AX 01The new GenerationAAXX 0011 PPllaattee BBeeaarriinngg
TTeesstteerreelleeccttrroonniicc eevvaalluuaattiioonn ·· mmiinnii
pprriinntteerr ·· ccoommppaacctt ddeessiiggnn
For the test, the soil is loaded and unlo-aded in fixed steps
using a circular loa-ding plate and a hydraulic loadingdevice. The
normal stress below theplate and the corresponding deflec-tions of
the plate are recorded andshown in a diagram. The electronicdevice
AX 01 is the simple solution todetermine the strain moduli Ev2
andEv1 (a figure for the bearing capacity)and the ratio Ev2/Ev1 (a
figure for thecompaction level).
The results of the test are evaluatedimmediately, shown at the
display, andprinted with the built-in thermo printerat the
road-works. It is usable evenunder bad environmental conditions
–e.g. in rain – because of the rain pro-ofed case, a illuminated
display andbuttons at the outside. The test results– stored at the
smart card – can be usedwith Microsoft Excel.
The unrivalled AX01 feature is itsoutstanding and stainless
pro-duct design. It is equipped withruggedised and rain
proofedindustrial sensors to achieve pre-cision test results.
Due to the compact design of thetest tripod the device fits in
thecar boot.
The dimensions are:LxWxH 1150 mm x 340 x 260 mm
Meitzendorf, Hintern Hecken 1 · 39179 Barleben · Germany · Tel.
+ 49 (0)3 92 02 87 92 52 · Fax + 49 (0)3 92 02 87 92 57 ·
[email protected]
compact design for comfortable trans-portation
Technical specifications: Subject to change without noticeMay,
2006
EElleeccttrroonniicc ddeevviiccee::- case made from PET, the
transparent top cover with scratch-resistant surface- thermo
printer with 57 mm print width- 1 smart card for the storage of
approximately 200 tests- plate diameters are adjustable: 300 mm,
600 mm, 762 mm- lever ratio is adjustable in the range 1:1 to 1:2-
precision (resolution):
deflection 0,01 mmnormal stress 0,0001 MN/m2 (printed and
stored)0,001 MN/m2 (displayed)
- rechargeable battery, 9.6 volts, 5Ah, fast charger 2h, for
about 48 h of non-stop use
- weight about 4.5 kg
TTeesstt ttrriippoodd::- direct measurement of the deflection
according to DIN 18134
(displacement test with one sensor only)- test arm
extractable/fold-out-able- round foots for optimal placement at
rough and/or soft surfaces- short (250 mm) and long (500 mm)
fixture for the displacement sensor- displacement sensor is made
from stainless steel, stroke of the sensor: 15 mm- dimensions:
folded L x B x H 1150 x 340 x 260 mm
unfolded L x B x H 2330 x 340 x 310 mm- distance (mid of loading
plate – axis of front foots): 1500 mm- weight: 13.9kg
LLooaaddiinngg aappppaarraattuuss::- hydraulic jack assembly
with jack for 100kN force, manual hydraulic pump and
2 m high pressure hose- bearing plate made from steel S355JO,
stainless surface,
diameter 300 mm, tunnel for the displacement sensor- force
sensor 100kN made from stainless steel- extension set (2 x 25 mm, 2
x 50 mm, 2 x 100 mm, 2 x 150 mm,
complete height 650 mm, complete weight 3.1 kg)- upper magnetic
ball joint (loadable up to 60kN, weight 0.9 kg)
DDiimmeennssiioonnss::- height of the hydraulic jack
(retracted): 285 mm, stroke 150 mm- weight of the hydraulic jack
assembly (jack + pump + hose): 9.5 kg- bearing plate with force
sensor mounted: diameter 300 mm, height 265mm,
weight: 22.6 kg
- weight complete: (without packaging, without transport box):
54.9 kg
Anix GmbHELECTRONIC PRECISION INSTRUMENTS
Anix GmbHELECTRONIC PRECISION INSTRUMENTS
