P42HHS10WP42HHA10WP-SU4H10W
C o p y P r o h i b i t e d
F U J I T S U G E N E R A L P r o p r i e t a r y
C O N T E N T S
IMPORTANT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SETTING SIGNALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
VIDEO MODE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
RGB MODE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
TROUBLESHOOTING USING LED AND OSD . . . . . . . . . . . . . . . . . . . 47
TROUBLESHOOTING FLOWCHART . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
VS AND Vd ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
GENERAL CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . 66
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71DISASSEMBLY .
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
TRANSPOR
VOLTAGE OF EACH CONNECTOR
TATION AND HANDLING RESTRICTIONS . . . . . . . . . . . 103
- 2 -
IMPORTANT INFORMATION
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THISPRODUCT TO RAIN OR MOISTURE.
Please use a screen saver to prevent burning of an after-image on the screen.
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your
personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD.
In order not to defeat the safeguards incorporated into this unit, observe the following basic rules governing its installation,
use and service. Please read these "Important Safeguards" carefully before use.
Read all the safety and operating instructions before operating the unit.
Retain the safety and operating instructions for future reference.
Adhere to all warnings on the unit and in the operating instructions.
Follow all operating instructions.
Unplug the unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not use attachments not recommended by the manufacturer as they may be hazardous.
Do not use the unit near water. Do not use the unit immediately after moving it from a low temperature to a high
temperature environment, as this causes condensation, which may result in fire, electric shock, or other hazards.
Do not place the unit on an unstable cart, stand, or table. The unit may fall, causing serious injury to a child or adult, and
serious damage to the unit. Mount the unit according to the manufacturer's instructions, using the mount recommended by
the manufacturer.
When the unit is used on a cart, avoid quick stops, excessive force, and uneven
surfaces which may cause the unit and cart to overturn, damaging the unit or
causing possible injury to the operator.
When transporting by car, place the unit as shown in the figure.
Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation and protect the unit from
overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the unit
on a bed, sofa, rug, or similar surface. The unit should not be placed in a built - in installation such as a bookcase or rack
unless proper ventilation is provided and the manufacturer's instructions are adhered to.) For proper ventilation, separate
the unit from other equipment, which may obstruct ventilation. Keep the unit at least 10cm from other equipment.
Operate only with the type of power source indicated on the label. If you are not sure of the type of power supply to your
home, consult your dealer or local power company.
This unit is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you cannot insert the plug
into the outlet, have an electrician install the proper outlet. Do not defeat the safety purpose of the grounded plug.
Route power cords so that they are not likely to be walked on or pinched by items placed on or against them. Pay
particular attention to cords at doors, plugs, receptacles, and where they exit from the unit.
For added protection during a lightning storm, or when the unit is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cabling. This will prevent damage to the unit by lighting and power line
surges.
Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in fire or
electric shock.
Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short-circuit
parts that could result in a fire or electric shock. Never spill liquid of any kind onto the unit.
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltages and
other hazards. Have all service done by qualified service personnel.
Unplug this unit from the wall outlet and have it serviced by qualified service personnel in the following cases:
a) If the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen onto the unit.
c) If the unit has been exposed to rain or water.
d) If the unit does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the Operation Manual, as improper adjustment of controls may result in damage and will often require
extensive work by a qualified technician to restore the unit to normal operation.
e) If the unit has been dropped or damaged in any way.
f) A distinct change in performance indicates that service is required.
When required, be sure the service technician uses replacement parts specified by the manufacturer or parts with the
same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Upon completion of any service of repairs, ask the service technician to perform safety checks to determine that the
unit is in proper operating condition.
Place the unit more than one foot away from heat sources such as radiators, heat registers, stoves, and other devices
(including amplifiers) that produce heat.
When connecting other devices such as VCR's and personal computers, turn off the power to this unit to protect
against electric shock.
Do not place combustibles such as cloth, paper, matches, aerosol cans or gas lighters that prevent special hazards
when overheated behind the cooling fan.
Use only the accessory cord designed for this unit to prevent shock.
The power supply voltage rating of this unit is AC100-240V, but the attached power cord conforms to the following
power supply voltage. Use only the Power Cord designated by our dealer to ensure Safety and EMC.
When used with other power supply voltages, the power cable must be changed.
Consult your local dealer.
Power Cord
Power supply voltage : AC 100 - 125 V AC 200 - 240 V AC-240V(SAA TYPE)
- 3 -
- 4 -
SPECIFICATIONS
Power requirement110-240V, 50/60Hz110-240V, 50/60Hz
4.3A-1.8A0.4A
PDP UNIT
Current drainSELECTOR UNIT
SELECTOR UNITPDP UNIT
Display panelScreen size 92.2(W) X 52.2(H) [cm]
UB type
36.3(W) X 20.6(H) [inch]Aspect ratio 16 : 9Number of pixels 1,024(H) X 1024(V) pixelsPixel pitch 0.90mm X 0.51mmContrast ratio 1000 : 1Luminance 1000 cd/m2Viewing angle Max. 160 degrees
Input/Output Terminals ofPDP unit
Input/Output Terminals ofSELECTOR unit
DVI input DVI-D terminal (HDCP)Differential Input 0.5 10%(RXC , RX0 , RX1 , RX2 )
Display frequency Horizontal : 33.75MHzVertical : 60HzDot clock : 40.5MHz
Digital(optical) audio input-27dB to -14.5dBLevel terminal10W+10W (L/R), 6
Effective max.output
Optical Input
1.0V /75Video input RCA terminal
S terminalY signal : 1.0V /75P-P
P-P
C signal : 0.286V /75P-P
Three RCA terminals(one system)
Component video input
Video input (E model)
Digital RGB1 input
Analog RGB2/RGB3 input
mD-sub : 15pin(3 row type)
SYNC signal : TTL level
DVI-D terminal (HDCP)
SCART terminal1.0V /75VideoY signal : 1.0V /75C signal : 0.286V /75
S video
G : 0.7V /75RGB
8 memories (each RGB1,2,3)User set mode
Display frequency
Digital RGB1 output
Analog audio input
Digital(optical) audioinput
Digital(optical) audiooutput
for Displayfor audio amp
PDP UNIT
PDP UNIT
PDP UNIT
SELECTOR UNIT
SELECTOR UNIT
SELECTOR UNIT Power cordRemote controllerBatteries (Type AA x 2)
Optical Input
Optical Input
-24dB to -14.5dB
Two RCA terminals(one system)500mVrms/22K
DVI-D terminal (HDCP)
Horizontal : 15.63 to 80.0MHzVertical : 50.0 to 120HzDot clock : 50MHz Max.
