SAMPLEDESCRIPTIONAPPLICATION1) Continuous thickVisible outlines2)Continuous thinImaginary, dimension, projection linesLeader lines, Hatching lines.3)Dotted thin / thickHidden outlines, hidden eges4)Chain thin Centre lines, lines of symmetry5)Chain thin double-dottedOutlines of adjecent parts,Initial outline of part before forming6)Continuous thinLong break lines(with zigzag)TYPES OF LINE
DIMENSION SYMBOLLinearAlignedRadiusDiameterAngularLeaderABArc Length(AB)Reference Dim.Approximate Dim.AB Aprox.62.57-10Dim. With ToleranceAA
STRAIGHTNESSFLATNESSCIRCULARITY CYLINDRICITYPERPENDICULARITY MACHINING SYMBOL0.080.080.10.10.1COAXIALITY
SURFACE FINISH SYMBOLS
DRAWING PROJECTION METHODS
Sheet1
VERTICAL PLANE
FOURTH
QUADRANT
FIRST
4th ANGLEQUADRANT
1st ANGLE
HORIZONTAL PLANE
THIRD
QUADRANT
3rd ANGLELOOKING DIRECTION
SECOND
QUADRANT
2nd ANGLE
1st ANGLE
ELEVATIONAXIS
R.H.S.VIEWPLANL.H.S.VIEW
3rd ANGLE
L.H.S.VIEWPLANR.H.S.VIEW
ELEVATIONAXIS
Sheet2
TYPES OF LINES
SAMPLEDESCRIPTIONAPPLICATION
1)Continuous thickVisible outlines
2)Continuous thinImaginary, dimension, projection lines
Leader lines, Hatching lines.
3)Dotted thin / thickHidden outlines, hidden eges
4)Chain thinCentre lines, lines of symmetry
5)Chain thin double-dottedOutlines of adjecent parts,
Initial outline of part before forming
6)Continuous thinLong break lines
(with zigzag)
Sheet3
AXISAXIS1st ANGLE3rd ANGLEELEVATIONPLANR.H.S.VIEWL.H.S.VIEWELEVATIONPLANR.H.S.VIEWL.H.S.VIEWDRAWING PROJECTION METHODS(contd.)
VIEWS AND SECTIONS
VIEWS AND SECTIONS(contd.)
GENERAL ASSEMBLY (PRESSURE VESSEL)
TraysToriconeSkirtNozzleTop Dish EndShell SectionLadder cleat
PRB: Pressure Retaining BoundaryPRT : Pressure Retaining T-FrameSTBD : Star Board ( Right Side )PORT : Port ( Left Side )FWD : Forward ( Direction of Motion )AFT : After ( Back of Vessel )NTD : Normative Technical DocumentSOT : Submarine Overseeing TeamCOMMON TERMS USED IN SPECIAL JOBS
Skill Refresher ModuleModule:- Fabrication Drawing Reading & UnderstandingPre - Test / Post Test for ParticipantsTime:- 30 Min(1) To do changes in Drawing the document is used is _________________. (A) DCR(B) NCR(C) QAR(D) QCR(2) M12 X 8nos. Written in the Drawing indicates ________________.(A) External threads of 12 dia. Holes(B) Internal thread M-12X8 deep(C) Chamfer of 12mm(D) Drilled hole 8nos. & M12 threads(3) What indicates symbol in the drawing .(A) Machining after welding(B) Machining before welding(C) Grinding After welding(D) No welding.(4) To show critical details of any part ______________ view is used in Drawing.(A) Sectional View(B) Full View(C) Half View (D) Partial View(5) Non visible part of job is indicated by ______________ Line.(A) (B)(C)(D) Cont.
(6) The surface roughness indicates surface roughness in ____________.(A) M.M.(B) C.M.(C) Meter(D) Microns(7) First Angle projection, plan is placed bottom of ____________.(A) Elevation(B) RT-Side View(C) LT-side View(D) in same plan of elevation(8) What indicates A: __________________(9) What Indicates B: __________________(10) What Indicates C: __________________(11) What is D: __________________Cont.
(12) What Indicates the Sketch (A) Circularity(B) Cylindrycity(C) Co- axiality (D) Non of the above
(13) What indicates the Sketch(A) Perpendicularity(B) Flatness(C) Straightness(D) Non of the above
Cont.
Cont.(14) symbol in the drawing indicates.(A) Seam No.(B) Nozzle Mark(C) Item No.(D) None of the above(15) Distance L is = ______________mm. 100Typ100Typ9 holes @ 200mm equal spaceL(A) 2000mm(B) 2200mm(C) 1800mm(D) 1600mm
Cont.PRACTICAL TEST
(1) Draw First angle orthographic Projection of the Sketch
(2) Make BOM of the Sketch given below
1015200150015006 Nos. 10 mm thk Gusset plates, 3 nos. both sides as shown in the Drg.
150
Pre-Test / Post Test Answer SheetQu.- Ans.1 - A2 - D3 - A4 - A5 - AQu. - Ans.11 - Nozzle / Hole12 - A13 - A14 - B15 - 1800mmPRACTICAL TEST ANS.Qu.- Ans.6 - D7 - A8 - Object Line9 - Non Visible Line10 - Centre Line(1) Orthographic Projection(2) Bill of Material
PART NO
DISCRIPTION
SIZE
QTY
JOB
SP
1
PLATE
1500 x 200 x 10thk
1
2
PLATE
1500 x 150 x 15thk
1
3
PLATE
150 x 92.5 x 10thk
3