AZTECH TECHNOLOGIES PTE. LTD. 31 Ubi Road 1 #09-01 Singapore 408694. Tel : (65) 6594 2288, Fax : (65) 6749 1198. Website : www.aztech.comSPECIFICATIONS MAY CHANGE WITHOUT PRIOR NOTICE

SPECIFICATIONS SHEET

Superbly designed to provide wireless coverage throughout your household that you would surely enjoy.

Equipping you with a device that is not only appealing and stunning on its own, the WL590E brings Aztech’s wireless repeater collection into even greater heights with its 802.11ac wireless standard support, consistently providing you with an ultimate wireless experience.

WL590E750Mbps Dual Band Concurrent Wireless-AC Repeater

Product BenefitsRepeat and Extend Wireless signal throughout your home. For houses that commonly experience wireless attenuation due to the provided wireless signal of your router, Aztech WL590E easily grants you an extended range to areas with insufficient WiFi signal.

Fast and Reliable Concurrent Dual Band Wireless. To accommodate your wireless network needs further, the WL590E is assembled with a concurrent dual band wireless feature which enables you to connect your wireless devices to the frequency band which best suits your needs. May it be 2.4GHz (up to 300Mbps), or 5.0GHz (up to 450Mbps) frequency bands, the WL590E can easily directly cater to your needs.

802.11ac for a Faster Wireless Connectivity. Aztech WL590E is equipped with an 802.11ac wireless standard support which works amazingly with the 5.0GHz frequency band, allowing your wireless devices that supports the 5.0GHz band to enjoy wireless transfer speeds of up to 450Mbps anywhere in your house.

Smart LED for an Easier deployment. Designed to repeat your wireless router’s signals, Aztech WL590E is equipped with a Smart LED, a feature which allows you to determine the best possible location to deploy your device.

WPS Support for your Wireless Devices. The Aztech WL590E supports WPS connectivity. This allows you to connect your WPS enabled device to the WL590E repeater through a simple press of the WPS button on both devices.

Removes the hassle installation of wiring. With the Aztech WL590E, there is no more need to extend wide lengths of wiring in order to extend the range. Simply connect your WL590E wirelessly to your router’s wireless network and it will instantly extend your router’s wireless signal. Installation has never been this easy.

AZTECH TECHNOLOGIES PTE. LTD. 31 Ubi Road 1 #09-01 Singapore 408694. Tel : (65) 6594 2288, Fax : (65) 6749 1198. Website : www.aztech.comSPECIFICATIONS MAY CHANGE WITHOUT PRIOR NOTICE

SPECIFICATIONS SHEET WL590E750Mbps Dual Band Concurrent Wireless-AC Repeater

Deployment and Setup

Product SpecificationsHardware Features

Key Chipset:Mediatek MT7620A Network Processor + 2.4 GHz Wireless chipMediatek MT7610E 5GHz RF chip1x1 for 5.0GHz up to 450Mbps (802.11a/n/ac)

SPI FlashRom: 8M ByteDDR2 DRAM: 64M Byte

WLAN FeaturesFrequency Bands : Concurrent 2.4GHz & 5.0GHzBuilt-in-Antennas :

2x2 for 2.4GHz up to 300Mbps (802.11b/g/n)1x1 for 5.0GHz up to 450Mbps (802.11a/n/ac)

Device Tools and FeaturesWeb-Based Device Management Web-Based Firmware Upgrade (Local)WEP, WPA, WPA2 Support

Power SpecificationsSupply Voltage Range : 100VAC – 240VAC (50/60 Hz)Power Consumption : Less than 4WMax Current : 0.12A

EnvironmentsOperating Temperature : 0°C to 40°COperating Humidity : 30% to 90% Relative Humidity

(Non-Condensing)

»

»

»»

DimensionsDimensions : 105mm (L) x 58mm (W) x 42mm (H)Weight : 160 gm

Interfaces RJ45 Gigabit Ethernet (Auto MDI/MDIx)

Buttons WPS ButtonFactory Default Reset Button

SMART LED BehaviorsColour BehaviourGreen LED should be ON if WL590E is connected to Router and RSSI value is equal to HIGH.

LED should be OFF while WL590E is booting up.LED should be OFF while WL590E is doing WPS authentication.

•••

Green LED should be ON if WL590E is connected to Router and RSSI value is greater than or equal to MID.LED should be OFF while WL590E is booting up.LED should be OFF while WL590E is doing WPS authentication

•

••

Green LED should be blinking if WL590E is NOT connected to any Router.LED should be ON if WL590E is connected to Router and RSSI value is greater than or equal to LOW.LED should be OFF while WL590E is booting up.LED should be OFF while WL590E is doing WPS authentication.

••

••

Yellow LED should be ON during boot up. After fully bootup, LED will OFF.LED should be blinking for 2 mins once WPS button is pressed. LED should stop blinking and ON for 5 secs when WPS authentication is successful. Then LED should be OFF.LED should be OFF if WL590E is connected to Router.

•••

•

Smart LED Indicator

5.0GHz LED2.4GHz LED

Power LED

Ethernet Port

Reset Button

WPS Button