www.adelsystem.combattery care

Proteggono le batterie

Ne esaltano le prestazioni

Ne preservano la durata nel tempo

I Carica Batterie

cambiano filosofia

CB Series

Fast Recharge

Enhanced Performance

Optimized Battery Life

The New Battery Charging

Philosophy

Mission

Protect and Enhance your investment over time

Complete battery management

Technology

The CB series is a new range of battery chargers based on two strategic know-how elements:

Switching technology Adel system has a 20 year experience in design of advanced stabilized

switching technology power supplies. A battery charger based on this technology is much more efficient and much smaller and lighter than traditional linear technology battery chargers.

Micro-processor and Battery Care Unlike most other state-of-the-art battery chargers, the CB series is

equipped with a micro-processor which controls the charging process and enables several monitoring functions. The firmware implements the extended Adel battery care know-how, result of many years of experience in this field

Available Models

Input: 110 – 230 VacOut: 12 Vdc CB123ALC CB123A CB126A CB1210A

Input: 110 – 230 VacOut: 24 Vdc CB243A-LC CB243A CB245A-C CB2410A CB2410AC

Setting of charging current

Setting is possible in the range 20% - 100% of rated current

Not available on LC versions

Visual Signals

Clear indication of operation status via LED signaling

“Battery Fault” Led

Two function Led :1) Type of Charge 2) CB System Auto Diagnostic

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Min

I I I I Max

Battery Type

PE INPUTL

N

Level

Charg

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Min

I I I I Max

Battery Type

PE INPUTL

N

Level

Charg

Battery

Contact Signals

CB chargers indicate battery status and faults also via changeover contacts with galvanic isolation.

Battery faultNO–NC Output Changeover Contacts

Not available on LC versions

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Min

I I I I Max

Battery Type

PE INPUTL

N

Level

Charg

Three charging levels

CB battery chargers features three charging levels. Boost (also known as fast charging) Trickle (also known as float or maintenance charging) Recovery

The active charging mode is displayed by anLED on the front panel

Boost

Recovery

Trickle

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Battery Type

PE INPUTL

N

Level

Charg

LED display of charging mode

Recovery

Boost (fast)

Trickle

V batt

V batt

I max

1 flash per sec.

2 flashes per sec.

5 flashes per sec.

Mode switching occurs automatically

Recovery charging CB can recharge batteries even when their voltage is close to zero.

It allows recharge and complete recovery of flat batteries.

Typical charging curve for recovery of

batteries with voltage close to zero

V batt45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Battery Type

PE INPUTL

N

Level

Charg

Battery

Protections

The output is protected against short circuit and overload

Protection against deep battery discharge Protection against reverse polarity connection

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Min

I I I I Max

Battery Type

PE INPUTL

N

Level

Charg

Diagnostic checks

Check for elements in short circuit During trickle charge the quality (resistance) on the

battery connection is checked every 20 sec Appropriate voltage check, to prevent connection of

wrong battery types End of charging check Check for accidental disconnection of the battery

cables Reverse polarity check

Battery

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Min

I I I I Max

Battery Type

PE INPUTL

N

Level

Charg

Battery Diagnostic

An LED flashing sequence code allows to discriminate among various possible faults.

1 flash = Reverse polarity, wrong battery voltage

2 flashes= Disconnected battery.

3 flashes = Battery element in short circuit

5 flashes = Battery to be replaced.

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Min

I I I I Max

Battery Type

PE INPUTL

N

Level

Charg

Battery life test The smart features overviewing battery

charge status and life test diagnostics ensure high efficiency and risk-free operation

A pulse stimulation is sent to the battery by a specific circuitry. The electric signal received back in response is analysed by evaluation algorithms able to discriminate cable disconnected, sulphated battery conditions or cells in short circuit.

Battery

Pulse stimulation and assessment of battery statusCell in short

circuit

45

12

3

Battery OUTPUT

BatteryFault

Diagnosis

Min

I I I I Max

Battery Type

PE INPUTL

N

Level

Charg

Ready for charging most battery types …

Jumper for Battery Type Selection

… Ready for charging most battery types

Jumper positions / VPC:

Open Lead Acid: Trickle 2.23V Boost 2.40V Sealed Lead Acid (1): Trickle 2.25 Boost 2.40V

Sealed Lead Acid (2): Trickle 2.27 Boost 2.40V Gel: Trickle 2.30V Boost 2.40V

Optional: Ni/Cd

Applications

Gen Set

Fire Protection Systems

Security

Automatic Revolving Doors

Audio and Lighting backup

Elevators

Water Pumping

Ambient Remote Monitoring

Greenhouse Control

Cars, Motorbikes, Yachting