isd dunaferr Product catalogue
HOT ROLLED PRODUCTS
Hot rolled strips are produced on a semi-continuous rolling mill. It consists of a duo reversing vertical and horizontal roughing stand and a six-stand quarto mill.
SLAB TYPESSlab type
B 08 B 09 B 10 B 11 B 12 B 13 B 14 B 15Width; b (mm) 860 940 1 045 1 120 1 220 1 305 1 420 1 550
Specific weight (t/m) * 1.510 1.656 1.860 2.000 2.178 2.341 2.585 2.820
* depend on grade and thickness
Slab thickness: 230 mm
1. MAIN PARAMETERS
Coil Sheet
Thickness; h (mm) 1.218.0 1.212.5
Width; b (mm) 8001 540 8001 540 with mill edge 8001 500 with trimmed edge
Length; l (mm) 1 7508 000 up to the thickness of max 8 mm 1 75012 000 above the thickness of 8 mm
Edge trimming applied within the thickness range of 2.08.0 mm for plain sheets in
strength grades IV. and for sheets with pattern in strength grades IIV.
1.1. COIL WEIGHTS AND DIMENSIONS
Width; b (mm) 800860 861940 9411 045 1 0461 120 1 1211 220 1 2211 305 1 3061 420 1 4211 540
Weight (t)46 46.5 57.5 5.58 69 6.59.5 710.5 811.5
1012.5 1113.5 12.515.5 13.516.5 14.518 15.519.5 17.521 1923
Coil outside diameter: max. 1 950 mmCoil inside diameter: 750 50 mm
1.2. SHEET DIMENSIONS
Commercial sheet dimensions
Width; b (mm)Length; l (mm)
2 000 2 500 3 000 6 000
1 000h = 1.5; 2; 2.5; 3; 4; 5; 6; 8; 10; 12 mm
1 250 h = 2; 2.5; 3; 4;
5; 6; 8; 10; 12 mm
1 500 h = 2.5; 3; 4;
5; 6; 8; 10; 12 mmh = 2.5; 3; 4;
5; 6; 8; 10; 12 mm
DASZ-Dunaferr Steel Standard
2 DASZ-Dunaferr Steel Standard
2. PRODUCT GROUPS
The latest issued standard are applied for our products. The mechanical properties and chemical compositions in the tables are valid taking into account the supplementary specifications of the indicated standards.
Definition of strength grades:According to EN 10051:
Grade A with minimum yield strength Re 300 MPaGrade B with minimum yield strength 300 MPa < Re 360 MPaGrade C with minimum yield strength 360 MPa < Re 420 MPaGrade D with minimum yield strength 420 MPa < Re 900 MPa
ISD Dunaferr Co. Ltd. applies DASZ 03 instead of EN 10051:I. Steel grades characterised with maximum yield strength, used for cold rolling,II. Steel grades with minimum 185 MPa yield strength,III. Steel grades with minimum 235 MPa yield strength,IV. Steel grades with minimum 275 MPa yield strength,V. Steel grades with minimum 340 MPa yield strength,VI. Steel grades with minimum 420 MPa yield strength,VII. Steel grades with minimum 460 MPa yield strength,VIII. Steel grades with minimum 500 MPa yield strength.
DASZ 03 standard includes the producible dimension ranges as well as dimensional tolerances by strength grades. These tolerances are either the same as or stricter than that specified by EN 10051 standard.
Tolerances of hot rolled products according to DASZ 03 standard are chapter 5.In case of standards with the same number, but from different years the specifications of the standard included in the delivery contract are normative.
2.1. HOT ROLLED MILD STEEL STRIPS
2.1.1. Steels for cold rolling
Typical applications: re-rolling, pressing base material, small and medium scale deep-drawing and production of parts suitable for special deep-drawing and complex machining.
Strength grade DIN 1614JIS G 3131
ASTM A568 SAE
I.
St 22 SPHC 1010
RR St 23 SPHD 1008
St 24 SPHE 1006
Steels with increased yield strength for cold rolling are included in chapter 2.6.3.
2.1.2. STEELS fOR ENAMELLING
Typical applications: boilers, ovens, gas convectors and other household appliances.
Strength grade DIN 1623DASZ 206
I.
