1E-BFR
Cost Saving
Greater Safe Working Load
H65-66%
H105-50%
Space Saving
w w w . b a s o r . c o m
NOW
BEFORE
2 E-BFR
Safety edges to prevent cable damage.
Full Range of fast fixing accessories.
Innovative design patented by BASOR which offers:
• Greater flexure resistance.
• Greater Safe Working Load.
• Excelent aesthetic finish.
Quicker and easier assembly:
• The trays can be moulded with a simple manipulation to obtain complicated changes in directions.
• The cuts have to be performed with aymmetrical-cut wire cutters.
• The cut has to be performed as near as possible to the intersection of the wires, in order to obtain a clean cut and a good assembly.
2
1
3
4
CABLE CAPACITY (cm2)
B(mm) H65 H105
60 21 -
100 43 -
150 72 -
200 100 186
300 156 291
400 212 396
500 268 501
600 324 606
1
* See the technical annex of the catalogue B03 or ask us for technical advice.
2
3
3
2 7UNE-EN 61537
150ºC
-50ºC
UNE-EN 61537
M0
UNE-EN 61537UNE 23727
UNE-EN 61537
*L > 100 m
1
2
Stackable Wire-Mesh Cable TraysBASORFILSCM
E-BFR
3E-BFR
H65B H EZ HDG
DESCRIPTION mm mm REF. kg/m REF. kg/mBASORFIL E-BFR 100X65 100 65 2/7305 0,77 2/7326 0,83
BASORFIL E-BFR 150X65 150 65 2/7306 0,82 2/7327 0,89
BASORFIL E-BFR 200X65 200 65 2/7307 1,06 2/7328 1,15
BASORFIL E-BFR 300X65 300 65 2/7308 1,57 2/7329 1,69
BASORFIL E-BFR 400X65 400 65 2/7309 1,90 2/7330 2,05
BASORFIL E-BFR 500X65 500 65 2/7310 2,46 2/7331 2,65
BASORFIL E-BFR 600X65 600 65 2/7311 2,83 2/7332 3,05
To assembly E-BFR H65 cable trays use a quick joint BFR 35 E-BFR 65/105 (2/7271 in EZ, 2/7272 in HDG) on each side of the cable trays. For trays wider than 300 an aditional bolt-staple set shall be used as central union joint (2/4364 in EZ, 2/4360 in HDG).
H-7
B + 15
50
100L = 3 m
H105B H EZ HDG
DESCRIPTION mm mm REF. kg/m REF. kg/mBASORFIL E-BFR 200X105 200 105 2/7312 1,57 2/7333 1,69
BASORFIL E-BFR 300X105 300 105 2/7313 1,90 2/7334 2,05
BASORFIL E-BFR 400X105 400 105 2/7314 2,46 2/7335 2,65
BASORFIL E-BFR 500X105 500 105 2/7315 2,83 2/7336 3,05
BASORFIL E-BFR 600X105 600 105 2/7316 3,20 2/7337 3,45
To assembly E-BFR H105 cable trays use a quick joint BFR 65/105 E-BFR 105 (2/6217 in EZ, 2/6219 in HDG) on each side of the cable trays. A quick joint BFR H35 E-BFR 65/105 can be added as an extra reinforcement (optional).
B + 18
H -
4 25
50
100
L = 3 m
QUICK JOINTSEZ HDG
DESCRIPTION REF. kg/ud REF. kg/udQUICK JOINT BFR 65/105 E-BFR 105 2/6217 0,03 2/6219 0,03
QUICK JOINT BFR 35 E-BFR 65/105 2/7271 0,04 2/7272 0,04
Fast fix couple for BASORFIL trays, BF, BFR and E-BFR. Screwless.
Simple and fast to assemble. For a perfect fit, tighten the tabs withs pliers.
34
464412
Stackable Wire-Mesh Cable TraysBASORFILSCM
E-BFR
BOLT-STAPLE SETEZ HDG
DESCRIPTION REF. kg/ud REF. kg/udBF BOLT-STAPLE SET 2/4364 0,03 2/4360 0,03
It consists of a BF-bolt set and a BF-staple.
Bolted coupler for all BASORFIL tray series.
20
6
28
18
4 E-BFR
STBPG HDG
DESCRIPTION REF. kg/ud REF. kg/udSTB 2/0356 0,14 2/0366 0,14
Take-off plate for rigid pipes 16, 20 and 25.
You can see the Insulating Conduit Cable Conduction Systems (SCP) in our products catalogue B02.
SSC CENTRAL SUSPENSIONEZ HDG
DESCRIPTION REF. kg/ud REF. kg/udSSC CENTRAL SUSPENSION 2/2064 0,03 2/0363 0,03
The SSC allows to fix the tray to the ceiling with a M8 threated rod (2/3397 - EZ).
Each attachment point requires two SSC (upper an lower), one rod and two M8 DIN 6923 nuts (0/0338 in EZ, 0/0338 in HDG).
