Relion 670 series
Line distance protection REL670Technical reference manual
Document ID: 1MRK 506 312-UENIssued: December 2012
Revision: CProduct version: 1.2
Copyright 2012 ABB. All rights reserved
CopyrightThis document and parts thereof must not be reproduced or copied without writtenpermission from ABB, and the contents thereof must not be imparted to a thirdparty, nor used for any unauthorized purpose.The software and hardware described in this document is furnished under a licenseand may be used or disclosed only in accordance with the terms of such license.TrademarksABB and Relion are registered trademarks of the ABB Group. All other brand orproduct names mentioned in this document may be trademarks or registeredtrademarks of their respective holders.WarrantyPlease inquire about the terms of warranty from your nearest ABB representative.
ABB ABSubstation Automation ProductsSE-721 59 VstersSwedenTelephone: +46 (0) 21 32 50 00Facsimile: +46 (0) 21 14 69 18http://www.abb.com/substationautomation
DisclaimerThe data, examples and diagrams in this manual are included solely for the conceptor product description and are not to be deemed as a statement of guaranteedproperties. All persons responsible for applying the equipment addressed in thismanual must satisfy themselves that each intended application is suitable andacceptable, including that any applicable safety or other operational requirementsare complied with. In particular, any risks in applications where a system failure and/or product failure would create a risk for harm to property or persons (including butnot limited to personal injuries or death) shall be the sole responsibility of theperson or entity applying the equipment, and those so responsible are herebyrequested to ensure that all measures are taken to exclude or mitigate such risks.This document has been carefully checked by ABB but deviations cannot becompletely ruled out. In case any errors are detected, the reader is kindly requestedto notify the manufacturer. Other than under explicit contractual commitments, inno event shall ABB be responsible or liable for any loss or damage resulting fromthe use of this manual or the application of the equipment.
ConformityThis product complies with the directive of the Council of the EuropeanCommunities on the approximation of the laws of the Member States relating toelectromagnetic compatibility (EMC Directive 2004/108/EC) and concerningelectrical equipment for use within specified voltage limits (Low-voltage directive2006/95/EC). This conformity is the result of tests conducted by ABB inaccordance with the product standards EN 50263 and EN 60255-26 for the EMCdirective, and with the product standards EN 60255-1 and EN 60255-27 for the lowvoltage directive. The product is designed in accordance with the internationalstandards of the IEC 60255 series.
Table of contents
Section 1 Introduction.....................................................................31Introduction to the technical reference manual.................................31
About the complete set of manuals for an IED............................31About the technical reference manual.........................................32This manual.................................................................................33
Introduction.............................................................................33Principle of operation..............................................................33Input and output signals.........................................................36Function block........................................................................36Setting parameters.................................................................36Technical data........................................................................37
Intended audience.......................................................................37Related documents......................................................................37Revision notes.............................................................................38
Section 2 Analog inputs..................................................................39Introduction.......................................................................................39Operation principle...........................................................................39Function block..................................................................................40Setting parameters...........................................................................41
Section 3 Local HMI.......................................................................47Human machine interface ................................................................47Small size HMI..................................................................................49
Small............................................................................................49Design.........................................................................................49
Medium size graphic HMI.................................................................51Medium........................................................................................51Design.........................................................................................51
Keypad.............................................................................................53LED...................................................................................................54
Introduction..................................................................................54Status indication LEDs................................................................54Indication LEDs...........................................................................54
Local HMI related functions..............................................................55Introduction..................................................................................55General setting parameters.........................................................56Status LEDs.................................................................................56
Design....................................................................................56Function block........................................................................56
Table of contents
1Technical reference manual
Input and output signals.........................................................56Indication LEDs...........................................................................57
Introduction.............................................................................57Design....................................................................................57Function block........................................................................64Input and output signals.........................................................64Setting parameters.................................................................64
Section 4 Basic IED functions........................................................67Authorization.....................................................................................67
Principle of operation...................................................................67Authorization handling in the IED...........................................68
Self supervision with internal event list.............................................69Introduction..................................................................................69Principle of operation...................................................................69
Internal signals.......................................................................71Run-time model......................................................................73
Function block.............................................................................74Output signals..............................................................................74Setting parameters......................................................................74Technical data.............................................................................75
Time synchronization........................................................................75Introduction..................................................................................75Principle of operation...................................................................75
General concepts...................................................................75Real-time clock (RTC) operation............................................78Synchronization alternatives..................................................79Process bus IEC 61850-9-2LE synchronization.....................82
Function block.............................................................................82Output signals..............................................................................82Setting parameters......................................................................83Technical data.............................................................................86
Parameter setting groups.................................................................86Introduction..................................................................................86Principle of operation...................................................................86Function block.............................................................................87Input and output signals..............................................................88Setting parameters......................................................................88
ChangeLock function CHNGLCK.....................................................88Introduction..................................................................................89Principle of operation...................................................................89Function block.............................................................................89Input and output signals..............................................................89Setting parameters......................................................................90
Table of contents
2Technical reference manual
Test mode functionality TEST..........................................................90Introduction..................................................................................90Principle of operation...................................................................90Function block.............................................................................92Input and output signals..............................................................92Setting parameters......................................................................93