EK 2
EK 4
FeP13-B
3DASZ-Dunaferr Steel Standard
2.1.3. STEELS fOR COLD fORMING
Typical applications: depending on the steel grade these steels are applied for parts made by small, medium and large scale deep-drawing, such as compressors and for bent, cold formed products.
Strength grade EN 10111DIN
1614
I.
DD11 StW 22
DD12 RR StW 23
DD13 StW 24
DD14
2.2. UNALLOYED HOT ROLLED CONSTRUCTIONAL STEELS
Typical applications: construction, production of welded structures, pressed parts, bent sections and tubes.
Strength grade EN 10025-2DIN
17100
II. S185 St 33
III.
St 37-2
USt 37-2
S235JR RSt 37-2
S235J0 St 37-3-U
St 37-3 N
IV.
S275JR St 44-2
S275J0 St 44-3 U
St 44-3 N
S275J2
V.
S355JR
S355J0 St 52-3 U
St 52-3 N
S355J2
VI. E295 St 50-2
VII. E335 St 60-2
VIII. E360 St 70-2
The products are delivered in normalised or rolled condition. If the product is ordered with normalising rolling the +N marking shall be added to the grade specification.
Symbols of the impact test specificationV-notch on 1010 mm specimen
Test temperature (C)27 J 40 J 60 JJR KR LR 20
J0 K0 L0 0
J2 K2 L2 -20
J3 K3 L3 -30
J4 K4 L4 -40
J5 K5 L5 -50
J6 K6 L6 -60
2.3. STEELS RESISTANT TO ATMOSPHERIC CORROSION
Typical applications: support and cover elements of outdoor surfaces exposed to weather conditions and production of containers suitable for sea transport.
Steels resistant to atmospheric corrosion can be used profitably as structural steels, because there is no need for additional surface protection. The continuous brown surface layer that develops in one year slows down further corrosion of the steel. The qualities produced according to DASZ 210 standard are phosphor alloyed and atmospheric corrosion resistant steel grades that have been developed based on quality CORTEN A.
4 DASZ-Dunaferr Steel Standard
Strength grade EN 10025-5DASZ 210
III.S235J0W
S235J2W
IV. D-COR-TEN 410
V.S355J0W D-COR-TEN 510
S355J2W
2.4. STEELS fOR MANUfACTURING Of BOILERS AND PRESSURE VESSELS
Typical applications: boilers, pressure vessels, gas bottles, boilers and containers.
The characteristics of these steel types are excellent formability, weldability and low content of impurities.
Strength grade EN 10028-2EN
10028-3EN
10207DIN
17155NF
A36-205EN
10120
III.
A 37 CP
P235GH H I A 37 AP P245NB
P235S A 37 FP
IV.
A 42 CP
P265 GH H II A 42 AP P265NB
P265S A 42 FP
P275N
P275NH
P275NL1 P275SL
P275NL2
A 48 CP
P295GH 17 Mn 4 A 48 AP P310NB
A 48 FP
V.
A 52 CP
P355GH 19 Mn 6 A 52 AP
P355N A 52 FP P355NB
P355NH
P355NL1
P355NL2 -
Letters:GH, H for high temperature service, with hot yield point testL for low temperature serviceB base material of gas bottlesP base material of pressure vessels and boiler platesS cold toughness, applicable also at low temperatureSL cold toughness, with specification of impact test value at -50CN produced by normalising rolling
2.5. TUBE MATERIALS
Typical applications: spirally and longitudinal welded tubes with different diameters.
The characteristics of these steel types are weldability, toughness and low content of impurities.
Strength grade EN 10208-2DIN
17100DIN
17172API
SPEC 5L
II. Gr A
III. RRoSt 37-2
RoSt 37-3
IV.
L245NB, MB RoSt 44-2 StE 290.7 TM Gr B
L290NB, MB RoSt 44-3 StE 320.7 TM X 42
X 46
V.L360NB, MB RoSt 52-3 StE 360.7 TM X 52
X 56
VI. L415NB, MB StE 415.7 TM X 60
VII.L450NB, MB StE 445.7 TM X 65
L485NB, MB StE 480.7 TM X 70
Letters according to EN 10208-2 standard:L base material of tube N by normalising rollingM by thermo-mechanical rolling B B-class tubes
5DASZ-Dunaferr Steel Standard
2.6. fINE-GRAINED STEELS
Typical applications: welded structures, bridges, containers and water tanks exposed to high load at low ambient temperature.Hot rolled steels with high strength, with extremely good weldability and formability properties. Specifically developed combination of high strength properties and good formability.
