Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Warehouse: Factory 20, 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
Index
Crimp Machines - Pages 3-13
S1 M 3
S2M / S2P 4
HM200 Ecoline AC & DC 5
S3 Ecoline AC and DC 6
S6 Ecoline AC and DC 7
S7 8
S10 Ecoline 9
S10i 10
HM325iB 11
HM375iB 12
HM480 13
Hose Cutting Saws -Pages 14—19
EM3 Ecoline 14
EM3 DC ( 12v and 24v ) 15
EM3 16
EM6.2 17
EM8 P 18
EM115 19
Assembly Equip and Skiving- Pages 20—25
UNE10—Fitting Inserter ( Pneumatic) 20
PR 10—Perforator ( Pin Pricker) 21
RG10—Hose Assembly Flushing / Cleaning 22
UVC - Hose Suction Unit for Cutting Debris 23
USM 2.2 - Manual Skiving Tool 24
USM 10 - Workshop 1 PH Skiving Machine 25
Pressure Testing Units - Pages 26-27
P160 Ecoline 26
P160 or P160B 27
Technical Information and Company Information - Pages 28-30 28—30
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected]
Warehouse: Factory 20, 191-195 Greens Road , Dandenong South, VIC 3175
www.hosecrimp.net.au
S1M – Portable Crimper with Hand Pump Operation
Crimp Force kn/tonne 750 / 75
No Grease Feature Yes
SAE R12 /4SP (straight fitting)
1”
90 Deg Elbow Fittings ½”
Industrial Hose 1 ¼”
Max Crimp Range 52mm
Crimp Path (die Size + 10mm)
10mm
Max Opening (without Dies)
52mm
Drive Method Manual
Die Series 261
Oil Capacity 0.32litre
Length x Width x Height 230 x 180 x 160
Weight 15 kg
Dies in Standard Package ( Die Length is 65mm)
17,20,24 + Stor-age Box
Optional Die Sizes Availa-ble for Purchase
6.8, 9, 12, 14, 28, 32,36, 40, 44, 47
Description and Features
- The S1M crimper is for the low volume user who has a requirement to crimp hoses in a repair type of environment rather than production. It is very portable and with a weight of only 15kg it can be easily taken on site. - This model is really aimed at the ½” hose market and below but for straight fittings can handle up to 1” 4 wire and 1 ¼” Industrial hoses. - The machine comes with 3 die sets ( see above) but there is a good range of extra dies which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. - Also available with air foot pump operation as S1P model - Crimping diameter is set with a micrometer and when crimp diameter is reached a light comes on ( no mechanical dead stop)
Page 3
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected]
Address: Unit 20, 191-195 Greens Road , Dandenong South, VIC 3175
www.hosecrimp.net.au
S2M – Portable Crimper with Hand Pump Operation S2P - Portable Crimper with Air Pump Operation
Crimp Force kn/tonne 900 / 90
No Grease Feature Yes
SAE R12 /4SP (straight fitting)
1 ¼ or -20
90 Deg Elbow Fittings 1” or -16
Industrial Hose 1 ¼”
Crimp Range 63mm
Crimp Path (die Size + 22mm)
22mm
Max Opening (without Dies)
77 mm
Drive Method Manual or Air
Die Series 263
Oil Capacity 0.75 litre
Length x Width x Height 500 x 420 x 440
Weight 32 kg
Dies in Standard Package ( Die Length is 65mm)
17,20,24, 28, 32,40 + Storage Box
Optional extra Die Sizes Available for Purchase
6.8, 9, 12, 14, 36, 44, 47
Description and Features
The S2M crimper is for the low volume user who has a requirement to crimp hoses in a repair type of environment rather than production but wants to crimp bigger hoses than S1M model. It is reasonably portable with a weight of 32kg it can be easily taken on site or put in a van or UTE
This model is really aimed at the 1” hose market and below in both straight and elbow fittings and 1 ¼” Industrial hoses.
The machine comes with 6 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 47mm
Also available with air foot pump operation as S2P model and S2A model and S2 DC for single phase and DC van operation
Crimping diameter is set with a micrometer and when crimp diameter is reached a light comes on ( no mechanical dead stop).
