.5024.5026.6229.5031.75
13.5615.5617.5619.6221.3825.2529.2533.25
E4706S-36E4706S-42E4706S-48E4706S-54E4706S-60E4706S-72E4706S-84E4706S-96
A Idlerweight,pounds
CA
InchesInches235255279300324363455499
45.0051.0057.0063.0069.0081.0093.00
105.00
51.1957.1263.3169.4474.8886.4497.81
109.69
Beltwidth
inchesIdler
number
Idlerweight,pounds
Standard base(Belt Width + 9")
Wide base(Belt width + 15")
CB F
GMIN. MAX.Inches
MIN. MAX.D
3642485460728496
202218237254277306394433
45.0051.0057.0063.0069.0081.0093.00
105.00
51.1957.1263.3169.4474.8886.4497.81
109.69
36.9442.3147.6953.1257.6267.8878.3888.94
43.6249.5655.6961.7567.0678.5690.00
101.88
11.3111.3111.3111.3111.3111.3112.0612.06
14.0614.4414.8115.1915.5616.2517.4418.12
19.5620.6921.9423.1224.0626.2529.0631.31
13.5615.5617.5619.6221.3825.2529.2533.25
E4606S-36E4606S-42E4606S-48E4606S-54E4606S-60E4606S-72E4606S-84E4606S-96
A Idlerweight,pounds
CA
InchesInches221242263283308344437481
45.0051.0057.0063.0069.0081.0093.00
105.00
51.1957.1263.3169.4474.8886.4497.81
109.69
●
CEMA E
steel rolls
”rolls
”rolls
Dimensions subject to change without notice. Certified prints are available upon request. 13
flat belt idlers
CEMA Erubber cushion rolls”rolls
”rolls
steel rolls
CEMA E”rolls
”rolls
14 Dimensions subject to change without notice. Certified prints are available upon request.
flat belt training idlers
CEMA Epositive action type
”rolls
”rolls
”rolls
”rolls
return belt beater idlers
Dimensions subject to change without notice. Certified prints are available upon request. 15
return belt idlers
steel rollsCEMA E”rolls
”rolls
rubber tread rollsmassed ends”rolls
”rolls
16 Dimensions subject to change without notice. Certified prints are available upon request.
return belt training idlers
CEMA Esteel rollspositive action type
rubber tread rolls positive action typemassed ends
”rolls
”rolls
”rolls
”rolls
Dimensions subject to change without notice. Certified prints are available upon request. 17
return belt training idlers
steel rollsactuating shoe type
CEMA E”rolls
”rolls
rubber tread rolls actuating shoe typemassed ends”rolls
”rolls
18 Dimensions subject to change without notice. Certified prints are available upon request.
v-return idlers
Belt�width,�inches
**Idler�
number
Idler�weight,�pounds
A B C F G H K
Belt�width,�inches
**Idler�
number
Idler�weight,�pounds
A B C F H KG
■ 10" bolt spacing recommended to permit adjustment.�● 1/4" thick steel rolls can be furnished.�** For belt width + 15" mounting, use next higher belt width.�▼ 1/4" thick steel rolls standard for E-7" (series E4764S.)��
36�42�48�54�60�66�72�78�84�90�96�102
E4664S-36�E4664S-42�E4664S-48�E4664S-54�E4664S-60�E4664S-66�E4664S-72�E4664S-78�E4664S-84�E4664S-90�E4664S-96�E4664S-102
36�42�48�54�60�66�72�78�84�90�96�102
E4764S-36�E4764S-42�E4764S-48�E4764S-54�E4764S-60�E4764S-66�E4764S-72�E4764S-78�E4764S-84�E4764S-90�E4764S-96�E4764S-102
134�152�166�191�203�218�236�251�267�281�296�330
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
41.19�47.12�53.00�60.38�64.94�70.94�76.94�82.88�89.50�95.44�101.44�107.44
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
15.19�15.81�16.06�16.38�16.62�16.88�17.81�18.06�18.31�18.62�18.88�19.12
19.62�22.62�25.56�29.25�31.56�34.56�37.56�40.56�43.88�46.88�49.88�52.88
4.56�4.81�5.12�5.38�5.62�5.88�6.12�6.44�6.69�6.94�7.19�7.44
.50�
.56�
.56�
.56�
.56�
.56�
.62�
.62�
.62�
.62�
.62�
.62��
Inches
Inches134�152�166�191�203�218�236�251�267�281�296�330
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
41.06�47.06�52.88�60.25�64.88�70.88�76.81�82.81�89.44�95.38�101.38�107.31
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