2.6.1. fine-grained steels produced by normalising rolling
Strength grade EN 10025-3EN
10149-3SEW 092
IV.S275N, NL S260NC QStE 260 N
S315NC
V.S355N, NL S355NC QStE 340 N
QStE 380 N
VI. S420N, NL S420NC QStE 420 N
VII. S460N, NL S460NC QStE 460 N
Letters according to EN 10025-3 standard:N by normalising rollingNL by normalising rolling, impact test at -50 C
2.6.2. fine-grained steels produced by thermo-mechanical rolling
Strength grade EN 10149-2EN
10025-4SEW 092
IV. S315MC S275M, ML
V.S355MC S355M, ML QStE 340 TM
QStE 380 TM
VI. S420MC S420M, ML QStE 420 TM
VII. S460MC S460M, ML QStE 460 TM
VIII.S500MC QStE 500 TM
S550MC QStE 550 TM
Letters according to EN 10149-2 standard:M by thermo-mechanical rollingC suitable for edge bending
2.6.3. fine-grained steels for cold rolling
Strength grade SEW 093
IV.ZStE 260
ZStE 300
V.ZStE 340
ZStE 380
VI. ZStE 420
2.7. TEMPERING, CASE HARDENING AND SPRING STEELS
Typical applications: machine parts as tempered steels or austempered steels.Delivery condition: hot rolled
Strength grade EN 10083-1
V.
2 C 22
2 C 25
2 C 35
2 C 40 *
2 C 45 *
2 C 50 *
VI.
2 C 55 *
2 C 60 *
28 Mn 6 *
25 CrMo 4 *
34 CrMo 4 *
51 CrV 4 *
* based on technical agreement.
6 DASZ-Dunaferr Steel Standard
2.8. WEAR RESISTANT STEELS
Typical applications: primarily for production of parts exposed to wear and tear, plough iron, breast board and sliding bases.
Wear resistance and toughness of different parts produced by boron micro-alloyed, fine-grained hot rolled products are adjustable by annealing, hardening and in case of need subsequent tempering performed at the end-user. Orders may only based on technical agreement.
Strength grade DASZ 200
VII.
DHR 42
DHR 48
DHR 50
DHR 52
2.9. ELECTROTECHNICAL STEELS
Typical applications: electric industrial applications, production of isotropic, cold rolled products with non-grain-oriented structure.
Strength grade DASZ 215
III.
DN 1,0 Si
DN 1,2 Si
DN 1,5 Si
DN 1,8 Si
DN 2,0 Si *
DN 2,1 Si *
DN 2,5 Si *
DN 3,0 Si *
* based on a technical agreement.
3. SPECIAL PRODUCTS
3.1. HOT ROLLED COILS AND SHEETS fOR PLASMA AND LASER CUTTING
The requirements of suitability for laser cutting are summarised in DASZ 216 standard. These products are ultra high-purity steels with low inclusion content, produced according to reduced chemical composition limit values, with reduced S-, P- and Si-contents; fine-grained, micro-alloyed, with more reduced mechanical values than those specified by similar standards and low internal stress, suitable for edge bending, as well as for plasma and laser cutting. Steel grades, specified by DASZ 216 standard or any other national or international standards, suitable for plasma and laser cutting, can be ordered.
FlatnessIn case of ordering plain sheets the flatness tolerances, depending on the strength grades according to EN 10051 standard, are given in the following table. Definition of the strength grades (A, B, C, D) according to EN 10051 standard are included in chapter 2 of this catalogue.
Flatness tolerance max. (mm/m)A B C D
4 4 5 5
Patterned sheets flatness tolerance (mm/m)
Width; b (mm)Thickness; h (mm)
1.601.99 2.002.30 2.312.99 3.0012.008001 300 10 8 8 8
1 3011 540 8
In case of ordering coils suitable for laser cutting our company guarantee the flatness tolerances in the above table for cut-to-length sheets only after performance of a professional levelling process on a cutting line with suitable technical conditions.
7DASZ-Dunaferr Steel Standard
3.2. HOT ROLLED PRODUCTS fOR GALVANIzING
Suitability for hot-dip galvanizing according to EN 10025 standard is specified in the following table.