Page 4
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20, 191-195 Greens Road, Dandenong South, Vic 3175
www.hosecrimp.net.au
HM 200 Ecoline – Available in 1P, 3P and DC models
Crimp Force kn/tonne 1300 / 130
No Grease Feature Yes
SAE R12 /4SP (straight fitting)
1 ¼ or -20 ( can crimp -24 in 2SN and 4SP with 1 piece fitting)
90 Deg Elbow Fittings 1,1/2” or -24
Industrial Hose 2”
Maximum Crimp Diameter 70mm
Crimp Path (die Size + 30mm)
30mm
Max Opening (without Dies)
100 mm
Drive Method Hydraulic Power Pack
Die Series 239
Oil Capacity (litres) 40 AC, 4L DC model
Length x Width x Height 420 x 535 x 520
Weight 88 kg
Dies in Standard Package ( Die Length is 60mm to75mm)
17,20,24,28,32, 40,44,50
Optional extra Die Sizes Available for Purchase
6.8, 9, 12, 14, 16, 19,22,26, 36, 47,54,57,62
Description and Features
The HM200 ecoline crimper is for the workshop volume user who has a requirement to crimp hoses in a repair or medium production environment in a workshop or mobile van.
This model is really aimed at the 1 ¼” hose market and below in both straight and elbow fittings but is ca-pable of 1 ½” in 2SN or 4SP providing the crimping force required does not exceed 130 tonne.
The machine comes with 8 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm and up to 62mm
Crimping diameter is set with a micrometer and limit switch assuring accurate repeatable crimping
Page 5
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20, 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
S3 Ecoline – 1 ¼” Crimper. 1PH, 3PH, DC Options
Crimp Force kn/tonne 1200 / 120
No Grease Feature Yes
SAE R12 /4SP (straight fitting)
1 ¼ or -20
90 Deg Elbow Fittings 1 ¼” or -20
Industrial Hose 2”
Maximum Crimp Diameter 70mm
Crimp Path (die Size + 35mm)
35 mm
Max Opening (without Dies)
105 mm
Drive Method Hyd Power Unit
Die Series 239, 239L
Oil Capacity 35 litres
Length x Width x Height 592 x 545 x 672
Weight 150 kg
Dies in Standard Package ( Die Length is 65mm)
17,20,24, 28, 32,40,44,50
Optional extra Die Sizes Available for Purchase
6.8, 9, 12, 14,16,19,22, 26, 36, 47,57,62
Description and Features
The S3 ecoline crimper is for the workshop volume user who has a requirement to crimp hoses in a repair or medium production environment in a workshop or mobile van.
This model is really aimed at the 1 ¼” hose market and below in both straight and elbow fittings.
The machine comes with 8 die sets ( see above) but there is a good range of extra dies avail-able which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 62mm
The 1ph and 3ph models come with integral power unit and DC model comes on feet with a separately mounted 12vDC or 24vDC Power Unit
Crimping diameter is set with a micrometer and limit switch assuring accurate repeatable crimping
AC Version
DC Version 12v and 24v
Page 6
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20, 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
S6.2 Ecoline – 2” Crimper. 1PH, 3PH, DC Options
Crimp Force kn/tonne 2000 / 200
No Grease Dies Feature Yes
SAE R12 /4SP (straight fitting)
2”or –32
90 Deg Elbow Fittings 2” or –32
Industrial Hose 3 ”
Max Starting Crimp Dia 100 mm
Crimp Path die Size+45mm 45 mm
Max Opening (w/o Dies) 147 mm
Drive Method Hyd Power Unit
Die Series 239, 266L
Oil Capacity 50 litres
Length x Width x Height 700 x 600 x 735
Weight 248 kg AC model
Dies in Standard Package ( Die Length 40mm to 110mm ( depend on size)
17,20,24, 28, 32,40,44,50,57, 71+266.239L
Optional extra Die Sizes Available for Purchase
6.8, 9, 12, 14,16,19,22, 26, 36,47,54,62,67, 74,78,84,86,92
Description and Features
The S6 ecoline crimper is for the workshop ( or mobile) volume user who has a requirement to crimp hoses in a repair or medium production environment in a workshop or mobile van.
This model is really aimed at the 2” hose market and below in both straight and elbow fittings.