Also can be used as a fastener between wire mesh trays and any horizontal support with a B1 bolt set (2/4356 in EZ, 2/6826 in HDG).
BF STAPLEEZ HDG
DESCRIPTION REF. kg/ud REF. kg/udBF STAPLE 2/0337 0,01 2/0339 0,01
It is used to mount the divider profile.
BF BOLT-NUT SETPap EZ HDG
DESCRIPTION Nm REF. kg/ud REF. kg/udBF BOLT-NUT SET 4 2/4362 0,02 2/7132 0,02
Patented BF-Bolt and a nut DIN 6923. The BF-Bolt is specifically designed by BASOR to form a perfect fit between the wire trays.
20
6
23
21
28
18
8x8
6
50
40
60
9
2123,5
29
81 14
127
Stackable Wire-Mesh Cable TraysBASORFILSCM
E-BFR
MULTI UNION JOINTPG HDG
DESCRIPTION REF. kg/ud REF. kg/udMULTIUNION JOINT 2/0357 0,05 - 0,05
Supplement used in the workplace for construction of accessories (vertical inside/outside, horizontal bend, reduction, etc.)
1650
025
18x7.5
5E-BFR
UNIVERSAL SUPPORT BOXPG HDG
DESCRIPTION REF. kg/ud REF. kg/udUNIVERSAL SUPPORT BOX 2/0358 0,28 2/0368 0,28
For fixing the watertight boxess of the leading manufacturers: Legrand, Gewiss, Eunea, etc.
For fixing:Square shape 29-70 (mm).Rectangular shape 79x50, 98-128x50, 15-55x82 (mm).Straight line from 30 to 147 (mm).
104
200
5
715029
112144
5
2880 72 50 25
35x7,5
12x8
25
8,5
DROP-OUT PLATEPG HDG
DESCRIPTION REF. kg/ud REF. kg/udDROP OUT PLATE BF/BFR 2/6451 0,18 2/6452 0,20
To assemble drop-out plate with cable trays use a SSC, a M8x25 DIN 933 bolt (0/0310 in EZ) and a DIN 6923 nut (0/0338 in EZ).
148
9
176
R100
DIVIDER PROFILE PSH PG HDG
DESCRIPTION mm REF. kg/m REF. kg/mPS 35 35 2/3476 0,23 2/3479 0,29
PS 60 60 2/2066 0,34 2/3480 0,43
PS 80 80 2/3477 0,46 2/3481 0,63
PS 100 100 2/3478 0,56 2/3482 0,76
One B1 bolt set (2/4356 in EZ, 2/6826 in HDG) and one BASORFIL staple (2/0337 in EZ, 2/0339 in HDG) are required to fix the divider profile to the wire-mesh cable tray every 500 mm.
The divider profile allows better organization of cables.
It is strongly recommended its use in systems with electromagnetic compatibility issues to separate data and power cables.
2550
20x8
20
H-5
L = 3 m
HORIZONTAL BEND VERTICAL INSIDE LEVEL CHANGE
Multijunction joint can be used to reinforce
the accessories.
Multijunction joint can be used to reinforce
the accessories.
Multijunction joint can be used to reinforce
the accessories.
VERTICAL OUTSIDE+INSIDE
Stackable Wire-Mesh Cable TraysBASORFILSCM
E-BFR
6 E-BFR
C-SHOB e SWL PG HDG
DESCRIPTION mm mm (kg) REF. kg/ud REF. kg/udFAST FIXING SUPPORT C-SHO 100 1,5 98 2/7230 0,38 2/7239 0,41
FAST FIXING SUPPORT C-SHO 150 2 90 2/7231 0,43 2/7240 0,47
FAST FIXING SUPPORT C-SHO 200 2 69 2/7232 0,49 2/7241 0,53
FAST FIXING SUPPORT C-SHO 300 2 45 2/7233 0,55 2/7242 0,59
SHO/SHOT SUPPORTING PIECE - 2 - 2/6240 - 2/6318 -
No aditional pieces are required to fix wire-mesh cable trays. The design of the brackets, with the T-shaped fixing flap, allows a resistant and easy installation of the trays BASORFIL BFR/BF only using a flat baded screwdriver.
For anchoring to the wall, a SHO supporting piece (2/6240 in EZ, 2/6318 in HDG) is necessary. If SHO supporting piece is not used the SWL values fell by 12% and the profile can crash when the anchor presses it.
C-SHOTB e CTA PG HDG
DESCRIPTION mm mm (kg) REF. kg/ud REF. kg/udFAST FIXING SUPPORT C-SHOT 100 100 1,5 98 2/7235 0,43 2/7244 0,48
FAST FIXING SUPPORT C-SHOT 150 150 2 90 2/7236 0,62 2/7245 0,67
FAST FIXING SUPPORT C-SHOT 200 200 2 69 2/7237 0,67 2/7246 0,73
FAST FIXING SUPPORT C-SHOT 300 300 2 45 2/7238 0,79 2/7247 0,85
SHO/SHOT SUPPORTING PIECE - 2 - 2/6240 - 2/6318 -
No aditional pieces are required to fix wire-mesh cable trays. The design of the brackets, with the T-shaped fixing flap, allows a resistant and easy installation of the trays BASORFIL BFR/BF only using a flat baded screwdriver.
