A Regional Ice-Ocean SimulationOf the Barents and Kara Seas
W. Paul Budgell
Institute of Marine Researchand
Bjerknes Centre for Climate ResearchBergen, Norway
ROMS User Meeting, VeniceOctober 18-21, 2004
IMR
IMR
Outline of Talk:
• Background
• Description of ice-ocean model
• Model set-up
• Simulation results • Comparison with observations
IMR
BackgroundRegion of interest is the Barents SeaDynamical downscaling experimentsFirst replicate present-day climate
Validate with available observations
IMR
Model Domain
IMR
Ocean Model Component
• Community Regional Ocean Modelling System (ROMS) version 2.1
• Terrain-following coordinate system with generalized vertical coordinate, curvilinear coordinates in horizontal
• Wide variety of mixing schemes available
• Advanced numerics, OMP and MPI parallel.
IMR
Ocean Model Component
• Used 3rd-order upwind-biased horizontal advection
• Used piece-wise parabolic splines in vertical, spline vertical advection, spline Jacobian baroclinic pressure gradient at topography
• Used GLS mixing with MY2.5 parameters
• No explicit horizontal viscosity or diffusivity
IMR
Ice Dynamics
Ice dynamics are based upon the elastic-viscous-plastic (EVP)rheology of Hunke and Dukowicz (1997), Hunke (1991) and Hunke and Dukowicz (1992).
Under low deformation (rigid behaviour), the singularity is regularized by elastic waves. The response is very similar toviscous-plastic models in typical Arctic pack ice conditions.
Numerical behaviour improved significantly by applyinglinearization of the viscosities at every EVP time step.
The EVP model parallelizes very efficiently under both OpenMPAnd MPI.
IMR
Ice Thermodynamics
Ice thermodynamics are based upon those of Mellor andKantha (1989) and Häkkinen and Mellor (1992). Main featuresinclude:• Three-level, single layer ice; single snow layer• Molecular sublayer under ice; Prandtl-type ice-ocean boundary layer• Surface melt ponds• Forcing by short and long-wave radiation, sensible and latent heat flux• NCEP fluxes, corrected for model surface temperature and ice concentration, used as forcing
IMR
Model Set-up
IMR
Model Set-up
• Horizontal resolution of 7.8 to 10.5 km, average of 9.3 km
• 32 levels in the vertical
• Flather (free surface) and Chapman (momentum) open boundary conditions for 2D variables
• Nudging + radiation condition OBCs for 3D-mom and tracers
IMR
Boundary and Initial Conditions
• Tidal forcing from AOTIM
• Coarse model used for initialization and boundary forcing of regional model
• 50 km resolution in Nordic Seas/Arctic
• NCEP daily mean fluxes (Bentsen and Drange, 2001) used for forcing
• Hindcast from 1948-2002 completed, archived 5-day mean fields
IMR
IMR
IMR
Results are shown from the first yearof a1990-2002 simulation
SST Ice Concentration
IMR
Comparison with observations:
SST from PODAAC Pathfinder AVHRRbest SST, ascending (day-time) orbit,8-day, 9-km means
Ice concentration from SSM/I passive micowave, daily means
Bjørnøya-Fugløya CTD sections
IMR
SST
IMR
Sea Ice Concentration
IMR
Section Locations
IMR
T - Bjørnøya-Fugløya Section - March
IMR
T - Bjørnøya-Fugløya Section – Sept.
IMR
S - Bjørnøya-Fugløya Section – Sept.
IMR
Brine Drainage Spitzbergen Section
IMR
Brine Drainage W. Novoya Zemlya Section
IMR
Ice Production - 1993
IMR
Ice Melt - 1993
IMR
Conclusions
• Model captures seasonal variability in the Barents • Good agreement with observed ice distribution
• Barents inflow is too cold, too fresh – OBC issue
• Brine rejection from ice formation produces realistic water masses
• ROMS captures significant portion of mesoscale variability even with 9-km resolution