The machine comes with 10 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 92mm
The 3ph model comes with integral power unit and DC model comes on feet with a sepa-rately mounted 12vDC or 24vDC Power Unit
Crimping diameter is set with a micrometer and limit switch assuring accurate repeatable crimping
AC Version
DC Version 12v and 24v
Page 7
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected]
Address: Unit 20, 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
S7 – 2” Crimper. 1PH, 3PH, DC Options
Crimp Force kn/tonne 2400 / 240
No Grease Dies Feature Yes
SAE R12 /4SP/ R15 (straight fitting)
2”or –32
90 Deg Elbow Fittings 2” or –32
Industrial Hose 2 ”
Maximum Crimp Diameter 82 mm
Crimp Path die Size+24 mm 24 mm
Max Opening (w/o Dies) 110 mm
Drive Method Hyd Power Unit
Die Series 239L, 265
Oil Capacity 2.3 litres
Length x Width x Height 430 x 367 x 682
Weight 77 kg
Dies in Standard Package ( Die Length 40mm to 110mm ( depend on size)
17,20,24, 28, 32,40,44,50,57, 71+265.239L
Optional extra Die Sizes Available for Purchase
6.8, 9, 12, 14,16,19,22, 26, 36,47,54,62,67, 74,78
Description and Features
The S7 crimper is for the workshop ( or mobile) user who has a requirement to crimp hoses in a repair or medium production environment in a workshop or mobile van.
This model is really aimed at the 2” hose market and below in both straight and elbow fittings.
The machine comes with 10 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 78mm
The 24vDC model is really good for mobile van because a 240 tonne crimp force in a pack-age weighing only 77kg is a nice combination. Best fitted at back or side of van on slide out rails allowing large heavy and long hoses good access from underneath, giving good visibility.
Crimp dia is easily set by turning handles until socket touches and then crimp path by micrometer.
Page 8
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
S10 Ecoline – 2” Crimper. - 3Phase 4 kw
Crimp Force kn/tonne 2800 / 280
No Grease Dies Feature Yes
SAE R12 /4SP / 4SP / R15 2”or –32
90 Deg Elbow Fittings 2” or –32
Industrial Hose 4 ”
Maximum Crimp Diameter 139 mm
Crimp Path die Size+45mm 45 mm
Max Opening (w/o Dies) 190 mm
Drive Method Hyd Power Unit
Die Series 239L, 237L
Oil Capacity 50 litres
Length x Width x Height 690 x 600 x 850
Weight 390 kg
Dies in Standard Package ( Die Length 40mm to 110mm ( depend on size)
17,20,24, 28, 32,40,44,50,57, 71
Optional extra Die Sizes Available for Purchase
from6.8mm to 131mm
Description and Features
The S10 ecoline crimper is for the workshop low volume End User who has a requirement to crimp 2” hoses in a repair environment in a workshop or container on site
This model is really aimed at the 2”hose market and below in both straight and elbow fittings, but with the added capability of an extra 80 tonnes force than S6.2 Ecoline.
The machine comes with 10 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 131mm
Crimping diameter is set with a micrometer and limit switch assuring accurate repeatable crimping
Can crimp wide range of Industrial hoses up to 4” (depending on crimp force)
Page 9
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195, Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
S10i – 2” Crimper. - 3Phase 4 kw
Crimp Force kn/tonne 2800 / 280
No Grease Dies Feature Yes
SAE R12 /4SP / 4SH / R15 2”or –32
90 Deg Elbow Fittings 2” or –32
Industrial Hose 4 ”
Maximum Crimp Diameter 139 mm
Crimp Path die Size+45mm 45 mm
Max Opening (w/o Dies) 190 mm
Drive Method Hyd Power Unit
Die Series 239L, 237L
Oil Capacity 55 litres
Length x Width x Height 690 x 600 x 1400
Weight 390 kg
Dies in Standard Package ( Die Length 40mm to 110mm ( depend on size)
17,20,24, 28, 32,40,44,50,57, 71
Optional extra Die Sizes Available for Purchase
from6.8mm to 131mm
Description and Features
The S10i crimper is for the workshop volume user who has a requirement to crimp 2” hoses in a repair or medium production environment in a workshop or container on site
This model is really aimed at the 2”hose market and below in both straight and elbow fittings, but with larger opening than S6.2 Ecoline.
The machine comes with 10 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 131mm
Crimping diameter is set with a micrometer and limit switch assuring accurate repeatable crimping
Can crimp wide range of Industrial hoses up to 4” (depending on crimp force) For further in www.hosecrimp.net.au or contact us below
Page 10
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
HM325iB – 2” Crimper. - 3Phase 4kw
Crimp Force kn/tonne 2800 / 280
No Grease Dies Feature Yes
SAE R12 /4SP / 4SH /R15 2”or –32
90 Deg Elbow Fittings 2” or –32
Industrial Hose 4 ” and 6 “ using master die using Industrial die package
Maximum Crimp Diameter 165 mm
Crimp Path die Size+70 mm 70 mm
Max Opening (w/o Dies) 215 mm
Drive Method Hyd Power Unit
Die Series 239, 239L, 237L
Oil Capacity 100 litres
Length x Width x Height 1200 x 600 x 1700
Weight 750 kg
Dies in Standard Package ( Die Length 40mm to 110mm ( depend on size)
17,20,24, 28, 32,40,44,50,57, 71
Optional extra Die Sizes Available for Purchase
from6.8mm to 131mm
Description and Features
The HM325iB crimper is for the production volume user who has a requirement to crimp 2” hoses in a repair or high production environment.
