Cisco TelePresence Endpoint
Technical Handbook
Technical Support Guide
D14484.10
February 2011
Contents
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 2 of 40
Contents Document revision history .................................................................................................... 4
Introduction ............................................................................................................................ 5
Information on service request ............................................................................................. 6
Terminal software for TelePresence Endpoint .................................................................... 7 Windows HyperTerminal (Serial, Telnet) ......................................................................................... 7 TeraTerm .......................................................................................................................................... 7 Putty (Serial, Telnet, SSH) ............................................................................................................... 7 How to use Windows Hyper Terminal .............................................................................................. 8 How to use TeraTerm ....................................................................................................................... 9 How to use Putty ............................................................................................................................ 10
File transfer software for TelePresence Endpoint ............................................................ 11 Command Prompt .......................................................................................................................... 11 WinSCP .......................................................................................................................................... 11 How to use Windows Command Prompt ....................................................................................... 12 How to use WinSCP ....................................................................................................................... 13
Sniffer software for TelePresence Endpoint ...................................................................... 14 Wireshark (IP packet sniffer) .......................................................................................................... 14
RS-232 Serial Connection .................................................................................................... 15
How to capture a log from TelePresence C/EX-series Endpoint ..................................... 16 IP issues (H323) ............................................................................................................................. 16 IP issue (SIP) ................................................................................................................................. 16 Reboot Issue .................................................................................................................................. 17 Basic network status check from C/EX-series Endpoint ................................................................ 17 Sniffer the packet on C/EX-Series Endpoint .................................................................................. 17 How to de-activate audio/video protocol in C/EX-series Endpoint ................................................. 17 Default factory C/EX-series Endpoint ............................................................................................. 17 Revert back previous software version on C/EX-series Endpoint.................................................. 18 Reset Password on C/EX-Series Endpoint .................................................................................... 19 Monitor diagnostic for RMA ............................................................................................................ 19
How to upgrade TelePresence C/EX-series Endpoint software ....................................... 20
How to capture a log from TelePresence T3/T1 Immersive System ................................ 21 Retrieving Log from each C90 codec in T3/T1 Immersive System ................................................ 21 Retrieving Log from TelePresence Control Unit (TCU) - From external PC .................................. 21 Retrieving Log from TelePresence Control Unit (TCU) - Directly from TCU .................................. 21 Revert back previous software version on TCU ............................................................................. 22
How to upgrade TelePresence T3/T1 Immersive System software ................................. 23 Upgrade C90 codec in T3/T1 Immersive System .......................................................................... 23
Contents
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 3 of 40
Upgrade TelePresence Control Unit (TCU) – by using SCP software ........................................... 23 Upgrade TelePresence Control Unit (TCU) – by using USB memory stick ................................... 24
How to capture a log from TelePresence E20 Endpoint ................................................... 26 IP issue (SIP) ................................................................................................................................. 26 Reboot Issue .................................................................................................................................. 26 Basic network status check from E20 Endpoint ............................................................................. 26 How to de-activate audio/video protocol in E20 Endpoint .............................................................. 27 Default factory E20 Endpoint.......................................................................................................... 27 Revert back previous software version on E20 Endpoint .............................................................. 27
How to upgrade TelePresence E20 Endpoint software .................................................... 28
How to capture a log from MXP series Endpoint .............................................................. 29 IP issues (H323/SIP) ...................................................................................................................... 29 ISDN Issues ................................................................................................................................... 29 Reboot Issue .................................................................................................................................. 29 Default factory MXP Endpoint ........................................................................................................ 30 Revert back previous software version on MXP Endpoint ............................................................. 30 Monitor diagnostic for RMA ............................................................................................................ 31
How to upgrade MXP series Endpoint software ................................................................ 32
How to capture a log from Classic series Endpoint ......................................................... 33 IP issues ......................................................................................................................................... 33 ISDN Issues ................................................................................................................................... 33 Reboot Issue .................................................................................................................................. 34 Default factory Classic Endpoint .................................................................................................... 34 Revert back previous software version on Classic Endpoint ......................................................... 34
How to upgrade Classic series Endpoint software ........................................................... 36
How to capture a log from TelePresence Movi .................................................................. 37 Retrieving the Movi log from PC .................................................................................................... 37 Sniffer the Movi signal and payload from PC - Preparation ........................................................... 37 Sniffer the Movi signal and payload from PC ................................................................................. 38
Document revision history
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 4 of 40
Document revision history
Revision Date Description
D14484.09 February 2011 - Reformat from TP Solution Support – APAC TP Endpoint Handbook Rev 1.8 version.
- Add T3/T1 Immersive System Information - Update commands for C/EX-series Endpoint
D14484.10 February 2011 - Add T3/TCU Immersive System Information
Introduction
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 5 of 40
Introduction Each system will be provided with its own User Guide, Quick Reference Guide and if needed, an installation manual. This document is quick reference handbook for basic troubleshooting to ensure to have same understanding of basic troubleshooting method on Cisco TelePresence Endpoint.
Information on service request
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 6 of 40
Information on service request To ensure Cisco TelePresence TAC to assist technical service request and provide quick resolution, TelePresence TAC require a minimum amount of information for each service request.
When reporting the technical service request, please ensure:
Describe in detail about problem/issue
Describe how often the problem occurs
Describe the latest operation before problem occurs, if any
Describe in detail, procedure to recreate the problem, if any
Describe in detail, which steps have already been taken in investigating the problem
Describe the equipment used and the system serial number (from all sites involved)
Describe the software version of system (from all sites involved)
Logs from system including configuration and system status
Terminal software for TelePresence Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 7 of 40
Terminal software for TelePresence Endpoint Important: Please start the log capture from all systems involved in the call before calls/conferences are started so we capture all the call setup process and ensures that all output is logged to a file so none is lost.
