Boundary Lubrication Layer Mechanisms
O. O. Ajayi, C. Lorenzo-Martin, R. A. Erck, G. R. FenskeArgonne National LaboratoryJune 10, 2010
Project ID # VSS003
This presentation does not contain any proprietary, confidential, or otherwise restricted information
2
Overview
Start date - 2004 End date - 2012 Percent complete – 85%
Barriers addressed– Safety, durability, and reliability– Computational models, design and
simulation methodologies– Higher vehicular operational
demands• Total project funding
– DOE share – 2,500K – Contractor share
• Funding • FY09 – 400K• FY10 - 225K
Timeline
Budget
Barriers
• Interactions/ collaborations• Caterpillar Inc.• Eaton Corporation• Castrol-BP• Oakland University
Partners
3
Largest source Untapped Energy is Efficiency gain
Exxon Mobil-News_pub_2008_energyoutlook
• Efficiency gain is largest source of energy
• In Vehicles, significant fuel savings and consequently imported petroleum oil can be achieved through efficiency gain
Project Conception: Friction reduction in vehicle lubricated
components and systems translates to improved efficiency.
Increased power density results in size reduction and fuel saving.
High friction and high power density failures occur in poorly understood boundary lubrication regime.
Project Description
Axle -2%
Transmission – 3%
Fuel Injectors
Valve-Train Components
Rings/Liners
Turbochargers
Liquid Lubricants
Bearings & Gears
Engine – 4-5%
5
Overall Project Objectives
– Achieve sustainable friction reduction and increase power density in lubricated components and vehicle systems by developing a better understanding of boundary lubrication mechanisms• Determine the mechanisms of
boundary layer formation and loss rates as well as the film properties• Determine the mechanisms of
catastrophic failure by scuffing• Develop integrated low-friction high
power density interface
Technical Approach
Project Plan and Structure
Near-surface-material dynamicchanges: - scuffing
Boundary film formation and loss rate: - APS, other surface analysis tools
Basic mechanism of scuffing failure Prediction and prevention
Mechanical and friction properties of boundary films measurement
Role of surface modification:- coatings
Models for film formation, mechanical and frictional behavior
Integrate both elements with EHD and HD lubrication to formulate failure/performance prediction methodology for lubricated components
Materials Chemical FilmsDetermine basic
mechanisms of poorly understood near surface
material and surface chemical boundary
films. Integrate three structural components
of lubrication
Significant Previous Technical Accomplishments Developed and validated a scuffing model for metallic materials following extensive
microstructural characterization :– Scuffing initiates by adiabatic shear instability – can predict shear strain required– Scuffing propagates by contact interface heat management– Prediction of scuffing from material properties - currently being used as a design guide
by one of the industrial partners
Based on the model, evaluated scuffing resistance of several materials pairs with high scuffing resistance
Demonstrated the use of multiple x-ray based surface analytical techniques for in-situ characterization of tribochemical boundary films
Initiated development of tribochemical boundary films structural characterization
“Take-home” message: - Pathway for high power density material; - pathway to better understanding of tribochemical film structure, properties and performance
8
FY10 Technical Accomplishments: Developed and demonstrated a
unique technique for boundary film structural characterization by combining ion beam milling (FIB) and transmission electron microscopy (TEM)
Pt deposited to protect the boundary film during ion beam milling
Cross-section TEM sample prepared by FIB
9
0
0.05
0.1
0.15
0.2
0 2000 4000 6000 8000 10000
µ - Oil A-40Cµ - Oil B-100Cµ - Oil C-100C
Fric
tion
Coe
ffici
ent
Time (s)
Significant differences in friction behavior for the 3 oils
FY10 Technical Accomplishment
•The viscosity, and hence fluid film thickness in the three lubricants are equivalent.