This model is really aimed at the 2”hose market and below in both straight and elbow fittings, but with the added capability of a touch screen programmable controller
The machine comes with 10 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 131mm
Crimping diameter is set by program and 1000 part numbers can be stored and programmed Can crimp wide range of Industrial hoses up to 4” but can crimp 6” using master dies. The
Industrial dies package must be purchased to crimp the range of Industrial hoses.
Page 11
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
HM375iB – 2” Crimper. - 3Phase 4kw
Crimp Force kn/tonne 3150 / 315
No Grease Dies Feature Yes
SAE R12 /4SP / 4SH / R15(straight fitting)
3”or –48
90 Deg Elbow Fittings 3” or –48
Industrial Hose 4 ” using 237-dies and 6 “ using master dies.
Maximum Crimp Diameter 165 mm
Crimp Path die Size+70mm 70 mm
Max Opening (w/o Dies) 215 mm
Drive Method Hyd Power Unit
Die Series 239, 239L, 237L
Oil Capacity 100 litres
Length x Width x Height 1200 x 600 x 1700
Weight 750 kg
Dies in Standard Package ( Die Length 40mm to 110mm ( depend on size)
17,20,24, 28, 32,40,44,50,57, 71
Optional extra Die Sizes Available for Purchase
from6.8mm to 131mm
Description and Features
The HM375iB crimper is for the production volume user who has a requirement to crimp up to 3” hoses in a repair or high production environment.
This model is really aimed at the 3 ”hose market and below in both straight and elbow fittings, but with the added capability of a touch screen programmable controller
The machine comes with 10 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 131mm
Crimping diameter is set by program and 1000 part numbers can be stored and programmed Can crimp wide range of Industrial hoses up to 4” but can crimp 6” using master dies. The
Industrial dies package must be purchased to crimp the range of Industrial hoses. Many optional extras available, mirror, auto back stop, SPC, and rear camera
Page 12
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
HM480 – 3” Crimper. - 3Phase 5.5 kw
Crimp Force kn/tonne 4500 / 450
No Grease Dies Feature Yes
SAE R12 /4SP /R15 3”or –48
90 Deg Elbow Fittings 3” or –48
Industrial Hose 6” and up to 8” using master die or using Industri-al die package
Maximum Crimp Diameter 310 mm
Crimp Path die Size+150mm 150 mm
Max Opening (w/o Dies) 380 mm
Drive Method Hyd Power Unit
Die Series 239L, 237L, 245
Oil Capacity 300 litres
Length x Width x Height 1590 x 730x 2015
Weight 2600 kg
Dies in Standard Package ( Die Length 40mm to 110mm ( depend on size)
17,20,24, 28, 32,40,44,50,57, 71, + 237.239.2L2 + 245.237L
Optional extra Die Sizes Available for Purchase
from6.8mm to 200 mm
Description and Features
The HM480iB crimper is for the production volume user who has a requirement to crimp 3” hydraulic hoses in a repair or high production environment, large Industrial Hoses up to 10” in diameter
The machine comes with 10 die sets ( see above) but there is a good range of extra dies available which go down to 6.8mm which is often purchased for crimping of mini-test hoses and small thermoplastic hoses. The largest die available is 200mm
Crimping diameter is set by program and 1000 part numbers can be stored and programmed Can crimp wide range of Industrial hoses up to 8” but will crimp 10” using master dies. The
Industrial dies package must be purchased to crimp the range of Industrial hoses. Many optional extras available, mirror, auto back stop, SPC, and rear camera
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Warehouse: Factory 20, 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
EM3 Ecoline – 240v AC 1P Cutting Saw 1.8 KW
Hose Capacity (Workshop) R13 & R15
1” or -16
Hose Capacity ( R12) ( Workshop)
1 ¼ or -20
Hose Capacity Industrial 1 ¼” or -20
Max OD 52 mm
Noise Level 90 dBA
Brake Motor No
Suction Connection 40mm
Drive Method Manual
Cutting Blade TMG 200x1.6x 25.4
Length x Width x Height 400 x 510 x540
Weight 20 kg
Suction Adaptor Pt No 777.054
Description and Features The EM3ecoline is for the low and medium volume workshop or container use. Single Phase operation with 1.8 KW Drive High RPM motor designed for 1P operation