IED identifiers...................................................................................93Introduction..................................................................................93Setting parameters......................................................................93
Product information..........................................................................94Introduction..................................................................................94Setting parameters......................................................................94Factory defined settings..............................................................94
Signal matrix for binary inputs SMBI................................................95Introduction..................................................................................95Principle of operation...................................................................95Function block.............................................................................95Input and output signals..............................................................96
Signal matrix for binary outputs SMBO ...........................................96Introduction..................................................................................96Principle of operation...................................................................97Function block.............................................................................97Input and output signals..............................................................97
Signal matrix for mA inputs SMMI....................................................98Introduction..................................................................................98Principle of operation...................................................................98Function block.............................................................................98Input and output signals..............................................................98
Signal matrix for analog inputs SMAI...............................................99Introduction..................................................................................99Principle of operation...................................................................99Frequency values........................................................................99Function block...........................................................................101Input and output signals............................................................101Setting parameters....................................................................102
Summation block 3 phase 3PHSUM..............................................104Introduction................................................................................104Principle of operation.................................................................104Function block...........................................................................105Input and output signals............................................................105Setting parameters....................................................................105
Authority status ATHSTAT.............................................................106Introduction................................................................................106
Table of contents
3Technical reference manual
Principle of operation.................................................................106Function block...........................................................................106Output signals............................................................................106Setting parameters....................................................................107
Denial of service DOS....................................................................107Introduction................................................................................107Principle of operation.................................................................107Function blocks..........................................................................107Signals.......................................................................................108Settings......................................................................................108
Section 5 Differential protection...................................................1091Ph High impedance differential protection HZPDIF .....................109
Identification..............................................................................109Introduction................................................................................109Principle of operation.................................................................109
Logic diagram.......................................................................110Function block...........................................................................110Input and output signals............................................................110Setting parameters....................................................................111Technical data...........................................................................111
Section 6 Impedance protection ..................................................113Distance measuring zones, quadrilateral characteristicZMQPDIS, ZMQAPDIS, ZDRDIR...................................................113
Identification..............................................................................113Introduction................................................................................113Principle of operation.................................................................114
Full scheme measurement...................................................114Impedance characteristic.....................................................115Minimum operating current...................................................119Measuring principles............................................................119Directional impedance element for quadrilateralcharacteristics......................................................................122Simplified logic diagrams......................................................124
Function block...........................................................................127Input and output signals............................................................128Setting parameters....................................................................129Technical data...........................................................................132
Distance measuring zone, quadrilateral characteristic forseries compensated lines ZMCPDIS, ZMCAPDIS, ZDSRDIR.......132
Introduction................................................................................133Principle of operation.................................................................134
Full scheme measurement...................................................134
Table of contents
4Technical reference manual
Impedance characteristic.....................................................135Minimum operating current...................................................138Measuring principles............................................................138Directionality for series compensation..................................141Simplified logic diagrams......................................................143
Function block...........................................................................146Input and output signals............................................................147Setting parameters....................................................................149Technical data...........................................................................152
Phase selection, quadrilateral characteristic with fixed angleFDPSPDIS......................................................................................152
Identification..............................................................................152Introduction................................................................................153Principle of operation.................................................................153
Phase-to-earth fault..............................................................155Phase-to-phase fault............................................................157Three-phase faults...............................................................159Load encroachment..............................................................159Minimum operate currents....................................................164Simplified logic diagrams......................................................164
Function block...........................................................................169Input and output signals............................................................170Setting parameters....................................................................171Technical data...........................................................................172
Full-scheme distance measuring, Mho characteristicZMHPDIS ......................................................................................172
Introduction................................................................................172Principle of operation.................................................................173
Full scheme measurement...................................................173Impedance characteristic.....................................................174Basic operation characteristics.............................................175Theory of operation..............................................................177Simplified logic diagrams......................................................185
Function block...........................................................................188Input and output signals............................................................189Setting parameters....................................................................190Technical data...........................................................................191
Full-scheme distance protection, quadrilateral for earth faultsZMMPDIS, ZMMAPDIS..................................................................192
Introduction................................................................................192Principle of operation.................................................................193
Full scheme measurement...................................................193Impedance characteristic.....................................................193Minimum operating current...................................................195
Table of contents
5Technical reference manual
Measuring principles............................................................196Directional lines....................................................................198Simplified logic diagrams......................................................200
