1/6NHA53279-0407/2015

AA Wise r Link EM5 energy meter (EER71100)

AB 5 x Wise r Link EM5 se nso r (EER71200)

AC dentification stic ers for loads

Wiser Link EM5 kit EER71000

NHA53279-04

1Contents of iser Lin it EER71000) = EM5 energy meter current sensors

2 Description

AA Power supply1 - 2: Power supply eutral Line

AB Communication ports3 - 4: Connection to P odule

5 - 6: o not use

AC Current sensors inputs

7 - 8: ensor for Load consumption or production

9 - 10: ensor for Load consumption or production

11 - 12: ensor for Load consumption or production

13 - 14: ensor for Load consumption or production

15 - 16: ensor for otal ome

AD Control keypadCancel or leave menu

avigation

isplay energy h or power ettings confirm Change

isplay main menu or otal home

AE Communication indicatorCommunication L with iser Lin P

range ashing normal operation

L off no communication

AF LCD screenotal home easurement of ain incomer

Load , , , he name of each load can be changed via embedded webpages

iser Lin application

ample of load Load

123456 kW h

Load name

Consumption value

Unit

1/5Load

Current sensor pictogram

iser Lin allows to monitor electricity consumption and electricity production.

his instruction sheet must be ept for further use.isit our website www.clipsal.com to download the technical documents of iser Lin

products.

PLEASE NOTE b his e uipment must be installed and maintained by a ualified electrician. b All relevant local, regional and national regulations must be followed during the

installation and the use of this e uipment. b he manufacturer assumes no responsibility in case of failure to follow the

instructions given in this document.

2/6NHA53279-04

3.1 Installation without extension module

3.2 Installation with extension module (see catalogue)

NOTE:a imum e tension modules can be connected.

DANGERHAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

b isconnect all power supply sources before installing this e uipment. b o not connect a on terminals of iser Lin . hese terminals can only be used for communication with iser Lin P.

Failure to follow these instructions will result in death or serious injury.

Wiring4

Installation3

1 - 2 . mm ... . mm . .m . mm3 - 4 . mm ... . mm . .m . mm7 - 89 - 1011 - 1213 - 1415 - 16

Cable delivered with sensor . .m . mm

NOTE: b he cables must be inaccessible by the users after the final installation of the product. b f there is space remaining on the right side of the product on the rail, it should be closed to prevent access.

here are electrical diagrams according to the electrical installation b Consumption only, see paragraph . b Consumption and production net metering , see paragraph . b Consumption and production gross metering , see paragraph .

NOTE: b o not mi a consumption circuit and a production circuit in one C . b o not put one, on the same load, one C dedicated for production and one C dedicated for consumption.

DANGERHAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

b isconnect all power supply sources before installing this e uipment. b o not remove the side protection stic er of iser Lin unless an e tension module is being added.

Failure to follow these instructions will result in death or serious injury.

3/6NHA53279-04

4.1 Consumption only

Wiring4

NOTE: b a imum of C sensors can be connected to each iser Lin input. b f connecting C sensors to one input, ensure the matching coloured C sensor wires are oined indicated by and . nsure both C sensors are in the same

direction as indicated by white dot AA .

NOTE: b Pass only the phase wire or neutral wire through the sensor for metering of each circuit. b o measure several circuits with the same sensor, pass the wires in the same direction through the sensor.

blue wire white wire

a imum number of wires in a sensor . mm . mm mm mm mm mm mm

ample for loads

a imum of C sensors per input

Sensors wiring for electricity consumption

4/6NHA53279-04

Sensors wiring for electricity production (net metering)

4.2 Consumption and production (net metering)

NOTE:a e sure you pass the solar inverter circuit and the utility circuit through the total home sensor to measure the net current.

Wiring4

5/6NHA53279-04

NOTE: b o not mi a consumption circuit and a production circuit in one C . b o not put one, on the same load, one C dedicated for production and one C dedicated for consumption.

Sensors wiring for electricity production (gross metering)

4.3 Consumption and production (gross metering)

Wiring4

6/6

Clipsal by Schneider Electric (Australia) Pty Ltd Port a efield oad

Gepps Crossouth Australia

Cust omer Care Centreel mail customercare.au schneider electric.coma

www.clipsal.com Clipsal Australia Pty Ltd All rights reserved.he identified trademar s and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.NHA53279-04

Clipsal Australia Ply Ltd reserves the right to change specifications, modify designs and discontinue items without incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be liable for any error therein.

Changing settings6Change the unit

123456 h

5/5

Rese t *123456 h

5/5

IP se ttings* *123456 h

5/5

About123456 h

5/5 nformation about product firmware version.

esetting consumption can only be done when the iser Lin energy meter is not connected to iser Lin P. P settings can only be done when the iser Lin energy meter is connected to iser Lin P.

Technical data8 b Power supply a ±15 % b re uency b ensor rating . A b a imum consumption A b perating temperature C ... C b easurement accuracy for active power

Class according to C b A b vervoltage category b Pollution degree b easurement category according to C b Metering: v ange h v isplay h or v inimum display . h or

b egree of protection v ront face P v Casing P b Communication with iser Lin P v it rate bit s v oltage c (not SELV) v Connection wires non polari ed cable v a imum length m b ensors connection v ominal current ... mA v oltage a, b Communication with the e tension modules v Connection e tension bus connector v upplied power supply c and . c not L .

Operation7Load 1/5

123456 h ...

Load 4/5

123456 h 123456 h

5/5

Load 1/5

123456 W ...

Load 4/5

123456 W 123456 W

5/5

Identification5

NOTE:Please ensure the uic tart uide A is completed with installation details and load descriptions and passed onto the end user.