eLTE2.3V200R003C00
eLTE2.3 DBS3900 LTE FDD BasicFeature Description
Issue Draft A
Date 2014-02-10
HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Issue Draft A (2014-02-10)Huawei Proprietary and Confidential
Copyright © HuaweiTechnologies Co., Ltd.
i
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description Contents
Contents
1 Basic Features...............................................................................11.1 Standards Compliance....................................................................................................................................................11.1.1 LBFD-001001 3GPP R8 Specifications......................................................................................................................11.1.2 LBFD-001007 3GPP R9 Specifications......................................................................................................................21.1.3 LBFD-001008 3GPP R10 Specifications....................................................................................................................21.1.4 LBFD-001002 FDD mode...........................................................................................................................................31.1.5 LBFD-001003 Scalable Bandwidth............................................................................................................................41.1.6 LBFD-001004 CP length.............................................................................................................................................51.1.6.1 LBFD-00100401 Normal CP...................................................................................................................................51.1.7 LBFD-001005 Modulation: DL/UL QPSK, DL/UL 16QAM, DL 64QAM...............................................................61.1.8 LBFD-001006 AMC....................................................................................................................................................71.2 RAN Architecture & Features........................................................................................................................................81.2.1 LBFD-002001 Logical Channel Management............................................................................................................81.2.2 LBFD-002002 Transport Channel Management.........................................................................................................91.2.3 LBFD-002003 Physical Channel Management.........................................................................................................101.2.4 LBFD-002004 Integrity Protection...........................................................................................................................111.2.5 LBFD-002005 DL Asynchronous HARQ.................................................................................................................121.2.6 LBFD-002006 UL Synchronous HARQ...................................................................................................................131.2.7 LBFD-002007 RRC Connection Management.........................................................................................................141.2.8 LBFD-002008 Radio Bearer Management...............................................................................................................151.2.9 LBFD-002009 Broadcast of system information......................................................................................................161.2.10 LBFD-002010 Random Access Procedure..............................................................................................................171.2.11 LBFD-002011 Paging..............................................................................................................................................181.2.12 LBFD-002012 Cell Access Radius up to 15km......................................................................................................191.2.13 LBFD-002023 Admission Control..........................................................................................................................201.2.14 LBFD-002024 Congestion Control.........................................................................................................................211.2.15 LBFD-002025 Basic Scheduling.............................................................................................................................221.2.16 LBFD-002026 Uplink Power Control.....................................................................................................................231.2.17 LBFD-002016 Dynamic Downlink Power Allocation............................................................................................251.2.18 LBFD-002018 Mobility Management.....................................................................................................................261.2.18.1 LBFD-00201801 Coverage Based Intra-frequency Handover.............................................................................261.2.18.2 LBFD-00201802 Coverage Based Inter-frequency Handover.............................................................................27
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
ii
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description Contents
1.2.18.3 LBFD-00201803 Cell Selection and Re-selection...............................................................................................291.2.18.4 LBFD-00201804 Distance Based Inter-frequency Handover..............................................................................301.2.18.5 LBFD-00201805 Service Based Inter-frequency Handover................................................................................301.2.19 LBFD-002020 Antenna Configuration....................................................................................................................311.2.19.1 LBFD-00202001 UL 2-Antenna Receive Diversity.............................................................................................311.2.20 LBFD-002021 Reliability........................................................................................................................................321.2.20.1 LBFD-00202101 Main Processing and Transport Unit Cold Backup..................................................................321.2.20.2 LBFD-00202102 Cell Re-build Between Baseband Processing Units...............................................................331.2.20.3 LBFD-00202103 SCTP Multi-homing.................................................................................................................341.2.20.4 LBFD-00202104 Intra-baseband Card Resource Pool (user level/cell level)......................................................351.2.21 LBFD-002027 Support of UE Category 1...............................................................................................................361.2.22 LBFD-002031 Support of aperiodic CQI reports....................................................................................................381.2.23 LBFD-002032 Extended-QCI.................................................................................................................................391.2.24 LBFD-002033 SCTP Congestion Control...............................................................................................................401.2.25 LBFD-002034 RRU Channel Cross Connection Under MIMO.............................................................................411.2.26 LBFD-070102 MBR>GBR Configuration..............................................................................................................431.3 Transmission & Security..............................................................................................................................................431.3.1 LBFD-003001 Transmission Networking.................................................................................................................431.3.1.1 LBFD-00300101 Star Topology.............................................................................................................................431.3.1.2 LBFD-00300102 Chain Topology..........................................................................................................................451.3.1.3 LBFD-00300103 Tree Topology............................................................................................................................461.3.2 LBFD-003002 Basic Qos Management....................................................................................................................471.3.2.1 LBFD-00300201 DiffServ QoS Support................................................................................................................471.3.3 LBFD-003003 VLAN Support (IEEE 802.1p/q)......................................................................................................481.3.4 LBFD-003005 Synchronization................................................................................................................................491.3.4.1 LBFD-00300501 Clock Source Switching Manually or Automatically................................................................491.3.4.2 LBFD-00300502 Free-running Mode....................................................................................................................501.3.4.3 LBFD-00300503 Synchronization with GPS.........................................................................................................511.3.4.4 LBFD-00300504 Synchronization with BITS........................................................................................................521.3.4.5 LBFD-00300505 Synchronization with 1PPS........................................................................................................531.3.5 LBFD-003006 IPv4/IPv6 Dual Stack........................................................................................................................531.4 Operation & Maintenance............................................................................................................................................541.4.1 LBFD-004001 Local Maintenance of the LMT........................................................................................................541.4.2 LBFD-004002 Centralized U2000 Management......................................................................................................551.4.3 LBFD-004003 Security Socket Layer.......................................................................................................................561.4.4 LBFD-004004 Software Version Upgrade Management..........................................................................................571.4.5 LBFD-004005 Hot Patch Management.....................................................................................................................581.4.6 LBFD-004006 Fault Management............................................................................................................................591.4.7 LBFD-004007 Configuration Management..............................................................................................................601.4.8 LBFD-004008 Performance Management................................................................................................................611.4.9 LBFD-004009 Real-time Monitoring of System Running Information....................................................................631.4.10 LBFD-004010 Security Management.....................................................................................................................64
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
iii
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description Contents
1.4.11 LBFD-004011 Optimized eNodeB Commissioning Solution.................................................................................641.4.12 LBFD-004012 Environment Monitoring................................................................................................................651.4.13 LBFD-004013 Inventory Management...................................................................................................................661.4.14 LBFD-004014 License Management......................................................................................................................671.4.15 LBFD-004015 License Control for Urgency...........................................................................................................68
2 Acronyms and Abbreviations........................................................70
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
iv
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description Figures
Figures
Figure 1-1 3*10M 2T2R.......................................................................................................................................34
Figure 1-2 Stream Control Transmission Protocol...............................................................................................35
Figure 1-3 RRU channel cross connection under MIMO.....................................................................................42
Figure 1-4 Comparing with no MIMO load Sharing............................................................................................42
Figure 1-5 Star topology.......................................................................................................................................44
Figure 1-6 Chain topology....................................................................................................................................45
Figure 1-7 Tree topology.......................................................................................................................................46
Figure 1-8 License file management.....................................................................................................................68
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
v
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description Tables
Tables
Table 1-1 Preamble formats and cell access radius...............................................................................................19
Table 1-2 Downlink physical layer parameter values set by the field UE-Category............................................37
Table 1-3 Uplink physical layer parameter values set by the field UE-Category.................................................37
Table 1-4 Total layer 2 buffer sizes set by the field UE-Category........................................................................37
Table 1-5 Relationship between QCI and DSCP...................................................................................................48
Table 2-1 Acronyms and Abbreviations................................................................................................................70
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
vi
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1 Basic Features
About This Chapter1.1 Standards Compliance
1.2 RAN Architecture & Features
1.3 Transmission & Security
1.4 Operation & Maintenance
1.1 Standards Compliance1.1.1 LBFD-001001 3GPP R8 SpecificationsAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei LTE eNodeB is compliant with 3GPP Release 8 specifications 2009Q3.
BenefitsNone
DescriptionHuawei LTE eNodeB is compliant with 3GPP Release 8 specifications 2009Q3.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
1
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Huawei is an active participant and great contributor to 3GPP specification development. This high-level involvement enables Huawei to actively contribute, and closely follow 3GPP standard development during Huawei product development. LTE eNodeB supports 3GPP Release 8 2009Q3.
EnhancementNone
DependencyNone
1.1.2 LBFD-001007 3GPP R9 SpecificationsAvailability
This feature is
applicable to Macro from eRAN2.1 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei LTE eNodeB is compliant with 3GPP Release 9 specifications 2010.09 version.
BenefitsNone
DescriptionHuawei LTE eNodeB is compliant with 3GPP Release 9 specifications 2010.09 version.
Huawei is an active participant and great contributor to 3GPP specification development. This high-level involvement enables Huawei to actively contribute, and closely follow 3GPP standard development during Huawei product development. LTE eNodeB supports 3GPP Release 9 specifications 2010.09 version, which is the latest version of LTE standard.
EnhancementNone
DependencyNone
1.1.3 LBFD-001008 3GPP R10 SpecificationsAvailability
This feature is
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
2
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
applicable to Macro from eRAN3.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei LTE eNodeB is compliant with 3GPP Release 10 specifications.
BenefitsNone
DescriptionHuawei LTE eNodeB is compliant with 3GPP Release 10 specifications 2011.03 version.
Huawei is an active participant and great contributor to 3GPP specification development. This high-level involvement enables Huawei to actively contribute, and closely follow 3GPP standard development during Huawei product development. LTE eNodeB supports 3GPP Release 10 specifications 2011.03 version.
EnhancementNone
DependencyNone
1.1.4 LBFD-001002 FDD modeAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei LTE supports the Frequency Division Duplex (FDD) mode .
BenefitsNone
DescriptionThe 3GPP specifications support the FDD mode. In FDD mode, separate frequency bands are used for the uplink and the downlink.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
3
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
EnhancementNone
Dependency Others
The related network elements (NEs) should support FDD mode.
1.1.5 LBFD-001003 Scalable BandwidthAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei LTE eRAN1.0 supports the bandwidths of 5 MHz, 10 MHz, 15 MHz, and 20 MHz.
Huawei LTE eRAN2.0 supports two new bandwidths of 1.4 MHz and 3 MHz to extend the range of bandwidth support for the LTE technology. Micro eNodeB does not support 1.4 MHz and 3 MHz bandwidth.
Benefits Larger bandwidth produces higher throughput and better user experience. Flexible bandwidth configuration helps operators use frequency bands. Besides the existing bandwidths supported by eRAN1.0, the introduction of 1.4 MHz
and 3 MHz bandwidths enables the flexibility for operators to allocate smaller bandwidth less than 5 MHz, thus saving radio resources. This is not applicable to Micro eNodeB.
DescriptionHuawei LTE eRAN2.0 supports the channel bandwidths from 1.4 MHz to 20 MHz, including 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, and 20 MHz. The bandwidth can be configured by the software.
Enhancement In eRAN2.0
Huawei LTE eRAN1.0 supports the bandwidths of 5 MHz, 10 MHz, 15 MHz, and 20 MHz.Huawei LTE eRAN2.0 supports two new bandwidths of 1.4 MHz and 3 MHz.
Dependency UE
UEs should support the same bandwidth as the eNodeB.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
4
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.1.6 LBFD-001004 CP length1.1.6.1 LBFD-00100401 Normal CP
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryIn an OFDM symbol, the Cyclic Prefix (CP) is a time-domain replication of the end of the symbol and is appended to the beginning of the symbol. It provides the guard interval in the OFDM to decrease the inter-symbol interference due to the multipath delay.
BenefitsThe CP is used to decrease the inter-symbol interference due to the multipath delay.
DescriptionThe CP is the guard interval used in the OFDM to decrease the interference due to the multipath delay.
There are two CP lengths defined in 3GPP specifications: normal CP and extended CP.
In the case of 15 kHz subcarrier spacing, the normal CP corresponds to seven OFDM symbols per slot in the downlink and seven SC-FDMA symbols per slot in the uplink. The normal CP length (time) is calculated as follows:
In the downlink
Normal CP: TCP = 160 x Ts (OFDM symbol #0), TCP = 144 x Ts (OFDM symbol #1 to #6)
In the uplink
Normal CP: TCP = 160 x Ts (SC-FDMA symbol #0), TCP = 144 x Ts (SC-FDMA symbol #1 to #6)
Where, Ts = 1 / (2048 x Df), Df = 15 kHz
EnhancementNone
DependencyNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
5
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.1.7 LBFD-001005 Modulation: DL/UL QPSK, DL/UL 16QAM, DL 64QAMAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature shows the different modulation schemes supported by the UE and eNodeB.
