Acqua
shown in Brushed Nickel with metal blades and
decorative guard
shown in Textured Bronze with wood blades
shown in Polished Chrome with wood blades
Designed in 2008
The Acqua rotational ceiling fan is thoughtfully designed to resemble the molecular structure of water, Earth’s most precious resource. The Acqua offers fluid lines and quiet axial rotation. The motor heads can be infinitely positioned in 180-degree arcs for optimum air movement; the greater the angles of the motors to the horizontal support rods (up or down), the faster the axial rotation. A slow, controlled axial rotation is achieved by both motor head position and fan blade speed. Matthews rotational fans circulate heat and air-conditioning more efficiently than traditional paddle fans.
• Available in the following finishes: polished chrome, brushed nickel or textured bronze.• Constructed of cast aluminum and heavy stamped steel, Acqua carries a limited lifetime warranty.• The Acqua is available with the following blade options: • hand-balanced metal blades with decorative metal blade guards • hand-balanced metal blades with metal safety cages for low ceiling applications • hand-balanced solid wood blades without blade guards• The Acqua comes with this standard equipment: • 3-speed remote control • low voltage 50 watt MR-16 GU10 down light • vaulted ceiling canopy
DampLocation:
All Finisheswith
Metal Blades**
Safety cages available for low ceilings.
9"13" 16"
6" diameter
Increasing Angles of Fan Heads to Support Poles Increases Speed of Axial Rotation
Optimum Fan Head Position is 60°
5”, 10", 20", 30", 48" or 72" field cuttable downrods available
2"
5"
39" wood blades / 37" metal blades
Sum
mer
201
3
MATTHEWS F A N C O M P A N Y
Acquaweight: 27 lbsvoltage: 110**Please contact us for possible 220 conversion
The Acqua can be mounted with any one of the following downrod lengths: 5, 10, 20, 30, 48 or 72”. The Acqua is compatible with flat or vaulted ceilings.Safety cages available for low ceiling applications.
**Damp location: All standard finishes with metal blades. Not recommended for salt water / ocean front applications.
**Damp Location1881 Industrial Drive Libertyville, IL 60048 Tele: 847.680.9043 Fax: 847.680.8140 www.matthewsfanco.com
CFM: 4994(Metal Blades)
CFM: 6174(Wood Blades)
SKU Naming Convention
Finishes Blade TypeWood - WD Metal w/ Decorative Cage - MTL Metal w/ Safety Cage - MSAF
Brushed Nickel - BN Polished Chrome - CR Textured Bronze - TB
AQ-XX-XXX (Model-Finish-Blade Type)
DianeDesigned in 2008
The Diane oscillating directional ceiling fan provides maximum, multi-directional airflow. The Diane can be hung in small, awkward spaces or in front of HVAC ducts to make more efficient the heating, ventilation or air conditioning of any room. · The Diane is available in the following finishes: polished chrome, brushed nickel or textured bronze.· Constructed of cast aluminum, and heavy stamped steel, the Diane carries a limited lifetime warranty.· The Diane is available with the following blade options: · hand-balanced metal blades with decorative metal blade guards · hand-balanced metal blades with metal safety cages for low ceiling applications · hand-balanced solid wood blades without blade guards· The Diane is equipped with a 3-speed remote control and vaulted ceiling canopy.
DampLocation:
All Finisheswith
Metal Blades
Safety cages available for low ceilings.
shown in Polished Chrome with metal blades and decorative guard
shown in Textured Bronze with wood blades
shown in Brushed Nickel with wood blades
DampLocation:
All Finisheswith
Metal Blades**
Safety cages available for low ceilings.
Dianeweight: 12 lbsvoltage: 110
5", 10", 20", 30”, 48” or 72"field cuttable downrods available
6" diameter
Sum
mer
201
3The Diane can be mounted with any one of the following downrod lengths: 5, 10, 20, 30, 48 or 72”. The Diane is compatible with flat or vaulted ceilings. Safety cages available for low ceiling applications.