Function block...........................................................................203Input and output signals............................................................203Setting parameters....................................................................204Technical data...........................................................................206
Directional impedance element for mho characteristic andadditional distance protection directional function for earthfaults ZDMRDIR, ZDARDIR...........................................................206
Introduction................................................................................207Principle of operation.................................................................207
Directional impedance element for mho characteristicZDMRDIR.............................................................................207Additional distance protection directional function forearth faults ZDARDIR...........................................................210
Function block...........................................................................212Input and output signals............................................................212Setting parameters....................................................................213
Mho impedance supervision logic ZSMGAPC................................214Introduction................................................................................214Principle of operation.................................................................215
Fault inception detection......................................................215Function block...........................................................................216Input and output signals............................................................216Setting parameters....................................................................217
Faulty phase identification with load encroachmentFMPSPDIS.....................................................................................217
Introduction................................................................................218Principle of operation.................................................................218
The phase selection function................................................218Function block...........................................................................229Input and output signals............................................................230Setting parameters....................................................................230Technical data...........................................................................231
Distance protection zone, quadrilateral characteristic, separatesettings ZMRPDIS, ZMRAPDIS and ZDRDIR................................231
Introduction................................................................................232Principle of operation.................................................................233
Full scheme measurement...................................................233Impedance characteristic.....................................................233Minimum operating current...................................................237Measuring principles............................................................237
Table of contents
6Technical reference manual
Directional impedance element for quadrilateralcharacteristics......................................................................240Simplified logic diagrams......................................................242
Function block...........................................................................245Input and output signals............................................................246Setting parameters....................................................................247Technical data...........................................................................249
Phase selection, quadrilateral characteristic with settableangle FRPSPDIS............................................................................250
Introduction................................................................................250Principle of operation.................................................................251
Phase-to-earth fault..............................................................253Phase-to-phase fault............................................................255Three-phase faults...............................................................256Load encroachment..............................................................257Minimum operate currents....................................................262Simplified logic diagrams......................................................263
Function block...........................................................................267Input and output signals............................................................268Setting parameters....................................................................269Technical data...........................................................................270
Power swing detection ZMRPSB ...................................................270Introduction................................................................................270Principle of operation.................................................................270
Resistive reach in forward direction.....................................272Resistive reach in reverse direction.....................................272Reactive reach in forward and reverse direction..................273Basic detection logic.............................................................273Operating and inhibit conditions...........................................276
Function block...........................................................................277Input and output signals............................................................277Setting parameters....................................................................278Technical data...........................................................................279
Power swing logic ZMRPSL ..........................................................279Introduction................................................................................279Principle of operation.................................................................279
Communication and tripping logic........................................279Blocking logic.......................................................................280
Function block...........................................................................282Input and output signals............................................................282Setting parameters....................................................................283
Pole slip protection PSPPPAM ......................................................283Introduction................................................................................283Principle of operation.................................................................283
Table of contents
7Technical reference manual
Function block...........................................................................287Input and output signals............................................................287Setting parameters....................................................................288Technical data...........................................................................288
Automatic switch onto fault logic, voltage and current basedZCVPSOF ......................................................................................289
Introduction................................................................................289Principle of operation.................................................................289Function block...........................................................................291Input and output signals............................................................291Setting parameters....................................................................291Technical data...........................................................................292
Phase preference logic PPLPHIZ...................................................292Introduction................................................................................292Principle of operation.................................................................292Function block...........................................................................295Input and output signals............................................................295Setting parameters....................................................................296
Section 7 Current protection.........................................................299Instantaneous phase overcurrent protection 3-phase outputPHPIOC .........................................................................................299
Introduction................................................................................299Principle of operation.................................................................299Function block...........................................................................300Input and output signals............................................................300Setting parameters....................................................................300Technical data...........................................................................301
Four step phase overcurrent protection OC4PTOC ......................301Introduction................................................................................301Principle of operation.................................................................302Function block...........................................................................307Input and output signals............................................................307Setting parameters....................................................................309Technical data...........................................................................314
Instantaneous residual overcurrent protection EFPIOC ................315Introduction................................................................................315Principle of operation.................................................................315Function block...........................................................................316Input and output signals............................................................316Setting parameters....................................................................316Technical data...........................................................................317
Four step residual overcurrent protection, zero, negativesequence direction EF4PTOC .......................................................317
Table of contents
8Technical reference manual
