Wire Cable & Suspension Systems - NetSuite

1www.crh.com.auwww.crh.com.auSOLUTIONS FOR TRADE

Wire Cable &Suspension Systems

November 2017

2WIRE CABLE & SUSPENSION SYSTEMS

SOLUTIONS FOR TRADE

www.crh.com.au

CONTENTSPage 3 Features & BenefitsPage 4 Wire CablePage 5 Looped CablePage 6 – 7 Kwik-Locs Page 8 – 12 Suspension Accesories Page 13 Tools and SuppliesPage 14 - 15 ApplicationsPage 16 Performance SpecificationsPage 17 Hanging at AnglesPage 18 ChainPage 19 – 34 Ceiling Suspension KitsPage 35 Suspension AccesoriesPage 36 Light Fitting Toggle Suspension Kits


SOLUTIONS FOR TRADE

www.crh.com.au

KWIK-LOC cable locks and galvanised cable are the fast & versatile way to hang static loads. Studies have shown installation time can be reduced up to 6 times compared to traditional installs using threaded rod, chain, hanger straps or other cable systems.All KWIK-LOC cable locks incorporate a length of pre-cut cable with a swaged end loop for maximum speed, efficiency and safety.

This light weight system is a major safety improvement in terms of handling and installing on site and reduces OH&S problems when installing in aerial situations when compared to heavy traditional fittings.

KWIC-LOK cable locks and galvanised wire rope are available in numerous configurations forattachment to virtually any type of building structure.

Features & Benefits


SOLUTIONS FOR TRADE

www.crh.com.auWire Cable

CableGalvanized steel cable supplied by CRH is manufactured to exact standards and statistically tested to verify the breaking strength. Using cable supplied by CRH ensures the safety and integrity of the hanging system.

Cable RollsGalvanized steel cable supplied by the roll.

Looped CableLooped Cable enhances the KWIK-LOC suspensionsystem by the addition of a pre-looped end. Once the wireCable is pulled around the anchor point and through thelooped end of the cable, it is already secured at one end,saving time at the job site. The remaining wire Cable, “thedrop”, is passed through a channel in the KWIK-LOC.

Then the wire Cable is inserted through a fastening point and back up into the second channel of the same cable lock. The locking teeth inside the cable lock engage the wire Cable which secures the equipment in place. The tensioning tool completes the adjustment.

* Ask CRH for our most recent cable Batch break weight test certificates

ITEM NAME

Gal Steel Cable - 2.5mm (3/32”) 30381 2.5mm (3/32”) +.012 / -.006” 7 x 7 152.4mGal Steel Cable - 3.2mm (1/8”) 30382 3.2mm (1/8”) +.014 / -.007” 7 x 7 152.4mGal Steel Cable - 4.8mm (3/16”) 30383 4.8mm (3/16”) +.018 / -.009” 7 x 19 76.2m

CODE CABLE DIAMETER TOLERANCE CONSTRUCTION ROLL SIZE


SOLUTIONS FOR TRADE

www.crh.com.auLooped Cable

RLC4.8-1 4.8mm (3/16) x 1 metre looped CableRLC4.8-2 4.8mm (3/16) x 2 metre looped CableRLC4.8-3 4.8mm (3/16) x 3 metre looped CableRLC4.8-4 4.8mm (3/16) x 4 metre looped CableRLC4.8-5 4.8mm (3/16) x 5 metre looped CableRLC4.8-6 4.8mm (3/16) x 6 metre looped CableRLC4.8-7 4.8mm (3/16) x 7 metre looped CableRLC4.8-8 4.8mm (3/16) x 8 metre looped CableRLC4.8-9 4.8mm (3/16) x 9 metre looped CableRLC4.8-10 4.8mm (3/16) x 10 metre looped Cable

STOCK CODE DESCRIPTION

Note: Looped cable enhances the KWIK-LOC suspension system by the addition of a pre-looped end. Once the wire is pulled around the anchor point and through the looped end of the cable, it is already secured at one end, saving time at the jobsite.

RLC6.0-1 6mm x 1 metre looped CableRLC6.0-2 6mm x 2 metre looped CableRLC6.0-3 6mm x 3 metre looped CableRLC6.0-4 6mm x 4 metre looped CableRLC6.0-5 6mm x 5 metre looped CableRLC6.0-6 6mm x 6 metre looped CableRLC6.0-7 6mm x 7 metre looped CableRLC6.0-8 6mm x 8 metre looped CableRLC6.0-9 6mm x 9 metre looped CableRLC6.0-10 6mm x 10 metre looped Cable


SOLUTIONS FOR TRADE

www.crh.com.auKWIK-LOCS

Zinc HousingOne piece die cast Zinc alloy combines major anti-corrosion properties with strength and consistent manufacturing quality.

