MAGNA-SKIN TM Magnetic ProductsMagnetic ProductsMagnetic ProductsMagnetic Products
Inside…..
• Magna-SkinTM - Magnetic wear liners
• Magna-PatchTM - Pipe and equipment patches
• Magna-PlateTM - Wear plate retaining system
• Magna-WedgeTM - Tramp metal protection
• Suspended Plate Magnets
• ACR Product Line Card
Molded from high wearing rubber or urethane,
Magna-skin™ wear pads and liners from the
ACR Group install without welding, bolting or
adhesives, fastening with magnetic force alone.
They install quickly and easily to chutes, bins, hoppers or any ferrous metal impact areas to keep production running at your mine site.
Features and BenefitsFeatures and BenefitsFeatures and BenefitsFeatures and Benefits • Fastens with magnetic force – no welding, bolting or adhesives required • Easily and quickly repositionable • Fifty percent less change-out time compared to bolt-on liners • Standard 12” x 12” size, in thicknesses of 1” (sidewalls and other areas with less abrasion or impact) and 2” (heavy wear areas) • Can be cut with a tile saw to fit odd dimensions and a wide range of surface areas
Solid rubber construction effectively seals off the equipment surface and
prevents material buildup. Repositioning and replacement of the Magna-skin™ magnetic liners is fast and simple when some have worn more than
others, stretching the life of the overall lining and reducing downtime. Change out the
worn liners or swap for others in the same chute that are
seeing less wear.
Revolutionary new wear product!
• Custom sizes and corner section liners available • Additional options/styles: - Internal use liners For small areas enduring Severe ongoing wear - With ceramic wear surface - Specialty applications ApplicationsApplicationsApplicationsApplications • Chutes • Bins • Hoppers • Ferrous metal impact areas
Magna-SkinTM Magnetic Wear Liners
Minimize Downtime and Maximize Efficiency.
www.acrgroup.ca
Check out our web site for results of independent impact and holding force
testing of these liners. In all tests the liners held in place without movement.
Patent Pending
Magnetic Wear Liners
• Installation of the magnetic liners involves simply cleaning the ferrous metal surface where the liners will be installed and then fitting into place with each pad against the next
• Start at the bottom of chutes or angled
hoppers, fitting the first row of pads against the bottom plate or angle iron and then adding more liners up from there
• All exposed edges must be supported by either equipment wall or angle iron keeper bars to prevent vibration movement.
• Magna-SkinTM magnetic liners can be cut with a tile saw to allow for fitting in odd dimensional areas
• To change out pads, insert a pry bar or other thin metal tool under the liner and lift to break the magnetic bond with the steel equipment
• Liners can also be custom made to custom sizes on request
• Holds in place even under heavy impact conditions
• Tremendous holding strength
increases with each liner installed
• Extreme wear polymer for
impact and abrasion resistance
• Easy to install in hard to reach
processing areas • Protect chute surfaces, bins,
troughs, hoppers, side walls, tank bottoms and more
Magna-SkinTM Magnetic Wear Liners
Install easily and quickly with no welding,
bolting or adhesives
Patent Pending
Magna-SkinTM Black For larger ore size or where material is dropping from an overhead conveyor or
chute. Molded in our proprietary rubber in hardness 60 duro shore A.
For large or fine ore size where material is tumbling or sliding across wear surface with or without impact. Molded in our
proprietary rubber in hardness 40 duro shore A.
For sharp materials causing impact and/or sliding abrasion where rubber is not
suitable or where better release properties are needed.
Molded in our proprietary compound with a ceramic surface for fine
sharp particles, heat resistance or applications with no impact.
Magna-Skin TM Magnetic wear liners come in different materials to suit your specific wear
application. Whether you are moving large rock or fine sand, from smooth to sharp particles, there is a Magna-Skin
TM liner that will do the job.
Our standard 12” X 12” liners come in 1” or 2” thicknesses molded with rubber, urethane, ceramic or Uhmw surfaces. Magna-Skin
TM liners save huge time in installation
and change out, keeping your production running longer and more efficiently.
Magna-SkinTM Magnetic Wear Liner Selection
Hard 90 urethane for impact and/or slidingabrasion where rubber is not
suitable or where better release properties are needed.
www.acrgroup.ca
Molded in our proprietary compound with a UHMW surface for fine
sharp particles. Low coefficient of friction and good wear characteristics along with excellent
release properties.
Magna-SkinTM Blue
Magna-SkinTM Red
Magna-SkinTM Green
Magna-SkinTM White
Magna-SkinTM UHMW
A few examples of where Magna-SkinTM Magnetic liners
have proven to work well.
Mining applicationsMining applicationsMining applicationsMining applications Bins Bucket Liners Chutes Conveyor transfer points Crusher infeed areas Ore Deflectors Discharge Chutes Feed Chutes Floatation Tanks Hoppers Impact Liners Impact Walls Launders Loaders Mill discharge chutes Rock Box edges Mill infeed areas Screen Equipment sidewalls Side Bar & Wall protection Sluices Tanks Transfer Chutes Tripper / Fine Ore separation Troughs
Coal mines and power plants Coal mines and power plants Coal mines and power plants Coal mines and power plants Coal Loading Hoppers & Feeders Conveyor transition points Crusher Plant wear areas Deflectors Feeders Preparation/Wash Plant wear areas Screen chutes and sidewalls Wash Plants Flop Gate Doors Deflector plate protection
Aggregate applicationsAggregate applicationsAggregate applicationsAggregate applications Primary infeed Chutes Pre-Wash areas Separation side walls and discharge areas Screen discharge areas Deflector plate protection Screen sidewall protection Dumper hoppers and Drop Boxes
MangaMangaMangaManga----SkinSkinSkinSkinTM TM TM TM magnetic wear liners also work great to protect equipment from damage in magnetic wear liners also work great to protect equipment from damage in magnetic wear liners also work great to protect equipment from damage in magnetic wear liners also work great to protect equipment from damage in abrasive processing areas of corn, soya, grains, sugar, salt and other food products.abrasive processing areas of corn, soya, grains, sugar, salt and other food products.abrasive processing areas of corn, soya, grains, sugar, salt and other food products.abrasive processing areas of corn, soya, grains, sugar, salt and other food products.
www.acrgroup.ca
Magna-SkinTM products save your production time and money!