Introduction................................................................................317Principle of operation.................................................................318
Operating quantity within the function..................................318Internal polarizing.................................................................319External polarizing for earth-fault function............................321Base quantities within the protection....................................321Internal earth-fault protection structure................................322Four residual overcurrent steps............................................322Directional supervision element with integrateddirectional comparison function............................................323Second harmonic blocking element.....................................325Switch on to fault feature......................................................327
Function block...........................................................................329Input and output signals............................................................330Setting parameters....................................................................331Technical data...........................................................................336
Four step directional negative phase sequence overcurrentprotection NS4PTOC .....................................................................336
Introduction................................................................................337Principle of operation.................................................................337
Operating quantity within the function..................................337Internal polarizing facility of the function..............................338External polarizing for negative sequence function..............339Base quantities within the function.......................................339Internal negative sequence protection structure..................340Four negative sequence overcurrent stages........................340Directional supervision element with integrateddirectional comparison function............................................341
Function block...........................................................................344Input and output signals............................................................344Setting parameters....................................................................345Technical data...........................................................................350
Sensitive directional residual overcurrent and power protectionSDEPSDE .....................................................................................350
Introduction................................................................................350Principle of operation.................................................................352
Function inputs.....................................................................352Function block...........................................................................358Input and output signals............................................................359Setting parameters....................................................................360Technical data...........................................................................362
Thermal overload protection, one time constant LPTTR................363Introduction................................................................................363Principle of operation.................................................................363
Table of contents
9Technical reference manual
Function block...........................................................................366Input and output signals............................................................367Setting parameters....................................................................367Technical data...........................................................................368
Breaker failure protection CCRBRF ..............................................368Introduction................................................................................368Principle of operation.................................................................369Function block...........................................................................372Input and output signals............................................................372Setting parameters....................................................................373Technical data...........................................................................373
Stub protection STBPTOC ............................................................374Introduction................................................................................374Principle of operation.................................................................374Function block...........................................................................375Input and output signals............................................................375Setting parameters....................................................................376Technical data...........................................................................376
Pole discordance protection CCRPLD ..........................................376Introduction................................................................................377Principle of operation.................................................................377
Pole discordance signaling from circuit breaker...................380Unsymmetrical current detection..........................................380
Function block...........................................................................380Input and output signals............................................................381Setting parameters....................................................................381Technical data...........................................................................382
Directional underpower protection GUPPDUP...............................382Introduction................................................................................382Principle of operation.................................................................383
Low pass filtering..................................................................385Calibration of analog inputs..................................................385
Function block...........................................................................386Input and output signals............................................................387Setting parameters....................................................................387Technical data...........................................................................388
Directional overpower protection GOPPDOP ................................389Introduction................................................................................389Principle of operation.................................................................390
Low pass filtering..................................................................392Calibration of analog inputs..................................................392
Function block...........................................................................393Input and output signals............................................................394
Table of contents
10Technical reference manual
Setting parameters....................................................................394Technical data...........................................................................396
Broken conductor check BRCPTOC .............................................396Introduction................................................................................396Principle of operation.................................................................396Function block...........................................................................398Input and output signals............................................................398Setting parameters....................................................................398Technical data...........................................................................399
Section 8 Voltage protection........................................................401Two step undervoltage protection UV2PTUV ................................401
Introduction................................................................................401Principle of operation.................................................................401
Measurement principle.........................................................402Time delay............................................................................402Blocking................................................................................408Design..................................................................................409
Function block...........................................................................411Input and output signals............................................................411Setting parameters....................................................................412Technical data...........................................................................414
Two step overvoltage protection OV2PTOV ..................................415Introduction................................................................................415Principle of operation.................................................................415
Measurement principle.........................................................416Time delay............................................................................416Blocking................................................................................422Design..................................................................................422
Function block...........................................................................424Input and output signals............................................................424Setting parameters....................................................................425Technical data...........................................................................427
Two step residual overvoltage protection ROV2PTOV .................427Introduction................................................................................428Principle of operation.................................................................428
Measurement principle.........................................................428Time delay............................................................................428Blocking................................................................................434Design..................................................................................434