There is multiple terminal software that may use for retrieving the log from system:
Windows HyperTerminal (Serial, Telnet) Can be found under: Start Menu – All Programs – Accessories – Communications – HyperTerminal. The Windows Hyper Terminal supports the Telnet protocol only. Please remember to enable the Capture Text option (menu “Transfer” – “Capture Text”).
TeraTerm Down load the TeraTerm installation file from http://sourceforge.jp/projects/ttssh2/releases/ Supports multiple Protocols, including Telnet and SSH which are the two relevant protocols for the TelePresence Endpoint portfolio. It will automatic detect serial port if you are using USB to serial converter and option for save log with time stamp.
Putty (Serial, Telnet, SSH) Download the Putty installation file from http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Supports multiple Protocols, including Telnet and SSH which are the two relevant protocols for the TelePresence Endpoint portfolio.
Cisco Te
How toThis folloPlease n
1. S
2.
3.
Note
4. Ts
5. T
elePresence S
o use Windowing page enote, Window
Start Hyper THyperTerminUnder “Conn
Default passhave “admine: C-series a
default. To save retrisave it as a *Type in the r
Solution Supp
dows Hypexplains howws Vista and
Terminal: Stanal Supportsnect using” s
sword is ciscon” or “root” asand EX-series
ieve logs: En*.log file. respective co
port – TelePres
per Terminw to use Wind
Windows 7
art Menu – A the Telnet pelect “TCP/IP
o, TANDBERs login names Endpoint w
nable the Ca
ommands de
sence Endpoi
nal dows Hyper may not hav
All Programs protocol onlyP (Winsock)
RG or blank .
with TC4.0.0
pture Text o
escribed in A
Termina
nt Handbook
Terminal. ve Hyper Ter
– Accessori. ” and enter t
unless chang
or newer sof
ption (menu
Appendix.
l software for
minal installe
es – Commu
he System IP
ged. Some E
ftware, root a
“Transfer” –
TelePresence
Pa
ed on defaul
unications –
P address.
Endpoint pro
account is di
– “Capture Te
e Endpoint
age 8 of 40
t setting.
ducts
sable by
ext”), and
Cisco Te
How toThis follo
1. S
2. S(c
3.
Note
4. T
c(
5. T
elePresence S
o use Teraowing page e
Start TeraTeinstall softwaSelect “Telne(Or select “Sconnection b
Default passhave “admin
e: C-series adefault.
To save retriname. You mclock informa(Example of
Type in the r
Solution Supp
aTerm explains how
erm: Start Meare as defaulet” and enter
SSH” and entbetween syst
sword is ciscon” or “root” as
and EX-series
ieve logs: Semay check “Tation. timestamp f
respective co
port – TelePres
w to use Tera
enu – All Prolt setting). r the Systemter the Systetems.)
o, TANDBERs login name
s Endpoint w
elect “Log” froTimestamp” o
ormat on log
ommands de
sence Endpoi
aTerm.
ograms – Ter
m IP addressem IP addres
RG or blank .
with TC4.0.0
om File menoption which
g: [Wed Feb 2
escribed in A
Termina
nt Handbook
raTerm Pro w
in “Host”. ss in “Host” in
unless chang
or newer sof
nu and selecth will add time
25 15:10:30
Appendix.
l software for
with TTSSH2
n order to es
ged. Some E
ftware, root a
t location of sestamp on lo
2009]).
TelePresence
Pa
2 – TeraTerm
stablish SSH
Endpoint pro
account is di
saving file anog base on P
e Endpoint
age 9 of 40
m Pro (if
ducts
sable by
nd file PC’s
Cisco Te
How toThis follo
1. S2. S
(c
3.
4. Ts
Note
5. T
elePresence S
o use Puttowing page e
Start Putty Select “Telne(Or select “Sconnection b
Default passhave “adminTo save retrisaving file an
e: C-series adefault.
Type in the r
Solution Supp
ty explains how
et” and enterSSH” and entbetween syst
sword is ciscon” or “root” asieve logs: Send file name
and EX-series
respective co
port – TelePres
w to use Putty
r the Systemter the Systetems.)
o, TANDBERs login nameelect “Logginat “Log file n
s Endpoint w
ommands de
sence Endpoi
y.
m IP addressem IP addres
RG or blank .
ng” and chooname”.
with TC4.0.0
escribed in A
Termina
nt Handbook
in “Host Namss in “Host N
unless chang
se “All sessio
or newer sof
Appendix.
l software for
me”. ame” in orde
ged. Some E
on output” an
ftware, root a
TelePresence
Pag
er to establis
Endpoint pro
nd select loc
account is di
e Endpoint
ge 10 of 40
h SSH
ducts
cation of
sable by
File transfer software for TelePresence Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 11 of 40
File transfer software for TelePresence Endpoint There is multiple file transfer software that may use for retrieving the log from system or/and uploading file to system:
Command Prompt Can be found under: Start Menu – All Programs – Accessories – Command Prompt. Command Prompt support ftp base file transfer between local PC and TelePresence Endpoint.
WinSCP Download the WinSCP installation file from http://winscp.net/eng/index.php Support SCP protocol with GUI for Windows base PC which use for safely copying of file between local PC and TelePresence Endpoint. (Newer TelePresence Endpoint only supports SCP for file transform, not FTP).
Cisco Te
How toThis follo
1. SC
2. c
3. 4.
5.
