Suggested Tools:

• Scissors• Permanent Marker• Utility Knife• Awl

CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and equipment.

86-95 Suzuki Samurai Weathertech Cut-To-Fit Floor Mats (11AVMS) (SKU# WT-AVM)

Installation Instructions

For additional copies of these and other instructions go to:www.lowrangeoffroad and click on the “Instructions” tab.

Instructions Created by an:

Awl

The Rear Mats supplied with this set will not work in the Samurai.

Tech Tip 1These floor mats are side specific. Be sure you have the driver side mat.

Step 1Place the driver side floor mat on the driver side floor.

Step 3Remove the floor mat.

Driver Side

Passenger Side

Installing the Driver Side Floor Mat

Step 2Mark the sections that need to be removed using a permanent marker. Or simply go by memory as to which sections need removal.

Step 5Place the floor mat on a clean work surface.

Tech Tip 6These are the sections we cut away for the Samurai we were working with. However, it is totally up to you as to where you make your cuts.

Step 6Cut away the unwanted sections using common paper scissors.

Note: For best appearance, make cuts in the bottom of the grooves.

Caution: Only cut away sections you are absolutely certain you will not need. You can always remove more sections, but you cannot add them back. Take your time and do it right the first time.

Step 8Once you are satisfied with the fit, remove the floor mat and cut out the locating holes using an X-Acto knife or something similar.

Step 7Place the floor mat back in the vehicle to check for proper fit. If additional cutting is needed, remove the floor mat, make the cuts and test fit again. Repeat the test fitting and cutting procedure until you are satisfied with the fit.

Tech Tip 7Only cut out the bottom part of the hole as shown here.

Step 9Reposition the floor mat.

Step 11Peal back the floor mat and punch a hole in the carpet using an awl.

Step 10Insert a permanent marker in the hole marking the location of the floor mat anchor.

Step 12Screw the anchor into the carpet. Orient the hook of the anchor facing toward the rear of the vehicle.

Step 13Slide the mat over the anchor hook as shown.

Step 16Repeat Steps 1 through 7 on the passenger side floor mat.

Step 14Repeat Steps 8 through 13 on the other (or Right) anchor.

Step 15If installed, remove the storage tray by removing (2) bolts using a 10mm socket and sliding the tray rearward.

Installing the Passenger Side Floor Mat

Step 18If your Samurai has a tray and you want to keep it, you could make a cut in the floor mat for the tab to extend through.

Tech Tip 17Bending the tab.

Tech Tip 16 This shows the sections we removed for our installation. It is totally up to you as to which sections you remove.

Step 17This tab is for supporting the tray that mounts below the glove compartment. Our Samurai did not have the tray so we bent this tab up against the firewall.

Make Cut Here

Two rows on the bottom

One row on the inside

Step 19Another option for accommodating the tray would be to cut the floor mat as shown here.

Tech Tip 19This shows the tray installed.

Make Cut Here

Congratulations!You have successfully installed Weathertech floor mats in your Samura i . We hope t hese instructions have been helpful. If you have suggestions on how to make our instructions (or products) be t te r, p lease ema i l us a t : sales@lowrangeoffroad.com

As always, If you experience any difficulty during the installation of this product please contact Low Range Off-Road Technical Support at 801-805-6644 M-F during regular store hours. Thank you for purchasing from Low Range Off-Road.

These instructions are designed as a general installation guide. Installation of many Low Range Off-Road products require specialized skills such as metal fabrication, welding and mechanical trouble shooting. If you have any questions or are unsure about how to proceed, please contact our shop at 801-805-6644 or seek help from a competent fabricator. Using fabrication tools such as welders, torches and grinders can cause serious bodily harm and death. Please operate equipment carefully and observe proper safety procedures.

Rock crawling and off-road driving are inherently dangerous activities. Some modifications will adversely affect the on-road handling characteristics of your vehicle. All products sold by Low Range Off-Road are sold for off road use only. Any other use or application is the responsibility of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may under certain circumstances void your original dealer warranty. Modification of your vehicle may create dangerous conditions, which could cause roll-overs resulting in serious bodily injury or death. Buyers and users of these products hereby expressly assume all risks associated with any such modifications and use.

Revised 10/31/14© Copyright 2014 Low Range Off-Road, LC       All Rights Reserved