15.19�15.81�16.06�16.38�16.62�16.88�17.81�18.06�18.31�18.62�18.88�19.12
19.62�22.62�25.56�29.25�31.56�34.56�37.56�40.56�43.88�46.88�49.88�52.88
4.06�4.31�4.62�4.88�5.12�5.38�5.62�5.94�6.19�6.44�6.69�6.94
.50�
.56�
.56�
.56�
.56�
.56�
.62�
.62�
.62�
.62�
.62�
.62��
Belt�width,�inches
**Idler�
number
Idler�weight,�pounds
A B C F G H K
Belt�width,�inches
**Idler�
number
Idler�weight,�pounds
A B C F H KG
■ 10" bolt spacing recommended to permit adjustment.�● 1/4" thick steel rolls can be furnished.�** For belt width + 15" mounting, use next higher belt width.�▼ 1/4" thick steel rolls standard for E-7" (series E4765S.)��
36�42�48�54�60�66�72�78�84�90�96�102
E4665S-36�E4665S-42�E4665S-48�E4665S-54�E4665S-60�E4665S-66�E4665S-72�E4665S-78�E4665S-84�E4665S-90�E4665S-96�E4665S-102
36�42�48�54�60�66�72�78�84�90�96�102
E4765S-36�E4765S-42�E4765S-48�E4765S-54�E4765S-60�E4765S-66�E4765S-72�E4765S-78�E4765S-84�E4765S-90�E4765S-96�E4765S-102
135�153�166�192�204�219�237�252�268�283�298�332
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
40.25�46.12�51.94�59.19�63.75�69.69�75.56�81.50�88.00�93.94�99.88�105.75
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
17.31�18.19�18.69�19.25�19.75�20.31�21.50�22.06�22.56�23.12�23.62�24.19
19.62�22.62�25.56�29.25�31.56�34.56�37.56�40.56�43.88�46.88�49.88�52.88
6.62�7.12�7.69�8.19�8.75�9.25�9.81�10.31�10.88�11.38�11.88�12.44
.75�
.81�
.81�
.81�
.81�
.81�
.94�
.94�
.94�
.94�
.94�
.94��
Inches
Inches162�184�201�231�246�264�287�306�326�345�364�402
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
40.06�46.00�51.75�59.00�63.56�69.50�75.44�81.31�87.88�93.75�99.69�105.56
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
19.62�22.62�25.56�29.25�31.56�34.56�37.56�40.56�43.88�46.88�49.88�52.88
6.12�6.62�7.19�7.69�8.25�8.75�9.31�9.81�10.31�10.88�11.38�11.94
.75�
.81�
.81�
.81�
.81�
.81�
.94�
.94�
.94�
.94�
.94�
.94��
17.31�18.19�18.69�19.25�19.75�20.31�21.50�22.06�22.56�23.12�23.62�24.19
CEMA E” rolls
” rolls
” rolls
” rolls
10˚
5˚steel rolls v-return
steel rolls v-return
Dimensions subject to change without notice. Certified prints are available upon request. 19
v-return idlers
Belt�width,�inches
**Idler�
number
Idler�weight,�pounds
A B C F G H K
Belt�width,�inches
**Idler�
number
Idler�weight,�pounds
A B C F H KG
■ 10" bolt spacing recommended to permit adjustment.�● 1/4" thick steel rolls can be furnished.�** For belt width + 15" mounting, use next higher belt width.�▼ 1/4" thick steel rolls standard for E-7" (series E4766S.)��
36�42�48�54�60�66�72�78�84�90�96�102
E4666S-36�E4666S-42�E4666S-48�E4666S-54�E4666S-60�E4666S-66�E4666S-72�E4666S-78�E4666S-84�E4666S-90�E4666S-96�E4666S-102
36�42�48�54�60�66�72�78�84�90�96�102
E4766S-36�E4766S-42�E4766S-48�E4766S-54�E4766S-60�E4766S-66�E4766S-72�E4766S-78�E4766S-84�E4766S-90�E4766S-96�E4766S-102
135�154�167�193�205�220�239�254�270�285�300�335
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
39.00�44.75�50.44�57.56�62.06�67.88�73.69�79.44�85.81�91.62�97.44�103.25�
�
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
19.50�20.69�21.50�22.31�23.12�23.88�25.38�26.19�27.00�27.81�28.62�29.44
19.62�22.62�25.56�29.25�31.56�34.56�37.56�40.56�43.88�46.88�49.88�52.88
8.62�9.44�10.25�11.06�11.88�12.69�13.50�14.31�15.12�15.88�16.69�17.50
.94�1.06�1.06�1.06�1.06�1.06�1.25�1.25�1.25�1.25�1.25�1.25�
�
Inches
Inches162�185�202�232�248�266�289�308�328�347�366�405
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
38.75�44.50�50.19�57.31�61.81�67.56�73.38�79.19�85.56�91.38�97.19�103.00
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
19.62�22.62�25.56�29.25�31.56�34.56�37.56�40.56�43.88�46.88�49.88�52.88