6. T
elePresence S
o use Windowing page e
Start CommaCommand P
Navigate loccommand. For exampleEstablish ftpDefault passhave “adminBasic comm
o ls – liso cd – uo terminate f
port – TelePres
mmand Prw to use Com
Hyper Termitart Menu – R
ving downloa
ownload log by using “ftpo, TANDBERs login name
will use on ftpectory
navigate to ting “#” for ea
y transfer modownload speupload specifftp session b
sence Endpoi
rompt mmand Prom
inal: Start MeRun… - type
ad file or file f
to log folderp ” commandunless chang
rectory/folderansferred
om codec to odec from PCec and PC
r software for
ograms – Accclick “ok”)
to upload to
ve on PC, “cdd. ged. Some E
r
PC C
TelePresence
Pag
cessories –
system by u
cd C\log”.
Endpoint pro
e Endpoint
ge 12 of 40
using “cd”
ducts
Cisco Te
How toThis follo
1. Ss
2. Sa
Note
3. A
4. s
elePresence S
o use WinSowing page e
Start WinSCsetting). Select “SCPand system Default pass
e: C-series adefault.
After verifyinIf the error m
Find the log side of GUI w
Solution Supp
SCP explains how
CP: Start Men
” as Protocopassword in
sword is cisco
and EX-series
ng the informmessage belo
file that wouwindows whi
port – TelePres
w to use WinS
nu – All Prog
l, enter the S“Password”.o, TANDBER
s Endpoint w
ation click onow appear du
ld like to retrch is your lo
sence Endpoi
SCP
rams – WinS
System IP ad. RG or blank
with TC4.0.0
n “Login”. uring the con
rieve from rig
ocal PC
File transfe
nt Handbook
SCP – WinSC
ddress in “Ho
unless chang
or newer sof
nnection proc
ght side of G
r software for
CP (if install
ost name”, “ro
ged.
ftware, root a
cess, just clic
UI windows a
TelePresence
Pag
software as
root” in “User
account is di
ck “OK” and
and drag it to
e Endpoint
ge 13 of 40
default
r name”
sable by
proceed.
o left
Sniffer software for TelePresence Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 14 of 40
Sniffer software for TelePresence Endpoint Important: Please start the log capture from all systems involved in the call before calls/conferences are started so we capture all the call setup process and ensures that all output is logged to a file so none is lost.
There is multiple sniffer software that may use for retrieving the log from system:
Wireshark (IP packet sniffer) Download the Wireshark installation file from http://www.wireshark.org/download.html Wireshark is the network protocol analyzer, and is standard across industries.
RS-232 Serial Connection
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 15 of 40
RS-232 Serial Connection Most of TelePresence Endpoint has the D-Sub 9 pin data port on the back of the unit that may be used for configuration and administration. The data port may also use for initial configuration. Software upgrades may also be monitored via the serial ports.
Any RS-232 emulation can be used, such as Microsoft HyperTerminal, TeraTerm, etc. The default connectivity parameters are:
Model Parameter
Classic Endpoint MXP Endpoint
Baud Rate 9600 bps
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
Model Parameter
C-SeriesEndpoint * EX90/EX60 and C20 required special console adapter
Baud Rate 38400 bps
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
Model Parameter
E20 Endpoint * required special console adapter
Baud Rate 115200 bps
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
How to capture a log from TelePresence C/EX-series Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 16 of 40
How to capture a log from TelePresence C/EX-series Endpoint Important: Please start the log capture from all systems involved in the call before calls/conferences are started so we capture all the call setup process and ensure that all output is logged to a file so none is lost.
This chapter explains how to capture the complete log file available for TelePresence C-series and EX-series Components.
The table below lists the commands needed for the TelePresence C-series and EX-series Endpoint. Please type all commands in the same Telnet/SSH session.
All retrieved logs should attach to ticket including a description and compress multiple attachments into one file.
IP issues (H323) Commands in bold
Open the console/telnet/ssh session with codec Reboot codec by xCommand boot Reopen the console/telnet/ssh session with codec xstatus xconfig log ctx H323Packet debug 9 (TC2.x or prior software version, please use “log ctx
H323Stack debug 9”) Make a call and keep running until you have recreated the problem xstatus, if issue related to video/audio channel status etc. Hang up call log ctx H323Packet debug off (TC2.x or prior software version, please use “log ctx
H323Stack debug off”) Once recreated the problem and captured the log, reboot codec by xCommand boot Access to codec WebGUI for download log file, http:// Download the latest file “log.tar.gz” Attach file to the ticket – Remember to name these or include a description and compress
multiple attachments into one file Important: Tracing MUST be turned off when done. It’s not recommended to let the tracing stay on when the system is used in production.
IP issue (SIP) Commands in bold
Open the console/telnet/ssh session with codec Reboot codec by xCommand boot Reopen the console/telnet/ssh session with codec xstatus xconfig log ctx SipPacket debug 9 Make a call and keep running until you have recreated the problem xstatus, if issue related to video/audio channel status etc. Hang up call log ctx SipPacket debug off Once recreated the problem and captured the log, reboot codec by xCommand boot Access to codec WebGUI for download log file, http:// Download the latest file “log.tar.gz” Attach file to the ticket – Remember to name these or include a description and compress
multiple attachments into one file
How to capture a log from TelePresence C/EX-series Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 17 of 40
Important: Tracing MUST be turned off when done. It’s not recommended to let the tracing stay on when the system is used in production.