XGA 68MHz
-21dB to -15dB-21dB to -15dB
Environment (Operating)Temperature 0 to 40Relative humidity 20 to 80%Pressure 800 to 1,114 hPa
AccessoriesUser's manual
User's manual (only E model)
Power cordFerrite core (2)System cable (Video)System cable (Audio)
S video input
Color system NTSC/PAL/SECAM/N-PAL/M-PAL/4.43NTSC/PAL60
Display colors 16.7 million (256 each for R.G.B.)
Outer dimensionsWidth : 103.7cm (40.8 inch)Height : 64.2cm (25.3 inch)Depth : 8.5cm (3.3 inch)Width : 43.0cm (16.9 inch)Height : 9.5cm (3.7 inch)Depth : 37.0cm (14.6 inch)
Net weight28.5kg4.5kg
Y : 1.0V /75P-PPb/B-Y : 0.7V /75P-PPr/R-Y : 0.7V /75P-P
P-P
P-P
P-P
P-P
+
Differential Input 0.5 10%+
+ + + +
Differential Input 0.5 10%(RXC , RX0 , RX1 , RX2 )
++ + + +
(RXC , RX0 , RX1 , RX2 )+ + + +
Video : 0.7V /75P-P
B : 0.7V /75P-PR : 0.7V /75P-P
Model : P42HHS10W/E
- 5 -
EN55013EN55020
20011994
OptionsStand P-TT4200Wall mounting unit P-WB4200
P-CT4200
P-SP4200
0 to 15 mounting angle
0 to 15 mounting angleHanging unit
SpeakerP-ST4200Speaker stand
Standards
P42HHS10WSP42HHS10ES
P-SU4H10WSP-SU4H10ES
ASSafety : IEC60065 IEC60065EMC : AS/NZS 3548 AS/NZS 1053
EN60065 CE
Safety: EN60065
UL,CSASafety:UL6500 UL6500
C-UL C-ULEMC: FCC Part15 Class B FCC Part15 Class BICES-003 Class B ICES-003 Class B
EMC : EN55022EN61000-3-2 1995EN61000-3-3, 1995EN55024 1998
1998
EN61000-4-2, 1995EN61000-4-3, 1996EN61000-4-4, 1995EN61000-4-5, 1995EN61000-4-6, 1996EN61000-4-8, 1993EN61000-4-11,1994
- 6 -
Power requirement 110-240V, 50/60Hz4.4-1.9ACurrent drain
Display panelScreen size 92.0(W) X 51.8(H) [cm]
UB type
36.2(W) X 20.4(H) [inch]Aspect ratio 16 : 9Number of pixels 1,024 (H) X 1024 (V) pixelsPixel pitch 0.90mm X 0.51mm
Contrast ratio P42HHA10 1000 : 1 (typ.)Luminance 1000 cd/m (ryp.)Viewing angle Max. 160 degrees
2
EN55022 A1/A2Class BEN61000-3-2, 1995EN61000-3-3, 1995EN55024 1998EN61000-4-2, 1995EN61000-4-3, 1996EN61000-4-4, 1995EN61000-4-5, 1995EN61000-4-6, 1996EN61000-4-8, 1993EN61000-4-11, 1994
Input TerminalsVideo input BNC connector
1.0VP-P /75
S video input S terminalY signal:1.0VP-P /75C signal:0.286VP-P /75
Component Three BNC terminalsvideo input Y : 1VP-P /75
Pb /B-Y: 0.7VP-P /75Pr /R-Y: 0.7VP-P /75
RGB 2 input mD-sub:15pin (3 row type)Video : 0.7VP-P /75SYNC signal : TTL level
RGB 3 input BNC terminal x 5R: 0.7VP-P/75G: 0.7VP-P/75B: 0.7VP-P/75H: TTL level or 0.3VP-P /75V: TTL level or 0.3VP-P /75
User set mode 8 memories (each RGB1,2,3)Display frequency Horizontal :15.63 to 80.0MHz
Vertical : 50.0 to 120HzDot clock:50MHz Max
XGA 68MHz Max
RS-232C D-sub 9 pin terminal
Color system NTSC/PAL/SECAM/N-PAL/M-PAL/4.43NTSC/PAL60
Display colors 16.7 million (256 each for R.G.B.)