8.12�8.94�9.75�10.56�11.38�12.19�13.00�13.75�14.56�15.38�16.19�17.00
19.50�20.69�21.50�22.31�23.12�23.88�25.38�26.19�27.00�27.81�28.62�29.44
.94�1.06�1.06�1.06�1.06�1.06�1.25�1.25�1.25�1.25�1.25�1.25�
�
CEMA E
Belt�width,�inches
** Idler�number
Idler�weight,�pounds
A B C F G H K
Belt�width,�inches
** Idler�number
Idler�weight,�pounds
A B C F H KG
■ 10" bolt spacing recommended to permit adjustment.�** For belt width + 15" mounting, use next higher belt width.���
36�42�48�54�60�66�72�78�84�90�96�102
E4668S-36�E4668S-42�E4668S-48�E4668S-54�E4668S-60�E4668S-66�E4668S-72�E4668S-78�E4668S-84�E4668S-90�E4668S-96�E4668S-102
36�42�48�54�60�66�72�78�84�90�96�102
E4768S-36�E4768S-42�E4768S-48�E4768S-54�E4768S-60�E4768S-66�E4768S-72�E4768S-78�E4768S-84�E4768S-90�E4768S-96�E4768S-102
124�144�154�180�189�199�219�230�241�258�268�299
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
38.38�44.25�50.06�57.38�61.94�67.81�73.75�79.62�86.19 �92. 06�98.00�103.88�
�
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
17.31�18.19�18.69�19.25�19.75�20.31�21.50�22.06�22.56�23.12�23.62�24.19
19.44�22.44�25.38�29.06�31.38�34.38�37.38�40.38�43.69�46.69�49.69�52.69
6.62�7.12�7.69�8.19�8.75�9.25�9.81�10.31�10.88�11.38�11.88�12.44
.75�
.81�
.81�
.81�
.81�
.81�
.94�
.94�
.94�
.94�
.94�
.94��
Inches
Inches136�159�169�198�207�217�241�251�263�283�293�323
48.12�54.12�60.12�66.12�72.12�78.12�84.12�90.12�96.12�102.12�108.12�114.12
38.19�44.06�49.88�57.19�61.75�67.69�73.56�79.50�86.00�91.88�97.81�103.69
45.00�51.00�57.00�63.00�69.00�75.00�81.00�87.00�93.00�99.00�105.00�111.00
6.12�6.62�7.19�7.69�8.25�8.75�9.31�9.81�10.31�10.88�11.38�11.94
.75�
.81�
.81�
.81�
.81�
.81�
.94�
.94�
.94�
.94�
.94�
.94��
17.31�18.19�18.69�19.25�19.75�20.31�21.50�22.06�22.56�23.12�23.62�24.19
19.44�22.44�25.38�29.06�31.38�34.38�37.38�40.38�43.69�46.69�49.69�52.69
” rolls
” rolls
” rolls
” rolls
10˚
15˚steel rolls v-return
rubber tread rolls v-returnmassed ends
• Heavy end retainer provides positive locking of roll shaft
• Slotted footstraps simplify installation and training adjustments
• Self-cleaning cross memberprevents material build-up
• End brackets stampedwith roll inclination, beltwidth and series
20 Dimensions subject to change without notice. Certified prints are available upon request.
E4000H
Dseries E4000HD “sealed for life”
or regreaseable for increased capacity.
Series E4000HD Heavy-Duty idler assemblies are recommendedwhere loads exceed CEMA E ratings. The heavy duty design which uses astep shaft design with standard 1 1/4-inch bearings will, in many cases,permit the conveying of loads up to 50 percent greater than the normalcapacities. Available in 6 and 7-inch diameter rolls, the carrying idler’sexternal dimensions are identical to Series E4000. All Series E4000HDHeavy Duty Idlers are available for belt widths up to 72-inch. Troughedidlers for 20, 35 and 45-inch trough angles are available for belt widthsthrough 96-inch.
Dimensional information is available on request for Series E4000HDHeavy Duty Idlers not shown in this catalog.
• Grease filled combination triple labyrinthDelrin seal with felt contact member
• Non contact rearlubrication seal
• Recessed dieformed heads continuously welded inside shell ends
• Oversized solidshaft minimizes deflection andincreases bearing life
• Rigid heavy gage center tubeprecision bored for accuratebearing and seal alignment
• Machined steel adjusting nuts withimproved molded deflector capsresist impact loads and preventingress of contaminants intobearing cavity
• High capacity precisiontapered roller bearings for increased roll life withminimum roll resistance
�sealed for life