BenefitsThis feature provides a wide range of modulation schemes to be chosen based on the channel condition. Higher-order modulation schemes, such as DL 64QAM, can be used under excellent channel conditions to achieve higher data rates, which improves the system throughput and spectrum efficiency.
DescriptionThis feature provides a wide range of modulation schemes that can be used by both the eNodeB and the UE in uplink and downlink.
The following modulation schemes are supported:
Uplink/downlink Quadrature Phase Shift Keying (QPSK) Uplink/downlink 16 Quadrature Amplitude Modulation (16QAM) Downlink 64QAM
The characteristics are as follows:
QPSK allows up to two information bits modulated per symbol due to four different neighboring alternatives.
16QAM allows up to four information bits modulated per symbol due to 16 different neighboring alternatives.
64QAM allows up to six information bits modulated per symbol due to 64 different neighboring alternatives.
This feature allows the eNodeB and UE to choose an optimal modulation scheme based on the current channel condition to achieve the best tradeoff between the user data rate and the frame error rate (FER) during transmission.
A more favorable channel condition is required to support a higher-order modulation scheme.
For example, when a UE is in a poor radio environment, it may use a low-order QPSK modulation scheme for uplink transmission to meet the requirement of the call quality. When a UE is in an excellent radio environment, it can use a high-order QAM modulation (such as 16QAM) scheme for uplink transmission to achieve high bit rates.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
6
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
EnhancementNone
Dependency UE
The UE should support the same modulation scheme.
1.1.8 LBFD-001006 AMCAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe Adaptive Modulation and Coding (AMC) function allows an eNodeB to adaptively select the optimal Modulation and Coding Scheme (MCS) according to the channel condition. This improves the spectrum efficiency after the system resource and transmitting power are fixed. Therefore, the throughput can be maximized and the Quality of Service (QoS) requirements can be met.
BenefitsThe AMC provides the following benefits:
Maximizes the system throughput by selecting the optimal MCS. Meets the QoS requirement (such as the packet loss rate) by selecting the optimal MCS
to achieve the best tradeoff between data rate and block error rate.
DescriptionThe AMC function allows an eNodeB to adaptively select the optimal MCS according to the channel information. This improves the spectrum efficiency after the system resource and transmitting power are fixed. Therefore, the throughput can be maximized and the QoS requirements can be met.
In the uplink, the initial MCS can be selected on the basis of the Signal to Interference plus Noise Ratio (SINR) of the uplink Reference Signal (RS) measured by the eNodeB. It can also be adjusted on the basis of whether the uplink transmission involves control signals. Note that control signals might require a lower-order MCS for ensuring a reliable transmission.
In the downlink, the eNodeB first selects the MCS for each UE based on the CQI reported from the UE and assigned power for the UE. Then, the eNodeB can adjust the CQI to impact MCS based on the BLER, in order to maximize the usage of the radio resources.
EnhancementNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
7
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
DependencyNone
1.2 RAN Architecture & Features1.2.1 LBFD-002001 Logical Channel ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe logical channels are provided between the Medium Access Control (MAC) layer and the Radio Link Control (RLC) layer. Each logical channel type is defined according to the type of the transmitted data. They are generally classified into two types: control channels and traffic channels.
In Huawei LTE eNodeB, all logical channels are supported except those related to the evolved Multimedia Broadcast Multicast Service (eMBMS) functionality.
BenefitsThe logical channels are responsible for what type of information is transferred.
DescriptionThe logical channels are provided between the MAC layer and the RLC layer. They are responsible for "what is transported". They are generally classified into two types:
Control channels: for transmitting the control plane information Traffic channels: for transmitting the user plane information
Control channels include:
Broadcast Control Channel (BCCH) Paging Control Channel (PCCH) Common Control Channel (CCCH) Multicast Control Channel (MCCH) Dedicated Control Channel (DCCH)
Traffic channels include:
Dedicated Traffic Channel (DTCH) Multicast Traffic Channel (MTCH)
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
8
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
In Huawei LTE eNodeB, all logical channels are supported except those related to the eMBMS functionality, such as MCCH and MTCH.
EnhancementNone
DependencyNone
1.2.2 LBFD-002002 Transport Channel ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryTransport channels that are provided between the MAC layer and the physical layer, are defined according to the type of transmitted data and the method of data transmission over the radio interface. They are used to offer the information about transmission services for the MAC and higher layers. In Huawei LTE eNodeB, all transport channels except those related to the eMBMS functionality are supported.
BenefitsThe transport channels are responsible for what type of data is transmitted and how the data is transmitted.
DescriptionThe transport channels are provided between the MAC layer and the physical layer. They are responsible for what type of data is transmitted and how the data is transmitted over the radio interface.
Downlink transport channels are classified into the following types:
Broadcast Channel (BCH) Downlink Shared Channel (DL-SCH) Paging Channel (PCH) Multicast Channel (MCH)
Uplink transport channels are classified into the following types:
Uplink Shared Channel (UL-SCH) Random Access Channel (RACH)
In Huawei LTE eNodeB, all transport channels are supported except those related to the eMBMS functionality, such as MCH.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
9
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
EnhancementNone
DependencyNone
1.2.3 LBFD-002003 Physical Channel ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe physical layer is responsible for coding, physical-layer hybrid-ARQ processing, modulation, multi-antenna processing, and mapping from the signal to the appropriate physical time-frequency resources. Based on the mapping, a transport channel at the higher layer can serve one or several physical channels at the physical layer.
In Huawei LTE eNodeB, all physical channels are supported except those related to the eMBMS functionality, such as PMCH.
BenefitsEach physical channel provides a set of resource blocks for information transmission.
DescriptionEach physical channel corresponds to a set of resource blocks carrying the information from higher layers.
Downlink physical channels are classified into the following types:
Physical Broadcast Channel (PBCH) Physical Control Format Indicator Channel (PCFICH) Physical Downlink Control Channel (PDCCH) Physical Hybrid ARQ Indicator Channel (PHICH) Physical Downlink Shared Channel (PDSCH) Physical Multicast Channel (PMCH)
Uplink physical channels are classified into the following types:
Physical Uplink Control Channel (PUCCH) Physical Uplink Shared Channel (PUSCH) Physical Random Access Channel (PRACH)
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
10
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
In Huawei LTE eNodeB, all physical channels are supported except those related to the eMBMS functionality, such as PMCH.
EnhancementNone
DependencyNone
1.2.4 LBFD-002004 Integrity ProtectionAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe feature offers the integrity protection for signaling data. It enables the receiving entity (either UE or eNodeB) to check whether the signaling data has been illegally modified. It encrypts or decrypts the signaling data by using a certain integrity algorithm through an RRC message.
BenefitsThe integrity protection procedure prevents the signaling data from illegal modification.
DescriptionLTE offers the integrity protection for RRC signaling messages at the PDCP layer. The sender calculates a message authentication code MAC-I based on the RRC message and some parameters (such as the key, bearer ID, direction, and count) by using an integrity algorithm, and then send the code to the receiver together with the message. The receiver recalculates the code and compares it with the code in the message. If the two codes are inconsistent, the receiver knows that the message has been modified illegally.
The eNodeB decides which integrity algorithm to use and informs each UE of it through an RRC message.
Enhancement In eRAN2.0
In addition to the AES, Huawei eRAN2.0 also supports integrity algorithm SNOW3G. In eRAN6.0
Macro also supports intergrity algorithm ZUC. In eRAN7.0
Micro also supports integrity algorithm ZUC.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
11
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Dependency UE
The UE should support the same integrity algorithm as the eNodeB.
1.2.5 LBFD-002005 DL Asynchronous HARQAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe Hybrid Automatic Repeat Request (HARQ) provides robustness against transmission errors. It is also a mechanism for capacity enhancement. As HARQ retransmissions are fast, many services allow one or multiple times of retransmissions, thereby forming an implicit (closed loop) rate-control mechanism. An asynchronous protocol is the basis for downlink HARQ operation. Hence, downlink retransmissions may occur at any time after the initial transmission, and an explicit HARQ process number is used to indicate the HARQ process.
BenefitsDL HARQ functionality is a fast retransmission protocol to ensure successful data transmission from the eNodeB to a UE at the physical layer and MAC layer. A UE can request for retransmissions of data that was incorrectly decoded through an NACK message and soft-combine the retransmitted data with the previously received data to improve the decoding performance.
This feature helps improve user throughput and reduce transmission latency in the downlink.
DescriptionThe HARQ is a link enhancement technique combining Forward Error Correction (FEC) and ARQ technologies. Compared with the ARQ, the HARQ can provide faster and more efficient retransmissions with lower transmission latency. In the downlink, if the data received by the UE is decoded correctly by the FEC and passes the Cyclic Redundancy Check (CRC), the UE will send an ACK message to inform the eNodeB that the data was received correctly. Otherwise, the UE will send a NACK message to the eNodeB to request for data retransmission.
Downlink HARQ is an asynchronous adaptive transmission process, which means that the scheduler of the HARQ transmission is not predetermined to the UE. In addition, the DL HARQ information, such as the location of the allocated resource blocks and MCSs, may be different from that of the previous transmissions.
In LTE specifications, the DL HARQ scheme is based on an Incremental Redundancy (IR) algorithm. After the retransmitted data is received, the HARQ process in the UE will soft-combine the retransmitted data with the previously buffered content and then forward the combined data to the FEC for decoding. The soft-combined data will help increase the probability of successful FEC decoding, thus increasing the data reception success rate.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
12
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
In LTE specifications, multiple downlink HARQ processes are adopted to fully utilize system resources. It greatly improves the system throughput and reduces the latency, but it requires more buffer space and signaling overhead.
EnhancementNone
DependencyNone
1.2.6 LBFD-002006 UL Synchronous HARQAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryCompared with the downlink HARQ, uplink retransmission is based on a synchronization protocol. It occurs at a predefined time after the initial transmission and the number of retransmissions can be implicitly derived.
BenefitsThe UL HARQ functionality is a fast retransmission protocol to ensure successful data transmission from the UE to the eNodeB at the physical layer and MAC layer. An eNodeB can request for retransmissions of data that is incorrectly decoded and soft-combine the retransmitted data with the previously received data to improve the decoding performance.
This feature helps improve the user throughput and reduce transmission latency in the uplink.
DescriptionThe HARQ is a link enhancement technique combining FEC and ARQ technologies. Compared with the ARQ, the HARQ can provide faster and more efficient retransmissions with lower transmission latency. In the uplink, if the data received by the eNodeB is decoded correctly by the FEC and passes the CRC check, the eNodeB will send an ACK message over the PHICH to inform the UE that the data was received correctly. Otherwise, the eNodeB will send an NACK message to the UE to request for data retransmission.
In eRAN1.0, Uplink HARQ is a synchronization non-adaptive transmission process, which means that HARQ transmission blocks are predetermined for transmission and retransmission. In addition, the UL HARQ information, such as the location of the allocated resource blocks and MCSs, is predetermined by the eNodeB.
In eRAN2.0, Huawei supports a synchronous adaptive UL HARQ transmission. While retransmitting, the allocated resource block, coding and modulation scheme may be changed
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
13
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
according to the channel quality. But the retransmission transport block size remains the same as the first transmission.
In LTE specifications, UL HARQ scheme is based on an IR algorithm. After the retransmitted data is received, HARQ process in the eNodeB will soft-combine the retransmitted data with the previously buffered content and forward the combined data to the FEC for decoding. The soft-combined data will help increase the probability of successful FEC decoding, thus increasing the data reception success rate.
In LTE specifications, multiple uplink HARQ processes are adopted to fully utilize system resources. It greatly improves the system throughput and reduces the latency, but it requires more buffer space and signaling overhead.
Enhancement In eRAN2.0
Huawei supports a synchronous adaptive UL HARQ transmission. While in eRAN1.0, Uplink HARQ is a synchronization non-adaptive transmission process.
DependencyNone
1.2.7 LBFD-002007 RRC Connection ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryRRC connection is the layer 3 connection between the UE and eNodeB. The RRC connection management aims to manage the layer 3 connection, including establishment, maintenance, and release of the connection.
BenefitsThe RRC connection management is essential from the UE to E-UTRAN, and serves all service procedures and NAS procedures.
DescriptionRRC connection management involves RRC connection establishment, RRC connection reconfiguration, RRC connection re-establishment, and RRC connection release.