Page 14
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected]
Address: Unit 20 / 191-195 Greens Road, Dandenong South, Vic 3175
www.hosecrimp.net.au
EM3 – DC 12V or 24v for Mobile Vans (2.4 KW for 12V and 2.5 KW for 24V)
Hose Capacity ( (Workshop) R13 & R15
1 1/4 or –20
Hose Capacity ( High Production) R13 & R15
3/4 -or –12
Hose Capacity ( R12) ( Workshop)
1 1/4” or -20
Hose Capacity Industrial 2”
Max OD 80 mm
Noise Level 93 dBA
Brake Motor No
Suction Connection 40 mm
Drive Method Manual
Cutting Blade TM 250x2x40Z
Length x Width x Height 470 x 567 x 365
Weight 29 kg
Suction Adaptor Pt No 777.054
Description and Features
The EM3 DC is designed for mobile van or truck operator Available in 12v or 24v options Small, lightweight but powerful unit
Page 15
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794-0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
EM3 – AC 3P Cutting Saw for Workshop - 1.8 KW
Hose Capacity ( (Workshop) R13 & R15
1 1/4” or –20
Hose Capacity (High Production) R13 & R15
3/4” or –12
Hose Capacity ( R12) ( Workshop)
1 1/4” or -20
Hose Capacity Industrial 2”
Max OD 80 mm
Noise Level 80 dBA
Brake Motor Yes
Suction Connection 80 mm
Drive Method Manual
Cutting Blade TM275x3x30
Length x Width x Height 540 x 440 x 300
Weight 50 kg
Suction Adaptor Pt No 777.056
Description and Features
The EM3 is designed for the medium volume workshop or container use. Three Phase operation with 3 KW Drive Optional Spiral blade available for customers with large batches of spiral assemblies
Page 16
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
EM6.2 – 3PH Cutting Saw ( 2” Capacity) - 4.6 KW
Hose Capacity ( (Workshop) R13 & R15
2” or –32
Hose Capacity (High Production) R13 & R15
1 1/4” or –20
Hose Capacity ( R12) ( Workshop)
2” or –32
Hose Capacity Industrial 2”
Max OD 85 mm
Noise Level 90 dBA
Brake Motor Yes
Suction Connection 60 mm
Drive Method Manual
Cutting Blade TMG 350x3x30
Length x Width x Height 745 x 690 x 430
Weight 75 kg
Suction Adaptor Pt No 777.055
Description and Features The EM6.2 is designed for medium production workshop cutting up to 2” six wire
hoses 3 Phase Motor with 4.6 KW power Bench top model with improved handle design for good mechanical advantage Graduated table allowing pins to be accurately placed by hose size
Page 17
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road , Dandenong South, VIC 3175
www.hosecrimp.net.au
EM8P – 3PH Cutting Saw ( 2” Capacity) - Foot Pedal 4.6 KW
Hose Capacity ( (Workshop) R13 & R15
2” or –32
Hose Capacity (High Production) R13 & R15
1 1/4”” or –20
Hose Capacity ( R12) ( Workshop)
2” or –32
Hose Capacity Industrial 4 ”
Max OD 120 mm
Noise Level 90 dBA
Brake Motor Yes
Suction Connection 60 mm
Drive Method Pneumatic Cylinder and Foot Pedal
Cutting Blade TMG 400x4x30
Length x Width x Height 983 x 760 x 540
Weight 140 kg
Suction Adaptor Pt No 777.055
Description and Features The EM8 P is designed for medium production workshop cutting up to 2”
six wire hoses 3 Phase Motor with 4.6 KW power Bench top model with pneumatic foot pedal and cylinder for operator
ease of use Sliding cover with interlock to provide extra operator safety
Page 18
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
EM115 – 3PH Cutting Saw ( 3” Capacity) - Foot Pedal 7.5 KW
Hose Capacity ( (Production) R13 & R15
2” or –32
Hose Capacity (Workshop) R13 & R15
3” or – 48 ( with special blade)
Hose Capacity ( R12) ( Workshop)
3” or –48
Hose Capacity Industrial 3”
Max OD 125 mm
Noise Level 80 dBA
Brake Motor Yes
Suction Connection 108 mm
Drive Method Pneumatic Cylinder and Foot Pedal
Cutting Blade TMG 520x4x40
Length x Width x Height 1210 x 650 x 1650
Weight 245 kg
Suction Adaptor Pt No N /A
Description and Features
The EM115 is designed for high production workshop cutting up to 3” six wire hoses (note special blade required over 2” size)
Includes cutting counter, feed control, adjustable return speed Upright model with pneumatic footpedal and cylinder for operator ease of use
Pneumatic cover with interlock to provide extra operator safety.