Function block...........................................................................435Input and output signals............................................................436Setting parameters....................................................................436Technical data...........................................................................438
Table of contents
11Technical reference manual
Overexcitation protection OEXPVPH ............................................438Introduction................................................................................439Principle of operation.................................................................439
Measured voltage.................................................................441Operate time of the overexcitation protection.......................442Cooling.................................................................................446Overexcitation protection function measurands...................446Overexcitation alarm............................................................447Logic diagram.......................................................................447
Function block...........................................................................448Input and output signals............................................................448Setting parameters....................................................................448Technical data...........................................................................450
Voltage differential protection VDCPTOV ......................................450Introduction................................................................................450Principle of operation.................................................................450Function block...........................................................................452Input and output signals............................................................452Setting parameters....................................................................452Technical data...........................................................................453
Loss of voltage check LOVPTUV ..................................................453Introduction................................................................................453Principle of operation.................................................................454Function block...........................................................................455Input and output signals............................................................456Setting parameters....................................................................456Technical data...........................................................................456
Section 9 Frequency protection....................................................457Underfrequency protection SAPTUF .............................................457
Introduction................................................................................457Principle of operation.................................................................457
Measurement principle.........................................................458Time delay............................................................................458Voltage dependent time delay..............................................458Blocking................................................................................460Design..................................................................................460
Function block...........................................................................461Input and output signals............................................................461Setting parameters....................................................................461Technical data...........................................................................462
Overfrequency protection SAPTOF ...............................................462Introduction................................................................................463Principle of operation.................................................................463
Table of contents
12Technical reference manual
Measurement principle.........................................................463Time delay............................................................................463Blocking................................................................................464Design..................................................................................464
Function block...........................................................................465Input and output signals............................................................465Setting parameters....................................................................465Technical data...........................................................................466
Rate-of-change frequency protection SAPFRC .............................466Introduction................................................................................466Principle of operation.................................................................466
Measurement principle.........................................................467Time delay............................................................................467Blocking................................................................................467Design..................................................................................468
Function block...........................................................................469Input and output signals............................................................469Setting parameters....................................................................469Technical data...........................................................................470
Section 10 Multipurpose protection................................................471General current and voltage protection CVGAPC..........................471
Introduction................................................................................471Principle of operation.................................................................471
Measured quantities within CVGAPC...................................471Base quantities for CVGAPC function..................................474Built-in overcurrent protection steps.....................................474Built-in undercurrent protection steps...................................479Built-in overvoltage protection steps....................................480Built-in undervoltage protection steps..................................480Logic diagram.......................................................................480
Function block...........................................................................485Input and output signals............................................................486Setting parameters....................................................................487Technical data...........................................................................495
Section 11 Secondary system supervision.....................................497Current circuit supervision CCSRDIF ............................................497
Introduction................................................................................497Principle of operation.................................................................497Function block...........................................................................499Input and output signals............................................................499Setting parameters....................................................................500Technical data...........................................................................500
Table of contents
13Technical reference manual
Fuse failure supervision SDDRFUF...............................................500Introduction................................................................................500Principle of operation.................................................................501
Zero and negative sequence detection................................501Delta current and delta voltage detection.............................505Dead line detection...............................................................507Main logic.............................................................................507
Function block...........................................................................511Input and output signals............................................................511Setting parameters....................................................................511Technical data...........................................................................512
Section 12 Control..........................................................................515Synchrocheck, energizing check, and synchronizingSESRSYN......................................................................................515
Introduction................................................................................515Principle of operation.................................................................516
Basic functionality.................................................................516Logic diagrams.....................................................................516
Function block...........................................................................525Input and output signals............................................................525Setting parameters....................................................................528Technical data...........................................................................531
Autorecloser SMBRREC ...............................................................532Introduction................................................................................532Principle of operation.................................................................532
Logic Diagrams....................................................................532Auto-reclosing operation Off and On....................................532Auto-reclosing mode selection.............................................533Start auto-reclosing and conditions for start of areclosing cycle......................................................................533Control of the auto-reclosing open time for shot 1...............534Long trip signal.....................................................................535Time sequence diagrams.....................................................541
Function block...........................................................................544Input and output signals............................................................544Setting parameters....................................................................546Technical data...........................................................................548