Audio input 2 pin terminals(three system)500mVrms/22k
Effective max. Level terminal 20W+20W (L/R), 4output
Dimensions Width : 103.5cm (40.7 inch)Height: 64.2cm (25.2 inch)Depth : 8.5 cm ( 3.3 inch)
Net weight 28.5kg
Environment (Operating)Temperature 0 to 40 CRelative humidity 20 to 80%Pressure 800 to 1,114 hPa
Accessories User's manualRemote controllerBatteries (Type AA x 2)Power cordFerrite core (2)
OptionsStand P-TT4200Wall mounting unit
P-WB4200mounting angle
mounting angle
0 to 15
Hanging unit
Speaker P-SP4200Speaker stand P-ST4200
P-CT4200
StandardsP42HHA10WP42HHA10E
ASSafety : I60065 A1/A2/A3/A4 I60065 A1/A2/A3/A4EMC : AS/NZS 3548 AS/NZS 3548
EN60065 1992A1 1993A2 1993A3 1995A4 1997
CESafety: EN60065 1992
A1 1993A2 1993A3 1995A4 1997
UL,CSASafety:UL6500 UL6500
CSA C22.2 No. CSA C22.2 No.EMC: FCC Part15 Class A FCC Part15 Class BICES-003 Class A ICES-003 Class B
EMC : EN55022 A1/A2Class AEN61000-3-2, 1995EN61000-3-3, 1995EN55024 1998EN61000-4-2, 1995EN61000-4-3, 1996EN61000-4-4, 1995EN61000-4-5, 1995EN61000-4-6, 1996EN61000-4-8, 1993EN61000-4-11,1994
0 to 15
RGB 1 input 24Pin DVI-D (HDCP) Differential Input 0.5V 10%(RXC , RX0 , RX1 , RX2 )
++ + + +
Model : P42HHA10W/E
SETTING SIGNALS
- 7 -
This display can store parameter settings for eight additional signals for RGB. To do this, select the desired signal and follow "RGB MODE ADJUSTMENT" in the manual to adjust the parameters.When you finish, the settings will be automatically stored.
FACTORY SET SIGNALS (RGB MODE)
Main corresponding signals (RGB mode)
* With some input signals, Out of range may appear even when the horizontal and vertical frequencies are within their permissible ranges. Makesure that the vertical frequency of the input signal is 85 Hz or less for SVGA, 75 Hz or less for XVGA/ SXGA , 60 Hz or less for UXGA.
640 x 480 31.47 59.94 VGA
640 x 480
640 x 480
37.50 75.00 VGA 75 Hz
43.27 85.01 VGA 85 Hz
720 x 400 31.47 70.09 400 lines
800 x 600 37.88 60.32 SVGA 60 Hz
800 x 600
800 x 600
46.88 75.00 SVGA 75 Hz
53.67 85.06 SVGA 85 Hz
1024 x 768
48.36 60.00 XGA 60 Hz1024 x 768
1024 x 768
1024 x 768
60.02
68.68
75.03
84.99
XGA 75 Hz
XGA 85 Hz
1280 x 1024 63.98 60.02 SXGA 60 Hz
1280 x 1024 79.98 75.03 SXGA 75 Hz
1600 x 1200 75.00 60.00
106.25 85.00 UXGA 85 Hz
UXGA 60 Hz
1600 x 1200
1360 x 768
848 x 480 31.02 60.00
852 x 480 31.72
47.71
59.97
60.01
720 x 485 15.73 59.94 60 fields
720 x 575 15.63 50.00 50 fields
Signal DVD-IDisplay (dots x lines) Horizontal frequency (kHz) Vertical frequency (Hz)
- 8 -
Horizontalfrequency (kHz)
Verticalfrequency (Hz)
Signal
15.73 SDTV 480i
15.63 SDTV 576i
31.47 SDTV 480p
31.25 SDTV 576p
45.00 HDTV 720p
37.50 HDTV 720p
33.75 HDTV 1,080i
28.13 HDTV 1,080i
FACTORY SET SIGNALS (Component video mode)
Pin No. Input signal Pin No. Input signal
1 Red 9
2 Green 10 Ground
3 Blue 11
124
5 Ground 13 Horiz. sync
6 Ground 14 Vert. sync
7 Ground 15
8 Ground Outer side Ground
Horizontalfrequency (kHz)
Verticalfrequency (Hz)
Signal
15.73 NTSC
15.63 PAL
15.63 SECAM
15.63 PAL 60
15.63 N-PAL
15.73 M-PAL
15.73 4.43 NTSC
FACTORY SET SIGNALS (Video, S-video mode)
The dedicated graphics card is optional.In the 800 x 600 and 1,024 x 768 modes, images of reduced size are displayed on the screen, using size reduction andinterpolation. Also note that on-screen information is also displayed in reduced size." Out of range" appears if the display receives a signal whose characteristic does not fall within the display'spermissible range.You can check the input signals with "Information" on the OTHERS Menu screen.
The sync switch (TTL/ANALOG switch) is onthe rear of the 13-pin horizontal sync and14-pin vertical sync terminals.
Pin No.