Page 19
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
UNE10 Hose Fitting Inserter
Working Range Fittings up to 2”
Force 4.7 kn at 6 bar
Piston Stroke ( pneumatic cyl ) 100 mm
Weight 35 KG
L X W X H ( mm) 600 x 810 x 310
Description and Features
This unit is designed for workshops that make hose assemblies in batches
Takes away the need for operator banging hose fittings in with mallet Interlocked safety cover.
Has multiple adaptors to suit different shaped hose ends
Labour and time savings will pay for machine
Please contact below for quotation or further information. Our website is www.hosecrimp.net.au
Page 20
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
PR 10 Perforating Machine– for Pin Pricking Hoses
Working Range Hoses up to 45mm OD
Weight 8 KG
L X W X H ( mm) 290 x 150 x 330
Description and Features
This unit is to perforate hose covers for gaseous applications
Maximum Hose OD for this unit is 45mm Twin Pin Prick wheels for straight line perforation
Fully adjustable perforation depth
Page 21
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
RG 10 Hose Assembly Cleaning Machine
Flow Rate 180 l /min
Capacity ( litres) 215
Working Range Up to 2” hoses
Drive Method Diaphram Air Pump
L x Width x Height 2000 x 840 x 1050
Weight 160 kg
Cleaning Agent Water Emulsion
Filter 10 micron
Description and Features
This unit is designed for cleaning dirt from hose assemblies without the need to buy projectiles
Unit recirculates cleaning fluid and filters out particles Fluid is 95% water with a non toxic and anti-corrosion solution added
Page 22
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20, 191-195 Greens Road , Dandenong South, VIC 3175
www.hosecrimp.net.au
UVC Suction Device—Hose Cutting Debris with Built in Spark Arrester
Description and Features Designed to attach to most Uniflex cutting saws in order to contain rubber particles
and dust. Includes a spark arrester which is important to reduce any fire risk from sparks ig-
niting the built of rubber dust collected. Good investment to protect workers from ingesting minute rubber particles from the
air whilst cutting hoses, especially during multiple cuts Shows good Health and Safety adherence by management Different adapters available for different saws.
Page 23
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
USM2.2 Manual Skiving - Internal / External
Internal Skiving 5/8” up tp 2”
External Skiving 3/16” up to 2”
Noise Level N/A
Drive Method Manual
L x Width x Height 338 x 465 x 445
Weight 32 kg
Tool RPM N / A
Description and Features
This unit is designed for the predominantly non-skive assember who has an occasional need to Skive hoses but does not want to invest in a higher cost volume powered skiving machine
Unit is clamped in a vice and the hose is advanced whilst operator is turning the handle Able to take on site easily or become permanent equipment in mobile van
For quotation or further information contact us below or check our website www.hosecrimp.net.au
Page 24
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
USM10 Ecoline 1Ph Skiving - Internal / External
Internal Skiving 5/8” up tp 2”
External Skiving 3/16” up to 2”
Noise Level 60 dBA
Drive Method 0.37 KW—1 Phase
L x Width x Height 440 x 440 x 545
Weight 35 kg
Tool RPM 110
Description and Features
This unit is designed for the predominantly for medium batch skiving of hoses
Powered Unit for clean repeatable skiving both Internally and Externally Unit comes with full tools package
For quotation or further information please contact below or check our website www.hosecrimp.net.au
Page 25
Hose-Crimp - Australian Distributor for Uniflex
Phone: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
P160 Ecoline Hose Test Chamber
Test Pressure 150 bar to 1300 bar
Capacity ( litres) 33
Working Range Up to 2” hoses
Drive Method Air over water In-tensifier
L x Width x Height 1400x 600 x 1200
Weight 210 kg ( empty)
Testing Liquid Water Emulsion
Filter 10 micron
Stek O Adaptors (included) DN 4/6/8/10/12 /G1/2” (405.901)
Steck O Adaptors (included) R 1/4”, 3/8”, 1/2” and G 1/2” 405.902
Description and Features
Uses Staplok adaptors for quick install of next hose assembly
Lifting the lid dumps pressure. Self purge bleed valve eliminates air from assembly before pressurization
This model is designed for the user that needs test capability on a low volume basis and who wants a low initial investment but still requires accurate testing capability.