ClassElements in mass percent
Si Si + 2.5 P P1 Si 0.030 0.090
2* Si 0.35
3 0.14 Si 0.25 0.035
* Class 2 refers only to special zinc-alloys.
3.3. PATTERNED COILS AND SHEETS (DASz 141)
Typical applications: construction industrial stairs, paths, pavements and warehouse areas.
Patterned products can be ordered in steel grades with strength grades I-V according to DASZ 03 standard.
Pattern types
Diamond pattern Teardrop pattern
8 DASZ-Dunaferr Steel Standard
Dense teardrop pattern Wide teardrop pattern
Pattern parameters of coils and sheetsPattern
Diamond Teardrop Dense teardrop Wide teardropTop width (mm)) 2.814.20 3.907.10 4.908.45 3.847.22
Bottom width (mm) 4.204.90 6.308.30 8.2010.10 8.009.30
Length (mm) 27.3033.60 24.3029.30 30.0032.00
Pattern height:Thickness; h (mm) Minimal pattern height (mm) Maximal pattern height (mm)
1.602.30 0.60
2.002.313.00 0.80
3.019.99 1.00
10.0016.50* 0.80
* above 12 mm thickness it can only be ordered in coils
4. SURfACE
Our products are delivered according to EN 10163-2 standard class B sub-class 3.
9DASZ-Dunaferr Steel Standard
5. TOLERANCES (DASz 03)
The specified values for tolerances shall not apply to the uncropped ends of the coil for a total length l, whichis calculated using the formula:
90l (m)= 20 m nominal thicknes (mm)
5.1. THICKNESS TOLERANCES
5.1.1. Thickness tolerances of plain products
Strength grade I., normal thickness tolerances
Thickness; h (mm)
Width; b (mm)
b < 980 980 b 1040 1040 < b 1120 1120 < b 1200 1200 < b 1220 1220 < b 1300 1300 < b 1500 b > 1500
1.201.29 0.13
1.301.49 0.13
1.501.79 0.13 0.14
1.802.00 0.13 0.14
2.012.49 0.14 0.16
2.50 0.14 0.16 0.17
2.513.00 0.15 0.17 0.18
3.014.00 0.17 0.18 0.20
4.015.00 0.18 0.20 0.21
5.016.00 0.20 0.21 0.22
6.018.00 0.22 0.23 0.23
8.0110.00 0.32 0.33 0.34
10.0112.50 0.35 0.36 0.37
12.5115.00 0.37 0.38 0.40
15.0118.00 0.40 0.42 0.45
Strength grade I., reduced thickness tolerances
Thickness; h (mm)
Width; b (mm)
b < 980 980 b 1040 1040 < b 1120 1120 < b 1200 1200 < b 1220 1220 < b 1300 1300 < b 1500 b > 1500
1.201.29 0.07
1.301.49 0.07
1.501.79 0.07
1.802.49 0.08
2.503.00 0.08
3.015.00 0.09
5.016.00 0.09 0.10
6.018.00 0.10 0.11
8.0110.00 0.16 0.17 0.17
10.0112.50 0.18 0.18 0.19
12.5115.00 0.19 0.19 0.20
15.0118.00 0.20 0.21
10 DASZ-Dunaferr Steel Standard
Strength grade II-III., normal thickness tolerances
Thickness; h (mm)
Width; b (mm)
b < 980 980 b 1040 1040 < b 1120 1120 < b 1200 1200 < b 1220 1220 < b 1300 1300 < b 1500 b > 15001.201.29 0.17
1.301.49 0.17
1.501.79 0.17 0.19
1.802.00 0.17 0.19
2.012.49 0.18 0.21
2.50 0.18 0.21 0.23
2.513.00 0.20 0.22 0.24
3.014.00 0.22 0.24 0.26
4.015.00 0.24 0.26 0.28
5.016.00 0.26 0.28 0.29
6.018.00 0.29 0.30 0.31
8.0110.00 0.32 0.33 0.34
10.0112.50 0.35 0.36 0.37
12.5115.00 0.37 0.38 0.40
15.0118.00 0.40 0.42 0.45
Strength grade II-III., reduced thickness tolerances