RGB INPUT TERMINAL
Pin No. No. signal
1 DCD (Data Carrier Detect)
2 RD (Receive Data)
3 TD (Transmit Data)
4 DTR (Data Terminal Ready)
5 GND (Ground)
6 DSR (Data Set Ready)
7 RTS (Request To Send)
8 CTS (Clear To Send)
9 RI (Ring Indication)
RS-232C INPUT TERMINAL
DVI-D INPUT TERMINAL
50.00
59.52
59.95
59.94
50.00
50.00
59.94
50.00
60.00
50.00
60.00
50.00
59.94
50.00
59.94
- 9 -
SCART TERMINAL
26101418
37111519
48121620
159131721
Pin No. Input Signal
1
2 Right audio
3
4 Audio ground
5 Blue ground
6 Left audio
7 Blue
Pin No. Input Signal
8
9 Green ground
10
11 Green
12
13 Red ground
14
Pin No. Input Signal
15 Red/chrominance
16
17
18 Composite video ground
19
20 Composite video/Y
21 Ground
Selector
3-pin outlet
3-pin outlet
DisplaySpeaker (optional)
CONNECTION
Model : P42HHS10W/E
BASIC SYSTEM CONNECTIONS
1. Connect the following items to the selector and the display
Selector and display
Connect these two with the provided system connection cable. (For details, see the page on the right.)a
Speakers
For how to connect speakers, see the instructions provided with the speakers.
2. Connecting the power cord
Connect the power plug of the display and selector power cords to a 3-pin outlet.
- 10 -
- 11 -
AUDIOINPUT
VIDEO1 VIDEO2 VIDEO4 VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEOVIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
S S S
Rear side of display
Left speaker cable Right speaker cable
RedBlack
Display input terminalPower input
Audio
To AC outlet
Rear side of selector
terminalPictureterminal
CONNECTING THE DISPLAY AND THE SELECTOR
Model : P42HHS10W
Remotecontrol
Display Speaker (optional)Speaker
Selector
VCR
DVD player
Amplifier
Satellite tuner
Video camera
Videogame machine
PC
EXAMPLE OF CONNECTION TO EXTERNAL COMPONENTS
Model : P42HHS10W/E
- 12 -
AUDIOINPUT
VIDEO1 VIDEO2 VIDEO4 VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEOVIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
S S S
To video output
To video input
Rear side of selector
To S-videooutput
To audio outputs
To audio inputs
To S-video input
VCRConnect the video signal cable to either the S-video input terminal or the video input terminal.
- 13 -
Model : P42HHS10W
AUDIOINPUT
VIDEO1 VIDEO2 VIDEO4 VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEOVIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
S S S
Rear side of selector
To digital audio input
To analog audio input
To analog audio output To digital audio output
AUDIOINPUT
VIDEO1 VIDEO2 VIDEO4 VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEOVIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
S S S
Rear side of selector
To S-videooutput
To componentvideo output
To video output
To audio outputs
To audioinputs To video input
To component video inputTo S-video input
DVD PLAYER
AMPLIFIER
Connect the video signal cable to the component video input terminal, S-video input terminal, or the video input terminal.
Connect the audio signal cable to either the digital output or the analog audio output.The signal input as digital input is not output as analog audio.The digital audio input terminal on the display complies with a sampling frequency of 48 kHz.In the case of outputs with another frequency, connect to an audio system (amplifier) .
If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
- 14 -
AUDIOINPUT
VIDEO1 VIDEO2 VIDEO4 VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEOVIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
S S S
To S-videooutput
To componentvideo output
To video output
To audio outputs
To audioinputs To video input
To component video input
To S-video input
SATELLITE TUNERConnect the video signal cable to the component video input terminal, S-video input terminal, or the video input terminal.If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
- 15 -
To S-video input
To video and audio outputs
To S-video output
To video and audio inputs
To S-video input
To video and audio outputs
To S-video output
To video and audio inputs
Front side of selector
VIDEO CAMERA
VIDEOGAME MACHINE
A video camera can conveniently be connected to the Video 3 input on the front side.Connect the video signal cable to either the S-video input terminal or the video input terminal.If the unit to be connected is equipped with S-video output terminal, it is recommended to connect to the S-video terminal.
As the connecting cable differs with videogame machines, please consult the instructions for your videogame machine.Connect the video signal cable to either the S-video input terminal or the video input terminal.Ensure that the same image (pattern) is not displayed on the screen for an extended period. If the same image is displayed on thescreen for an extended period, the brightness of that part of the screen may change and image burn-in may leavean after-image on the screen.If the videogame machine to be connected is equipped with S-video output terminal, it is recommended to connect to theS-video terminal.
Model : P42HHS10W/E
- 16 -
AUDIOINPUT
VIDEO1 VIDEO2 VIDEO4 VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEOVIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
S S S
PCAs the cable for connecting a PC differs with the PC model, please consult your dealer for information on the right cable to purchase.The PC can be connected to either the front side or the rear side, whichever is most convenient.
To RGB output (mD-sub)
To audio output
To audio input (mD-sub)To RGB3 input
When connecting to the front side of the selector
When connecting to the rear side of the selector
To RGB output (mD-sub)To audio output To audio
input
To RGB1 input(DVI-D)
To RGB2 input(mD-sub)
To RGB output (DVI-D)
- 17 -
Model : P42HHS10W
- 18 -
Model : P42HHS10E
AUDIOINPUT
VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
VIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
SCART SCARTSCART
Rear side of display
Left speaker cable Right speaker cable
RedBlack
Display input terminalPower input
Audio
To AC outlet
Rear side of selector
terminalPictureterminal
AUDIOINPUT
VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
VIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
SCART SCARTSCART
To SCART output
To SCART input
Rear side of selector
VCR
Connect the video signal cable to the SCART terminal.
- 19 -
AUDIOINPUT
VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
VIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
SCART SCARTSCART
Rear side of selector
To digital audio input
To analog audio input
To analog audio output To digital audio output
AUDIOINPUT
VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
VIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
SCART SCARTSCART
To component videooutput
To audio outputs
To audio inputs
To componentvideo input
Rear side of selector
To SCART output
To SCART input
DVD PLAYER
AMPLIFIER
Connect the video signal cable to either the component video terminal or the SCART terminal.If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
Connect the audio signal cable to either the digital output or the analog audio output.The signal input as digital input is not output as analog audio.The digital audio input terminal on the display complies with a sampling frequency of 48 kHz.In the case of outputs with another frequency, connect to an audio system (amplifier) .