RRC connection establishment: This procedure is performed to establish an RRC connection. RRC connection establishment involves Signaling Radio Bearer 1 (SRB1) establishment. The procedure is also used to transmit the initial NAS dedicated information or messages from the UE to the E-UTRAN.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
14
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
RRC connection reconfiguration: This procedure is performed to modify an RRC connection, for example, to establish, modify, or release radio bearers, to perform handovers, and to configure or modify measurements. As a part of the procedure, NAS dedicated information may be transmitted from the E-UTRAN to the UE.
RRC connection re-establishment: This procedure is performed to re-establish an RRC connection after a handover failure or radio link failure. RRC connection re-establishment involves the restoration of SRB1 operation and the re-activation of security. A UE in RRC_CONNECTED mode, for which security has been activated, may initiate the procedure in order to continue the RRC connection. The connection re-establishment will succeed only if the cell has a valid UE context.
RRC connection release: This procedure is performed to release an RRC connection. RRC connection release involves the release of the established radio bearers and the release of all radio resources.
EnhancementNone
DependencyNone
1.2.8 LBFD-002008 Radio Bearer ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryRadio bearer management aims to manage SRB2 and Data Radio Bearer (DRB). The radio bearer management includes the establishment, maintenance, and release of radio bearers.
BenefitsThis feature provides configuration function of radio resources.
DescriptionRadio bearer management involves the establishment, maintenance, and release of radio bearers, as well as the configuration of associated radio resources, for example PDCP, RLC, logical channel, DRX,CQI, power headroom report (PHR), and physical layer configuration. The radio bearer management is implemented during the RRC connection reconfiguration procedure.
EnhancementNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
15
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
DependencyNone
1.2.9 LBFD-002009 Broadcast of system informationAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummarySystem information (SI) includes:
Basic information for a UE to access the E-UTRAN, such as basic radio and channel parameters
Information about cell selection and reselection parameters used by the UE in RRC_IDLE mode
Information about neighboring cells Important messages that should be send to each UE, such as earthquake warning
information
The SI broadcasted over the BCCH can be read without setting an RRC connection, and it can be read by the UE in RRC_IDLE mode and RRC_CONNECTED mode. SI may also be provided to the UE by means of dedicated signaling, for example, in the case of handover.
BenefitsThis feature is the basis for the UE to access the E-UTRAN.
DescriptionSI is classified into the MasterInformationBlock (MIB) and a number of SystemInformationBlocks (SIBs):
MasterInformationBlock defines the information about the most essential physical layers of the cell required for receiving further system information;
SystemInformationBlockType1 contains the information for checking whether a UE is allowed to access a cell and for defining the scheduling of other system information blocks;
SystemInformationBlockType2 contains the information about common and shared channels;
SystemInformationBlockType3 contains cell re-selection information, mainly related to the serving cell;
SystemInformationBlockType4 contains the information about the serving frequency and intra-frequency neighboring cells related to cell re-selection (including common cell re-selection parameters for a frequency and cell-specific re-selection parameters);
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
16
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
SystemInformationBlockType5 contains the information about other E-UTRA frequencies and inter-frequency neighboring cells related to cell re-selection (including common cell re-selection parameters for a frequency and cell-specific re-selection parameters);
SystemInformationBlockType6 contains the information about UTRA frequencies and UTRA neighboring cells related to cell re-selection (including common cell re-selection parameters for a frequency and cell-specific re-selection parameters);
SystemInformationBlockType7 contains the information about GERAN frequencies related to cell re-selection (including cell re-selection parameters for each frequency);
SystemInformationBlockType8 contains the information about CDMA2000 frequencies and CDMA2000 neighboring cells related to cell re-selection (including common cell re-selection parameters for a frequency and cell-specific re-selection parameters);
SystemInformationBlockType9 contains a home eNodeB identifier (HNBID); SystemInformationBlockType10 contains an ETWS primary notification; SystemInformationBlockType11 contains an ETWS secondary notification.
The paging message is used to inform the UEs in RRC_IDLE and the UEs in RRC_CONNECTED of the change of the system information.
Huawei eNodeB supports MIB, SIB1, SIB2, SIB3, SIB4, SIB5, SIB6, SIB7, SIB8, SIB10 and SIB11.
EnhancementNone
DependencyNone
1.2.10 LBFD-002010 Random Access ProcedureAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryRandom access is the essential function of LTE system, which allows a UE to achieve the uplink synchronization and to request for a connection setup. It is performed for the following five events:
Initial access from RRC_IDLE RRC Connection Re-establishment procedure Handover DL data arrival during RRC_CONNECTED and UE is out-of-sync with eNodeB in
uplink
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
17
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
UL data arrival during RRC_CONNECTED and UE is out-of-sync with eNodeB in uplink
BenefitsThis feature is the basis for the UE to access the E-UTRAN.
DescriptionThe random access procedure enables the UE to establish uplink timing synchronization and to request for setup of a connection to an eNodeB.
The procedure can be either contention-based (applicable to all the preceding five events) or non-contention-based (applicable to only handover and DL data arrival). Normal DL/UL transmission may occur after the random access procedure.
Huawei eNodeB supports the two types of random access procedures. In addition, Huawei eNodeB supports random access preamble formats 0–3 and PRACH configurations 0–63 (TS 36.211).
EnhancementNone
DependencyNone
1.2.11 LBFD-002011 PagingAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe purpose of paging is to transmit paging information to a UE in RRC_IDLE mode, and/or to inform UEs in RRC_IDLE and UEs in RRC_CONNECTED mode of a system information change.
BenefitsThis feature is used to page a UE or inform UEs of system information change.
DescriptionE-UTRAN initiates the paging procedure by transmitting the paging message, which can be sent by the MME or eNodeB.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
18
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
When an eNodeB receives a paging message from an MME over the S1 interface, the eNodeB shall perform paging of the UE in cells which belong to tracking areas indicated in the "List of TAIs" Information Element (IE) in the paging message.
When the system information changes, the eNodeB should inform all UEs in the cell through paging, and should guarantee that every UE can receive the paging message, that is, the eNodeB should send the paging message on each possible paging occasion throughout a DRX cycle. Support for UE discontinuous reception must be broadcasted to the entire cell coverage area and mapped to physical resources.
EnhancementNone
DependencyNone
1.2.12 LBFD-002012 Cell Access Radius up to 15kmAvailability
This feature is
applicable to Macro from eRAN1.0 not applicable to Micro not applicable to Lampsite
SummaryTo improve wireless network coverage, 3GPP TS 36.211 has defined four types of preamble formats (0, 1, 2, 3) for frame structure type 1, among which the basic format 0 corresponds to 15 km of cell access radius.
BenefitsThis feature is used in small cell scenarios.
DescriptionThis feature provides operator with support of 15km cell radius. According to 3GPP TS 36.211, four types of preamble format (0, 1, 2, 3) for PRACH are defined to support different values of cell access radius, as shown in Table 1-1.
Table 1-1 Preamble formats and cell access radius
Preamble Format Cell Access Radius
0 About 15 km
1 About 70 km
2 About 30 km
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
19
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
3 About 100 km
For format 0, the supported cell access radius is about 15 km, which is used in small cell scenarios, and considered as basic cell radius. For format 3, the supported cell access radius is about 100 km, which is used in large cell scenarios to enhance the system coverage.
EnhancementNone
DependencyNone
1.2.13 LBFD-002023 Admission ControlAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryAdmission control function ensures the system stability and guarantees the QoS performance by controlling the establishment of the connections within the maximum resource utilization while satisfying the QoS requirements.
BenefitsAdmission control function provides the following benefits:
Reducing the risk of cell instability by controlling the number of admitted calls Achieving an optimal tradeoff between maximizing resource utilization and ensuring
QoS, by avoiding congestion and checking QoS satisfaction
DescriptionAdmission control is a cell-based operation applied to both uplink and downlink. It is one of the key Radio Resource Management (RRM) functions. Admission control is performed when there are new incoming calls or incoming handover attempts. In Huawei admission control solution, system resource limitation and QoS satisfaction ratio are the main considerations for admission control.
When a new incoming call or incoming handover request arrives, admission control is first to check the system resource limitation (including hardware resource usage, and system overload indication). If any of the resources is found to be limited, the new service request will be rejected.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
20
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
If the resource limitation checking passes, for Non-GBR service it will be admitted and for the GBR service it will check the QoS satisfaction ratio The QoS satisfaction ratio is evaluated based on the QoS Class Identifier (QCI). If the QoS satisfaction ratio for the evaluated QoS class is better than a predefined admission threshold, the call request would be accepted; otherwise, it will be rejected.
Note that an incoming handover request has a higher priority than a new incoming call request, because admission control gives a preference to an existing call (handover request) over a new call.
The Allocation/Retention Priority (ARP) can be used to classify Gold, Silver, and Bronze categories with different admission control thresholds. ARP is an attribute of services and is inherited from Evolved Packet Core (EPC).
Enhancement eRAN7.0
In user admission, UE numbers are reserved for privileged UEs to increase the admission success rate of these UEs. Privileged UEs include emergency UEs and high-priority UEs whose cause value of RRC connection establishment request is "highPriorityAccess".
DependencyNone
1.2.14 LBFD-002024 Congestion ControlAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe congestion control feature is used to adjust the system loading when the system is in congestion or the QoS cannot be met.
The main goal of congestion control feature is to guarantee the QoS for the admitted services while achieving the maximum radio resource utilization.
BenefitsThe congestion control feature provides the following benefits:
Prevent system from being unstable due to overload;
Guarantee QoS satisfaction rate of services in the system by effectively reduce the system loading;
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
21
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
DescriptionThis feature is critical to maintain the system stability and deliver acceptable Quality of Service (QoS) when the system is in congestion.
In eNodeB, congestion control is provided in which a method are introduced:
The method is to release low-priority services to alleviate the overloaded system, where the priority is determined based on the ARP assigned to the service.
EnhancementSize reduction on GBR service is not accepted by most operators and is not recommended according to 3GPP. Function of size reduction on GBR service is removed when cell is in congestion.
DependencyNone
1.2.15 LBFD-002025 Basic SchedulingAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe basic scheduling feature provides three common scheduling algorithms (MAX C/I and RR and PF). The operator can select either algorithm.
BenefitsThis feature provides the flexibility for the operator to select the scheduling algorithm, considering the system capacity and fairness among the users.
DescriptionScheduling algorithm enables the system to decide the resource allocation for each UE during each TTI. This feature provides different scheduling algorithms, considering the tradeoff between system capacity and fairness among the users.
There are three scheduling algorithms provided and the operator can decide which algorithm to take.
MAX C/I Round Robin PF (proportional fair)
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
22
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
With MAX C/I, users are scheduled based on their radio channel quality. The radio channel quality is the only factor to be considered in this algorithm and therefore, the fairness among users cannot be guaranteed.
With Round Robin, users are scheduled on turn and neglects of their radio quality. So all the users have the same chance to get the resource and the fairness among uses is guaranteed. But the system capacity is lowest among three scheduling algorithm.
With PF, users are scheduled according to the value of R/r, where R is the maximum data rate corresponding to the channel quality, and r is the average data rate of the user. The PF scheduler, based on the radio channel quality of an individual user, provides the user with an average throughput proportional to its average channel quality. This algorithm is typically used by a wireless system to achieve a moderate cell capacity while to ensure fairness among users.
Enhancement In eRAN2.0
Round Robin is added in this feature.
DependencyNone
1.2.16 LBFD-002026 Uplink Power ControlAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryUplink power control in LTE system is essential to the control of the eNodeB over the uplink transmitting power of UEs. It also controls the interference to the neighboring cells, to improve the system throughput. Uplink control power applies to Physical Uplink Shared Channel (PUSCH), Physical Uplink Control Channel (PUCCH), Sounding Reference Signal (SRS), and Physical Random Access Channel (PRACH).
BenefitsThe uplink power control can reduce the interference between neighboring cells by carefully controlling the transmitting power of UEs by the eNodeB and therefore, increase the overall throughput in an LTE system. The uplink power control can also ensure the quality, such as the block error rate (BLER), of service applications. In addition, uplink power control can reduce the power consumption of UE
DescriptionUplink power control is one of the most important features for an LTE system. By controlling the UE transmission power carefully, the interference to the neighboring cells can be reduced
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
23
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
and therefore the overall system throughput is improved. The uplink power control includes the mechanisms of PUSCH power control, PUCCH power control, SRS power control, and PRACH power control.
The PUSCH power control includes power adjustment for both Dynamic Scheduling and Semi-persistent scheduling.