Thickness; h (mm)
Width; b (mm)
b < 980 980 < b 1040 1040 < b 1120 1120 < b 1200 1200 < b 1220 1220 < b 1300 1300 < b 1500 b > 15001.201.29 0.07
1.301.49 0.07
1.501.79 0.07
1.802.49 0.08
2.503.00 0.08
3.014.00 0.09
4.015.00 0.10
5.016.00 0.11 0.12
6.018.00 0.15 0.16
8.0110.00 0.16 0.17 0.17
10.0112.50 0.18 0.18 0.19
12.5115.00 0.19 0.19 0.20
15.0118.00 0.20 0.21
Strength grade IV., normal thickness tolerances
Thickness; h (mm)
Width; b (mm)
b 1120 1120 < b 1200 1200 < b 1250 1250 < b 1300 1300 < b 1500 b > 15001.501.89 0.17
1.901.99 0.17 0.19
2.00 0.17 0.19
2.012.50 0.18 0.21
2.512.79 0.20 0.22
2.803.00 0.20 0.22 0.24
3.014.00 0.22 0.24 0.26
4.015.00 0.24 0.26 0.28
5.016.00 0.26 0.28 0.29
6.018.00 0.29 0.30 0.31
8.0110.00 0.32 0.33 0.34
10.0112.50 0.35 0.36 0.37
12.5115.00 0.37 0.38 0.40
15.0118.00 0.40 0.42 0.45
11DASZ-Dunaferr Steel Standard
Strength grade IV., reduced thickness tolerances
Thickness; h (mm)
Width; b (mm)
b 1 120 1 120 < b 1 200 1 200 < b 1 250 1 250 < b 1 300 1 300 < b 1 500 b > 1 5001.50-1.89 0.08
1.90-1.99 0.08
2.00-2.79 0.09
2.80-4.00 0.09
4.01-5.00 0.10
5.01-6.00 0.11 0.12
6.01-8.00 0.15 0.16
8.01-10.00 0.16 0.17
10.01-12.50 0.18 0.19
12.51-15.00 0.19 0.20
15.01-18.00 0.20 0.21
Normal thickness tolerances of our products of the strength grade V. and above are specified according to DASZ 03 standard being equal to or stricter than the values specified by EN 10051 standard.
Our products of the strength grade V. and above can also be ordered with reduced tolerances, if agreed.
5.1.2. Thickness tolerances of patterned products
Thickness*; h (mm)
Width; b (mm)b 1040 1040 < b 1300 1300 < b 1540
1.601.79 0.17
1.801.99 0.20 0.20
2.002.29 0.20 0.20
2.302.50 0.20 0.28
2.512.99 0.20 0.28
3.004.00 0.28 0.29 0.29
4.014.99 0.28 0.30 0.30
5.005.99 0.30 0.33 0.33
6.006.99 0.33 0.35 0.35
7.008.50 0.36 0.38 0.38
8.5110.00 0.40 0.41 0.41
10.0116.5 0.44 0.44 0.44
* The thickness (h) is the dimension of the part of the material without patterns.
5.2. WIDTH TOLERANCES
Width tolerances of coils and sheets mill edges:Width; b (mm) Width tolerance (mm)
b 1 200 - 0 / + 20
1 200 < b 1 500 - 0 / + 20
1 500 < b - 0 / + 25
Width tolerances trimmed edges:Width; b (mm) Width tolerance (mm)
b 1 200 - 0 / + 3,0
1 200 < b 1 500 - 0 / + 5,0
5.3. LENGTH TOLERANCES
Length tolerances of sheetsLength; l (mm) Length tolerance (mm)
2 000 - 0 / +8,2
2 500 - 0 / +8,5
3 000 - 0 / +8,8
6 000 - 0 / +10,6
Length tolerances of sheets can be calculated as follows:- 0/+ 7 mm basic tolerance, + 0.6 mm/m
12 DASZ-Dunaferr Steel Standard
5.4. fLATNESS
In case of ordering plain sheets the flatness tolerances, depending on the strength grades and width ranges according to EN 10051 standard, are included in the following table. Definiton of the strength grades (A, B, C, D) according to EN 10051 standard is included in chapter 2.
