Step 1
Seat Removal: The seat bottom must be removed to install
the covers. Locate one of two clips under the seat bottom
towards the outside of the vehicle. Pull each clip forward to
release the front of the cushion. Push back on the seat while
rotating the front up to release the entire seat bottom.
Step 2
Seat Removal: The hand in the picture is pointing to one of
the two clips that hold the back of the seat down. You will
need to reconnect to these after the cover is installed.
Step 3
Seatbelt Removal: Release the center seatbelt at the
bottom. Push in on the white button and pull the seatbelt
out.
Step 4
Seatbelt Removal: Pull the shoulder belt out of the carrier
on top of the seat.
1741 Back Seat Installation Instructions
Step 5
Passenger Backrest: Pry the top cover off from behind to
expose the screws.
Step 6
Passenger Backrest: Remove the screws and the seatbelt
carrier.
Step 7
Headrest Covers: With the headrest still in the seat, pull
the cover on with the Velcro straps to the front. Massage
the cover from top to bottom and get the cover seams to
line up with the factory seams.
Step 8
Headrest Covers: Remove the headrest from the seatback
by depressing the button on the plastic bezel and lifting up.
Step 9
Headrest Covers: Route the straps under the headrest and
connect to the Velcro sewn inside the back of the cover.
Step 10
Passenger Backrest: Open the armrest, tilt the seat
forward and pull the cover on with the Velcro straps to the
front. Tuck the cover behind the armrest and route the side
Velcro straps around the side of the seat.
Step 11
Passenger Backrest: Tuck the cover behind the armrest.
Fold the armrest into the cavity and then tuck the Velcro
straps under the armrest.
Step 12
Passenger Backrest: Fold the armrest down and find the
straps. Connect to the Velcro sewn inside the cover.
Step 13
Passenger Backrest: Fold the seat forward. The rear cargo
flap needs to be unclipped from the floor and tucked up
inside the back of the seat cover.
Step 14
Passenger Backrest: Find the Velcro on the inside of the
seat and pull around to connect to the Velcro inside the
back of the cover.
Step 15
Passenger Backrest: Tuck the cover under all of the
plastic headrest bezels, pull tabs and child restraints. (Cut
SMALL relief slits in the corners of the holes if needed).
Reinstall the seatbelt carrier.
Step 16
Passenger Backrest: Massage the cover ceiling to floor
and tuck the Velcro straps under the backrest.
Photo Unavailable
Step 17
Passenger Backrest: Fold the seat down and locate the
Velcro straps. Pull tightly and connect to the Velcro sewn
inside the back of the cover. Massage cover from ceiling to
floor and refasten Velcro to eliminate wrinkles.
Step 18
Driver Backrest: Tilt the seat forward and pull the cover
on with the Velcro straps to the front. Follow Step 13- Step
17 to complete the installation.
Step 19
Armrest Cover: Open the armrest and pull the cover on
with the Velcro straps to the front.
Step 20
Armrest Cover: Massage the cover top to bottom and tuck
the straps under the armrest.
Step 21
Armrest Cover: Fold the armrest down and pull the straps
through. Connect to the Velcro sewn inside of the cover.
Step 22
Armrest Cover: Tuck the cover under the plastic cup
holder.
Step 23
Seat Bottom: Pull the straps apart and pull the cover onto
the seat with the Velcro straps to the front. Connect one far
left and one far right to help hold the cover in place.
Step 24
Seat Bottom: Flip the seat upside down and route all the
straps to the Velcro on the tail of the cover. Make sure to
keep the cover aligned with the seat.
Step 25
Seat Bottom: Flip the seat over and find the straps located
at the seatbelt slots. Gather them and stuff them through the
seatbelt slots
Step 26
Seat Bottom: Flip the seat over and find the 1" seatbelt
slot straps. Pull them tightly and connect to the 2" Velcro
straps. Flip the seat over and massage the cover and
refasten Velcro to eliminate wrinkles. The seat bottom
cushion is flexible so the cover will seem a little loose until
reinstalled into the car.
Step 27
Seat Bottom: Reinstall the seat bottom. Feed the seatbelts
into the slots. With the front of the seat up, push the seat
back into position. You will need to get both outside
corners to connect back onto the hooks.
Step 28
Seat Bottom: Once the seat bottom is hooked in the rear
corners, push down on the front outside portions to click it
into place.