For Dynamic Scheduling:
Based on the difference between the estimated transmission power spectrum density (PSD) and PSDTarget, the transmitting power of the PUSCH is periodically adjusted according to the channel environment change. If the estimated PSD is greater than PSDTarget, the eNodeB sends a TPC command, ordering a decrease of the transmitting power. If the estimated PSD is smaller than PSDTarget, the eNodeB sends a TPC command, ordering an increase of the transmitting power.
For Semi-persistent Scheduling:
In Semi-persistent Scheduling, based on the difference between the measured IBLER and IBLERTarget, the transmitting power of the PUSCH is periodically adjusted according to the channel environment change. If the measured IBLER is greater than IBLERTarget, the eNodeB sends a TPC command to the UE, ordering an increase of the transmitting power. If the measured IBLER is smaller than IBLERTarget, the eNodeB sends a TPC command to the UE, ordering a decrease of the transmitting power.
The PUSCH TPCs of multiple VoIP users are sent to the UEs through DCI Format 3/3A. By doing so, signaling overheads over PDCCH are reduced.
For PUCCH power control:
Based on the difference between the measured SINR and SINRTarget, the transmitting power of the PUCCH is periodically adjusted according to the channel environment change. If the measured SINR is greater than SINRTarget, the eNodeB sends a TPC command, ordering a decrease of the transmitting power. If the measured SINR is smaller than SINRTarget, the eNodeB sends a TPC command, ordering an increase of the transmitting power.
The uplink SRS power control also employs the same power control mechanism as the PUSCH power control with identical parameter settings. Note that the initial power is calculated in the same way as PUSCH, except that a power offset configured by RRC is added.
For the PRACH power control, the UE will calculate the transmitting power for the initial Random Access (RA) preamble by estimating the downlink path loss and based on the aforementioned "expected received power from UE at eNodeB" obtained by monitoring the broadcast channel. If the RA preamble attempt fails (e.g. no RA preamble response for the eNodeB), the UE can increase the transmitting power for the next RA preamble attempt according to the settings configured by the RRC layer.
EnhancementNone
DependencyNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
24
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.2.17 LBFD-002016 Dynamic Downlink Power AllocationAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryDynamic Downlink Power Allocation allows an eNodeB to dynamically set the transmitting power at downlink channels to reduce power consumption while maintaining the quality of radio links. It provides flexible power allocation for downlink channels based on the user's channel quality and maintains acceptable quality of the downlink connections.
BenefitsThis feature allows flexible power allocation for downlink channels based on the user's channel quality and maintains acceptable quality of the downlink connections. Therefore, it can improve the edge user throughput and transmission power usage.
DescriptionThe LTE downlink power allocation consists of several parts corresponding to different types of downlink channels, such as Physical Downlink Shared Channel (PDSCH), Physical Downlink Control Channel (PDCCH), Physical HARQ Indicator Channel (PHICH), Physical Broadcast Channel (PBCH), and Physical Control Format Indicator Channel (PCFICH).
A Fixed power setting is performed for the cell-specific reference signal, synchronization signal, PBCH, PCFICH, and channels carrying common information of the cell such as PDCCH and PDSCH; since the transmitting power of those signals and channels are needed to ensure the downlink coverage of the cell.
SINRRS estimation is based on the CQI report. Based on the difference between the estimated SINRRS and SINRTarget, the transmitting power of the PHICH is periodically adjusted according to the path loss and shading. If SINRRS is smaller than SINRTarget, the transmitting power is increased. Otherwise, the transmitting power is decreased.)− In dynamic scheduling, the power of the PDSCH is determined by PA, and the power
is adjusted by updating PA. When the eNodeB receives a reported CQI from the UE, it compares it with that reported in the previous time. If there is a great difference between the two CQI values, the power adjustment is performed, and a process of re-calculating the PA for the UE is started.
− In semi-static scheduling, based on the difference between the measured IBLER of VoIP packets and IBLERTarget, the transmitting power of the PDSCH is periodically adjusted to meet IBLERTarget requirements. If the measured IBLER is smaller than IBLERTarget, the transmitting power is decreased. Otherwise, the transmitting power is increased. The transmit power for the PDCCH is periodically adjusted according to the DTX. If the DTX cannot meet system demand, transmit power is increased.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
25
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Enhancement In eRAN2.0
PDSCH and PDCCH dynamic power control is optimized.
DependencyNone
1.2.18 LBFD-002018 Mobility Management1.2.18.1 LBFD-00201801 Coverage Based Intra-frequency Handover
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHandover functionality is important in any cellular telecommunications network. It is performed to ensure no disruption to services. Handover plays a significant role in LTE system performance since its main purpose is to decrease the communication delay, enlarge the coverage and then enhance the system performance.
Intra-Frequency Handover enables a UE in RRC-CONNECTED mode to be served continuously when it moves across different cells that are operating at the same frequency.
BenefitsThe coverage-based intra-frequency handover feature provides supplementary coverage in intra-frequency LTE systems to prevent call drop, enable seamless coverage and therefore improve the network performance and end user experience.
DescriptionThis feature is one of the fundamental functions of an LTE system. The purpose of handover is to ensure that a UE in RRC-CONNECTED mode is served continuously when it moves. Handover in LTE is characterized by the handover procedure in which the original connection is released before a new connection is set up.
Intra-frequency handover refers to the handover between cells operating at the same frequency band. It can be triggered by coverage or load. In eRAN1.0, the coverage-based intra-frequency handover is supported.
The intra-frequency handover procedure can be divided into three phases: handover measurement, handover decision, and handover execution.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
26
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
E-UTRAN configures the handover-related measurement through the RRC Connection Reconfiguration message. The UE could measure either Reference Signal Received Power (RSRP) or Reference Signal Received Quality (RSRQ) for intra-frequency handover.
Upon receiving a measurement report from the UE, the eNodeB makes a handover decision according to certain triggering criteria. If a handover is required, the handover execution procedure will be invoked and the UE will be handed over from the source eNodeB to the target eNodeB. Huawei eRAN1.0 follows the intra-frequency handover procedures specified in 3GPP TS 36.300.
The following scenarios are considered in the intra-frequency handover:
Handover between two cells configured in the same eNodeB. No external neighbor cell is needed. This scenario is not applicable to Micro eNodeB because Micro eNodeB only supports one cell.
Handover between two cells configured in different eNodeBs with an X2 interface available. In this case, the source eNodeB sends a HANDOVER REQUEST message over the X2 interface.
Handover between two cells configured in different eNodeBs with no X2 interface available. In this case, the source eNodeB sends a HANDOVER REQUIRED message over the S1 interface.
Enhancement In eRAN2.2
Each PLMN id of eNodeB will have its own PLMN list; each PLMN list can contain at most 8 PLMN Identities; PLMN list is used as an access list for serving cell to judge whether UE could handover to target cell in Inter-PLMN handover; Other cell, whose PLMN ids are all different with serving cell PLMN id in which UE is located and at same time are not in its PLMN list, will not be considered as target cell in handover process for this UE.
DependencyNone
1.2.18.2 LBFD-00201802 Coverage Based Inter-frequency Handover
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryInter-Frequency Handover enables a UE in RRC-CONNECTED mode to be served continuously when it moves across different cells that are operating at different frequencies.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
27
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
BenefitsThe coverage-based inter-frequency handover provides supplementary coverage in inter-frequency LTE systems to prevent call drop, enable seamless coverage, and therefore improve the network performance and end user experience.
DescriptionThis feature is one of the fundamental functions for an LTE system. The purpose of inter-frequency handover is to ensure that a UE in RRC-CONNECTED mode is served continuously when it moves across different cells operating at different frequencies.
The inter-frequency handover procedure can be divided into four phases: measurement triggering, handover measurement, handover decision, and handover execution.
In inter-frequency handover, neighboring cell measurements are inter-frequency measurements. The measurement is gap assisted for UEs with one RF receiver. The measurement is triggered by an event A2 and stopped by an event A1, based on the monitoring on the value of RSRP or RSRQ.
In inter-frequency handover, the UE sends measurement reports to the eNodeB when the RSRP or RSRQ meets the criteria set in the measurement configuration.
Upon receiving a measurement report from the UE, the eNodeB makes a handover decision. If the measurement meets the handover criteria, the eNodeB will perform the corresponding inter-frequency handover as specified in TS 36.300.
The following inter-frequency handover scenarios are applicable:
Handover between two cells configured in the same eNodeB. In this case, the UE performs the handover between two cells configured in the same eNodeB and no external interface is required. This scenario is not applicable to Micro eNodeB because Micro eNodeB only supports one cell.
Handover between two cells configured in different eNodeBs with an X2 interface available. In this case, the source eNodeB sends a HANDOVER REQUEST message over the X2 interface.
Handover between two cells configured in different eNodeBs with no X2 interface available. In this case, the source eNodeB sends a HANDOVER REQUIRED message over the S1 interface.
Enhancement eRAN2.2
Each PLMN id of eNodeB will have its own PLMN list; each PLMN list can contain at most 8 PLMN Identities; PLMN list is used as an access list for serving cell to judge whether UE could handover to target cell in Inter-PLMN handover; Other cell, whose PLMN ids are all different with serving cell PLMN id in which UE is located and at same time are not in its PLMN list, will not be considered as target cell in handover process for this UE.
eRAN3.0The inter-frequency handover based on UL power is supported. It guarantees service continuity in uplink limited power when a UE moves to the cell edge.
eRAN6.0The urgent redirection function has been provided by this feature. After a UE accesses a cell, the eNodeB delivers two sets of event A2 configurations. One is used for triggering
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
28
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
measurements, and the other is used for triggering urgent redirection. The triggering of event A2 for urgent redirection indicates that the signal quality in the serving cell has become too poor to provide services for the UE. In this case, the eNodeB blindly redirects the UE to a neighboring GERAN, UTRAN, or E-UTRAN cell.
DependencyNone
1.2.18.3 LBFD-00201803 Cell Selection and Re-selection
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryCell selection/reselection is a mechanism for UE in idle mode to select/reselect a cell to camp on and to receive the most appropriate service support upon session activation in LTE systems.
BenefitsThis feature provides a mechanism for UE in idle mode to select/reselect a cell to camp on by supplementary coverage in LTE systems.
This feature facilitates the automatic selection of the network for UE in idle mode and avoids the complexity of manual operations.
The UE is always bound to a relatively good cell to obtain better service quality.
DescriptionWhen UE selects a PLMN or transition from RRC-CONNECTED to RRC-IDLE, cell selection is required. The Non-Access Stratum (NAS) can determine the RAT(s) in which the cell selection should be performed, for instance, by indicating the RAT(s) associated with the selected PLMN and by maintaining a list of forbidden registration areas and a list of equivalent PLMN. The UE shall select a suitable cell based on idle mode measurements and cell selection criteria.
UE in RRC_IDLE can perform cell reselection if UE find a cell with a better radio environment. When camping on a cell, UE shall regularly search for a better cell according to the cell reselection criteria. If a better cell is found, that cell is reselected.
Absolute priorities of different E-UTRAN frequencies can be provided to the UE in the system information and optionally in the RRC message releasing the RRC connection.
Compared with Macro eNodeBs, higher priorities will be set for frequencies of Micro eNodeBs so that the UE prefers to camp on Micro eNodeB cells.
In case a Micro cell is on the same frequency with a Macro cell, the eNodeB configuration also makes the cell selection or reselection to the Micro cell easier than to the Macro cell.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
29
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
EnhancementNone
DependencyNone
1.2.18.4 LBFD-00201804 Distance Based Inter-frequency Handover
AvailabilityThis feature is
applicable to Macro from eRAN3.0 not applicable to Micro not applicable to Lampsite
SummaryHuawei LTE eNodeB supports distance based inter-frequency handover.
BenefitsBetter End user Experience (Always Best Connected)
DescriptionWhen moving around away from the serving eNodeB with frequency F1, the user may still experience a relatively strong signal from F1 so that the condition of A2 event can't be satisfied to trigger an inter-frequency handover, even though the neighboring inter-frequency eNodeB signal is much better than F1. In order to make the user always keep the best connection, a distance based inter-frequency handover is employed.
When distance based HO algorithm is used, eNodeB should continuously measure the distance to each UE based on the TA measurement, once the distance exceeds an operator configured distance threshold, inter-frequency gap measurements of neighboring eNodeB will be triggered to find an optimal handover candidate to improve user performance
EnhancementNone
Dependency UE
UE should support for inter-frequency Gap measurements
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
30
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.2.18.5 LBFD-00201805 Service Based Inter-frequency Handover
AvailabilityThis feature is
applicable to Macro from eRAN3.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei LTE eNodeB supports service based inter-frequency handover. UE with specific service would be moved to the cell of the configured frequency.
BenefitsService Based Inter-frequency Handover is used to improve efficiency and capacity of whole system.