Reboot Issue After codec restart Access to codec WebGUI for download log file, http:// Download the latest file “log.tar.gz” Attach file to the ticket – Remember to name these or include a description and compress
multiple attachments into one file
Basic network status check from C/EX-series Endpoint Commands in bold
Open the console/ssh session with codec and login as “root” user ping , check reachability netstat eth0, current connected ports on codec netstat -rn, current network routing on codec
Sniffer the packet on C/EX-Series Endpoint Note: Require TC2.0 or newer software version Note: This method should only use when request by TelePresence TAC. Important: This works on both H.323 and SIP call, however it must disable encryption. For SIP, make sure not to use TLS for signaling. Commands in bold
Open the console/ssh session with codec and login as “root” user tcpdump –n –s 1500 –w /tmp/tcpdump.pcap ip and not port 22 Make a call and keep running until you have recreated the problem Ctrl + C Open WinSCP and reteieve the sniffer log under /tmp directory. Attach file to the ticket – Remember to name these or include a description and compress
multiple attachments into one file Important: Tracing log MUST delete as tmp folder has limited desk space and not design to
capture log. Note: Make sure to retrieve sniffer log before restarting codec. Sniffer log saved in /tmp directory
will be erased after restart codec.
How to de-activate audio/video protocol in C/EX-series Endpoint C-series Endpoint support CapSet filter feature useful for connection between legacy system, interop testing, etc. Sample of CapSet filter commands;
To force G.722.1 -> disable all other: xConfig Experimental CapsetFilter: AAC-LD;G.722;G.711a;G.711mu;G.729AB;G.729;G.729A
To force H.263 -> disable H.264 xConfig Experimental CapsetFilter: H.264;H.264RCDO;H.264NIL
To force H.261 -> disable H.264 and H.263 xConfig Experimental CapsetFilter: H.264RCDO;H.264NIL;H.263;H.263PP
To reset CapSet filter xConfig Experimental CapsetFilter: ""
Default factory C/EX-series Endpoint Commands in bold
Open the console/ssh session with codec and login as “root” user rm /mnt/base/active/config.db, this remove the current configuration file from Codec reboot
Cisco Te
O xNoteWinS
If EX-ser
t
RevertComman
a
T
C
C Alter C T
C
C
elePresence S
or Open the coxCommande: You may hSCP, naviga
ries EndpoinUnplug poweRe plug powImmediately the power buPush the pow
t back prevnds in bold Login as rooavailable whExecute the The Codec w
Check feedb[SELECTEDReboot the sCodec will a
rnative methConnect a seReboot the sPress c to stExecute the The Codec w
Check feedb[SELECTEDReboot the sCodec will a
Solution Supp
nsole/ssh se systemunithave configuate to the fold
nt is not acceer cable
wer cable when the gr
utton for 10 swer button tw
vious soft
ot, i.e., ssh rohen connectin
command: swill now list th
back and seleD]”) or selectssystem, reboutomatically
od for reverterial cable tosystem, and top auto boocommand: s
will now list th
back and seleD]”) or selectssystem, bootutomatically
port – TelePres
ession with ct FactoryResration back u
der: ‘/mnt/bas
ssible or reb
reen led in thseconds (thewice within tw
tware vers
oot@ or usfrom console
es and tell yo
electsw ima(if feedback
previous sw
are by changat 38400, 8,see Press 'b
URN> promp
es and tell yo
electsw ima(if feedback
previous sw
ure a log from
nt Handbook
gin as “adminm: Yes
ing config.dbnd copy the f
power switch
ft corner of th off), until the(two short pu
/EX-series
e ssh termine).
ou which one
age1 (if feedbis “image2 [
version of C
ing the boot , N, 1 b' to enter u-bpt will return.
ou which one
age1 (if feedbis “image2 [A
version of C
m TelePresenc
n” user
b file. Log in file ‘config.db
for factory d
he EX90 lighte green led lushes)
s Endpoin
al software (
e is active
back is “imagACTIVE] [SE
odec had
configuration
boot messag
e is active
back is “imagACTIVE] [SE
odec had
ce C/EX-series
Pag
as root usingb’ to your loc
default
ts up, press ights up aga
t
(same metho
ge2 [ACTIVEELECTED]”)
n
ge
ge2 [ACTIVE
ELECTED]”)
s Endpoint
ge 18 of 40
g al PC.
and hold ain.
od
E]
E]
Cisco Te
Reset Comman
C
C S
<
Monito
f
elePresence S
Passwordnds in bold Connect a seReboot the sLog in with thLogging in w
Change to ESet a new ad
or diagnosPlease downfollow the ma
Solution Supp
d on C/EX-
erial cable tosystem, powehe user "PW
with this user
Endpoint Opedmin passwo>
stic for RMnload latest manual come t
port – TelePres
-Series En
o the system er cycle
WREC". This will reset the
eration modeord, xComm
MA monitor diagntogether with
How to capt
sence Endpoi
ndpoint
at 38400, 8,
user is only e password o
e, tsh mand System
nostic tool anh tool.
ure a log from
nt Handbook
, N, 1
available a sof the root us
mUnit Admin
nd reporting
m TelePresenc
short period oser
nPassword S
template fro
ce C/EX-series
Pag
of time after
Set Passwo
m partner sit
s Endpoint
ge 19 of 40
reboot.
ord:
te and
Cisco Te
HowEndThis chacase of p Comman
O
W S W
l x r
elePresence S
w to uppoint
apter explainsproblem with
nds in bold Open WinSCUpload softwNote: SW file
Wait for comSW upgradeWait for comlogin as “admxCommandreboot syste
Solution Supp
pgradesoftws how to upg
h upgrading s
CP and estabware under /ue name shou
mpletion of filee automaticalmpletion of somin” user SystemUnim, xComma
port – TelePres
e Teleware
grade C-seriesoftware from
blish the conupgrade folduld rename t
e transfer. lly start after
oftware upgra
t ReleaseKeand boot
How to upg
sence Endpoi
Prese
es and EX-sem WebGUI o
nnection with er to “pkg” befo
r completion ade then ope
ey Add Key
grade TelePres
nt Handbook
nce C
eries Endpoir TMS.