Locking WedgesAn oil impregnated sintered steel locking wedge is seated in each of two channels. Both wedges incorporate a release pin for easy adjustment. Each wedge makes contact with the cable using serrated teeth. These teeth press onto the cable and spread the load across the length of the wedge, maximizing grip strength.

Stainless Steel SpringsEach spring is manufactured of stainless steel and assures initial engagement of the locking wedge to the wire rope.

Pull Adjustment pin back and Pass WIRE through Kwik-Loc™

Loop WIRE through anchor

Pull Adjustment pin back and Pass WIRE back through Kwik-Loc™

Always Confirm engagement of Kwik-Loc™on wire before applying load

To adjust, take the load off and pull the tail slightly to disengage teeth, then release using adjustment pin


SOLUTIONS FOR TRADE

www.crh.com.au

CODE DESCRIPTION SAFE WORKING LOAD AT 5:1

Looped Cable & KWIK-LOC Kits

KL200-1M-4.8 1m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-2M-4.8 2m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-3M-4.8 3m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-4M-4.8 4m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-5M-4.8 5m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-6M-4.8 6m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-7M-4.8 7m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-8M-4.8 8m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-9M-4.8 9m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-10M-4.8 10m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kg

KL600-1M-6.0 1m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-2M-6.0 2m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-3M-6.0 3m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-4M-6.0 4m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-5M-6.0 5m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-6M-6.0 6m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-7M-6.0 7m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-8M-6.0 8m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-9M-6.0 9m x 6mm Looped Cable & KL600 Kwik-Loc 409kgKL600-10M-6.0 10m x 6mm Looped Cable & KL600 Kwik-Loc 409kg


SOLUTIONS FOR TRADE

www.crh.com.auSuspension Accessories

Zip-Clip

CODE MATERIAL

30040 Zinc Alloy 2.5mm (3/32”) Zip-Clips are suitable for use with single or multi-tiered trapeze systems and in applications supporting such items as 3.2mm (1/8”) cable trays, baskets, water and gas pipes and chilled beams.

The Zip-Clip cable lock combined with cable and uni-strut is an efficient method of constructing a support structure. The Zip-Clip fits inside uni-sturt and has a spring loaded pawl which allows entry and passage of cable through the cable lock. Once engaged by the pawl, the cable is gripped with increasing pressure as the suspended load is increased. To ease adjustment each Zip-Clip cable lock has an integrated release pin to disengage the gripping pawl. To insure the integrity of the suspension system use cable supplied by CRH Australia.

Pack of 4 Features: • A Work Load limit of 220lbs (100kg) • Built in 5 : 1 safety factor • Fits inside strut

SUITABLE CABLE SIZE DESCRIPTION


SOLUTIONS FOR TRADE


CODE MATERIAL DESCRIPTION

30298 Zinc Alloy The KV bracket enhances the Rize Kwik-Loc suspension system by the addition of an integral bracket, which fastens the cable lock to the duct with sheet metal screws. Once the KV bracket is attached to the equipment, the wire rope “drop” is passed into the entry hole at the top of the bracket, through the cable lock, and out the exit hole at the bottom. The locking teeth inside the cable lock engage the wire rope and secure the ductwork in place. The KV100 Bracket assembly has a working load limit of up to 68kg. Suitable for 2.5mm (3/32”) Wire. Pack of 4.

30296 Zinc Plated Low Carbon Steel Eye Bolt & Nut with 3/8” thread. Thread length 38mm. Working load 65kg. Pack of 4

KV100 BracketHelps stabilize cable on sharp corners

Eye Bolt & Nut


SOLUTIONS FOR TRADE

www.crh.com.au

Corner ProtectorsHelps stabilize cable on sharp corners

Hanger PlatesZinc Plated 45˚ Hanger Plate

CODE MATERIAL DESCRIPTION

HP45K Galvanised Steel Hanger Plate.

Pack of 4

30086 Nylon Corner Protectors help to stabilise cable on sharp corners.

Pack of 4

Suspension Accessories


SOLUTIONS FOR TRADE


Con-Lock

CODE DESCRIPTION

30174 Suspension systems typically use threaded rod with washers and nuts to construct a support structure. Sizing, cutting and assembling the rods to the complementary

parts and fastening them to an anchor point can be very time consuming.

The Con-Lock system is designed for the suspension of all static loads into all concrete types including slagged, cracked, slab and even hollow pot. The Con-Lock is

designed to use a ¼” or 6 mm drill bit. Then tapped into place with a standard hammer, no claw back of the anchor is needed for installation. There is no need for any

other tools.

With a working load limit of 100lbs or 50kgs the con-Lock can be used for most electrical installations.