DescriptionThe operator could configure specific group of policies for service-based inter-frequency handovers. Each group will be associated with a QCI. The default policy is to prohibit handovers. A bearer of QCI 5 and QCIs of default bearers are not recommended to be configured to allow handovers.
When service based Inter-frequency handover algorithm is used, eNodeB should continuously monitor the UE service state. If QCI (each type of service is mapping to a QCI index) is changed, inter-frequency measurements of configured group will be triggered to find an optimal handover candidate.
EnhancementNone
Dependency UE
UE should support for inter-frequency Gap measurements
1.2.19 LBFD-002020 Antenna Configuration1.2.19.1 LBFD-00202001 UL 2-Antenna Receive Diversity
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
31
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
applicable to Lampsite from eRAN6.0
SummaryReceive diversity is a common type of multiple antennas technology to improve signal reception and to combat signal fading and interference. It improves network capacity and data rates. Huawei eNodeB supports both RX diversity mode and no RX diversity mode.
BenefitsThis feature can improve the receiver sensitivity and uplink coverage.
DescriptionReceive diversity is a technique to monitor signals at multiple frequencies from the same signal source, or to monitor time division signals at the same frequency from the same signal source, in order to combat signal fading and interference.
Receive diversity is one way to enhance the reception over uplink channels, including PUSCH, PUCCH, PRACH, and SRS.
Huawei eNodeB supports both RX diversity mode and no RX diversity mode. In RX diversity mode, the eNodeB can be configured with 2 antennas (2-way).
In RX diversity mode, the eNodeB does not require additional devices and works with the Maximum-Ratio Combining (MRC) or Interference Rejection Combining (IRC) algorithms. Compared with 1-way reception without RX diversity, 2-way RX diversity requires twice the number of RX channels. The number of RX channels depends on the settings of the antenna connectors.
EnhancementNone
Dependency eNodeB
RX diversity requires the eNodeB to provide enough RF channels and demodulation resources that can match the number of diversity antennas.
1.2.20 LBFD-002021 Reliability1.2.20.1 LBFD-00202101 Main Processing and Transport Unit Cold Backup
AvailabilityThis feature is
applicable to Macro from eRAN2.0 not applicable to Micro applicable to Lampsite from eRAN6.0
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
32
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
SummaryThe feature provides cold backup capability to the LMPT (LTE Main Processing and Transport Unit) or UMPT(Universal Main Processing and Transport Unit) board of Huawei eNodeB.
BenefitsIf there is only one LMPT board configured in the system, the failure of this board will cause long-time service outage of the base station. However, service can be automatically recovered within 3 minutes with LMPT redundancy. LMPT redundancy design is helpful for eNodeB to reach higher availability, greater than 99.999%.
DescriptionTwo LMPT boards are configured in the system. When the system starts, the arbitrator module located on each LMPT board decides which board becomes active or standby. The active board handles several control and operation functions and provides for the most common transport network connectivity requirements. When it detects hardware or software faults on the board, it will switch to the standby state. Meanwhile, the standby board switches to the active state. The service can be automatically recovered within 3 minutes. The operator can also manually trigger LMPT switchover by EMS (Element Management System).
Enhancement In eRAN3.0
The UMPT board also supports cold backup capability.
Dependency eNodeB
To support this feature, the eNodeB must be configured with two LMPT/UMPT boards.
1.2.20.2 LBFD-00202102 Cell Re-build Between Baseband Processing Units
AvailabilityThis feature is
applicable to Macro from eRAN2.0 not applicable to Micro applicable to Lampsite from eRAN6.0
SummaryIn Huawei eNodeB, multiple LTE Baseband Processing (LBBP) boards can be configured to serve multiple cells. When an LBBP fails, the cell/cells served by the failed LBBP can be rebuilt on another operating LBBP with spare resources or on a backup LBBP if available.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
33
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
BenefitsThis feature ensures the cell coverage by cell re-establishment and improves the system reliability in case of an LBBP failure.
DescriptionGenerally an eNodeB is equipped with multiple LBBP boards that serve multiple cells. The following figures show the example of configurations of 3*10M 2T2R with CPRI interface backup respectively.
Figure 1-1 3*10M 2T2R
When an LBBP board fails due to a hardware fault, communication interface failure, etc., the eNodeB is able to detect and locate the failure and tries to choose a target LBBP board on which the cell/cells are to be rebuilt. The target LBBP should have a CPRI connection with the RRU serving the cell/cells involved, as shown in the preceding figures. The selection of a target LBBP board mainly depends on the spare resources at the potential target LBBP board.
EnhancementNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
34
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Dependency eNodeB
The eNodeB should be equipped with at least two LBBP boards.
1.2.20.3 LBFD-00202103 SCTP Multi-homing
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryStream Control Transmission Protocol (SCTP) is the signaling bearer protocol of the S1/X2 interface. It provides the similar service features of TCP and UDP, but ensures reliability, in-sequence transport of messages with congestion control, and offers multi-homing support for fault recovery by failover between redundant network paths.
BenefitsThis feature provides reliability of signaling bearers.
Description
Figure 1-1 Stream Control Transmission Protocol
SCTP is the signaling bearer protocol of the S1/X2 interface. With this function, one SCTP association has two paths (IP-couple). An SCTP association is the logical channel between two SCTP ends. The two paths in one SCTP association are a master path and a slave path. Generally, the master path is active. When the master path fails, the slave path is activated.
EnhancementNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
35
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
DependencyNone
1.2.20.4 LBFD-00202104 Intra-baseband Card Resource Pool (user level/cell level)
AvailabilityThis feature is
applicable to Macro from eRAN2.0 not applicable to Micro applicable to Lampsite from eRAN6.0
SummaryIn this feature, the processing resources in a baseband processing board of Huawei eNodeB are aggregated into a baseband resource pool in which all they are shared for the load processing.
BenefitsThis feature ensures the stability and robustness of eNodeB, in which the processing resources are aggregated into a pool to share all load and thus to prevent individual resource from outage due to overload. The feature also improves the average cell capacity of eNodeB.
DescriptionThe baseband processing board of Huawei eNodeB consists of several processing resources. A baseband processing board is capable of supporting multiple cells depending on the bandwidths. In this feature, the processing resources are aggregated into a resource pool to be shared for user data processing by multiple cells. A new user will be assigned to a resource which has the least load. In an occasional situation, if a resource should be overloaded or in outage, the eNodeB can reduce the load of the individual resource or move its existing users to other resources.
EnhancementNone
Dependency eNodeB
This feature is only applicable to LBBPc.
1.2.21 LBFD-002027 Support of UE Category 1Availability
This feature is
applicable to Macro from eRAN1.0
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
36
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryE-UTRAN needs to respect the signaled UE radio access capability parameters when configuring the UE and when scheduling the UE. There are five categories defined in the protocol. This feature can enable base station to support UE category 1.
BenefitsThis feature can enable base station to support UE category 1.
DescriptionE-UTRAN needs to respect the signaled UE radio access capability parameters when configuring the UE and when scheduling the UE. There are five categories defined in the protocol. This feature can enable base station to support UE category 1.
Table 1-1 Downlink physical layer parameter values set by the field UE-Category
UE Category Maximum number of DL-SCH transport blocks bits received within a TTI
Maximum number of bits of a DL-SCH transport block received within a TTI
Total number of soft channel bits
Maximum number of supported layers for spatial multiplexing in DL
Category 1 10296 10296 250368 1
Category 2 51024 51024 1237248 2
Category 3 102048 75376 1237248 2
Category 4 150752 75376 1827072 2
Category 5 299552 149776 3667200 4
Table 1-2 Uplink physical layer parameter values set by the field UE-Category
UE Category Maximum number of bits of an UL-SCH transport block transmitted within a TTI
Support for 64QAM in UL
Category 1 5160 No
Category 2 25456 No
Category 3 51024 No
Category 4 51024 No
Category 5 75376 Yes
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
37
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Table 1-3 Total layer 2 buffer sizes set by the field UE-Category
UE Category Total layer 2 buffer size [KBytes]
Category 1 150
Category 2 700
Category 3 1400
Category 4 1900
Category 5 3500
EnhancementNone
Dependency UE
UE should support the same category as eNodeB.
1.2.22 LBFD-002031 Support of aperiodic CQI reportsAvailability
This feature is
applicable to Macro from eRAN3.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryAperiodic CQI is reported on PUSCH and the UE can be configured to report periodic CQI and aperiodic CQI together or individually.
BenefitsAperiodic CQI can offer more detailed channel quality information which may make the downlink spectrum efficiency better.
DescriptionAperiodic CQI is triggered by the UL scheduler periodically when needed and the CQI Request field in the UL grant is used to indicate the aperiodic CQI report. Higher layer-configured reporting modes will be supported, and the given mode is configured by the RRC.
Higher layer-configured
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
38
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Mode 3-0: A wideband CQI and one sub-band CQI for each sub-band are reported. Mode 3-1: A wideband CQI and one sub-band CQI for each sub-band per codeword are
reported. A wideband PMI is also reported.
Huawei eNodeB supports aperiodic CQI reporting , the reporting interval depends on the UL load. The interval will be lengthened adaptively when the UL load is high.
EnhancementNone
DependencyNone
1.2.23 LBFD-002032 Extended-QCIAvailability
This feature is
applicable to Macro from eRAN3.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei support extended QoS Class Identifier (extended QCI) (255 QCI including 9 standard QCI defined in 3GPP). Extended QCI can be used as operator defined QCI to support customer zed non-GBR service. Extended QCI index can be defined by operator and need SAE to support it.
BenefitsIt can be configurable flexibly by operator and meet multi need of operator who wants to operate the differentiated service.
DescriptionThis feature supports extended QCI, which means that MME send one extended QCI index in RAB assignment message. The eNodeB can configure these extended QCI and can be assigned radio resource differently according to the different QCI number and different scheduling weight factor.
The extended QCI can be configurable with Gold, Silver, and Bronze, which is the same as the ARP.
Huawei currently support extended non-GBR QCI, and the configurable scenario is that eNodeB get the QCI index firstly, set the ARP and QoS parameter ( PDB, PLER, schedule weight) related with QCI index.
EnhancementNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
39
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Dependency Others
It relates with SAE.
1.2.24 LBFD-002033 SCTP Congestion ControlAvailability
This feature is
applicable to Macro from eRAN6.0 applicable to Micro form eRAN6.0 applicable to Lampsite from eRAN6.0
SummaryIf a network has heavy traffic, Stream Control Transmission Protocol (SCTP) congestion control can be used to prevent SCTP association exceptions caused by SCTP signaling congestion. SCTP congestion control is triggered when the SCTP resources, including the central processing unit (CPU) and buffer resources, are insufficient.
In eRAN6.0, only downlink SCTP Congestion Control is supported.
BenefitsThis feature enhances the signaling message handling robustness in scenarios where the network is heavily loaded.
DescriptionIn an LTE system, control plane messages are used to ensure that the E-UTRAN runs properly and service connections are set up and released properly. The reliability of control plane messages plays a fundamental role in the LTE system. S1 signaling messages between an eNodeB and an MME and X2 signaling messages between eNodeBs are transmitted in compliance with SCTP.
As smartphones and applications such as instant messaging (IM) are popularized, signaling traffic increases sharply. SCTP resources, including the CPU and buffer resources, become a bottleneck in scenarios where the service traffic and signaling traffic are heavy. In such scenarios, SCTP congestion control helps to maintain signaling transmission robustness and reduce impacts on service key performance indicators (KPIs).
The SCTP congestion control procedure includes SCTP congestion detection, back-pressure, and signaling congestion control at the application layer. The eNodeB determines whether SCTP signaling is congested based on the SCTP resource usage. If downlink SCTP signaling is congested, the eNodeB informs EPC by normal SCTP mechanism. EPC side decreases signaling traffic to reduce signaling load of eNodeB by congestion control procedure. If uplink SCTP signaling is congested, the eNodeB informs the application layer of the congestion by back-pressure.
EnhancementNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
40
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Dependency CN
Downlink SCTP control depends on the support of congestion control procedure in EPC side as defined in RFC 4960.
1.2.25 LBFD-002034 RRU Channel Cross Connection Under MIMOAvailability
This feature is
applicable to Macro from eRAN2.0 not applicable to Micro not applicable to Lampsite
SummaryThis feature enables eNodeB provides service to one sector through two RRUs. When one RRU fails, it will not lead to the total outage of that sector.
This feature is changed to basic feature from optional feature since eRAN6.0.