Apparatus control APC...................................................................548Introduction................................................................................548Principle of operation.................................................................548Error handling............................................................................549Bay control QCBAY...................................................................551
Introduction...........................................................................551
Table of contents
14Technical reference manual
Principle of operation............................................................551Function block......................................................................553Input and output signals.......................................................553Setting parameters...............................................................554
Local/Remote switch.................................................................554Introduction...........................................................................554Principle of operation............................................................554Function block......................................................................556Input and output signals.......................................................556Setting parameters...............................................................557
Switch controller SCSWI...........................................................557Introduction...........................................................................558Principle of operation............................................................558Function block......................................................................563Input and output signals.......................................................563Setting parameters...............................................................564
Circuit breaker SXCBR..............................................................564Introduction...........................................................................565Principle of operation............................................................565Function block......................................................................569Input and output signals.......................................................569Setting parameters...............................................................570
Circuit switch SXSWI.................................................................570Introduction...........................................................................570Principle of operation............................................................570Function block......................................................................574Input and output signals.......................................................574Setting parameters...............................................................575
Bay reserve QCRSV..................................................................575Introduction...........................................................................576Principle of operation............................................................576Function block......................................................................578Input and output signals.......................................................579Setting parameters...............................................................580
Reservation input RESIN...........................................................580Introduction...........................................................................580Principle of operation............................................................580Function block......................................................................582Input and output signals.......................................................583Setting parameters...............................................................584
Interlocking ....................................................................................584Introduction................................................................................584Principle of operation.................................................................584
Table of contents
15Technical reference manual
Logical node for interlocking SCILO .........................................587Introduction...........................................................................587Logic diagram.......................................................................587Function block......................................................................588Input and output signals.......................................................588
Interlocking for busbar earthing switch BB_ES .........................588Introduction...........................................................................589Function block......................................................................589Logic diagram.......................................................................589Input and output signals.......................................................589
Interlocking for bus-section breaker A1A2_BS..........................590Introduction...........................................................................590Function block......................................................................591Logic diagram.......................................................................592Input and output signals.......................................................593
Interlocking for bus-section disconnector A1A2_DC ................594Introduction...........................................................................595Function block......................................................................595Logic diagram.......................................................................596Input and output signals.......................................................596
Interlocking for bus-coupler bay ABC_BC ................................597Introduction...........................................................................597Function block......................................................................598Logic diagram.......................................................................599Input and output signals.......................................................601
Interlocking for 1 1/2 CB BH .....................................................604Introduction...........................................................................604Function blocks....................................................................605Logic diagrams.....................................................................607Input and output signals.......................................................612
Interlocking for double CB bay DB ...........................................616Introduction...........................................................................616Function block......................................................................617Logic diagrams.....................................................................619Input and output signals ......................................................622
Interlocking for line bay ABC_LINE ..........................................625Introduction...........................................................................625Function block......................................................................626Logic diagram.......................................................................627Input and output signals.......................................................632
Interlocking for transformer bay AB_TRAFO ............................634Introduction...........................................................................635Function block......................................................................636
Table of contents
16Technical reference manual
Logic diagram.......................................................................637Input and output signals.......................................................638
Position evaluation POS_EVAL.................................................640Introduction...........................................................................640Logic diagram.......................................................................640Function block......................................................................641Input and output signals.......................................................641
Logic rotating switch for function selection and LHMIpresentation SLGGIO.....................................................................641
Introduction................................................................................641Principle of operation.................................................................641
Functionality and behaviour ................................................643Graphical display..................................................................643
Function block...........................................................................645Input and output signals............................................................645Setting parameters....................................................................646
Selector mini switch VSGGIO.........................................................647Introduction................................................................................647Principle of operation.................................................................647Function block...........................................................................648Input and output signals............................................................648Setting parameters....................................................................649
IEC61850 generic communication I/O functions DPGGIO.............649Introduction................................................................................649Principle of operation.................................................................649Function block...........................................................................650Input and output signals............................................................650Settings......................................................................................650
Single point generic control 8 signals SPC8GGIO.........................650Introduction................................................................................650Principle of operation.................................................................651Function block...........................................................................651Input and output signals............................................................651Setting parameters....................................................................652
