W

H

Arm and Wall Plate

01 x1 02 x1

Monitor Plate Extenders

03 x4

Step 3-1 Select monitor plate configuration Step 3-2 Assemble monitor plate and extenders

Select the configuration A , B , C, or D to use based on the measurement from step 2.If your TV hole pattern is greater than 100x100mm, attach extenders [03] to monitor plate [02]using Nut [C] and Bolt [D] .

for VESA hole pattern:75x75mm, 100x100mm.

A

VESA Pattern(WxH)

Configuration VESA Pattern

(WxH) Configuration

75mm x 75mm A C100mm x 100mm A D

B C100mm x 200mm

150mm x 150mm200mm x 100mm200mm x 200mm

C D

M-B

M-A

Use the shorter screws

M-BM-C

M-ENot for M8 screws

M-BM-A

Use the longer screws

M-B

M-E

M-FM-D

Step 3-3 Attach the brackets

(a) For Flat Back

(b) For Round Back / Extra Space

75mm100mm

75m

m10

0mm

200mm20

0mm

150m

m

150mm

200mm

200mm

100m

m

100mm

02B

D

C03

Top of TV

Top of TV

ST6.3 x 60mmLag Bolts

x2 x1 B C DA

Open-end wrench Nuts Bolts

x4 x4

03

02

Max:200x200mm /8x8"Min:75x75mm /3x3"

14"~40"

(V4)

YD1008 INSTALLATION INSTRUCTION

Bubble level X1

Hardware Included

Hardware (Wall /Product)

Philips ScrewsM6 x 15mmM6 x 30mm

Philips ScrewsM4 x 12mmM4 x 30mm

WashersØ6mmM4-5-6

Spacers L10mm

x4x4 x4x4

Philips Screws M8 x 25mm

x4 x4 x4

Spacers L5mm

x4

TV Screws / Washers

M-A M-B M-C M-D M-E M-F

Measure and note the width and the height of the square or rectangle formed from the VESA holes pattern .

Step 2 Mesure your TV pattern

2M2M

Step 1-1 Select TV screw diameter

Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fits your TV.

M6M4 M8

Correct CorrectToo LongToo Short

Step 1-2 Select TV screw length

75mm ≈ 3in.100mm ≈ 4in.150mm ≈ 6in.200mm ≈ 8in.

for VESA hole pattern:150x150mm, 200x200mm

for VESA hole pattern:100x200mm

for VESA hole pattern:200x100mm

B DC

Max:

(20KG)44LBS

Safety Caution

Must Check Before Getting Started

Installation Tools (Not Included)

BandTape

2M

SocketWrench

ScrewdriverPencil ElectrodrillStud

FinderHammerAwl Wood

Drill BitMasonryDrill Bit

Wood Stud Installation Concrete Installation

1/2"(13mm)3/8"

(10mm)5/32"

(4mm)

MAX:200mm/8"

MAX:200mm/8"

Min. 8"(203mm)

Solid concrete wall

CAUTION: DO NOT install into drywall alone.

<16mm(5/8")

Drywall with wood studs

Max:

(20KG)44LBS

No!

No!

When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.

If you have any questions, please contact us.

Please read this instruction carefully before installation.If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.

● This product is designed for use in wood stud and solid concrete wall. - DO NOT install into drywall alone.● The wall must be capable of supporting five times the weight of the TV and mount combined.● Do not apply this product to any purpose not indicated by ELIVED.● Incorrect installation may result in product damage or body injury. ELIVED shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us.

21

543

Step 4A Wall plate installation (wood stud)

4A-1

4A-2

Locate your studs. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge-to-edge stud finder.

Position the wall plate at your desired height and line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations x2.

01

4A-3

Lift and hang TV assembly onto arm and wall plate.

Secure the monitor plate to the arm and wall plate with the removed screws and washers from the previous step.

Tilting angle adjustment (+3° / -10°)

Leveling adjustment

Loosen the screws Tighten the screwsTilt the TV

+3 /-10°

Loosen the screw Tighten the screwLevel the TV

Adjust TV to your desired angle then fasten tilting screws with open-end wrench.

If needed, TV can be leveled via adjusting the screw with the open-end wrench or screwdriver.

Adjustments

B

B B

B B

Switch screen horizontally and vertically

If needed, the TV can be rotated ±90 degrees for switching screen between horizontally and vertically.

Use the open-end wrench to loosen and tighten this screw if necessary.Screwdriver can be used for adjusting the screw to secure the TV direction if need. No need to adjust this screw if the mount can hold the TV at your desired direction via the default factory setting.

Horizontal screen

±90°

Vertical screen

B

0° up

90° up

Product dimensions:

5-1

5-2

5-3

+3°/-10°

380mm68mm

200mm

100mm

200m

m

115.8mm10

0mm

210mm

143m

m

59mm

164m

m

Drill pilot holes using a 5/32 in. (4 mm) diameter drill bit.

IMPORTANT: Pilot holes must be drilled to a depth of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.

5/32

inØ

4 m

m

4A-4 01 A

A

Install wall plate using lag bolts with Socket Wrench, NO Electrodrill. Tighten the lag bolts until they are pulled firmly against the wall plate .01

01Position the wall plate at your desired height , level the wall plate and mark the pilot hole locations x2.

4B-1

A

B

Step 4B Wall plate installation (concrete or brick)

Step 5 Lift and hang TV with brackets onto wall bracket

Contact us to have these additional pieces shipped directly to you.

Concrete wall anchor 2pcs (NOT INCLUDED)

Ø10*61mm

01

A

A

A

01

01

Install wall plate using lag bolts and anchors (not included) with Socket Wrench, NO Electrodrill. Tighten the lag bolts until they are pulled firmly against the wall plate . Tighten the lag bolts until they are pulled firmly against the wall plate .

01 Level 01

01

A

4B-2

Drill pilot holes

2.75in (70 mm)

Ø 1

0 m

m

Ø 10 mm

3/8i

n

01

Remove 2 preassembled screws and washers before hang TV on to the wall bracket, and save them for using to next step.

Loosen

Tighten

B

UP

UP 2

2

Level

4B-3

No!

No!

2.75in (70 mm)

180°180°

76 8

11109