BenefitsWhen deployed in the field, perhaps the RRU is installed on top of the tower or the base station is installed in inaccessible area. The equipment cannot be easily maintained. In this case, if one RRU fails, the sector will be out of service for a long time. However, with this new scheme, one RRU failure will not cause the outage of the whole sector so that the service coverage can be ensured.
By reliability prediction, the availability of RRU will increase from 5 nine's (0.99999844) to 6 nine's (0.99999932). In addition, this scheme does not increase any hardware cost.
DescriptionThis scheme can greatly increase equipment reliability with no additional hardware cost. By utilizing the independency of the MIMO channels, the sector service can be processed through different RRUs. When one RRU fails, the other RRU can still process the service data of that sector so the total outage of that sector will not occur. Meanwhile, the performance of that faulty sector will be decreased. This scheme can be applied in multiple sectors configuration and MIMO architecture.
Taking 2T2R RRU for example, there are three RRUs (from left to right which are RRU1, RRU2 and RRU3) The left chart is for the legacy scheme and the right one is for the load sharing scheme. Antenna 1 is connected to RRU1 and RRU2. Antenna 2 is connected to RRU2 and RRU3. Antenna 3 is connected to RRU3 and RRU1. In the legacy scheme, when one RRU fails, the sector connected is totally out of service. While applying MIMO load sharing scheme, when one RRU, for example RRU1 fails, the other antenna of that sector is connected to RRU2, service in that faulty sector can still be processed. In the meanwhile, that operation mode is changed from 2T2R to 1T1R and the performance decreases (such as coverage area, throughput, etc). On the other hand, as sector 3 uses one transmit/receive channel of RRU1, the performance decreases as well. Moreover, because the antenna mode
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
41
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
has change for both sector1 and sector3, it is necessary to reconfigure the cell data, which will cause 20s outage of service.
Figure 1-1 RRU channel cross connection under MIMO
Figure 1-2 Comparing with no MIMO load Sharing
EnhancementNone
Dependency Others
This feature is more suitable for RRUs installed on top of the tower.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
42
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.2.26 LBFD-070102 MBR>GBR ConfigurationAvailability
This feature is
applicable to Macro from eRAN7.0 applicable to Micro form eRAN7.0 applicable to Lampsite from eRAN7.0
SummaryThe eNodeB allows the maximum bit rate (MBR) to be greater than the guaranteed bit rate (GBR).
BenefitsSetting of the MBR to be greater than the GBR allows applications to take advantage of additional system capacity when it is available, thereby improving resource utilization and user experience. For details, see 3GPP TS 23.860.
DescriptionThe definition of MBR allows the increasing real-time services (such as voice and video services), whose data rates are elastic, to make use of additional network resources that may be available. The GBR can be set to the minimum data rate at which the real-time services can be carried, and the MBR can be set to the maximum data rate at which the optimal user experience is achieved. When the E-UTRAN is not congested and idle network resources are available, the real-time services carried on the GBR bearers can reach rates between the GBR and the MBR.
EnhancementNone.
DependencyNone.
1.3 Transmission & Security1.3.1 LBFD-003001 Transmission Networking1.3.1.1 LBFD-00300101 Star Topology
AvailabilityThis feature is
applicable to Macro from eRAN1.0
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
43
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryStar topology is easy to implement and manage with high reliability. It provides simple topology between eNodeB interfaces.
Benefits The simplest topology Simple management and high reliability
Description
Figure 1-1 Star topology
The eNodeB supports star topology. eNodeBs connect to the core network by layer2 or layer3 data network. The interface between the eNodeB and core network element is the S1 interface.
There are also connections between eNodeBs by the X2 interface, which enable information exchange between the eNodeBs
EnhancementNone
DependencyNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
44
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.3.1.2 LBFD-00300102 Chain Topology
AvailabilityThis feature is
applicable to Macro from eRAN2.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryeNodeBs can be connected in chain topology applied to the strip-shape areas of sparse population.
BenefitsChain networking can reduce costs of transmission equipment, engineering, construction, and transmission link lease.
DescriptioneNodeBs can be connected in chain topology. This network topology is applicable to the strip-shape areas of sparse population, such as expressways and railways. In these areas, the chain topology can meet the requirement with much less transmission equipment. However, chain networking reduces reliability because signals are transferred across many intermediate systems.
The following figure shows the chain topology.
Figure 1-1 Chain topology
EnhancementNone
DependencyNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
45
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.3.1.3 LBFD-00300103 Tree Topology
AvailabilityThis feature is
applicable to Macro from eRAN2.0 not applicable to Micro applicable to Lampsite from eRAN6.0
SummaryeNodeBs can be connected in tree topology applied to microwave transmission networks.
BenefitsTree networking is suitable for microwave transmission networks. Tree topology requires fewer transmission links than star networking.
DescriptionThe eNodeB can be connected in tree topology. In most scenarios, the MW (Microwave) network is typically in tree topology. It is suitable for the MW network.
The use of transport lines is less than that for star networking. However, tree connections reduce reliability because signals are transferred across many intermediate systems. A fault occurring in the upper-level eNodeB may affect the operation of the lower-level eNodeBs. The networking topology is applicable to a large, sparsely populated area. Capacity expansion may result in reconstruction of the network.
The following figure shows the tree topology.
Figure 1-1 Tree topology
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
46
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
EnhancementNone
Dependency eNodeB
The UMPT card, which provides E1/T1 interfaces, is required.
1.3.2 LBFD-003002 Basic Qos Management1.3.2.1 LBFD-00300201 DiffServ QoS Support
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryHuawei supports DiffServ (Differentiated Services) to provide QoS guarantee by classifying and managing different traffic in the network.
BenefitsThis feature provides a kind of QoS guarantee mechanism. It is a standard mechanism used by Mainstream vendors.
DescriptionDiffServ can provide QoS in the network. It is a kind of QoS guarantee mechanism that classifies and manages different traffic with parameters of IP packets, such as DSCP (DiffServ Code Point) or TOS (Type of Service).
There are three important concepts in the DiffServ mechanism, including Classification, Marking, and PHB (Per-Hop Behavior). The relationship between them is that Marking marks different traffic with different PHBs by Classification.
The definition of PHB is as follows:
Default PHB is typically for best-effort traffic. Expedited Forwarding (EF) PHB is for low-loss and low-latency traffic. Assured Forwarding (AF) is a behavior group. Class Selector PHB is defined to maintain backward compatibility with the IP
Precedence field.
The classification of LTE traffic is based on QoS Class Indicators (QCIs). With Huawei configuration tool, users can configure the relationship between QCI and DSCP, i.e. the Marking way. The DSCP is used to describe the priority of PHB. The table below is an example of relationship between QCI and DSCP.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
47
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Table 1-1 Relationship between QCI and DSCP
Data Type QCI Resource Type DSCP
User plane 1 GBR 0x2E
2 0x1A
3 0x22
4 0x1A
5 Non-GBR 0x2E
6 0x12
7 0x12
8 0x0A
9 0
Control plane SCTP 0x2E0x30
OM MML 0x2E0x30
FTP 0x0E
IP clock 0x2E0x30
EnhancementNone
DependencyNone
1.3.3 LBFD-003003 VLAN Support (IEEE 802.1p/q)Availability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature enables Virtual Local Area Network (VLAN) functionality to provide traffic differentiation, manage data priority and security scheduling at the MAC layer.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
48
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Benefits Traffic isolation at the MAC layer Priority at the MAC layer Security at the MAC layer
DescriptionThe eNodeB supports the Virtual Local Area Network (VLAN) functionality, complying with the IEEE 802.1p/q protocol. It provides traffic isolation, such as marking different VLANs for OAM data and traffic data, and priority and security at the MAC layer.
The following two VLAN Marking ways are applicable:
Marking VLAN tag according to DSCP Marking VLAN tag according to the next-hop IP address
EnhancementNone
DependencyNone
1.3.4 LBFD-003005 Synchronization1.3.4.1 LBFD-00300501 Clock Source Switching Manually or Automatically
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature enables manual or automatic switching between clock sources.
BenefitsIf unexpected events occur in the current clock sources, the system will not be affected.
DescriptionThe eNodeB can work in multiple clock synchronization modes. The system clock source can be chosen in a convenient and flexible manner. When one clock source fails, the system clock can be manually or automatically switched to another available one.
1. For phase synchronization, the clock source can be manually or automatically switched.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
49
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Following clock source supports manually switching:− Synchronization with GPS− Synchronization with the clock over IP (IEEE 1588V2)− Synchronization with 1PPS + TODFollowing clock resource supports automatically switching:− Between GPS and IEEE 1588V2− Between GPS and 1PPS+TOD
2. For frequency synchronization, the clock source can be manually switched. Following clock source supports manually switching:− Synchronization with Ethernet(ITU-T G.8261)− Synchronization with the clock over IP (IEEE 1588V2)− Synchronization with the clock over IP (Huawei proprietary solution)− Synchronization with GPS− Synchronization with the BITS− Synchronization with E1/T1 interface− Synchronization with 1PPS
In addition to the previous clock sources, the eNodeB can work with the local oscillator.
EnhancementNone
DependencyNone
1.3.4.2 LBFD-00300502 Free-running Mode
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe free-running mode is an alternative mode to the clock sources if all clocks fail.
BenefitsWhen all clock sources are lost, this feature can keep the eNodeB in normal service for up to 90 days.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
50
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
DescriptionWhen all clock sources are lost, the eNodeB internal clock can work in the free-running mode to keep the eNodeB running.
The enhanced stratum 3 Oven Controlled Crystal Oscillator (OCXO) with a high accuracy works as the master clock of the eNodeB. The OCXO can keep the eNodeB in normal service for up to 90 days.
EnhancementNone
DependencyNone
1.3.4.3 LBFD-00300503 Synchronization with GPS
AvailabilityThis feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe eNodeB can work in multiple clock synchronization modes to suit different clock topologies. Global Positioning System (GPS) can be one of the synchronization sources.
BenefitsThis feature provides GPS as one of the synchronization sources. The eNodeB internal clock can be synchronized with the transport network and no auxiliary clock equipment is needed, in order to reduce the cost. The synchronized clock is of the required accuracy to meet both radio frequency and transmission network requirements.
DescriptionIn compliance with 3GPP, the eNodeB clock must have a higher clock precision. The frequency stability of the 10-MHz master clock of the eNodeB should be lower than ±0.05 ppm.
It is required if a GPS clock is used as the clock source.
The clock signals are processed and synchronized as follows:
The GPS antenna and feeder system receives GPS signals at 1575.42 MHz, and transmits the signals to the GPS card. The system can simultaneously trace up to eight (normally three or four) satellites. The GPS card processes the signals and transmits them to the main clock module.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
51
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
EnhancementNone
DependencyNone
1.3.4.4 LBFD-00300504 Synchronization with BITS
AvailabilityThis feature is
applicable to Macro from eRAN2.0 not applicable to Micro applicable to Lampsite from eRAN6.0
SummaryThe eNodeB can work in multiple clock synchronization modes to suit different clock topologies. Building Integrated Timing Supply System (BITS) can be one of the synchronization sources.
BenefitsThis feature provides BITS as one of the synchronization sources. The eNodeB internal clock can be synchronized with the transport network and no auxiliary clock equipment is needed, in order to reduce the cost. The synchronized clock is of the required accuracy to meet both radio frequency and transmission network requirements.
DescriptionIn compliance with 3GPP, the eNodeB clock must have a higher clock precision. The frequency stability of the 10-MHz master clock of the eNodeB should be lower than ±0.05 ppm.
The eNodeB can synchronize its clocks with the 2-MHz clock signal from an external reference clock. The reference clock can be a BITS or a 2-MHz clock from the transmission equipment. Through phase locking and frequency dividing, the main clock module converts the clock signals into various clock signals required by the eNodeB.
EnhancementNone
Dependency eNodeB
USCU(Universal Satellite Card and Clock Unit) card is required
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
52
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.3.4.5 LBFD-00300505 Synchronization with 1PPS
AvailabilityThis feature is
applicable to Macro from eRAN2.0 not applicable to Micro applicable to Lampsite from eRAN6.0
SummaryThe eNodeB can work in multiple clock synchronization modes to suit different clock topologies. 1PPS+TOD can be one of the synchronization sources.
BenefitsThis feature provides 1PPS+TOD as one of the synchronization sources. The eNodeB internal clock can be synchronized with the transport network and no auxiliary clock equipment is needed, in order to reduce the cost. The synchronized clock is of the required accuracy to meet both radio frequency and transmission network requirements.
DescriptionIn compliance with 3GPP, the eNodeB clock must have a higher clock precision. The frequency stability of the 10-MHz master clock of the eNodeB should be lower than ±0.05 ppm.