**Damp location: All standard finishes with metal blades. Not recommended for salt water / ocean front applications. **Damp Location1881 Industrial Drive Libertyville, IL 60048 Tele: 847.680.9043 Fax: 847.680.8140 www.matthewsfanco.com
13"16"
12"10"
2"
90 ̊side-to-sideoscillation
MATTHEWS F A N C O M P A N Y
SKU Naming Convention
Finishes Blade TypeWood - WD Metal w/ Decorative Cage - MTL Metal w/ Safety Cage - MSAF
Brushed Nickel - BN Polished Chrome - CR Textured Bronze - TB
DI-XX-XXX (Model-Finish-Blade Type)
CFM: 3087(Wood Blades)
CFM: 2497(Metal Blades)
DampLocation:
All Finisheswith MetalBlades.**
Safety cage equipped
The Melody oscillating, 3-speed wall mounted fan provides maximum multi-directional airflow. It can be mounted in small, awkward spaces or in front of HVAC ducts to make more efficient the heating, ventilation or air conditioning of any room.
· Available in the following finishes: polished chrome, brushed nickel or textured bronze.· Constructed of cast aluminum and heavy stamped steel, the Melody carries a limited lifetime warranty.· Equipped with hand-balanced metal blades and metal safety cages.· 3-speed wall control is standard equipment.· To operate the oscillation mechanism independent of the fan blades, a three wire system is needed.
shown in Polished Chrome with metal blades
shown in Brushed Nickel with metal blades
shown in Textured Bronze with metal blades
MelodyDesigned in 2008
Sum
mer
201
3
20"
20"
13"
90 ̊left to right oscillation
5.5"
2.5"
Melodyweight: 14 lbsvoltage: 110**Please contact us for possible 220 conversion
MATTHEWS F A N C O M P A N Y
**Damp location: All standard finishes with metal blades. Not recommended for salt water / ocean front applications.
**Damp Location
1881 Industrial Drive Libertyville, IL 60048 Tele: 847.680.9043 Fax: 847.680.8140 www.matthewsfanco.com
The motor angle and projection can be customized
the field-cuttableby a simple alteration to
gooseneck.
CFM: 2497(Metal Blades)
SKU Naming Convention
Finishes
Brushed Nickel - BN Polished Chrome - CR Textured Bronze - TB
ME-XX (Model-Finish)
DampLocation:
All Finisheswith MetalBlades.**
Safety cage equipped
The über-cool Cinni oscillating, 3-speed table fan provides stylish multi-directional airflow.
• Available in the following finishes: polished chrome, brushed nickel or textured bronze.• Constructed of cast aluminum and heavy stamped steel, the Cinni carries a limited lifetime warranty.• Equipped with hand-balanced metal blades and metal safety cages.
CinniDesigned in 2011
shown in textured bronze
shown in brushed nickel
shown in polished chrome
14"
9"
18"
13"
90 ̊oscillation left - right
3-speedfan motor control
"On - Off"oscillation control
Sprin
g 20
13
**Damp Location
1881 Industrial Drive Libertyville, IL 60048 Tele: 847.680.9043 Fax: 847.680.8140 www.matthewsfanco.com
**Damp location: All standard finishes with metal blades. Not recommended for salt water / ocean front applications.
Cinniweight: 14 lbsvoltage: 110
MATTHEWS F A N C O M P A N Y
SKU Naming Convention
Finishes
Brushed Nickel - BN Polished Chrome - CR Textured Bronze - TB
CI-XX (Model-Finish)
CFM: 2497(Metal Blades)
Cutting a figure like no other, the Irene-3 is rustic, yet strikingly modern.
Irene-3 is inspired by the golden age of aviation with three neatly joined propeller-shaped, solid walnut-stained wooden blades. A spherical motor housing complements its minimal profile. Irene-3 is streamline while still appearing warm and natural.
• 52” diameter with three solid wood, walnut-stained machine-cut blades.• Energy efficient six speed, reversible DC motor with new, reliable technology.• Damp location finishes: brushed nickel, polished chrome or textured bronze.• Constructed of cast aluminum and heavy stamped steel.• Limited Lifetime Warranty• Standard equipment: • One downrod of 5”, 10”, 20” or 30”. (48” and 72” downrods are also available.) • Vaulted ceiling mount canopy up to 29 degrees. Option for greater slant available. • Remote control, hand-held and wall mountable.