codec
re upload it t
of file transfeen the conso
:
series Endpoin
Pag
eries
SCP softwar
on with code
nt software
ge 20 of 40
e for in
ec and
Cisco Te
HowImmImportaare startnone is l
This chaImmersiv
All retrieinto one
RetrievPlease r
RetrievThe TCUsystem a
A
A
RetrievThe TCUsystem a
C T
bd
W
elePresence S
w to camersive
nt: Please stted so we calost.
apter explainsve System.
ved logs shofile.
ving Log frefer “How to
ving Log fU logs shouldand its variouAccess TCUUser name is
Download loAttach file tomultiple atta
ving Log fU logs shouldand its variouConnect the The logs arebe saved to drive is inserWith KeyboaManager win
Solution Supp
apturee Systtart the log cpture all the
s how to cap
ould attach to
from eacho capture a lo
from TelePd be captureus componen
U web via HTs admin and
og, configurato the ticket – chments into
from TelePd be captureus componenkeyboard an
e stored on tha USB thumrted into the ard and mousndow.
Ho
port – TelePres
a log tem capture from call setup pr
pture the com
o ticket includ
C90 codeog from C/EX
Presence d for any issnts. TPS, select no passwor
tion and statRemember t
o one file
Presence d for any issnts. nd Mouse to he E drive at b drive. The TCU, it will bse connected
ow to capture
sence Endpoi
from
all systems rocess and e
mplete log file
ding a descr
ec in T3/T1X-series End
Control Uue regarding
the respectivrd in default
tus files to name thes
Control Uue regarding
the TCU viat the followingUSB thumb
be seen as thd, press the
a log from Te
nt Handbook
TeleP
involved in thensure that a
e available fo
iption and co
1 Immersipoint” chapte
Unit (TCU)g the Cisco T
ve log as per
se or include
Unit (TCU) g the Cisco T
a the USB pog path: E:/tadrive should
he F:/ drive. Ctrl+Shift+E
lePresence T3
resen
he call beforell output is lo
or TelePrese
ompress mul
ve Systemer
- From exTelePresence
r date and tim
e a descriptio
- Directly TelePresence
orts. ndberg/logs
d be 2 GB or
Esc keys to o
3/T1 Immersiv
Pag
ce T3/
e calls/confeogged to a fil
ence T3/T1
ltiple attachm
m
xternal PCe T3/T1 Imm
me of proble
on and comp
from TCUe T3/T1 Imm
s. These logr larger. Whe
open the Tas
ve System
ge 21 of 40
/T1
erences e so
ments
mersive
m
ress
U mersive
s should en the
sk
How to capture a log from TelePresence T3/T1 Immersive System
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 22 of 40
Select File, then New Task. Type explorer in the field Navigate to E:/tandberg/logs Sort the files by date Save all files with the same date as the incident. Attach file to the ticket – Remember to name these or include a description and compress
multiple attachments into one file
Revert back previous software version on TCU Connect the keyboard and Mouse to the TCU via the USB ports. Press CTRL+ALT+DEL to restart the TCU When TCU is restarting, continue to press the keyboard key F8 You will see a screen , current booting image is high lighted
option 1 – Windows XP embedded 1 option 2 – Windows XP embedded 2
Select other image by up / down arrow. TCU will then boot up with the old software
Cisco Te
HowSystThis cha
UpgradPlease r
UpgradComman
O
W O
e
Oc
elePresence S
w to uptem so
apter explains
de C90 corefer “How to
de TelePrends in bold Open WinSCUser Name iUpload softw
Wait for comOpen the ssUser Name iExecute softe:/tandbergImage_name
Once all upgconsole.
Solution Supp
pgradeoftwars how to upg
odec in T3/o upgrade C/
esence Co
CP and estabis Administra
ware under /c
mpletion of fileh session wiis Administratware upgrad/upgrade/ me
sfully, “Every
e TelePresenc
nt Handbook
nce T3
System by us
tem ware” chapte
by using S
TCU d is tec unles
pgrade folder
d is tec unles/upgrade.sh
ything is ok“m
ce T3/T1 Imm
3/T1 Im
sing SCP sof
r
SCP softw
ss changed. r
ss changed.
message prom
mersive System
Pag
mmers
ftware.