- 20 -
AUDIOINPUT
VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
VIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
SCART SCARTSCART
To SCART output
To To audio inputs
To audio outputs
To component videooutput
To componentvideo input
SCART input
SATELLITE TUNER
Connect the video signal cable to either the component video terminal or the SCART terminal.If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
Rear side of selector
- 21 -
AUDIOINPUT
VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
VIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
SCART SCARTSCART
PCAs the cable for connecting a PC differs with the PC model, please consult your dealer for information on the right cable to purchase.The PC can be connected to either the front side or the rear side, whichever is most convenient.
To RGB output (mD-sub)
To audio output
To RGB output (mD-sub)To audio output To audio
input
To RGB1 input To RGB2 input(DVI-D) (mD-sub)
To RGB output (DVI-D)
To audio input (mD-sub)To RGB3 input
When connecting to the front side of the selector
When connecting to the rear side of the selector
- 22 -
- 23 -
Model : P42HHA10W/E
EXAMPLE OF CONNECTION TO EXTERNAL COMPONENTS
Remotecontrol
Display Speaker (optional)Speaker
VCR
DVD player
Satellite tuner
PC
To S-video output
To video output
To audiooutputs
To audio inputs To S-video input To video input
VCR
Connect the video signal cable to either the S-video input terminal or the video input terminal.
Bottom of Display (Ex.: P42VHA10)
- 24 -
Model : P42HHA10W
To S-video outputTo component video output
To video output
To S-video outputTo component video output
To video output
To audiooutputs
To audio outputs
To audioinputs
To video input
Tocomponentvideo input
To S-videoinput
To audioinputs
To video inputTo S-videoinput
Bottom of Display (Ex.: P42VHA10)
Bottom of Display (Ex.: P42VHA10)
DVD PLAYER
SATELLITE TUNER
Connect the video signal cable to the component video input terminal, S-video input terminal, or the video input terminal.If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
Connect the video signal cable to the component video input terminal, S-video input terminal, or the video input terminal.If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
- 25 -
Bottom of Display (Ex.: P42VHA10)
PCAs the cable for connecting a PC differs with the PC model, please consult your dealer for information on the right cable to purchase.The PC can be connected to either the front side or the rear side, whichever is most convenient.
To RGB output (DVI-D)To RGB output (mD-sub)
To audio output
To audio
To RGB2input(mD-sub)
inputTo RGB1 input(DVI-D)
- 26 -
An example of the underside of the display(with the P-TE1010E installed in the P42VHA10)
To video output
To S-video output
To audio output
To video inputTo S-video inputTo audio input
VCR
Connect the video signal cable to the SCART terminal. (When the P-TE1000E is installed.)Connect the video signal to either the S-video input terminal or the video input terminal. (When the P-TE1010E is installed.)
To SCART output
To SCART input
An example of the underside of the display(with the P-TE1000E installed in the P42VHA10)
- 27 -
Model : P42HHA10E
DVD PLAYERConnect the video signal cable to either the component video terminal or the SCART terminal. (When the P-TE1000E is installed.)Connect the video signal cable to the component video input terminal, S-video input terminal, or thevideo input terminal. (When the P-TE1010E is installed.)If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
To SCART output
To component video output
To audio output
To audio input
To componentvideo input
To SCART input
An example of the underside of the display(with the P-TE1000E installed in the P42VHA10)
An example of the underside of the display(with the P-TE1010E installed in the P42VHA10)
To component video output
To video output
To S-video output
To audio output
To audio input To S-video inputTo componentvideo input
- 28 -
To component video output
To audio output
To audio input
To componentvideo input
To SCART output
To SCART input
An example of the underside of the display(with the P-TE1000E installed in the P42VHA10)
An example of the underside of the display(with the P-TE1010E installed in the P42VHA10)
To component video output
To audio output
To S-video output
To video output
To audio inputTo componentvideo inputTo S-video input
To video input
SATELLITE TUNERConnect the video signal cable to either the component video terminal or the SCART terminal. (When the P-TE1000E is installed.)Connect the video signal cable to the component video input terminal, S-video input terminal, or thevideo input terminal. (When the P-TE1010E is installed.)If the component to be connected is equipped with component video output terminal, it is recommended to connect to thecomponent video terminal.
- 29 -
An example of the underside of the display(with the P-TE1000E installed in the P42VHA10)
PC
As the cable for connecting a PC differs with the PC model, please consult your dealer for information on the right cable to purchase.The PC can be connected to either the front side or the rear side, whichever is most convenient.
To RGB output (DVI-D)To RGB output (mD-sub)
To audio output
To audio input
To RGB2
To RGB1 input(DVI-D)
input(mD-sub)
- 30 -
Remotecontrol
Display Speaker (optional)Speaker
PC
EXAMPLE OF CONNECTION TO EXTERNAL COMPONENTS
- 31 -
Bottom of Display (Ex.: P42VHA10)
PCAs the cable for connecting a PC differs with the PC model, please consult your dealer for information on the right cable to purchase.The PC can be connected to either the front side or the rear side, whichever is most convenient.