• Materials for the test are all the same
•Differences in friction behavior can be attributed to differences in the structure and properties of the boundary films
‘Take-home’ message: Friction behavior of different lubricants reflects differences in the structure of their tribochemical films –pathway to durable low-friction boundary films
10
Optical Microscopy and profilometry of tribochemical film
BLOCK- 1018 ROLLER-52100
Sliding direction
Uniformity in direction of sliding
Non-contact
area
11
FY10 Technical Accomplishments:
TEM analysis showed different features of boundary films produced from different lubricants – Film thickness 80 – 120 nm range– Some regions are nano crystalline– Other regions are amorphous
Monolayer film Bi-layer film Tri-layer film
Amorphous region
Nano crystalline region(5-10 nm crystal size)
TEM of subsurface and tribochemical (BF) films
12
TEM macro image of near-surface material, tribochemical film and Pt layer
Steel-crystalline BF interface Steel-amorphous BF interface Amorphous-crystalline BF Amorphous BF
13
Glazing Incidence X ray Diffraction (GIXRD)
.•Conducted at Advance Photon Source (APS)
• Beam 2ID-D
•Operating Conditions: E=10.1 Kev., λ= 1.23 Å
PRELIMINARY HIGHLIGHTS
•Broad peaks of tribo-film. Broadness indicative of nano-size of grains
•Indication of some amorphous layer by the reduction of intensity in some films
•So far, results from X-ray analysis are consistent with TEM observations.
Sample
d~10 nm
5 105
5.5 105
6 105
6.5 105
7 105
7.5 105
8 105
8.5 105
26 26.5 27 27.5 28 28.5 29 29.5 30
Inte
nsity
2 thetaExperimental set up
14
FY10 Technical Accomplishment - Boundary film structure and friction behavior connection
• Differences in friction behavior can be attributed to differences in the structure and properties of the boundary films• Lower friction lubricants (A and B) contain more
armphous structure• Higher friction lubricant with steady behavior
contains mostly nano-crystalline film as determined by X-ray and TEM
–
15
FY10 Technical Accomplishment: Nano Mechanical properties of tribochemical films
Nano mechanical properties of the tribo chemical films determined by instrumented nano-indenter system
Tribo film surfaces were first imaged by scanning (AFM) prior to indentation.
Hardness and elastic modulus of the films are determined.
Mechanical behavior of the film can also be inferred from the load-displacement curve during loading and unloading.
‘Take-home’ message: Mechanical properties and behavior of tribo-chemical films are dependent on the structure of the films.
Nano-mechanical properties of Low-friction films
Hardness - 3.8 GPa Elastic modulus – 90 GPa Complex mechanical behavior
Steel substrate – 7.8 GPa and modulus – 200 GPa
Nano-mechanical properties of higher-friction films
Hardness - 6.4 GPa Elastic modulus – 152 GPa Elasto-plastic mechanical behavior
Steel substrate – 7.8 GPa and modulus – 200 GPa
Collaborations
Caterpillar Inc. (Industry): Collaboration on the validation study of scuffing model.
Castrol-BP Inc. (Industry): Collaboration of the formulation of lubricants to form a variety of different tribo-chemical boundary films.
Eaton Corp. (Industry): Collaboration on the measurement of boundary film structure and boundary lubrication friction for transmission gear oil and materials.
Oakland University (Academic): Collaboration to model contact temperatures and stresses during boundary lubrication sliding contacts.
18
19
Proposed Future Work. Continue structural characterization of boundary films with differing tribological
properties– FIB and TEM– Glancing incidence X-ray techniques at APS– Surface profilometry and AFM
Continue measurement of nano mechanical and frictional properties of structurally different boundary films using a nano mechanical probe system– Provide pathway for structure-properties relationship formulation for boundary
layer films– Indication of mechanical failure mechanisms of boundary films
In view of the impact of contact temperature on boundary film formation and frictional behavior, we plan to develop and refine the technique for the measurement of lubricated contact real temperature using the thermoelectric principle. Measurements will be conducted under various contact conditions.– Measurement essential to modeling boundary film formation kinetics– Input for boundary lubrication friction prediction– Assess the correlation of measured and calculated contact temperatures
20
Summary Increase in vehicle systems power density facilitated by this project through better
understanding and prediction of scuffing will result in significant petroleum displacement
– Size and weight reduction in many systems– Efficient and cost effective product development
Results of the structure-properties-frictional performance connection for tribochemical boundary films being developed in this project will facilitate achievement of reliable and sustainable friction reduction in numerous pertinent vehicle components and systems
– Effective and efficient lubricant formulation for various materials.– Prediction of friction for real surfaces and lubricants.
Results of the project have general applicability for all vehicle systems.
Potential for 5 -15 % fuel savings via efficiency gain is increasingly achievable