AutomationBits, command function for DNP3.0 AUTOBITS..........652Introduction................................................................................653Principle of operation.................................................................653Function block...........................................................................654Input and output signals............................................................654Setting parameters....................................................................655
Single command, 16 signals SINGLECMD....................................669Introduction................................................................................669Principle of operation.................................................................669
Table of contents
17Technical reference manual
Function block...........................................................................670Input and output signals............................................................670Setting parameters....................................................................671
Section 13 Scheme communication...............................................673Scheme communication logic for distance or overcurrentprotection ZCPSCH........................................................................673
Introduction................................................................................673Principle of operation.................................................................674
Blocking scheme..................................................................674Permissive underreaching scheme......................................674Permissive overreaching scheme........................................675Unblocking scheme..............................................................675Intertrip scheme....................................................................676Simplified logic diagram.......................................................676
Function block...........................................................................678Input and output signals............................................................678Setting parameters....................................................................679Technical data...........................................................................679
Phase segregated scheme communication logic for distanceprotection ZC1PPSCH ...................................................................680
Introduction................................................................................680Principle of operation.................................................................680
Blocking scheme..................................................................681Permissive underreach scheme...........................................681Permissive overreach scheme.............................................682Unblocking scheme..............................................................682Intertrip scheme....................................................................682Simplified logic diagram.......................................................683
Function block...........................................................................684Input and output signals............................................................684Setting parameters....................................................................686Technical data...........................................................................686
Current reversal and WEI logic for distance protection 3-phaseZCRWPSCH ..................................................................................686
Introduction................................................................................686Principle of operation.................................................................687
Current reversal logic...........................................................687Weak-end infeed logic..........................................................687
Function block...........................................................................689Input and output signals............................................................689Setting parameters....................................................................690Technical data...........................................................................690
Local acceleration logic ZCLCPLAL...............................................690
Table of contents
18Technical reference manual
Introduction................................................................................691Principle of operation.................................................................691
Zone extension.....................................................................691Loss-of-Load acceleration....................................................692
Function block...........................................................................692Input and output signals............................................................693Setting parameters....................................................................693
Scheme communication logic for residual overcurrentprotection ECPSCH .......................................................................694
Introduction................................................................................694Principle of operation.................................................................694
Blocking scheme..................................................................695Permissive under/overreaching scheme..............................695Unblocking scheme..............................................................697
Function block...........................................................................698Input and output signals............................................................699Setting parameters....................................................................699Technical data...........................................................................700
Current reversal and weak-end infeed logic for residualovercurrent protection ECRWPSCH...............................................700
Introduction................................................................................700Principle of operation.................................................................701
Directional comparison logic function...................................701Fault current reversal logic...................................................701Weak-end infeed logic..........................................................702
Function block...........................................................................703Input and output signals............................................................703Setting parameters....................................................................704Technical data...........................................................................704
Current reversal and weak-end infeed logic for phasesegregated communication ZC1WPSCH ......................................705
Introduction................................................................................705Principle of operation.................................................................705
Current reversal logic ..........................................................705Function block...........................................................................707Input and output signals............................................................708Setting parameters....................................................................709Technical data...........................................................................709
Direct transfer trip logic...................................................................709Introduction................................................................................710Low active power and power factor protection LAPPGAPC......711
Introduction...........................................................................711Principle of operation............................................................712Function block......................................................................714
Table of contents
19Technical reference manual
Input and output signals.......................................................714Setting parameters...............................................................715Technical data......................................................................715
Compensated over and undervoltage protectionCOUVGAPC..............................................................................716
Introduction...........................................................................716Principle of operation............................................................716Function block......................................................................718Input and output signals.......................................................718Setting parameters...............................................................719Technical data......................................................................720
Sudden change in current variation SCCVPTOC......................720Introduction...........................................................................721Principle of operation............................................................721Function block......................................................................722Input and output signals.......................................................722Setting parameters...............................................................722Technical data......................................................................723
Carrier receive logic LCCRPTRC..............................................723Introduction...........................................................................723Principle of operation............................................................723Function block......................................................................724Input and output signals.......................................................724Setting parameters...............................................................725Technical data......................................................................725
Negative sequence overvoltage protection LCNSPTOV...........725Introduction...........................................................................725Principle of operation............................................................725Function block......................................................................726Input and output signals.......................................................726Setting parameters...............................................................726Technical data......................................................................727
