Chapter 9 Hyundai
This chapter contains information for testing Hyundai vehicles with the Asian Import Vehicle Communication Software (VCS). The following Hyundai systems may be available for testing:
• Engine• Transmission• Antilock Brake System (ABS)• Airbag (SRS)
9.1 Testing Engine, Transmission, ABS, and SRS SystemsHyundai engine, transmission, and airbag (SRS) testing includes:
• “Code Reading Connectors and Locations” on page 91• “Clearing Codes” on page 93• “Actuator Tests” on page 93
9.1.1 Code Reading Connectors and LocationsRefer to Figure 9-1 below and Table 9-1 on page 92 Hyundai diagnostic connector locations and adapter usage information.
Figure 9-1 Common connector locations
ENGINE
123
91
Testing Engine, Transmission, ABS, and SRS SystemsChapter 9
z To read codes from 1995 and earlier vehicles:
• Use the HYUN-2 adapter (Figure 9-2).
Figure 9-2 Connector and adapter for most OBD-I vehicles
A—Connector
B—HYUN-2 adapter
z To read codes from most 1996 and later vehicles:
• Use the OBD-II adapter with the specified Personality Key™ device (Figure 9-3 on page 93).
NOTE:i Always use the Personality Key™ device specified in the on-screen instructions.
Table 9-1 Common connector locations
VEHICLE YEAR LOCATION
Accent1995–99 2 Above coin holder
2001–05 3 Near hood release
Elantra1992–95 1 In fuse box
1996–05 3 Under dash near steering column
Excel 1990–94 1 In fuse box
Santa Fe 2001–05 1 Behind fuse panel
Scoupe 1991–95 1 In fuse box
Sonata1989–95 1 In fuse box
1996–05 3 Under dash near steering column
Tiburon1997–01 3 Under dash near steering column
2003–05 1 Behind fuse panel
XG300/XG350 2001–05 3 Under dash near steering column
A B
92
Figure 9-3 OBD-II DLC and adapter
A—16-pin DLC
B—Personality Key™ device
C—OBD-II adapter
9.1.2 Clearing CodesMost 1988 and later Hyundai models let you clear trouble codes from PCM memory through the scan tool Exit menu selection CLEAR ECM CODES (Figure 9-4).
Figure 9-4 CLEAR ECM CODES selection
When codes are cleared, the scan tool returns to the previous test mode, and the NO CODES PRESENT message displays to indicate codes are cleared.
If code clearing fails for any reason, the previous codes display at the top of the data list when you return to CODES & DATA. If this happens, repeat code clearing.
9.1.3 Actuator TestsThe ACTUATOR TESTS selection is available from the MAIN MENU (Figure 9-5) for most pre-OBD-II models. All actuator tests are key-on, engine-off tests, except for the injector and timing tests which are explained in “Injector Tests (Engine Running Only)” on page 95.
Figure 9-5 Sample MAIN MENU with ACTUATOR TESTS
A BC
RESUME LED MENUPRINT SCREEN >CLEAR ECM CODESPRINT FRAME FIX LINE 2ARM MOVIE
MAIN MENU--ENGINE OTHER SYSTEMSCODES & DATA(SLOW)CUSTOM SETUP
>ACTUATOR TESTS
93
Testing Engine, Transmission, ABS, and SRS SystemsChapter 9
Selecting ACTUATOR TESTS for these vehicles displays a list of available tests. The list of actuator tests displays similar to Figure 9-6. The available tests vary by year and model.
Figure 9-6 Complete list of Chrysler Imports actuator tests
During testing, monitor the selected actuator with a voltmeter, ammeter, or by listening for actuator activation. A completed test does not mean that the actuator was activated. The scan tool only monitors the engine control module (ECM) commands to the actuator.
When an actuator test is selected, the scan tool commands the ECM to activate the selected actuator (Figure 9-7).
Figure 9-7 Sample actuator test initiated
Approximately 5 seconds later, the ECM deactivates the actuator (Figure 9-8).
Figure 9-8 Sample actuator test complete
NOTE:i All actuator tests except for injector tests must be performed with the key on and engine off
(KOEO). If you select a KOEO test with the engine running, a screen like Figure 9-9 displays.
SCROLL TO SELECT A TEST:5° BTDC TIMING (ENGINE RUNNING ONLY)
>EGR SOLENOID VALVEFUEL PUMPINJECTOR #1 (ENGINE RUNNING ONLY)INJECTOR #2 (ENGINE RUNNING ONLY)INJECTOR #3 (ENGINE RUNNING ONLY)INJECTOR #4 (ENGINE RUNNING ONLY)INJECTOR #5 (ENGINE RUNNING ONLY)INJECTOR #6 (ENGINE RUNNING ONLY)VARIABLE INDUCTION CONTROL SERVODUAL-MODE MUFFLERPRESSURE CONTROL SOL VALVEFUEL PRESSURE SOLENOIDFUEL PUMP RELAY #2PURGE CONTROL SOLENOIDWASTEGATE SOLENOID
ACTIVATING EGR SOLENOID VALVEFOR 5 SECONDS.
EGR SOLENOID VALVETEST HAS BEEN COMPLETED.PRESS Y TO REPEAT TEST.PRESS N FOR ACTUATOR TEST MENU.
94
Figure 9-9 Sample key-on, engine-off test
Injector Tests (Engine Running Only)
The injector tests available from the actuator test menu are performed with the key on and engine running (KOER) and are available on most pre-OBD-II vehicles.
The number of injector tests available varies by the number of cylinders and type of fuel-injection system (a 4-cylinder MPI system has four tests; a six cylinder system has six).
When you select an injector test, the scan tool commands the ECM to disable the selected injector (Figure 9-10).
Figure 9-10 Sample injector test initiated
About 5 seconds later, the ECM stops the test and the injector is re-enabled (Figure 9-11).
Figure 9-11 Sample injector test completed
EGR SOLENOID VALVETEST HAS BEEN REJECTED.PRESS Y TO REPEAT TEST.PRESS NO FOR ACTUATOR TEST MENU.
DISABLING INJECTOR #1FOR 5 SECONDS.
INJECTOR #1 (ENGINE RUNNING ONLY)TEST HAS BEEN COMPLETED.PRESS Y TO REPEAT TEST.PRESS N FOR ACTUATOR TEST MENU.
95