Page 26
Hose-Crimp - Australian Distributor for Uniflex
Phone: 03-9794 0602 Email: [email protected] Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au
P160 or P160B Hose Test Chamber
Test Pressure 150 bar to 1300 bar
Capacity ( litres) 100
Working Range Up to 2” hoses
Drive Method Air over water In-tensifier
L x Width x Height 2000 x 840 x 1050
Weight 210 kg ( empty)
Testing Liquid Water Emulsion
Filter 10 micron
Stek O Adaptors (included) DN 4/6/8/10/12 /G1/2” (405.901)
Steck O Adaptors (included) R 1/4”, 3/8”, 1/2” and G 1/2” 405.902
Description and Features
Uses Staplok adaptors for quick install of next hose assembly
The ‘B’ version includes touch screen control with laptop connection capability and programming Lifting the lid dumps pressure.
Self purge bleed valve eliminates air from assembly before pressurization
Larger models and production models available. ( please contact email below)
Page 27
56 Technische Änderungen vorbehalten. / We reserve the right to make technical changes without notice.
Presskraft(kN/ton)
Steue-rung
SAE R12 /4SP
Industrie90°
Bogenmax.Press-
bereichmax.Press-
wegÖffnungs-
wegÖffnung o.
BackenBackentyp
Geschwin-digkeit
Schliessen /Pressen /Öffnen
AntriebGeräusch-
pegelEcoline
Crimp force ControlSAE R12 /
4SPIndustry Elbows
Crimprange
Crimp path OpeningOpeningw/o dies
Type of dies
SpeedClose /Crimp /Open
Drive Noise level Ecoline
S 1 M 750 / 75Micro-meter
1” 1 1/4” 1/2” 52 mm 5 mm +10 mm 52 mm 261ManuellManual
S 1 P 750 / 75Micro-meter
1” 1 1/4” 1/2” 52 mm 5 mm +10 mm 52 mm 261DruckluftPressure
S 2 M 900 / 90Micro-meter
1” 1 1/4” 1” 63 mm 8 mm +22 mm 77 mm 263ManuellManual
S 2 P 900 / 90Micro-meter
1” 1 1/4” 1” 63 mm 8 mm +22 mm 77 mm 263DruckluftPressure
S 2 A 900 / 90Micro-meter
1” 1 1/4” 1” 63 mm 8 mm +22 mm 77 mm 2631 Phase
elektrischElectric
S 3 1200 / 120 Control A 1 1/4” 2” 1 1/2” 70 mm 8 mm +35 mm 105 mm 239 4 / 4 / 6,5 3 kW 69 dBA ✓
S 4 1800 / 180 B+ Touch 1 1/2” 2” 1 1/2” 70 mm 8 mm +35 mm 105 mm 2392,7 / 2,7
4,74 kW 69 dBA ✓
S 6 2000 / 200 B+ Touch 2” 3” 2” 100 mm 8 mm +45 mm 147 mm 239L / 266L 9,7 / 2,2 / 16 5,5 kW 69 dBA ✓
S 7 2400 / 240open /close
2” 2” 1 1/2” 82 mm 8 mm +24 mm 110 mm 239L / 265 - / 1,42 / - 0,55 kW 70 dBA
S 8 2200 / 220 Control A 2” 4” 2” 139 mm 8 mm +45 mm 190 mm 239L / 237L6,1 / 1,7 /
10,34 kW 69 dBA
S 10 2800 / 280 Control A 2” 4” 2” 139 mm 8 mm +45 mm 190 mm 239L / 237L6,1 / 1,7 /
10,35,5 kW 69 dBA
HM 200 1300 / 130 Control A 1 1/4” 2” 1 1/2” 70 mm 8 mm +30 mm 100 mm 2393,5 / 3,5 /
5,93 kW 69 dBA ✓
HM 220 1400 / 140 B+ Touch 1 1/4” 2” 1 1/2” 70 mm 8 mm +35 mm 105 mm 239 9,5 / 6 / 9,5 5,5 kW 53 dBA
HM 225 1600 / 160 B+ Touch 1 1/4” 2” 1 1/2” 70 mm 8 mm +40 mm 110 mm 239L 19 / 1,5 / 19 5,5 kW 53 dBA
HM 3 H 700 / 70 B+ Touch 3/4” 2” 1 1/2” 70 mm 8 mm +35 mm 105 mm 2398,6 / 8,6 /