Irene-3
shown in Textured Bronze
shown in Polished Chrome
shown in Brushed Nickel
Designed in 2013
DampLocation:
All Finishes**
Sum
mer
201
3
7"
6" diameter
9"
2"
5", 10", 20", 30", 48" or 72" downrods available
52"
MATTHEWS F A N C O M P A N Y
1881 Industrial Drive Libertyville, IL 60048 Tele: 847.680.9043 Fax: 847.680.8140 www.matthewsfanco.com
The Irene-3 is compatible with flat or vaulted ceilings and can be mounted with any one of the following downrod lengths: 5”, 10”, 20”, 30”, 48” and 72”.
The Irene-3 is compatible with vaulted ceilings mount canopy up to 29 degrees. Option for greater slant available.
**Damp location: All standard finishes Not recommended for salt water / ocean front applications
Irene-3weight: 17 lbsvoltage: 110**Please contact us for possible 220 conversion
SKU Naming Convention
Finishes Brushed Nickel - BN Polished Chrome - CR Textured Bronze - TB
IR3-XX (Model-Finish)
Irene-5shown in Textured Bronze
shown in Polished Chrome
shown in Brushed Nickel
Cutting a figure like no other, the Irene-5 is rustic, yet strikingly modern.
Irene-5 is inspired by the golden age of aviation with five neatly joined propeller-shaped, solid walnut-stained wooden blades. A spherical motor housing complements its minimal profile. Irene-5 is streamline while still appearing warm and natural.
• 52” diameter with five solid wood, walnut-stained machine-cut blades.• Energy efficient six speed, reversible DC motor with new, reliable technology.• Damp location finishes: brushed nickel, polished chrome or textured bronze.• Constructed of cast aluminum and heavy stamped steel.• Limited Lifetime Warranty• Standard equipment: • One downrod of 5”, 10”, 20” or 30”. (48” and 72” downrods are also available.) • Vaulted ceiling mount canopy up to 29 degrees. Option for greater slant available. • Remote control, hand-held and wall mountable.
Designed in 2012
DampLocation:
All Finishes**
6"
6" diameter
9"
2"
5", 10", 20", 30", 48" or 72" downrods available
52"
MATTHEWS F A N C O M P A N Y
Irene-5weight: 18 lbsvoltage: 110**Please contact us for possible 220 conversion
Sum
mer
201
3
1881 Industrial Drive Libertyville, IL 60048 Tele: 847.680.9043 Fax: 847.680.8140 www.matthewsfanco.com
The Irene-5 is compatible with flat or vaulted ceilings and can be mounted with any one of the following downrod lengths: 5”, 10”, 20”, 30”, 48” and 72”.
The Irene-5 is compatible with vaulted ceilings mount canopy up to 29 degrees. Option for greater slant available.
**Damp location: All standard finishes Not recommended for salt water / ocean front applications
SKU Naming Convention
Finishes Brushed Nickel - BN Polished Chrome - CR Textured Bronze - TB
IR5-XX (Model-Finish)
Safety cage equipped
DampLocation:
All Finisheswith MetalBlades.**
shown as wall fan in Polished Chrome
shown as wall fan in Textured Bronze
shown as ceiling fan in Brushed Nickel
The beautiful Kaye oscillating, 3-speed wall or ceiling fan, reminiscent of train cabin ventilators of yester-year, will cool down your favorite space with poise and determination. Kaye’s profile is low, however its strength and character define it. • Kaye can be mounted in small or awkward spaces or in front of HVAC ducts to make more efficient the heating, ventilation or air conditioning of a room. • Available in the following finishes: polished chrome, brushed nickel or textured bronze.• Constructed of cast aluminum and heavy stamped steel, the Kaye carries a limited lifetime warranty.• Equipped with hand-balanced metal blades and metal safety cages.• 3-speed wall control is standard equipment.• To operate the oscillation mechanism independent of the fan blades, a three wire system is needed.
KayeDesigned in 2012
Kayeweight: 10.5 lbsvoltage: 110
Sum
mer
201
3
1881 Industrial Drive Libertyville, IL 60048 Tele: 847.680.9043 Fax: 847.680.8140 www.matthewsfanco.com
**Damp Location
**Damp location: All standard finishes with metal blades. Not recommended for salt water / ocean front applications.
MATTHEWS F A N C O M P A N Y
5.5"diameter
17.5"
4.5"13"
13"
90º Left to RightOscillation
CFM: 2497(Metal Blades)
SKU Naming Convention
Finishes Brushed Nickel - BN Polished Chrome - CR Textured Bronze - TB
KC-XX (Model-Finish)