Magna-PatchTM
• A fast, temporary patching solution for leaks and holes in steel pipes and other processing equipment until a permanent repair can be made
• Reusable - Comes with replaceable wear pads for repeated use
• Tension screw pushes the disposable wear pad tight against
the leak - all in seconds
• Quick solution for spill containment
• Patented Technology
•
• Available styles:
◊ MP-611 (mini)
For use on smaller diameter
piping and radii surfaces, or hard
to reach areas
◊ MP-711
For use on larger steel surfaces such as bins and hoppers, chute bottoms and troughs or similar
◊ MP-811
For use on larger diameter piping and radii surfaces, or
tough holes in corner or odd shaped steel parts or equipment
Magna-PatchTM
products can be used to quickly repair leaks in steel hulled boats and ships.
Magna-PatchTM
Products provide a quick seal until the leak source can be cut off and permanently repaired, reducing
clean up costs.
www.acrgroup.ca
Magna-PlateTM
• Patented powerful, shock absorbing magnetic wear plate fastening and retaining system
• Suited for abrasive and heavy impact material conveying
• Delivers impact absorption and noise reduction
• Offers Quick, clean and safe change outs
• Eliminates fire hazards and time consuming cut out, welding, grinding and gouging associated with typical wear plate replacement
Magna-PlateTM
• Quick removal and secure installation of wear plate
• No welding or bolting to change out
• Ability to use with any ferrous metal wear plate
• Simple tools required for wear plate change out
• Keeps wear plate in place while the polymer absorbs the impact, allowing production to continue
MAGNA-PLATE™ powerful magnetic fastener,
absorbs shock and vibration “impact zone”
high abrasion
and impact area
Abrasive material
Wear plate
Magna-WedgeTM
Suspended Plate Magnets
• Separates, captures and retains unwanted ferrous tramp metal before it enters processing equipment
• Installs easily and permanently in conveying equipment and feeders
• Applications include vibratory feeders, gravity feed systems and similar conveying or process equipment
• Protect chippers, hogs, grinders, feeders and other size reduction equipment
• Reduce metal detector tripping
Magna-WedgeTM products can be used in any processing application where there is need to
remove tramp metal from product in a vibratory or gravity feed system.
Ask us about vibration components for
conveyor and feeder other equipment.
• Simple Installation- install above product
flow or at discharge, no electrical hook ups
• Constant power - Permanent magnet
requires no electricity
• No Maintenance
• No moving parts
• Easy cleaning
Non-Ferrous
Material Flow
Mounted over the Belt
Material Discharge
Non-Ferrous
Material Flow
Mounted at Discharge End
Material Discharge
Patented Technology
www.acrgroup.ca
MOLDED RUBBER
Bearing Pads
Bushings
Compression Boots
Diaphragms
DissipatorTM Products
Idlers
Impact Bars
Layboy Tires
Lifter Bars
Mill Liners
Molded Gaskets
Pump Liners
Rotors & Stators
Sorter Sling Straps
Suction Box Seals
Suction Cups
Tension Bands
Vibration Isolators
Vibration Mounts
Wear Linings
ROLL COVERING
Clipper Rolls (Veneer)
Direct Coater Rolls
Drive & Feed Rolls
Felt Rolls
Glue Spreader Rolls
Hourglass Rolls
Idler Rolls
Isolator Rolls
Packaging & Treating
FABRICATED RUBBER
Chip Feeder Dust boots
Chute Fabrication & Lining
Expansion Joints & Sleeves
Chute Lining
De-mineralizing Tanks
Dust & Vent Sleeves
Expansion Joints
Launder Lining
Launder Linings
Mill Liners
Pipes, Spools & Fittings
Pulley Lagging & Grooving
Pump Casings & Impellors
Railcar Linings
Rubber Bladders
Rubber to Metal Bonding
Tank & Vessel Lining
EXTRUDED SHAPES
Belly Bands
Dock & Marine Bumpers
Dock Bumpers
Extruded Tubing
Fuel Tank Straps
Kiln Door Seal
Mill Seals
Snow Plow Blades
Snubber Rubbers
Supac Valves
T-Scale & P-Seal
SHEET RUBBER
Cloth Inserted, Epdm,
Hypalon, Natural, Neoprene,
Nitrile, SBR, Silicone,
Sponge, Tan gum,
HOSE PRODUCTS
(Vacuum & Suction)
Abrasion Resistant
Chemical Service
Discharge Hoses
Material Handling Hoses
Sleeves & Connectors
Specialty End Types
Wire & Kevlar Reinforced
Discharge Hoses
Hump Hoses
Suction Box hose
URETHANE PRODUCTS
DissipatorTM Products
Impact Cushions & Pads
Pulleys
Rotors & Stators
Wear Liners
Clamp Feet
Impact Cushions & Pads
Wheels & Rollers
Score Rings
Custom Compounds
Vibration products
A sample of our products
Contact ACR today !
Magna-SkinTM Products
Distributed by:
ACR Group Inc. Richmond BC Phone 604-274-9955 Fax 604-274-1013
ACR Group Inc. Nisku AB Phone 780-955-2802 Fax 780-955-8909
Printed in Canada