To RGB output (DVI-D)To RGB output (mD-sub)
To audio output
To audio input To RGB1 input(DVI-D)
To RGB2input(mD-sub)
- 32 -
[MODE]Input mode selector button
Power indicator lamp
Remote control signal receiver
Input mode selector button[MODE]
Switches between picture input modes.VOL + buttonVOL - buttonAdjusts the sound volume.Wide screen selector button [WIDE]Switches the screen over to a desired wide screen.ON/OFF buttonTurns the power "ON" and "OFF (standby state)".
(Right section)
Control Panel (Right side of display)
DISPLAY SECTION FRONT
This lamp shows the state of the power supply.Lit (red): Stand-byLit (green): Power ONLit (orange): Power saving (DPMS: Power saving
Flashing (red): Malfunction (Flashes differently dependingfunction) mode ON
on the type of malfunction.)
Receives signals from the remote control.
PART NAMES AND FUNCTIONS
- 33 -
power switchWhen pressed while in the "OFF" state, the power indicator lamp lights and the display is placed in the "ON " state, and thepower can be turned "ON" or "OFF" by the remotye control or on the control panel of the display. When passed while in the "ON " state, the power indicator lamp goes out and the display is placed in the "OFF" state.Display input (picture) terminalConnect this terminal to the display output terminal on the tuner using the special cable provided.Display input (audio) terminalConnect this terminal to the display output terminal on the tuner using the special cable provided.External speaker output terminal (EXT SP)Connect this terminal to the optionally available speaker.When connecting a cable, attach a ferrite core to the cable.*See the speakerer instruction manual for more information. Power input terminalConnect this terminal to the power cable supplied with the display.
DISPLAY SECTION LOWER PART
Model : P42HHS10W/E
- 34 -
/I power switchWhen pressed while in the "OFF" state, the power indicator lamp lights and the display is placed in the "ON " state, and the powercan be turned "ON" or "OFF" by the remote control or on the control panel of the display. When pressed while in the "ON " state,the power indicator lamp goes out and the display is placed in the "OFF" state where power is still partly supplied.RS-232C terminal (RS-232C)This terminal is provided for you to control the display from the PC. Connect it to the RS-232C terminal on the PC.When connecting a cable, attach a ferrite core to the cable.RGB1 input terminal (RGB1 INPUT/DVI-D)Connect this terminal to the PC's display (digital RGB) output terminal.*The connection cable No.88741-8000 made by molex Inc. is recommanded.RGB2 input terminal (RGB2 INPUT/mD-sub)Connect this terminal to the PC's display (analog RGB) output terminal or decoder (digital broadcast tuner, etc.) output terminal.Power input terminalConnect this terminal to the power cable supplied with the display.When connecting a cable, attach a ferrite core to the cable.External speaker output terminal (EXT SP)Connect this terminal to the optionally available speaker.When connecting a cable, attach a ferrite core to the cable.*See the speaker instruction manual for more information.Audio1 input terminal (AUDIO1 INPUT)Audio2 input terminal (AUDIO2 INPUT)Audio3 input terminal (AUDIO3 INPUT)Connect this terminal to the sound output terminal of your VCR, etc.
Bottom
DISPLAY SECTION LOWER PART
Model : P42HHA10W
- 35 -
Component video input terminal (VIDEO3 INPUT)Connect this terminal to the component video output (color difference output) terminal of your HDTV unit or DVD player.S-Video input terminal (VIDEO2 INPUT)Connect this terminal to the S-video output terminal of your VCR.Video input terminal (VIDEO1 INPUT)Connect this terminal to the video output terminal of your VCR.Component video input terminal (VIDEO4 INPUT)Connect this terminal to the component video output (color difference output) terminal of your HDTV unit or DVD player.
/I power switchWhen pressed while in the "OFF" state, the power indicator lamp lights and the display is placed in the "ON " state, and the power can be turned"ON" or "OFF" by the remote control or on the control panel of the display. When pressed while in the "ON " state, the power indicator lamp goesout and the display is placed in the "OFF" state where power is still partly supplied.RS-232C terminal (RS-232C)This terminal is provided for you to control the display from the PC. Connect it to the RS-232C terminal on the PC.When connecting a cable, attach a ferrite core to the cable.RGB1 input terminal (RGB1 INPUT/DVI-D)Connect this terminal to the PC's display (digital RGB) output terminal.*The connection cable No.88741-8000 made by molex Inc. is recommanded.RGB2 input terminal (RGB2 INPUT/mD-sub)Connect this terminal to the PC's display (analog RGB) output terminal or decoder (digital broadcast tuner, etc.) output terminal.Power input terminalConnect this terminal to the power cable supplied with the display.When connecting a cable, attach a ferrite core to the cable.External speaker output terminal (EXT SP)Connect this terminal to the optionally available speaker.When connecting a cable, attach a ferrite core to the cable.*See the speaker instruction manual for more information.Audio3 input terminal (AUDIO3 INPUT)Audio2 input terminal (AUDIO2 INPUT)Audio1 input terminal (AUDIO1 INPUT)Connect this terminal to the sound output terminal of your VCR, etc.
+ RGB3 input terminal (RGB3 INPUT/BNC)Connect this terminal to the PC's display (analog RGB) output terminal or decoder (digital broadcast tuner,etc.) output terminal.*When RGB3 input terminal is connected, Comp.video mode is not available.Component video input terminal (VIDEO4 INPUT)Connect this terminal to the component video output (colour difference output) terminal of your HDTV unit or DVD player.*When Comp.video input terminal is connected, RGB3 mode is not available.RGB3 synchronization switch (SYNC SW TTL/ANALOG (75 ))This switch is used to terminate horizontal (H) terminal and vertical (V) terminal, out of RGB3 input terminals, with 75 .