For anchoring to the wall, a SHO supporting piece (2/6240 in EZ, 2/6318 in HDG) is necessary. If SHO supporting piece is not used the SWL values fell by 12% and the profile can crash when the anchor presses it.
SVOB e CTA PG/EZ HDG
DESCRIPTION mm mm (kg) REF. kg/ud REF. kg/udSVO 100 SUPPORT 100 1,5 250 2/3630 0,24 2/6280 0,26
SVO 150 SUPPORT 150 1,5 200 2/1073 0,24 2/1078 0,26
SVO 200 SUPPORT 200 2 294 2/1074 0,37 2/1079 0,39
SVO 300 SUPPORT 300 2 235 2/1076 0,49 2/1081 0,52
SVO 400 SUPPORT 400 2 161 2/3629 0,55 2/5719 0,59
SVO 500 SUPPORT 500 2 115 2/1077 0,67 2/1082 0,72
SVO 600 SUPPORT 600 2 87 2/5941 0,78 2/5720 0,84
M8 THREADED ROD - - - 2/3397 0,35 - -
M8 DIN 6923 NUT - - - 0/0338 0,01 0/0348 0,01
No aditional pieces are required to fix wire-mesh cable trays. The design of the brackets, with the T-shaped fixing flap, allows a resistant and easy installation of the trays BASORFIL BFR/BF only using a flat baded screwdriver.
To mount the SVO support to ceiling, 2 M8 threaded rods, 4 M8 DIN 6923 nuts and 2 anchorages plugs for threaded rod BASORFIX CM8x30 are needed.
B + 92B + 112
113
2550
52
e 5020x9
175
20
113
B + 112
2550
52
255020x9
20x9
52
20
e
B +
100
2550
20x9
Supports for Wire-Mesh Cable TraysBASORSUPPORTSCM
7E-BFR
C-PC+C-SR + SPLIT PIN DIN94 DETAIL PC CLICK PORF.+HEAD+C-SR C-PC+HEAD+C-SR+REINFORCEMENT
PC CLICK HEADe PG
DESCRIPTION mm REF. kg/udPC CLICK HEAD 2 2/7270 0,24
SR/PC M8 BOLT SET - 2/6793 0,24
8x80 DIN 94 SPLIT PIN - 2/7297 0,37
The PC click head allows the construction of ceiling supports with PC profile (with single or double profile) using bolts or split pins.
To fix the PC profile to the PC click head two bolts or split pins are required.
Also, with 2 additional heads and one additional profile, 45 degrees reinforcements can be mounted to increase the resistance of the ceiling support.
To attach the PC click head to the rear face of the PC and built the reinforcements, 2 B2 bolt sets (2/4926 in EZ) are needed.
C-SR SUPPORTe B H A SWL PG
DESCRIPTION mm mm mm mm kg REF. kg/udC-SR 200 SUPPORT 1,5 200 65 30 102 2/7264 0,36
C-SR 300 SUPPORT 1,5 300 65 30 90 2/7265 0,49
C-SR 400 SUPPORT 1,5 400 100 60 159 2/7266 0,81
C-SR 500 SUPPORT 1,5 500 100 60 134 2/7267 0,97
C-SR 600 SUPPORT 1,5 600 100 60 117 2/7268 1,14
SR/PC M8 BOLT SET - - - - - 2/6793 0,24
8x80 DIN 94 SPLIT PIN - - - - - 2/7297 0,37
The C-SR support is designed for assemblies with PC or PC click profile using 2 SR/PC M8 bolt sets or 2 8x80 DIN 94 split pins (only one bolt set/pin on models 200 and 300).
No additional pieces are required to fix the wire-mesh cable trays. The design of the brackets, with the T-shaped fixing flap, allows a resistant and easy installation of the trays BASORFIL BFR/BF only using a flat baded screwdriver.
PC CLICK PROFILEe B H PG
DESCRIPTION mm mm mm REF. kg/udPC CLICK PROFILE 2 58 35 2/7269 1,75
The PC click profile, and its wide range of accessories (PC click head, articulated bracket, pins, etc.) allow a large variety of celing, wall and tunnel assemblies.
Supported on the open face of the profile for mounting horizontal supports C-SR
Supported on the wings of the profile for mounting horizontal supports SCR and SRB.
130
8,56063
90
25x11
95
e
B + 50
H A 8,5
50
53
50 20x9
9
B
H
e
30
20x9 8,5
3000
30
Supports for Wire-Mesh Cable TraysBASORSUPPORTSCM
e - m a i l : b a s o r @ b a s o r. c o m