This feature provides 1PPS+TOD as one of the synchronization sources.
EnhancementNone
Dependency eNodeB
USCU(Universal Satellite Card and Clock Unit) card is required
1.3.5 LBFD-003006 IPv4/IPv6 Dual StackAvailability
This feature is
applicable to Macro from eRAN2.2 not applicable to Micro applicable to Lampsite from eRAN6.0
SummaryA fundamental IPv4-to-IPv6 transition technology involves the presence of two Internet Protocol software implementations in an operating system, one for IPv4 and another for IPv6.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
53
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
This feature provides support for IPv6 protocol stack. It also enables IPv4 and IPv6 protocol stack work at the same time. Application level protocols (e.g. S1 and X2) over IPv6 are not supported by this feature.
BenefitsThe key to a successful IPv6 transition is compatibility with the large installed base of IPv4 hosts and routers. Maintaining compatibility with IPv4 while deploying IPv6 will streamline the task of transitioning the Internet to IPv6.
DescriptionThe most straightforward way for IPv6 nodes to remain compatible with IPv4-only nodes is by providing a complete IPv4 implementation. IPv6 nodes that provide complete IPv4 and IPv6 implementations are called "IPv6/IPv4 dual-stack nodes". IPv6/IPv4 dual-stack nodes have the ability to send and receive both IPv4 and IPv6 packets. They can directly interoperate with IPv4 nodes using IPv4 packets, and also directly interoperate with IPv6 nodes using IPv6 packets.
Huawei eNodeB could be operated in one of the three modes:
With IPv4 stack enabled and IPv6 stack disabled. With IPv6 stack enabled and IPv4 stack disabled. With both stacks enabled.
EnhancementNone
DependencyNone
1.4 Operation & Maintenance1.4.1 LBFD-004001 Local Maintenance of the LMTAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature is used in local maintenance of eNodeB.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
54
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
BenefitsLocal maintenance of eNodeB is available when centralized U2000 management is not available, when the transmission between U2000 and eNodeB is not available or when faults occur and field operation is required.
DescriptionThe Local Maintenance Terminal (LMT) provides the following functions and tools:
Execution of MML commands Querying of eNodeB alarms Local eNodeB commissioning functions (applicable, for example, when the transmission
between the Huawei iManager U2000 and eNodeB is not available), such as download and activation of software
Local eNodeB expert fault diagnosis functions Real-time performance monitoring functions, such as sector performance monitoring,
RRU performance monitoring, spectrum detection
Enhancement In eRAN2.0
The LMT functions can be achieved through a web browser.
Dependency OSS
A web browser is required to achieve the function.
1.4.2 LBFD-004002 Centralized U2000 ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe Huawei iManager U2000 provides FCPSS management functions for operators at the management center.
BenefitsAll LTE network elements can be managed at the management center, which effectively reduces OPEX.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
55
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
DescriptionThe Huawei iManager U2000 provides all necessary fault management, configuration management, performance management, security management and software management (FCPSS defined by 3GPP) management functions to help operators to manage their network elements on a sub-network.
FCPSS involves the following contents:
Centralized fault management Centralized configuration management Centralized performance management Centralized security management Centralized software management
EnhancementNone
Dependency OSS
The Huawei iManager U2000 is required.
1.4.3 LBFD-004003 Security Socket LayerAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummarySecurity Socket Layer (SSL) is a layer between the TCP layer and the O&M application layer. SSL provides the secured data transfer function between the eNodeB and the Huawei iManager U2000
BenefitsAll remote operation and maintenance tasks are performed through encrypted protocols.
DescriptionSecurity Socket Layer (SSL) is a layer between the TCP layer and the O&M application layer. SSL provides the secured data transfer function between the eNodeB and the Huawei iManager U2000. All O&M application data transferred through SSL is encrypted. FTP over SSL is also supported.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
56
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Enhancement In eRAN3.0
This feature supports TLSv1.2. Transport Layer Security (TLS) and its predecessor-Secure Sockets Layer (SSL), are cryptographic protocols that provide communications security between eNodeBs and Huawei iManager U2000 above Transport Layer. TLSv1.2 is the latest version of TLS series. And TLS1.2 supports stronger authentication algorithm SHA256.
Dependency OSS
The Huawei iManager U2000 is required.
1.4.4 LBFD-004004 Software Version Upgrade ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature provides efficient and correct installation and upgrade of the software and version management functions.
BenefitsThe eNodeB software management enables efficient and correct software installation, upgrade, and version management.
DescriptionThe eNodeB software management covers the following functions:
Efficient and correct installation and upgrade of the software Automatic compatibility check on the software and hardware versions to verify a
successful software installation and upgrade. Automatic data conversion for the software upgrade, which requires no manual
configuration updates. Software download by configuration can reduce 30% of the software package size and
shorten the download time. For adding a board, the system supports automatic download of software files for the board from the Huawei iManager U2000 if the files are not downloaded to eNodeB previously.
If the network recovers in 1 hour after breakdown, the system supports resumption of the software download with no need to download the software from scratch.
A maximum of 600 eNodeBs can be selected to download and activate the software in batches automatically.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
57
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Hot patch can be upgraded together with software in Huawei iManager U2000 software management wizard.
Version management, for example, the hardware and software version query
The process for upgrading software at a network element involves the following two activities:
Downloading the software package from the Huawei iManager U2000 to the eNodeB. This may take some time because of the limited bandwidth of the OM link but does not have impacts on services.
Running the software activation command on the Huawei iManager U2000 client. The system will automatically load the software to the target boards and activate the software. To activate the software, the target boards will be reset and the service on the boards will be disrupted.
The above-mentioned two activities can be done separately. E.g. downloading software package to eNodeBs at daytime and activating the software at midnight. The separate software upgrade procedure helps to reduce the risk of software upgrade failures and service disruption of the sub-network.
EnhancementNone
Dependency OSS
The Huawei iManager U2000 is required.
1.4.5 LBFD-004005 Hot Patch ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature provides hot patch management functions, such as installation, uninstall and rollback.
BenefitsThe eNodeB supports the hot patches so that the software bugs can be fixed without interrupting the ongoing services.
DescriptionA hot patch is a patch that is used to fix bugs and does not interrupt the ongoing services. Huawei LTE hot patch management involves the following functions:
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
58
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Hot patch installation.
There are two ways to install a released hot patch package on the eNodeB:
Running only a single installation command: In this way, the patch is downloaded, loaded, activated and confirmed automatically.
Running different commands at separate steps of the patch installation: In this way, users have full control over the installation procedure: download, load, activate and confirm.
Rollback of the last installed hot patch Uninstall of the hot patch
EnhancementNone
Dependency OSS
Hot patch management can be implemented on the Huawei iManager U2000 or the eNodeB LMT.
1.4.6 LBFD-004006 Fault ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature provides automatic fault supervision and handling of eNodeB.
BenefitsThis feature enables the automatic fault supervision of the equipment in the network elements. With real-time alarm lists and alarm logs, operators can have a comprehensive view of the actual status of the network at any time.
DescriptionFault management involves fault detection, fault handling, fault correlation, and fault reporting. With these features, operators can be informed as soon as the fault occurs in the network and take proper actions to minimize or prevent service disruption.
Fault detection
Fault detection includes physical layer and link layer environment monitoring and KPI alarm monitoring and other fault detection. A small portion of faults may have a negative impact on the traffic if self-testing, such as RAM self-testing and transport link loopback testing, is performed. Among those faults, some are detected automatically in the board startup phase, and some can be manually triggered by executing fault testing commands.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
59
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Fault detection methods are carefully designed to avoid false alarms and intermittent alarms.
Fault handling
The eNodeB will perform fault isolation and fault automatic recovery to minimize the impacts on service.
Fault correlation
Fault management supports a run-time fault correlation handling mechanism and makes it possible to notify operators of the most important alarms (the root cause and impacts on the traffic) instead of all the related ones when a fault occurs. The number of alarms can be greatly reduced in this way, which makes it easier to locate and solve the network problems. This mechanism is predefined and embedded in the network elements, and operators can customize more alarm correlation handling rules on the Huawei iManager U2000.
Fault reporting
Faults are reported to users in the form of alarms. Because of the alarm correlation function, the information of the correlation between alarms is contained in alarms. If any correlative alarms occur, operators can get the root alarm by simply right-clicking the service-affecting faults.
The operators can browse real-time alarm information, query history alarm information, and store alarm information. The online help provides detailed troubleshooting methods for each type of alarm.
Enhancement In eRAN2.0
Huawei LTE eRAN2.0 supports KPI alarm detection. In eRAN2.2
When RRU power supply is AC, RRU could detect AC power down and provide warning signal to the eNodeB.
Dependency OSS
Fault management can be implemented on the Huawei iManager U2000 or the eNodeB LMT.
1.4.7 LBFD-004007 Configuration ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature provides online and offline configuration functions which support quick installation, expansion and configuration of the network.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
60
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
BenefitsThis feature provides a good overview of the current status of the network and supports fast installation, expansion and configuration of the network.
DescriptionConfiguration management provides operators with a means to collect and manage the data of the network element. The manageable element data covers the physical aspect (equipment) and logical/functional aspect (such as cells and links). The graphic user interface makes it easy to implement the management.
To minimize the impact of reconfiguration on the system, Huawei configuration management function has the following important features:
Physical modifications are independent of the related logical modifications. All the required modifications to satisfy a defined task are completely checked to ensure
their validity before the modifications can be applied to the eNodeB. Configuration data consistency between the NE and the Huawei iManager U2000 are
always ensured.
Both offline configuration and online configuration are supported.
Offline configuration
CME (Configuration Management Express) is a graphic offline configuration tool. In addition to general configuration functions, it provides some configuration templates to ease site deployment jobs. It also provides some GUI wizards to help user to finish capacity expansion and migration jobs.
Online configuration
All configuration data can be modified and queried online through MML commands.
Enhancement In eRAN2.0
GUI wizards are added to help users with capacity expansion and migration jobs.
Dependency OSS
Configuration management can be implemented on the Huawei iManager U2000 or the LMT.
1.4.8 LBFD-004008 Performance ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
61
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
SummaryThis feature provides various performance measurement (PM) counters to monitor the performance of the eNodeB. The real-time KPI monitoring is an enhanced feature to help user locate performance problems quickly.
BenefitsThe performance management function provides an efficient way to monitor the network performance so that network troubleshooting and optimization can be implemented, and the real-time KPI monitoring is a more efficient feature.
DescriptionPerformance measurement gives the detailed information of the network. Such information facilitates troubleshooting and network optimization.
PM administration
The performance measurement administration provides operators with a means to manage the available measurements.
For the new commissioning network elements (eNodeB), the predefined performance measurements will start after initial startup phase. The performance measurements can be suspended and resumed manually.
The network elements (eNodeB) provide machine-machine interfaces, allowing the Huawei iManager U2000 to collect the necessary statistics and to set the related parameters including statistical counters and the measurement period.
The statistics are obtained by the Huawei iManager U2000 in binary format in every measurement period.
Each eNodeB can store a maximum of 288 files as backups that are useful when data transfer fails, which makes it possible for the Huawei iManager U2000 to recollect the lost data later.
− If the measurement period is 15 minutes, an eNodeB can store measurement results sampled in a maximum period of 72 hours.
− If the measurement period is 60 minutes, an eNodeB can store measurement results sampled in a maximum period of 288 hours.
PM counters
The PM counters include key counters and other counters. The key counters are used to generate the key performance indicators (KPIs) of the network, which are defined on the Huawei iManager U2000, and these counters are predefined and initialized as soon as the eNodeB starts. The KPIs, related original counters and formulas can be added, modified and deleted on the Huawei iManager U2000. Other counters reflecting the other aspects of network performance can be started when needed.
Real-time KPI monitoring
This feature provides the monitoring of KPIs and graphical representation of network performance. Therefore, it is convenient for troubleshooting, drive tests and network optimization. The real-time KPI measurement period of each monitoring task can vary, but must be a multiple of 30 seconds within the range of 30 seconds to 15 minutes. By default, eNodeBs of eRAN2.2 and later releases use a monitoring period of 1 minute.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
62
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
EnhancementNone
Dependency OSS
Performance management is implemented on the Huawei iManager U2000 or LMT.
1.4.9 LBFD-004009 Real-time Monitoring of System Running InformationAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature provides the function of monitoring the running information of the equipment, RF system, cells, subscribers and transport links.
BenefitsThis feature is convenient for troubleshooting, drive tests and network optimization.
DescriptionThis feature provides real-time monitoring and graphical representation of system operation information and quality. It is a test facility which helps operators to diagnose faults through precise information about cells, subscribers and links..
