Download pdf - Installing v-Ribbed Belt

7/28/2019 Installing v-Ribbed Belt

http://slidepdf.com/reader/full/installing-v-ribbed-belt 1/3

FABIA 2000➤ 1.2/40; 1.2/47 Engine, Mechanical Components

Removing and installing V-ribbed beltEdition 08.02

S00.5322.00.2013-1 page 1

13

13-1 Removing and installing V-ribbed belt

Summary of components

♦ Mark the rotation direction before removing the V-ribbed belt. Reversing the rotation direction of an already used belt may destroy it.

♦ Pay attention to the correct position of the V-ribbed belt in the belt pulley when installing it.

♦ Vehicles without an air-conditioning system do not have an air-conditioning compressor or guide pulley.

1 - 22 Nm

2 - Belt pulley

❑ on the coolant pump

3 - Trim4 - Tensioner with tensioning

pulley

❑ do not remove the tensioningpulley.

5 - 40 Nm

6 - Generator

❑ to facilitate positioning of thegenerator on the cylinderblock, drive the threadedbushings of the screwsslightly backwards

7 - Guide pulley8 - Washer

❑ Camber towards the outside

9 - Belt pulley

❑ for crankshaft

10 - 90 Nm + torque a further 90 (1 / 4 turn)

❑ replace

❑ interlock the crankshaft witha drift -T10121- for looseningand tightening it up

⇒ Chapter 13-311 - Distance sleeve

❑ for generator

12 - 23 Nm

13 - Distance sleeve

❑ for the AC compressor

14 - Dowel sleeves for AC compressor

❑ must be inserted in the cylinder block

15 - V-ribbed belt

❑ Routing of the V-ribbed belt

vehicles without air conditioning⇒ Fig. 1 in 13-1 page 2

Vehicles with air conditioning⇒ Fig. 2 in 13-1 page 3❑ removing and installing⇒ 13-1 page 2

13 – Crankgear

Note




Removing and installing V-ribbed belt Edition 08.02

S00.5322.00.2013-1 page 2

13

Removing

– Mark the rotation direction of the V-ribbed belt.

– Lever off the cover for the tensioning roller -A-.

– Swing out the tensioning roller -A- with Torx key 50 -B-

in the direction of travel up to the stop and remove theV-ribbed belt.

The tensioning roller can be interlocked by inserting a rig pin.

Installing

♦ Inspect V-ribbed belt ⇒ Inspection and Maintenance.

♦ Before fitting the V-ribbed belt make sure that all as- semblies (generator, coolant pump and AC compressor) are securely mounted.

♦ Check smooth operation of belt pulley, tensioning and guide pulley.

♦ Pay attention to the rotation direction of already used V-ribbed belts.

– Position the V-ribbed belt on the belt pulleys and

guide pulley.

– Swing out the tensioning roller -A- with Torx key 50 -B-

in the direction of travel up to the stop and lay the V-ribbed belt in place.

– Press on the cover of the tensioning roller -A-.

– Start engine and check belt run.

Fig. 1: V-ribbed belt run - without an air condition-ing system

1 - Belt pulley - crankshaft

2 - Belt pulley - coolant pump

3 - Tensioning pulley

4 - Belt pulley - generator

Note

Note




Removing and installing V-ribbed beltEdition 08.02

S00.5322.00.2013-1 page 3

13

Fig. 2: V-ribbed belt run - with an air conditioningsystem

1 - Belt pulley - crankshaft

2 - Belt pulley - coolant pump

3 - Tensioning pulley

4 - Belt pulley - generator

5 - Belt pulley - AC compressor

6 - Guide pulley