TTL : Does not terminate. ANALOG (75 ): Terminates.
Bottom
VideoboardP-TE1000E type P-TE1010E type
Model : P42HHA10E
DISPLAY SECTION - LOWER PART
- 36 -
Video1 input terminal (VIDEO1 INPUT/P-TE1000E)Connect this terminal to the SCART terminal of your VCR or DVD, etc.S-Video input terminal (VIDEO2 INPUT/P-TE1010E)Connect this terminal to the S-video output terminal of your VCR.Video input terminal (VIDEO1 INPUT/P-TE1010E)Connect this terminal to the video output terminal of your VCR.Component video input terminal (VIDEO3 INPUT/P-TE1010E)Connect this terminal to the component video output (colour difference output) terminal of your HDTV unit or DVD player.
/I power switchWhen pressed while in the "OFF" state, the power indicator lamp lights and the display is placed in the "ON " state, and the powercan be turned "ON" or "OFF" by the remote control or on the control panel of the display. When pressed while in the "ON " state,the power indicator lamp goes out and the display is placed in the "OFF" state where power is still partly supplied.RS-232C terminal (RS-232C)This terminal is provided for you to control the display from the PC. Connect it to the RS-232C terminal on the PC.When connecting a cable, attach a ferrite core to the cable.RGB1 input terminal (RGB1 INPUT/DVI-D)Connect this terminal to the PC's display (digital RGB) output terminal.*The connection cable No.88741-8000 made by molex Inc. is recommanded.RGB2 input terminal (RGB2 INPUT/mD-sub)Connect this terminal to the PC's display (analog RGB) output terminal or decoder (digital broadcast tuner, etc.) output terminal.Power input terminalConnect this terminal to the power cable supplied with the display.When connecting a cable, attach a ferrite core to the cable.External speaker output terminal (EXT SP)Connect this terminal to the optionally available speaker.When connecting a cable, attach a ferrite core to the cable.*See the speaker instruction manual for more information.Audio3 input terminal (AUDIO3 INPUT)Audio2 input terminal (AUDIO2 INPUT)Audio1 input terminal (AUDIO1 INPUT)Connect this terminal to the sound output terminal of your VCR, etc.
Bottom
DISPLAY SECTION LOWER PART
- 37 -
RGB3 input terminal (RGB3 INPUT/BNC)Connect this terminal to the PCs display (analog RGB) output terminal.RGB3 synchronization switch (SYNC SW TTL/ANALOG (75 ))This switch is used to terminate horizontal (H) terminal and vertical (V) terminal, out of RGB3 input terminals, with 75 .
TTL : Does not terminate.ANALOG (75 ) : Terminates.
Power indicator lampThis lamp shows the state of the power supply.
Lit (red): Stand-byLit (green): Power ONLit (orange): Power saving (DPMS: Power saving function) mode ONFlashing (red): Malfunction
Remote control signal receiverReceives signals from the remote control.POWER buttonTurns the power "ON" and "OFF".* Even when the power is "OFF", some parts are still powered.Video3, S-video input terminal *Connect this terminal to the S-video output terminal of your VCR, etc. Video3, video input terminal *Connect this terminal to the video output terminal of your VCR, etc.Audio input terminals (L/R)These are the audio input terminals for the Video3 and RGB3 terminals.Input the audio for the video to be seen here.RGB3 input terminalConnect this terminal to your PC's mD-sub output terminal.
* On selecting the video input format
SELECTOR SECTION FRONT
Model : P42HHS10W/E
- 38 -
AUDIOINPUT
VIDEO1 VIDEO2 VIDEO4 VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEOVIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
S S S
Audio input terminalsInput audio through the terminals corresponding to the used video input terminals.The digital input terminals can be matched as desired with the remote control.Audio output terminalsFor use when the sound from an audio system (amplifier) is used.Video1 input terminalVideo2 input terminalVideo4 input terminalConnect this terminal to the component video output terminal, S-video output terminal, or video output terminal ofyour VCR or DVD, etc.Video5 input terminalVideo6 input terminalConnect this terminal to the component video output terminal of your DVD, etc.RGB1 input terminalConnect this terminal to the monitor (DVI-D) output terminal of your PC.RGB2 input terminalConnect this terminal to the monitor (mD-sub) output terminal of your PC.Display output terminals (Picture/Audio)Connect these terminals to the picture input terminal and audio input terminals on the display.Power input terminalConnect this terminal to the power cable supplied with the display.
SELECTOR SECTION REAR
Model : P42HHS10W
- 39 -
AUDIOINPUT
VIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITAL
AUDIOOUTPUT
DISPLAY OUTPUT
VIDEO2 VIDEO4
mD-sub
PICTURE AUDIO
VIDEO5 VIDEO1
Y PB/CB PR/CR
COMPONENT VIDEO
Y PB/CB PR/CR
COMPONENT VIDEORGB2
RGB1DVI
SCART SCARTSCART
Audio input terminalsInput audio through the terminals corresponding to the used video input terminals.
* The digital input terminals can be matched as desired with the remote control.
Audio output terminalsFor use when the sound from an audio system (amplifier) is used.Video1 input terminalVideo2 input terminalVideo4 input terminalConnect this terminal to the SCART terminal of your VCR or DVD, etc.
Video5 input terminalVideo6 input terminalConnect this terminal to the component video output terminal of your DVD, etc.
RGB1 input terminalConnect this terminal to the monitor (DVI-D) output terminal of your PC.RGB2 input terminalConnect this terminal to the monitor (mD-sub) output terminal of your PC.Display output terminals (Picture/Audio)Connect these terminals to the picture input terminal and audio input terminals on the display.
