-7032 -7042
Extrusion End CapsFor 8 Series (Slot Width 10mm) Aluminum Extrusions
QThree-Sided Caps for Corners
MMaterial: Polyamide
MMaterial: Polyamide (Black, Light Gray, Yellow)
QScrew Mounted
QPlates for High Rigidity Type
8 Series10 40, 80
HFCB8-4040(Screw Fixing Type)
HFCB8-4080(Screw Fixing Type)
40
403
13
4-R3
40
40
133
4-R3.5 80
133
40
4-R2
E�The pin shape and numbers of extrusion caps may be changed to prevent caps from easily falling off.
HFCK8-4040
o_03_41_52
42.5
2.5
13.5 42
.542
.5
4-R2
QFeatures: Standard caps for protecting extrusion end faces. Alterations for Aluminum Extrusions are not necessary. QFeatures: Extrusion End Caps for protecting 3 sides at corners.
QFeatures: Extrusion End Caps only for GFS8-4040 and GFS8-4080. Alterations are required.
QFeatures: Extrusion End Caps Screw Mounting Type. Requires no alteration and excels in safety.
Type MMaterialHFCGFC Polyamide
HFCL Low Density Polyethylene
MMaterial: SUS304
E HFCL is not applicable to extrusions with Wrench Hole in Fixed Position (P.785), D Type Hole (P.790), or L Hole (P.793).
E Due to the properties of its material, when HFCL is mounted onto the mating Aluminum extrusion, some dim. variation may be generated.
E The pin's shape and numbers of extrusion end caps may be changed to prevent caps from easily falling off.
E Some products are not required to specify colors. In that case, color is black.
HFC45A8
38
45°
40
40
6-R2
(47.
46)
HFC30A8
(46.
59)
38
6-R2 40
40
30°
HFC60A8
38
60°
6-R2
(46.
59)
40
40
HFCR8-4040
40
40
83
R32
2-R1 R3
HFC8-8080
80
4-R180
113
GFC8-4040HFC8-808040
80
80
40
40
6-R3
103
HFC8-4040
HFC8-4012040
A A
120
15.5
3 Cross Section A-A
4-R3
EHFC and HFCL can be used for each Aluminum Extrusion other than GFS/GNFS Series. EFor GFS Series Aluminum Extrusions, select GFC or HFCD ( W P.704).EOnly for GFC, 4 tabs are fitted into the mating extrusion slot upon assembly.
HFC8-4080
40
4-R280
83
40
A A
40
1111 3
4-R3
Cross Section A-A
HFCL8-4040
40
A A
40
3 12 194-R3
Cross Section A-A
HFCL8-408040
A A
8019
3
4-R3
Cross Section A-A
40
A A
40113
4-R3
Cross Section A-A
* For Aluminum Extrusion EFS Series, the same extrusion end caps as of HFS Series can be used.
Part Number Color Accessory Applicable Extrusion *
Unit Price Volume Discount Rate1 ~ 14 pc(s). 15~19 20~200
HFCK8-4040 B(Black) HFBMB5-15 8-4040
* For Aluminum Extrusion EFS Series, the same extrusion end caps as of HFS Series can be used.EFlat Head Screw is included for Screw Mount Type. (Black: HFBMB5-15, Light Gray, Yellow: SHFBS5-15)
Part NumberColor
Unit Price Volume Discount Rate Applicable Extrusion *Type No. 1 ~ 14 pc(s). 15~19 20~500
HFCB84040 B (Black)
S (Light Gray)Y (Yellow)
E�Yellow Type is available for 4040 only.
8-4040
4080 8-4080
Part NumberApplicable Screw Applicable Extrusion
Unit Price Volume Discount Rate
Type No. 1 ~ 9 pc(s). 10~50
HFCD84040 SHFBS12-20
(Not included)GFS8-4040
4080 GFS8-4080
Part Number
HFCK8-4040-B
Part Number
HFCB8-4040-S
Part Number
HFCD8-4040
ETapping on extrusion is not required.
<After Mounting>
HFCB8-4040-B
<Before Mounting>
HFCK8-4040-B<Before Mounting>
<After Mounting>
ETapping on extrusion is not required.
80
40
4-R3
2-M12 Countersink
2
4040
40
4-R3
M12 Countersink
2
HFCD8-4040 HFCD8-408080
40
4-R3
2-M12 Countersink
2
4040
40
4-R3
M12 Countersink
2 E Special alteration is required on cross sections of extrusions to mount extrusion end caps. (P.794)
(E1) Not applicable to EFSH8-4040. (E2) This extrusion end cap can be used for each GFS Series or other type Aluminum Extrusion having the same shape.
Part NumberColor
Unit Price Volume Discount RateApplicable Extrusion
Type No. 1 ~ 14 pc(s). 15~19 20~200
HFC8
4040
B(Black)
S(Light Gray)
8-4040(E1)4080 8-408040120 8-401208080 8-8080
808040 8-808040
HFCL84040 8-40404080 8-4080
HFC30A8 30A8-40HFC45A8 45A8-40HFC60A8 60A8-40HFCR8-4040 8-4040GFC8 B GFS8-4040(E2)
Part Number - Color
HFC30A8 - B
When using Aluminum Extrusion HFS8-80160, please use 2 pieces of HFC8-8080.
4040
Recommended