Zero sequence overvoltage protection LCZSPTOV..................727Introduction...........................................................................727Principle of operation............................................................727Function block......................................................................728Input and output signals.......................................................728Setting parameters...............................................................728Technical data......................................................................729
Negative sequence overcurrent protection LCNSPTOC...........729Introduction...........................................................................729Principle of operation............................................................729Function block......................................................................730
Table of contents
20Technical reference manual
Input and output signals.......................................................730Setting parameters...............................................................730Technical data......................................................................731
Zero sequence overcurrent protection LCZSPTOC..................731Introduction...........................................................................731Principle of operation............................................................731Function block......................................................................732Input and output signals.......................................................732Setting parameters...............................................................732Technical data......................................................................733
Three phase overcurrent LCP3PTOC.......................................733Introduction...........................................................................733Principle of operation............................................................733Function block......................................................................734Input and output signals.......................................................734Setting parameters...............................................................735Technical data......................................................................735
Three phase undercurrent LCP3PTUC.....................................735Introduction...........................................................................735Principle of operation............................................................736Function block......................................................................736Input and output signals.......................................................736Setting parameters...............................................................737Technical data......................................................................737
Section 14 Logic.............................................................................739Tripping logic SMPPTRC ...............................................................739
Introduction................................................................................739Principle of operation.................................................................739
Logic diagram.......................................................................741Function block...........................................................................744Input and output signals............................................................744Setting parameters....................................................................745Technical data...........................................................................746
Trip matrix logic TMAGGIO............................................................746Introduction................................................................................746Principle of operation.................................................................746Function block...........................................................................748Input and output signals............................................................748Setting parameters....................................................................749
Configurable logic blocks................................................................750Introduction................................................................................750Inverter function block INV........................................................750OR function block OR................................................................751
Table of contents
21Technical reference manual
AND function block AND...........................................................752Timer function block TIMER......................................................752Pulse timer function block PULSETIMER..................................753Exclusive OR function block XOR.............................................753Loop delay function block LOOPDELAY...................................754Set-reset with memory function block SRMEMORY.................754Reset-set with memory function block RSMEMORY.................755Controllable gate function block GATE......................................756Settable timer function block TIMERSET..................................757Technical data...........................................................................758
Fixed signal function block FXDSIGN............................................758Principle of operation.................................................................758Function block...........................................................................759Input and output signals............................................................759Setting parameters....................................................................759
Boolean 16 to Integer conversion B16I..........................................760Introduction................................................................................760Principle of operation.................................................................760Function block...........................................................................760Input and output signals............................................................760Setting parameters....................................................................761
Boolean 16 to Integer conversion with logic noderepresentation B16IFCVI................................................................761
Introduction................................................................................761Principle of operation.................................................................762Function block...........................................................................762Input and output signals............................................................762Setting parameters....................................................................763
Integer to Boolean 16 conversion IB16..........................................763Introduction................................................................................763Principle of operation.................................................................763Function block...........................................................................764Input and output signals............................................................764Setting parameters....................................................................765
Integer to Boolean 16 conversion with logic noderepresentation IB16FCVB...............................................................765
Introduction................................................................................765Principle of operation.................................................................765Function block...........................................................................766Input and output signals............................................................766Setting parameters....................................................................767
Section 15 Monitoring.....................................................................769Measurements................................................................................769
Table of contents
22Technical reference manual
Introduction................................................................................770Principle of operation.................................................................771
Measurement supervision....................................................771Measurements CVMMXN.....................................................775Phase current measurement CMMXU.................................780Phase-phase and phase-neutral voltage measurementsVMMXU, VNMMXU..............................................................781Voltage and current sequence measurements VMSQI,CMSQI..................................................................................781
Function block...........................................................................781Input and output signals............................................................783Setting parameters....................................................................786Technical data...........................................................................799
Event counter CNTGGIO................................................................800Identification..............................................................................800Introduction................................................................................801Principle of operation.................................................................801
Reporting..............................................................................801Design..................................................................................801
Function block...........................................................................802Input signals..............................................................................802Setting parameters....................................................................803Technical data...........................................................................803
Event function EVENT....................................................................803Introduction................................................................................803Principle of operation.................................................................803Function block...........................................................................805Input and output signals............................................................805Setting parameters................................................................