10,55,5 kW 53 dBA
HM 325 2800 / 280 B+ Touch 2” 4” (6”) 3” 165 mm 20 mm +70 mm 215 mm 239L / 237L 23 / 1,6 / 33 4 kW 62 dBA
HM 375 3150 / 315 B+ Touch 3” 4” (6”) 3” 165 mm 20 mm +70 mm 215 mm 239L / 237L 23 / 1,6 / 33 4 kW 62 dBA
HM 380 3400 / 340 B+ Touch 3” 4” (6”) 3” 165 mm 20 mm +70 mm 215 mm 239L / 237L 23 / 1,5 / 33 4 kW 62 dBA
HM 420 3150 / 315 B+ Touch 2” 6” 3” 165 mm 20 mm +280 mm 280 mm 239L / 237L 29 / 2,1 / 29 5,5 kW 62 dBA
HM 480 4500 / 450 B+ Touch 3” 10” 3” 310 mm 80 mm +150 mm 380 mm239L / 237L /
24520 / 1,5 / 23 5,5 kW 62 dBA
HM 485 4500 / 450 B+ Touch 3” 10” 3” 250 mm 20 mm +310 mm 360 mm239L / 237L /
24520 / 1,5 / 23 5,5 kW 62 dBA
HM 502 5000 / 500 B+ Touch 3” 5” 2” 180 mm 30 mm +68,5 mm 240 mm239L / 237L /
55411 / 1,3 / 9,4 7,5 kW 62 dBA
HM 660 8000 / 800 B+ Touch 3” 10” 3” 325 mm 50 mm + 120 mm 395 mm239L / 232L /
24615 / 2 / 15 18,5 kW 69 dBA
HM 665 4500 / 450 B+ Touch 3” 10” 3” 380 mm 50 mm + 120 mm 450 mm239L / 237L /
24715 / 2 / 15 18,5 kW 69 dBA
HM 1200 12000 / 1200 B+ Touch 3” 10” 3” 325 mm 50 mm + 120 mm 395 mm239L / 237L /
24611 / 1,5 / 11 18,5 kW 69 dBA
lle Pressen auf einen Blick all crimpers at a glance Global Range
Page 28
Ha
lte
bo
lze
n f
ür
Sta
nd
ard
Pre
ss
ba
ck
en
/ P
ins
fo
r s
tan
da
rd d
ies
/ T
ou
rill
on
de
mo
rs s
tan
da
rd /
Go
rró
n d
e
mo
rdza
es
tán
da
r
262.
104.
426
2.12
9.3
239.
041.
423
9.04
1.4
(sw
)23
2.50
4.4
232.
505.
422
0.50
2.4
245.
114.
4
Pro
fil 2
62
x
Pro
fil 2
63
x
Pro
fil 2
39
xx
Pro
fil 2
66
x
Pro
fil 2
32
xØ
96
/ Ø
10
3
Pro
fil 2
37
x
Pro
fil 5
54
x
Pro
fil 2
45
x
Pro
fil 2
46
x
Pro
fil 2
47
x
Page 29
Customer world wideUNIFLEX Kunden weltweit
55
UNIFLEX INSIDE:Not everybody who works with UNIFLEX is aware of using an Uniflex hose crimper, for many leading com-panies from industries such as fluid power technology, mechanical engineering or automotive engineering use Uniflex as an Original Equipment Manufacturer (OEM) - which means they back on the legendary quality of Uniflex hose crimpers, often with special modification in accordance to the particular customer's product port-folio.So it is little wonder that companies such as Alfagomma, Anchor, Caterpillar, Eaton, Gates, Hansaflex, Parker, Pirtek, and many others frequently purchase "their" hose crimpers from UNIFLEX. Whether as a provider or as a user of special machinery for hose production: Make sure you also back on the know-how and expertise of the innovation leader - we will be glad to advise you!
Technische Änderungen vorbehalten. / We reserve the right to make technical changes without notice. Page 30
Hose-Crimp - Australian Distributor for Uniflex
PHONE: 03-9794 0602 Email: [email protected]
Address: Unit 20 / 191-195 Greens Road, Dandenong South, VIC 3175
www.hosecrimp.net.au