1
This product can be set up usingThis product can be set up usingThis product can be set up usingThis product can be set up usingThis product can be set up usingananananany curry curry curry curry currenenenenent web brt web brt web brt web brt web browserowserowserowserowser, i.e, i.e, i.e, i.e, i.e.,.,.,.,.,Internet Explorer 6 or NetscapeInternet Explorer 6 or NetscapeInternet Explorer 6 or NetscapeInternet Explorer 6 or NetscapeInternet Explorer 6 or NetscapeNavigator 6.2.3.Navigator 6.2.3.Navigator 6.2.3.Navigator 6.2.3.Navigator 6.2.3.
DWL-2100APD-LinkD-LinkD-LinkD-LinkD-Link AirAirAirAirAirPlusPlusPlusPlusPlus XtremeGXtremeGXtremeGXtremeGXtremeGTMTMTMTMTM
802.11g/108Mbps802.11g/108Mbps802.11g/108Mbps802.11g/108Mbps802.11g/108MbpsWirWirWirWirWireless Aeless Aeless Aeless Aeless Access Pccess Pccess Pccess Pccess Poinoinoinoinointtttt
5V 2.0A DC Power Adapter
©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software andspecifications subject to change without notice. DWL-2100AP. 11122003
Before You Begin
Check Your Package Contents
DWL-2100AP 802.11g/108Mbps WirelessAccess Point
CD-ROM (containing Manual and Warranty)
Ethernet (CAT5 UTP) Cable
If any of the above items are missing, please contact your reseller.
It’s best to use a computer (with an Ethernet adapter) that is connected to a switch forconfiguring the DWL-2100AP. The default IP address for the DWL-2100AP is192.168.0.50 with a Subnet Mask of 255.255.255.0. You will need to assign yourcomputer a Static IP address within the same range as the DWL-2100AP’s IP addressfor the purpose of configuring the DWL-2100AP. See the Appendix if you needassistance in assigning a Static IP address for your network adapter.
Using a power supply with a different voltagerating will damage and voidthe warranty of this product.
�
������������ ���������
�������������������������������� ���������� ���������������������������������������������
�������� �������������������������������������������������������������������������������������������������������������������������������������������������������� ��� �!����������"���������������������������������������
������#� �����������������������������������������������������������������������������������������������������������������������������������������$ � ���������#�%�&'����� �����$ � ���������((�)*' ����+�,����� ����-��������������������������������������������.����������/������������������� ����������������� ��!��������"�������������/������������������������"����������������� �$���+�!���"������������������������������� ������0�#10�#2 �0�����.�������� ���� ������������������� �-���"��������������������������������"������������������������������ '
�������!�������3%)������� �2���/��3������ �4����� ���������������������3)�������� �2���/��3������ ��4#�����������������������������������5������������������������ �������������������� � ���� �4�/����� �����6�� �������� �������� ������� ���������������������������
�������������� ���������������������������������������
������������7 ���������� �.�����������6�� ���1��������
�������������� ���� ���������� ����
�������� ���������� ������������.��������� ����
3
Using the Setup Wizard
Open your Webbrowser and type“http://192.168.0.50”into the URL addressbox. Then press theEnter or Return key.
The logon pop-upscreen will appear.
Type “admin” for theusername and leave thepassword field blank.
Click OK
When you have com-pleted the steps in thisQuick Installation Guide,your connected networkshould look similar tothis:
4
Once you havelogged in, the Homescreen will appear.
You will see thefollowing screens.
Click Run Wizard
Click Next
Using The Setup Wizard (continued)
5
Click Next
Step 1 - Set up your newpassword. You have theoption to establish a password.
Step 2 - Wireless SetupThe default wirelesssettings are:SSID = defaultChannel = 6You can change thesesettings to match anexisting wireless network.
Click Next
Using The Setup Wizard (continued)
6
Step 3 - EncryptionThe DWL-2100AP is capable oftwo levels of wireless encryption64-bit and 128-bit. By defaultthe encryption is disabled.You can change the encryptionsettings for more securewireless communication.
Your Setup is Complete!
Using The Setup Wizard (continued)
Click Next
Click Restart
7
Click Close
You will be returned to the Home tab.
Click to Exit
For additional settings or information, refer to the Advanced, Tools, or Statustabs on the web-management interface; or to the manual located on the CD-ROM.
8
AppendixTo assign a Static IP Address to the laptop or computer that you are using to configurethe DWL-2100AP, please do the following:
Assigning a Static IP Address in Windows
Go to Start > Double- click on ControlPanel > Double-click on NetworkConnections > Right-click on LocalArea Connections > Click Properties
Highlight Internet Protocol (TCP/IP)
Click Properties
Select Use the following IP address inthe Internet Protocol (TCP/IP) Propertieswindow
Click OK
Input your IP address and subnet mask.(The IP Address must be within the samerange as the DWL-2100AP. The IP Addressof the DWL-2100AP is 192.168.0.50. Youcan assign 192.168.0.51 for your computer.No two computers can have the same IPAddress. Assign a subnet mask of255.255.255.0.)
9
For Windows 2000 users:For Windows 2000 users:For Windows 2000 users:For Windows 2000 users:For Windows 2000 users:Go to Start > Settings > Network andDial-up Connections > Double-click on theLocal Area Connection associated withthe Network Adapter installed on yoursystem> select Properties
Click Properties
Click Internet Protocol (TCP/IP)
Select Use the following IP address
Input your IP address and subnet mask.(The IP Address must be within the samerange as the DWL-2100AP. The IP Addressof the DWL-2100AP is 192.168.0.50. Youcan assign 192.168.0.52 for your computer.No two computers can have the same IPAddress. Assign a subnet mask of255.255.255.0.)
Click OK
10
Click Internet Protocol (TCP/IP)Go to Start > Settings > Control Panel >Double-click on the Local Area Connectionassociated with the Network Adapter installedon your system > select Properties
For Windows Me and 98se users:For Windows Me and 98se users:For Windows Me and 98se users:For Windows Me and 98se users:For Windows Me and 98se users:
Click Properties
Click Internet Protocol (TCP/IP)
Select Specify IP Address
Input your IP address and subnet mask.(The IP Address must be within the samerange as the DWL-2100AP. The IP Addressof the DWL-2100AP is 192.168.0.50. Youcan assign 192.168.0.52 for your computer.No two computers can have the same IPAddress. Assign a subnet mask of255.255.255.0.)
Click OK
11
For Apple Macintosh OS X:
Go to the Apple Menu Click on Networkand Select System Preferences
Select Built inEthernet in the Showpull-down menu
Click onApply Now
Select Manually in theConfiguration pull-downmenu
Input your IP address andsubnet mask. (The IP Addressmust be within the same range asthe DWL-2100AP. The IP Addressof the DWL-2100AP is192.168.0.50. You can assign192.168.0.51 for your Macintosh.No two computers can have thesame IP Address. Assign asubnet mask of 255.255.255.0.)
12
TTTTTechniechniechniechniechnical Supportcal Supportcal Supportcal Supportcal SupportYou can find software updates and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States andwithin Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through ourwebsite, or by phone.
Tech Support for customers within the United States:D-Link Technical Support over the Telephone:(877) 453-546524 hours a day, seven days a week.
D-Link Technical Support over the Internet:http://support.dlink.comemail:[email protected]
Tech Support for customers within Canada:D-Link Technical Support over the Telephone:(800) 361-5265Monday to Friday 8:30am to 9:00pm EST
D-Link Technical Support over the Internet:http://support.dlink.caemail:[email protected]