Power input terminalConnect this terminal to the power cable supplied with the display.
Model : P42HHS10E
SELECTOR SECTION REAR
- 40 -
button Switches between power ON and standbystate.
DISPLAY OFF button For showing on-screen-information.PICTURE MODE button Switches the picture mode.AUDIO IN button Selects the input audio.Video input mode selector button[VIDEO 1 - 6] Selects VIDEO 1 - 6RGB input mode selector button[RGB 1 - 3] Selects RGB 1 - 3.Menu button [MENU] Use this button to display a desired menufor adjusting the picture.Enter button [ENTER] Press this button to finalize the selection ofa desired menu or option within a menu.
STILL button Displays a still picture during viewing.MUTE button Temporarily mutes the sound.PICTURE MEMORY button Recalls the PICTURE MEMORY.WIDE button Switches the screen over to a desired widescreen.
OFF-TIMER Sets when the power should be turned of f.Volume adjustment buttons[VOL +/- ] Adjust the volume.Press the + button to increase the volume.Press the - button to reduce the volume.
Adjustment buttons [ / / / ]
Use these buttons to scroll through optionsin a menu.
REMOTE CONTROL
Model : P42HHS10W/E
- 41 -
button Switches between power ON and standbystate.
DISPLAY OFF button For showing on-screen-information.
PICTURE MODE button Switches the picture mode.
RGB input mode selector button[RGB 1 - 2] Selects RGB 1 - 2.
Video input mode selector button[VIDEO 1 - 3] Selects VIDEO 1 - 3.
Menu button [MENU] Use this button to display a desired menufor adjusting the picture.Enter button [ENTER] Press this button to finalize the selection ofa desired menu or option within a menu.
MUTE button Temporarily mutes the sound.
PICTURE MEMORY button Recalls the PICTURE MEMORY.
WIDE button Switches the screen over to a desired widescreen.
RGB3/VIDEO4 input mode selectorbutton [RGB3/VIDEO4] Selects RGB3 or VIDEO4.
Volume adjustment buttons[VOL +/ - ] Adjust the volume.Press the + button to increase the volume.Press the - button to reduce the volume.
Adjustment buttons [ / / / ]Use these buttons to scroll through optionsin a menu.
Model : P42HHA10W/E
REMOTE CONTROL
- 42 -
- 43 -
VIDEO MODE ADJUSTMENT
MENU
ENTERVIDEO 1
Normal
Wide 1
Wide 2
Position Horizontal "-"
Horizontal "+"
Vertical "-"
Vertical "+"
Size Width "-"
Width "+"
Height "-"
Height "+"
Zoom 1
Zoom 2
PICTURE
POSITION/SIZE
REMOTE CONTROLLER
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
VIDEO 6
RGB 1
RGB 2
RGB 3
VOL. +
VOL. -
STILL
MUTE
DISPLAY
PICTURE MODE DynamicFineReal 1Real 2Static
PICTURE MEMORY
AUDIO IN
OFF-TIMER
WIDE
DynamicFineReal 1Real 2Static
OffMin.Std.Max.
OffMin.Mid.Max.
Horizontal {-30 to +30 (Comp. video -16 to +16)}
{-3 to +12 (Comp. video -2 to +16)}
{-6 to +6}
{-6 to +6}
{-10 to +10}
{-3 to +12 (Comp. video -2 to +16)}
{-7 to +7 (Zoom -15 to +15) (Comp. video -16 to +16)}Vertical
Off30min.60min.90min.120min.
Analog AudioDigital Audio 1Digital Audio 2
Contrast {-30 to +30}
{-30 to +30}
{-16 to +16}
{-60 to +60}
{-60 to +60}
Brightness
Color
Tint
Sharpness
Picture Mode
Precision Setting
Picture Memory
Noise Reduction
NormalAutoWide 1Wide 2Zoom 1Zoom 2
FEATURES
Function
On Screen Menu
Input Terminal
Others
AUDIO
Luminance {40 to 100%}
{-15 to +15}
{-3500 to +3500}
Can be set when Fine isselected as the Picture Mode.Black Level
Colour Temp.
User Color Temp.
Video Input 1
Video Input 2
Video Input 3
Video Input 4
DVI Input
Power saver
OSD
Language
Name Select
24 Frame Mode
Jaggies Filter
FACTORY DEFAULT
Treble
Bass
Balance
Loudness
Load
Save
Execute
Position
Adjustment* Clamp Position* *Only Comp. Video{-8 to +8}
Size WidthHeight
YesNo
Default
White Screen
YesNo
YesNo
Default
Auto Off - UNTOUCH
Auto Off - NO SIG.
Red {0 to 255}{0 to 255}{0 to 255}
GreenBlue
OnOff
DVI 1DVI 2
OnOff
OnOff
OnOff
ModeFreq. Scan ModeInput SignalFreq.
OnOff
On(OSD : bright)On(OSD : dark)Off
}
Exhibition Mode
Illumination
Information
Memory 1Memory 2Memory 3Memory 4Memory 5Memory 6Memory 7Memory 8
EnglishDeutschEspanolFrancaisItalianoPortugues
Video 1
Video 2
Video input
Video Format
Video 3
Video 4
Video 5
Video 6
Video 1DVD 1DVD 2VCR 1VCR 2GAMECamcorderSTBSatelliteCable TV
Load
Save
Memory 1Memory 2Memory 3Memory 4Memory 5Memory 6Memory 7Memory 8
~
~