ware
mpt back on
m software
ge 23 of 40
sive
SSH
Cisco Te
r T
UpgradRequirem
2 T
Preparat
c
S C C
UpgradinComman
T A
elePresence S
reboot systeTCU boot up
de TelePrement 2 GB or largThe TCU sof
tion - USB m
Download livcreator/liveuDownload Fehttp://archiveLive-KDE.isoInsert the USFormat the UUnzip and stBrowse for thSelect a PerPress CreateCreate a foldPut the imagPut the updaDouble click Copy all the
ng the TCU snds in bold Turn off TCUInsert USB mAttached a UPower on TCHe BIOS mu
Solution Supp
m, C:/tandbp with new so
esence Co
er USB memftware image
memory stick
veusb-creatosb-creator-2edora softwaes.fedoraprojo SB memory sUSB memorytart the liveushe Fedora ISrsistent Storae Live USB der named tage.zip file intate scripts intthe image.zfiles in this f
software
U memory stickUSB keyboarCU ust be set up
H
port – TelePres
berg/scripts/oftware versi
ontrol Uni
mory stick e file must be
or software fr.7.zip (doesn
are, Fedora-9ject.org/pub/
stick in the Py stick (FAT1sb-creator soSO image age of 500MB
andberg in thto the tandbeto the tandbzip and openolder to the t
k in TCU rd to the TCU
to boot from
How to upgrad
sence Endpoi
/reboot.bation
t (TCU) –
e zipped (in t
rom https://fen’t have to be9-i686-Live-K/archive/fedo
PC 1/T32) oftware
B (use arrow
he root of theerg folder
berg folder n the tandbetandberg fol
U
m USB
e TelePresenc
nt Handbook
by using U
this example
edorahosted.e latest versiKDE.iso, ora/linux/rele
w keys to get
e USB memo
erg/scripts folder on the U
ce T3/T1 Imm
USB mem
, refer to it a
org/releasesion of liveusb
ases/9/Live/i
the exact siz
ory stick
older USB memory
mersive System
Pag
mory stick
as image.zip)
s/l/i/liveusb-b-creator)
i686/Fedora-
ze)
y stick
m software
ge 24 of 40
)
-9-i686-
How to upgrade TelePresence T3/T1 Immersive System software
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 25 of 40
Stop the boot process by pressing Delete key Change boot order to USB as first order (noted the original boot configuration first) Save changes and exit from BIOS setting menu Log in as root after system boot up (with Fedora Linux), no password by default Execute, mkdir stick Execute, mount /dev/sdbl stick Execute, cd stick/tandberg/ Execute, ./setup.sh /dev/sda ./ Execute, cd .. Execute again, cd .. Remove the USB memory stick Turn off TCU by switch off the power Power the TCU back on Enter BIOS again and change back boot order to original configuration Save changes and exit from BIOS setting menu
Cisco Te
HowEndImportaare startnone is l
This chaCompon
The tablecomman
All retrieinto one
IP issuComman
O x x x O A C A
Impoon w
Reboo A C A
Basic nComman
O
elePresence S
w to capoint nt: Please stted so we calost.
apter explainsnents.
e below listsnds in the sam
ved logs shofile.
ue (SIP) nds in bold Open the coReboot codeReopen the xstatus xconfig log ctx SipPMake a call axstatus, if isHang up calllog ctx SipPOnce recreaAccess to coClick the “logAttach file tomultiple atta
ortant: Tracwhen the sys
ot Issue After codec rClick the “logAttach file tomultiple atta
network snds in bold Open the coping , chec0, current concurrent netw
port – TelePres
a log
capture from call setup pr
pture the com
nds needed fSH session.
o ticket includ
/ssh session mand bootet/ssh sessio
ug 9 nning until yoto video/aud
ug off lem and cap
UI for downlodownload “latRemember t
o one file
e turned off win production
ss to codec Wdownload “LaRemember t
o one file
ck from E
ession with cck reachabilinnected port
work routing o
How
sence Endpoi
from
all systems rocess and e
mplete log file
for the TeleP
ding a descr
with codec
on with code
ou have recrio channel s
ptured the logoad log file, htest.log” fileto name thes
when done. In.
WebGUI for atest. log” fileto name thes
E20 Endpo
codec and logity ts on codecon codec
w to capture a
nt Handbook
TeleP
involved in thensure that a
e available fo
Presence E2
iption and co
ec
eated the protatus etc.
g, reboot codhttp://
on and comp
let the tracin
ress
Cisco Te
How toE20 Endtesting, eSample
T
T
T
T
DefaulComman
O NoteWinS
RevertCommanIf you ha
T
C
C
If you
l C
s
elePresence S
o de-activadpoint suppoetc. of CapSet filTo force G.7
xConfig ELD;G.722
To force H.2xConfig E
To force H.2 xConfig E
To reset Ca xConfig E
t factory Ends in bold Open the corm /mnt/basreboot e: You may hSCP, naviga
t back prevnds in bold ave ssh connLogin as rooExecute the The Codec w
Check feedb[SELECTEDReboot the sCodec will au have no remHold down thled on top ofClick the butsecond click
Solution Supp
ate audio/rt CapSet filt
lter comman722.1 -> disaExperimenta;G.711a;G.7
263 -> disableExperimenta261 -> disableExperimentapSet filter Experimenta
E20 Endpo
nsole/ssh sese/active/co
have configuate to the fold
vious soft
nection ot, i.e., ssh ro
command: swill now list th
back and seleD]”) or selectssystem, reboutomatically mote accesshe buttons '4f the E20 statton '4' twice
k)
port – TelePres
/video proter feature us
ds; ble all other:
al CapsetFilt711mu;G.729e H.264 al CapsetFilte H.264 and al CapsetFil
al CapsetFil
oint
ession with cnfig.db, this
ration back uder: ‘/mnt/bas
tware vers
oot@
Cisco Te
HowsoftThis chaupgradin Comman
O
W S W
l r
elePresence S
w to upware
apter explainsng software f
nds in bold Open WinSCUpload softwNote: SW file
Wait for comSW upgradeWait for comlogin as “admreboot syste
Solution Supp
pgrade
s how to upgfrom WebGU
CP and estabware under /ue name shou
mpletion of filee automaticalmpletion of somin” user m, xComma
port – TelePres
e Tele
grade E20 EnUI or TMS.
blish the conupgrade folduld rename t
e transfer. lly start after
oftware upgra
and boot
How
sence Endpoi
Prese
ndpoint by us
nnection with er to “pkg” befo
r completion ade then ope
w to upgrade T
nt Handbook
nce E2
sing SCP so
codec
re upload it t
of file transfeen the conso
TelePresence
20 End
ftware for in
to codec.
er ole/ssh sessio
e E20 Endpoin
Pag
dpoin
case of prob
on with code
nt software
ge 28 of 40
t
blem with
ec and
How to capture a log from MXP series Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 29 of 40
How to capture a log from MXP series Endpoint Important: Please start the log capture from all systems involved in the call before calls/conferences are started so we capture all the call setup process and ensure that all output is logged to a file so none is lost.