Width; b (mm) Flatness tolerance max. (mm/m)
A B C Db 1 200 15 18 23 as agreed
1 200 < b 1 500 18 23 30 as agreed
b > 1 500 23 28 38 as agreed
Patterned sheets flatness tolerance (mm/m)
Width; b (mm)Thickness; h (mm)
1.601.99 2.002.30 2.312.99 3.00 3.0112.008001 300 25 20 15 15 15
1 3011 540 20 15
6. DIMENSIONS
The dimensions are given by strength grades. Strength grades of different qualities are included in chapter 2. on product groups.
6.1. PLAIN PRODUCTS
Strength grade I. + II. + III.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
1.2 1.29 980 1 040
1.3 1.49 840 1 120
1.5 1.79 800 1 220
1.8 2.49 800 1 300
2.5 18 800 1 540
Strength grade IV.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
1.5 1.89 800 1 120
1.9 1.99 800 1 250
2 2.79 800 1 300
2.8 18 800 1 540
Strength grade V.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
1.8 1.99 800 1 040
2 2.79 800 1 250
2.8 2.99 800 1 420
3 18 800 1 540
Strength grade VI.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
2.5 2.99 800 1 040
3 3.19 800 1 300
3.2 3.49 800 1 400
3.5 18.00 800 1 540
Strength grade VII. + VIII.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
3 3.19 840 1 040
3.2 3.49 840 1 120
3.5 3.79 840 1 220
4.3 15.00 840 1 540
13DASZ-Dunaferr Steel Standard
6.2. PATTERNED PRODUCTS
Diamond
Strength grade I. + II. + III. + IV.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
1.8 1.99 840 1 040
2 2.49 800 1 220
2.5 2.99 800 1 300
3 16.5 800 1 540
Strength grade V.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
2.5 3.19 800 1 250
3.2 16.5 800 1 540
Strength grade I. + II. + III.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
1.6 1.79 840 1 040
1.8 1.99 840 1 300
2 2.99 800 1 300
3 16.5 800 1 540
Strength grade IV.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
1.6 1.89 840 1 040
1.9 1.99 840 1 250
2 2.99 800 1 250
3 16.5 800 1 540
Strength grade V.Thickness; h (mm) Width; b (mm)
Min. Max. Min. Max.
2.5 3.19 800 1 250
3.2 16.5 800 1 540
Teardrops
14 DASZ-Dunaferr Steel Standard
7. PACKAGING
Base types according to DASZ 34 standardProduct is identified by CODE 39 bar code labels.
7.1. SHEETS
7.1.1. Bundles with strapsLength (l) = 2 000 mmThickness (b) 3 mm
7.1.2. CORROSION PREVENITIVE PACKAGING
Length (l) = 2 000 mm
1. bundle number2. packaging material3. clamp4. self-adhesive label5. metal label6. colour marking7. banding strap8. edge protector
Bottom view of a packaged batch
1. Strap under the packaging material, below the strap used outside the packaging material
15DASZ-Dunaferr Steel Standard
7.2. WIDE COILS
7.2.1. Strapping of coils with coil eye in horizontal position
Width (b)
16
2012
.01.
ISD DUNAFERR CO. LTD.SALES
Address: H2400 Dunajvros, Vasm tr 13.H1022 Budapest, Bimb u. 17.
Phone: +36 (1) 500-4673 Fax: +36 (1) 500-4601
E-mail: [email protected]: www.isd-dunaferr.hu
8. APPROBATED (CERTIfIED) PRODUCTS
Hot rolled ship plates with normal and high steel strength and with normalized and thermo-mechanical rollingCertified by: DET NORSKE VERITAS
Materials for pressure equipment manufacturing: unalloyed structural steels, wide coil and plates from wide coil
a) approved according to AD 2000 MERKBLATT W0 Certified by: MI TV SD
b) approved according to PED 97/23/EC Certified by: MI TV SD
Materials for manufacturing railway bridge elements according to DBS 918002-2(Deutsche Bahn Q1 qualification; Deutsche Bahn HPQ manufacturer's conformity)Certified by: Deutsche Bahn
Hot rolled products for construction purposes with CE-mark according to CPD 89/106/EEC Certified by: Germanischer Lloyd.
The products made by ISD Dunaferr Co. Ltd. are always supplied with a Conformity Statement of Producer and agreement shall be reached about the type of statement at the time of placing the order. The available types of statements are included by standard MSZ EN 10204:2005.
Certifications are available on the www.isd-dunaferr.hu website.