The following monitoring items are supported:
Equipment running information monitoring: involving clock source quality Subscriber-level running information monitoring: involving SIR measurement and UE
TX power Cell-level running information monitoring: involving the number of cell users,
throughput, and resource block usage Transport link running information monitoring: involving SCTP links and IP paths RF monitoring: involving RF performance and RF interference detection
EnhancementNone
DependencyNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
63
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
1.4.10 LBFD-004010 Security ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature provides the user authorization, system data backup and restore, security log auditing and security-related alarms functions.
BenefitsThis feature provides the user authorization and management mechanism to enhance network security.
DescriptionSecurity management covers the following functions to enhance system security:
User management: This mechanism allows setting of user accounts and permissions, so that the related authorized groups and operators can be managed.
System data backup and restoration Collection of operation logs and auditing of security logs Triggering of alarms when, for example, network attacks are detected or the number of
unauthorized sessions exceeds the preset threshold
Enhancement In eRAN2.0
Security alarms are added.
Dependency OSS
The Huawei iManager U2000 is required.
1.4.11 LBFD-004011 Optimized eNodeB Commissioning SolutionAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
64
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
SummaryThe optimized eNodeB commissioning solution supports USB commissioning and automatic obtaining of software and configuration data from the Huawei iManager U2000.
BenefitsThis feature simplifies the eNodeB commissioning procedure.
DescriptionThis feature simplifies the on-site commissioning procedure from the following aspects:
If eNodeB data is ready on the Huawei iManager U2000 and transmission of this eNodeB is ready, Huawei on-site manual commissioning task is very simple:
Installing the hardware and powering on the eNodeB Waiting for the eNodeB startup If field engineer has a laptop, the engineer can use laptop to input DID (Deployment ID).
iManager U2000 can use this information to automatically select a correct configuration data.
Or , filed engineer can call the administration center and report the Electronic Serial Number (ESN) of the eNodeB
In the procedure, the newly installed equipment will automatically set up the connection with the Huawei iManager U2000 by using DHCP, download software and data from the Huawei iManager U2000, and install the software.
USB commissioning is supported. The associated software and data of the eNodeB can be copied to a USB disk at the administration center. A local commissioning engineer only needs to obtain the USB disk, install the hardware, and connect the USB disk to the USB port on the eNodeB. After that, the eNodeB can automatically install the software and load data, start up, and set up the connection to the Huawei iManager U2000. No more local configuration is required.
EnhancementNone.
Dependency OSS
U2000 or an USB for USB commissioning is required.
1.4.12 LBFD-004012 Environment MonitoringAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
65
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
SummaryThis feature provides environment fault alarming and customized environment alarms functions.
BenefitsThis feature enables centralized environment monitoring of Huawei eNodeB equipment.
DescriptionThis feature enables centralized environment monitoring of Huawei eNodeB equipment in terms of, for example, the temperature, humidity, smoke, water immersion, access control, and power supply. Besides, Huawei equipment can be connected to third-party analog and digital sensors, which enable operators to customize environment alarms.
EnhancementNone
Dependency OSS
The Huawei iManager U2000 or LMT is required.
1.4.13 LBFD-004013 Inventory ManagementAvailability
This feature is
applicable to Macro from eRAN1.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThe Huawei iManager U2000 retrieves inventory information automatically from the eNodeB after commissioning and synchronize the information on the eNodeB every day.
BenefitsWith this function, operators can obtain the timely and accurate inventory data of the existing network for decision making.
DescriptionInventory management helps operators to manage the asset information of the network. With this function, the assets can be queried and managed on the Huawei iManager U2000.
The objects which are managed by this function include physical objects (such as racks, frames, slots, boards, ports, and fans) and logical objects (such as software and patches).
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
66
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
When requested from the Huawei iManager U2000, an asset information file in .xml format is generated and is sent to the Huawei iManager U2000. The Huawei iManager U2000 stores the uploaded information in the network inventory database.
The Huawei iManager U2000 retrieves inventory information automatically from the eNodeB after commissioning and synchronize the information on the eNodeB every day.
Enhancement In eRAN2.0
The Huawei iManager U2000 retrieves inventory information automatically from the eNodeB after commissioning.Inventory change notification function has been added to eNodeB. When inventory changes in eNodeB, a notification will be sent from eNodeB to U2000(Micro eNodeB will not send this notification), so that the inventory information could be synchronized quickly between U2000 and eNodeB.
Dependency OSS
The Huawei iManager U2000 is required.
1.4.14 LBFD-004014 License ManagementAvailability
This feature is
applicable to Macro from eRAN2.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryThis feature involves the eNodeB license control.
BenefitsWith this feature, the operators can purchase the license based on the network development, thus reducing the initial cost of the network deployment.
DescriptionThe license file is used to determine whether the optional features are available and how many optional features are available.
The license file can be downloaded remotely to the eNodeB. The operators can manage and query the contents in the license file through the LMT or the U2000 client.
The license file is stored in the eNodeB.
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
67
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
Figure 1-1 License file management
New or upgraded license files can be ordered from Huawei.
EnhancementNone
DependencyNone
1.4.15 LBFD-004015 License Control for UrgencyAvailability
This feature is
applicable to Macro from eRAN3.0 applicable to Micro form eRAN3.0 applicable to Lampsite from eRAN6.0
SummaryWith this feature, the license limitation is withdrawn in emergencies, so the operator can handle the sudden increase of network capacity.
BenefitsThis feature helps operator to face the situations where there is an unusual increase of traffic (sport events, New Year…) by enabling a temporary increase of RAN resource, avoiding permanent over-dimensioning and thus adapting the capacity costs to the real usage.
DescriptionThe license limitation is withdrawn through manual execution of the MML commands on the LMT or U2000. Thus, the equipment can be used effectively to optimum capacity.
For each R version, the operation personnel have three chances to withdraw the license limitation through the MML commands. The operation takes effect immediately after the
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
68
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 1 Basic Features
commands are executed. The validity period is seven days. When the three chances are used up, a new chance can be obtained only through the software upgrade.
EnhancementNone
DependencyNone
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
69
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
2 Acronyms and Abbreviations
Table 1-1 Acronyms and Abbreviations
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
70
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
3GPP Third Generation Partnership Project
ABS Almost-blank subframe
ACK acknowledgment
ACL Access Control List
AES Advanced Encryption Standard
AFC Automatic Frequency Control
AH Authentication Header
AMBR Aggregate Maximum Bit Rate
AMC Adaptive Modulation and Coding
AMR Adaptive Multi-Rate
ANR Automatic Neighboring Relation
ARP Allocation/Retention Priority
ARQ Automatic Repeat Request
BCH Broadcast Channel
BCCH Broadcast Control Channel
BITS Building Integrated Timing Supply System
BLER Block Error Rate
CA Carrier aggregation
C/I Carrier-to-Interference Power Ratio
CCCH Common Control Channel
CDMA Code Division Multiple Access
CEU Cell Edge Users
CGI Cell Global Identification
CP Cyclic Prefix
CPICH Common Pilot Channel
CQI Channel Quality Indicator
CRC Cyclic Redundancy Check
CRS Cell-specific reference signal
CSI-RS Channel state information reference signal
DCCH Dedicated Control Channel
DHCP Dynamic Host Configuration Protocol
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
71
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
72
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
DiffServ Differentiated Services
DL-SCH Downlink Shared Channel
DRB Data Radio Bearer
DRX Discontinuous Reception
DSCP DiffServ Code Point
DTCH Dedicated Traffic Channel
ECM EPS Control Management
eCSFB Enhanced CS Fallback
EDF Early Deadline First
EF Expedited Forwarding
eHRPD Evolved high rate packet data
eICIC Enhanced Inter-cell Interference Coordination
eMBMS evolved Multimedia Broadcast Multimedia System
EMM EPS Mobility Management
EMS Element Management System
eNodeB evolved NodeB
EPC Evolved Packet Core
EPS Evolved Packet System
ESP Encapsulation Security Payload
ETWS Earthquake and Tsunami Warning System
E-UTRA Evolved –Universal Terrestrial Radio Access
FCPSS Fault, Configuration, Performance, Security and Software Managements
FDD Frequency Division Duplex
FEC Forward Error Correction
FTP File Transfer Protocol
GBR Guaranteed Bit Rate
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
73
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
GERAN GSM/EDGE Radio Access Network
GPS Global Positioning System
HARQ Hybrid Automatic Repeat Request
HII High Interference Indicator
HMAC Hash Message Authentication Code
HMAC_MD5 HMAC Message Digest 5
HMAC_SHA HMAC Secure Hash Algorithm
HO Handover
HRPD High Rate Packet Data
ICIC Inter-cell Interference Coordination
IKEV Internet Key Exchange Version
IMS IP Multimedia Service
IP PM IP Performance Monitoring
IPsec IP Security
IRC Interference Rejection Combining
KPI Key Performance Indicator
CME Configuration Management Express
LMT Local Maintenance Terminal
MAC Medium Admission Control
MIB Master Information Block
MCH Multicast Channel
MCCH Multicast Control Channel
MCS Modulation and Coding Scheme
MIMO Multiple Input Multiple Output
min_GBR Minimum Guaranteed Bit Rate
MME Mobility Management Entity
MML Man-Machine Language
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
74
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
75
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
MOS Mean Opinion Score
MRC Maximum-Ratio Combining
MTCH Multicast Traffic Channel
MU-MIMO Multiple User-MIMO
NACC Network Assisted Cell Changed
NACK Non acknowledgment
NAS Non-Access Stratum
NRT Neighboring Relation Table
OCXO Oven Controlled Crystal Oscillator
OFDM Orthogonal Frequency Division Multiplexing
OFDMA Orthogonal Frequency Division Multiplexing Access
OI Overload Indicator
OMC Operation and Maintenance Center
OOK On-Off-Keying
PBCH Physical Broadcast Channel
PCCH Paging Control Channel
PCFICH Physical Control Format Indicator Channel
PCH Paging Channel
PCI Physical Cell Identity
PDB Packet Delay Budget
PDCCH Physical Downlink Control Channel
PDCP Packet Data Convergence Protocol
PDH Plesiochronous Digital Hierarchy
PDSCH Physical Downlink Shared Channel
PF Proportional Fair
PHB Per-Hop Behavior
PHICH Physical Hybrid ARQ Indicator Channel
PM Performance Measurement
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
76
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
77
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
PLMN Public Land Mobile Network
PMCH Physical Multicast Channel
PRACH Physical Random Access Channel
PUCCH Physical Uplink Control Channel
PUSCH Physical Uplink Shared Channel
QAM Quadrature Amplitude Modulation
QCI QoS Class Identifier
QoS Quality of Service
QPSK Quadrature Phase Shift Keying
RA Random Access
RACH Random Access Channel
RAM Random Access Memory
RAT Radio Access Technology
RB Resource Block
RCU Radio Control Unit
RET Remote Electrical Tilt
RF Radio Frequency
RLC Radio Link Control
RRC Radio Resource Control
RRM Radio Resource Management
RRU Remote Radio Unit
RS Reference Signal
RSRP Reference Signal Received Power
RSRQ Reference Signal Received Quality
RSSI Received Signal Strength Indicator
RTT Round Trip Time
RV Redundancy Version
Rx Receive
S1 interface between EPC and E-UTRAN
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
78
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
79
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
SBT Smart Bias Tee
SC-FDMA Single Carrier-Frequency Division Multiple Access
SCTP Stream Control Transmission Protocol
SDH Synchronous Digital Hierarchy
SFBC Space Frequency Block Coding
SFP Small Form – factor Pluggable
SGW Serving Gateway
SIB System Information Block
SID Silence Indicator
SINR Signal to Interference plus Noise Ratio
SRB Signaling Radio Bearer
SRS Sounding Reference Signal
SSL Security Socket Layer
STBC Space Time Block Coding
STMA Smart TMA
TAC Transport Admission Control
TCP Transmission Control Protocol
TDD Time Division Duplex
TMA Tower Mounted Amplifier
TMF Traced Message Files
ToS Type of Service
TTI Transmission Time Interval
Tx Transmission
UE User Equipment
UL-SCH Uplink Shared Channel
USB Universal Serial Bus
U2000 Huawei OMC
VLAN Virtual Local Area Network
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
80
eLTE2.3eLTE2.3 DBS3900 LTE FDD Basic Feature Description 2 Acronyms and Abbreviations
VoIP Voice over IP
WRR Weighted Round Robin
X2 interface among eNodeBs
Issue Draft A (2014-02-10) Huawei Proprietary and Confidential Copyright © Huawei
Technologies Co., Ltd.
81