This chapter explains how to capture the complete log file available for MXP Components.
The table below lists the commands needed for the MXP series Endpoint. Please type all commands in the same Telnet/SSH session.
All retrieved logs should attach to ticket including a description and compress multiple attachments into one file.
IP issues (H323/SIP) Commands in bold
Open the console/telnet/ssh session with codec xstatus xconfig syslog 3 Make a call and keep running until you have recreated the problem xstatus, if issue related to video/audio channel status etc.
Don't worry that the screen is scrolling, just type in and press return to retrieve system status log
Hang up call syslog off
Don't worry that the screen is scrolling, just type in and press return to turn off logging
ISDN Issues Commands in bold
Open the console/telnet/ssh session with codec xstatus xconfig syslog 3 isdn on Make a call and keep running until you have recreated the problem xstatus, if issue related to video/audio channel status etc.
Don't worry that the screen is scrolling, just type in and press return to retrieve system status log
Hang up call syslog off
Don't worry that the screen is scrolling, just type in and press return to turn off logging isdn off dumph221
Reboot Issue Commands in bold
After codec restart open the console/telnet/ssh session with codec eventlog
or Download event. log file from root directory of Codec Open Command prompt (and change home directory, if necessary) ftp Default password is TANDBERG unless changed. Some Endpoint products have “admin” or
“administrator” as login name. hash
Cisco Te
g T A
DefaulComman
O T x
O T C “
e q C
RevertComman
O T C “
s W q C
elePresence S
bin get event.lobye The event. loAttach file tomultiple atta
t factory Mnds in bold Open the coTake backupxCommand
or Open the coTake backupRestart codeCtrl + Break“$” prompt w
eee q Codec will a
t back prevnds in bold Open the coTake backupRestart codeCtrl + Break“$” prompt w
selectsw Wait for “ActIf x = 1, thenIf x = 2, thenq Codec will a
Solution Supp
og
og file transfeo the ticket – chments into
MXP Endp
nsole/telnet/p of system c DefaultValu
nsole sessiop of system cec and breakk (for hyper tewill feedback
utomatically
vious soft
nsole sessiop of system cec and breakk (for hyper tewill feedback
tive application selectsw 2n selectsw 1
utomatically
port – TelePres
er to directorRemember t
o one file
point
/ssh session configurationuesSet Leve
on with codecconfigurationk the boot seqerminal), or A
restart
tware vers
on with codecconfigurationk the boot seqerminal), or A
on: x” messa
restart with p
sence Endpoi
ry of Commato name thes
with codecn and option el:3
c by using Rn and option quence Alt + B (for T
sion on M
c by using Rn and option quence Alt + B (for T
age
previous sw
How to cap
nt Handbook
and Prompt sse or include
keys
S232 cablekeys
TeraTerm/Pu
XP Endpo
S232 cablekeys
TeraTerm/Pu
version of C
pture a log fro
specified. e a descriptio
utty)
oint
utty)
odec had
om MXP series
Pag
on and comp
s Endpoint
ge 30 of 40
ress
How to capture a log from MXP series Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 31 of 40
Monitor diagnostic for RMA Please download latest monitor diagnostic tool and reporting template from partner site and
follow the manual come together with tool.
Cisco Te
HowThis chaproblem Comman
O C
f T T
W
elePresence S
w to upapter explains
with upgrad
nds in bold Open CommChange the For exampleftp (or pe, put s50000mpletion of file
codec manua
port – TelePres
e MXPgrade MXP s from WebG
necessary byolder locates
Key in “User:word:”. Defau
put )
GUI, from teln
series Endpoin
Pag
softwfor in case o
tware
changed.
net session,
nt software
ge 32 of 40
ware of
etc.
How to capture a log from Classic series Endpoint
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 33 of 40
How to capture a log from Classic series Endpoint Important: Please start the log capture from all systems involved in the call before calls/conferences are started so we capture all the call setup process and ensure that all output is logged to a file so none is lost.
This chapter explains how to capture the complete log file available for Classic Components.
The table below lists the commands needed for the Classic series Endpoint. Please type all commands in the same Telnet/SSH session.
All retrieved logs should attach to ticket including a description and compress multiple attachments into one file.
IP issues Commands in bold
Open the console/telnet session with codec ati1i4i5i6i7i9 dispparam ipstat netstat syslog on Make a call and keep running until you have recreated the problem statin, if issue related to video/audio channel status etc.
Don't worry that the screen is scrolling, just type in and press return to retrieve system status log
statout, if issue related to video/audio channel status etc. Don't worry that the screen is scrolling, just type in and press return to retrieve system status log
Hang up call syslog off
Don't worry that the screen is scrolling, just type in and press return to turn off logging Attach file to the ticket – Remember to name these or include a description and compress
multiple attachments into one file
ISDN Issues Commands in bold
Open the console/telnet session with codec ati1i4i5i6i7i9 dispparam ipstat netstat syslog on isdn on Make a call and keep running until you have recreated the problem statin, if issue related to video/audio channel status etc.
Don't worry that the screen is scrolling, just type in and press return to retrieve system status log
statout, if issue related to video/audio channel status etc. Don't worry that the screen is scrolling, just type in and press return to retrieve system status log
Hang up call syslog off
Don't worry that the screen is scrolling, just type in and press return to turn off logging isdn off
Cisco Te
d A
RebooComman
A e
O f
“ g T A
DefaulComman
O T x
O T C “
e q C
RevertComman
O T C “
elePresence S
dumph221 Attach file tomultiple atta
ot Issue nds in bold After codec reventlog
or Download evOpen Commftp sword is TANor” as login n
og
og file transfeo the ticket – chments into
Classic En
nsole/telnet/p of system c DefaultValu
nsole sessiop of system cec and breakk (for hyper tewill feedback
utomatically
vious soft
nsole sessiop of system cec and breakk (for hyper tewill feedback
port – TelePres
Remember to one file
the console
from root dir(and change
NDBERG unlname.
er to directorRemember t
o one file
ndpoint
/ssh session configurationuesSet Leve
on with codecconfigurationk the boot seqerminal), or A
restart
tware vers
on with codecconfigurationk the boot seqerminal), or A
sence Endpoi
to name thes
or telnet ses
rectory of Coe home direc
ess changed
ry of Commato name thes
with codecn and option el:3
c by using Rn and option quence Alt + B (for T
sion on Cl
c by using Rn and option quence Alt + B (for T
How to captu
nt Handbook
se or include
ssion with co
odec ctory, if nece
d. Some End
and Prompt sse or include
keys
S232 cablekeys
TeraTerm/Pu
lassic End
S232 cablekeys
TeraTerm/Pu
ure a log from
e a descriptio
odec
ssary)
dpoint produc
specified. e a descriptio
utty)
dpoint
utty)
Classic series
Pag
on and comp
cts have “adm
on and comp
s Endpoint
ge 34 of 40
ress
min” or
ress
Cisco Te
s W q C
elePresence S
selectsw Wait for “ActIf x = 1, thenIf x = 2, thenq Codec will a
Solution Supp
tive application selectsw 2n selectsw 1
utomatically
port – TelePres
on: x” messa
restart with p
sence Endpoi
age
previous sw
How to captu
nt Handbook
version of C
ure a log from
odec had
Classic series
Pag
s Endpoint
ge 35 of 40
Cisco Te
HowsoftThis chaproblem Comman
O C
f T T
W
elePresence S
w to upware
apter explainswith upgrad
nds in bold Open CommChange the For exampleftp (or pe, put s50000mpletion of file
codec manua
port – TelePres
e Clas
grade Classic from WebG
necessary byolder locates
Key in “User:word:”. Defau
put )
GUI, from teln
series Endpoin
Pag
int
re for in case
tware
changed.
net session,
nt software
ge 36 of 40
e of
etc.
Cisco Te
HowImportaare startnone is l
This chaCompon
The tablecomman
All retrieinto one
Retriev T
<
vT
A A
Sniffe Impo
e
S
elePresence S
w to cant: Please stted so we calost.
apter explainsnents.
e below listsnds in the sam
ved logs shofile.
ving the MTotal 6 log fi
o Audio.o Client.o Defauo GStreao TAF.loo SIP.log
File can be f.\Logs\.) PPDATA> fo
E%\Local Se:
ATA% (typica
refer “Trouble
Remember to one file
nd payloadmust disable MS is auto ad off from clieance setting rt protocol.
sence Endpoi
from all systems
rocess and e
mplete log file
for the TeleP
ding a descr
e on local PCfic informatiorelated to theus informatiofrom Gstreamtion framewoabout SIP siglocal PC \Movi\.\TANDB
ally:
cation Data\
PROFILE%\A
ovi” section o
se or include
C - Preparaure not to ussetting tab is
nu
capture a log fr
resenhe call beforell output is lo
or TelePrese
0 Endpoint.
ompress mul
& “Business
rmation
minor versionERG\Movi\<
AppData\Loc
on Cisco Tel
e a descriptio
ation e TLS for sigs available o
rom TelePres
Pag
ce Moe calls/confeogged to a fil
ence Movi
Please type
ltiple attachm
s logic”
n>\Logs\. (M
Cisco Te
T C
Sniffer S S C
elePresence S
If Advance oTMS: Go to Change Enc
r the Movi Start Wire SSelect CaptuClick “Start”
Solution Supp
option is not aSystem – Pr
cryption polic
signal anhark: Start Mure – Interfacon interface
port – TelePres
available on rovisioning, thcy to “Force T
nd payloadMenu – All Prce, from menthat PC is u
sence Endpoi
client then ehen select eTcpNoSrtp”
d from PCrograms – Wnu sing for netw
How to c
nt Handbook
encryption caither specific
Wire shark
work connect
capture a log fr
an be turned c group or clie
tion.
rom TelePres
Pag
off using TMent
ence Movi
ge 38 of 40
MS.
Cisco Te
“r
S
S A
elePresence S
Note: If parti“host ” and click “
nning until yoher Stop Icon
et (packet ranRemember t
o one file
sence Endpoi
et between S“Start”. Only
ou have recrn on menu or
nge should sto name thes
How to c
nt Handbook
IP Server (Vtraffic betwe
eated the pror select Capt
select “All pase or include
capture a log fr
VCS), click “Oeen SIP Serv
oblem ure – Stop, f
ckets”) e a descriptio
rom TelePres
Pag
Option”, then ver sniffer an
from menu
on and comp
ence Movi
ge 39 of 40
type nd file will
ress
How to capture a log from TelePresence Movi
Cisco TelePresence Solution Support – TelePresence Endpoint Handbook Page 40 of 40
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2010 Cisco Systems, Inc. All rights reserved.