Pack of 4


SOLUTIONS FOR TRADE

www.crh.com.auTools and Supplies

CODE DESCRIPTION

30340 Rize Wire Cutters

Wire Cutters Rize Tensioning Tool

CODE DESCRIPTION

30341 As in all aspects of construction there may be timeswhen you need to put a little more tension on the cable than is possible with just your hands. Therefore, Rize has available a tensioning tool for these applications. Made of steel and meant to last, the tensioning tool takes all sizes of Kwik-Locs and up to 3/16 inch cable. As with all Rize products the tensioning tool is guaranteed against initial quality defects. Natural wear and tear on the tool is eventually going to happen. Rize therefore keeps ample stocks of replacement parts available when needed.

• The tensioning tool is designed to apply tension of up to 600 lbs on cable that is terminated by a Kwik-Loc.

• The tensioning tool works by holding the Kwik-Loc body and pulling the cable through the Kwik-Loc using the cam and anvil.

• The powerful lever action will tension and retension the cable in seconds.

• The tensioning tool can be used on all sizes of Kwik-Locs.


SOLUTIONS FOR TRADE

www.crh.com.auApplications

LightingThe Kwik-Loc is ideally designed for the installation of all types of lights, from HID’s to fluorescents and Cinematic flood lights. It is the fastest and easiest way to install and adjust all of your lighting suspension requirements.

ElectricalElectrical systems are being designed to minimize installation time. Typical examples are snap together busbar and basket tray systems. Kwik-Locs help carry on generating time and cost saving through to the end of the hanger installation process.

Typical electrical applications include – Busbar, cable ladder, cable tray, cable basket, channel, trunking, lighting rafts, luminaries, secondary supports, safety lines, high wattage lights, electrical cables, cctv cameras and sound systems.


SOLUTIONS FOR TRADE

www.crh.com.auApplications

Retail & SignageCRH supplies a variety of products both sold individually and in kits that lend themselves perfectly for use hanging signage. Due to the small size, the Kwik-Loc blends well in both retail and signage industries where appearance is a large factor.

MechanicalMany mechanical installations lend themselves to being supported using Kwik-Locs. The hangers can be directly fixed onto the services or used to suspend dedicated support systems. A tailor-made solution service available to devise specific solutions for a project.

Typical mechanical applications include – Water pipes, drainage pipes, gas pipes, chill beams, ceiling heating panels and radiant heaters.

DuctworkKwik-Locs are compliant with the recommendations laid down in DW/144 and Smacna. In most cases by actually wrapping the cable around the duct itself, huge savings in materials and time can be made. The result is a reduction in the number of split ring brackets and bearers used and a corresponding increase in productivity. Whether it is hanging a fan coil unit or ductwork, Kwik- Locs offer the right solution.

Typical HVAC applications include – Spiral ducting, oval ducting, rectangular ducting, fan coil units, destratification fans and extraction ductwork.


SOLUTIONS FOR TRADE

www.crh.com.auPerformance Specifications

All KWIK-LOCS have been independently tested to five times their allowable working load by one or more of the following independent laboratories:

• MELBOURNE Testing Services - NATA Approved

• SMACNA Testing & Research Insititute

• Underwriters Laboratories

• TUV Rheinland

• RADCO Inc, Long Beach CA

• New York Testing Laboratories

• NEL

• APAVE

All KWIK-LOCS have been tested to UL 1598 and are listed under File# E246601

Warnings• TO ENSURE HANGING SYSTEM INTEGRITY AND SAFETY, USE ONLY

CRH SUPPLIED CABLE.

• DO NOT USE FOR LOADS OUTSIDE THE STATED RANGE OF THE PRODUCT.

• DO NOT EXCEED THE SAFE WORKING LOAD OF THE PRODUCT.

• DO NOT USE KWIK-LOC ON COATED CABLE.

• DO NOT APPLY PAINT OR OTHER COATING.

• DO NOT APPLY LUBRICANT.

• DO NOT USE FOR LIFTING.

• KEEP THE PRODUCT CLEAN AND FREE FROM DIRT.

• REMOVE ANY DAMAGED CABLE END PRIOR TO INSERTING INTO THE KWIKLOC.

• DO NOT USE IN CHLORINATED ATMOSPHERES.

• FOR DRY LOCATIONS ONLY.

• FOR USE ON STATIC LOAD APPLICATIONS ONLY.


SOLUTIONS FOR TRADE

www.crh.com.au

CABLE SIZE VERTICAL 15° 30° 45° 60°

4.8mm (3/16”) 290 kg 280 kg 250 kg 205 kg 145 kg

3.2mm (1/8”) 43 kg 108 kg 97 kg 79 kg 55 kg

2.5mm (3/32”) 68 kg 65 kg 58 kg 47 kg 34 kg

Load 100% 96% 86% 70% 50%

Hanging at Angles

KWIK-LOCS can be used to suspend objects safely at angles up to 60 degrees from vertical.However, suspension at angles does reduce the safe working load per the table below.

Pull Adjustment pin back and Pass WIRE through Kwik-Loc™

Loop WIRE through anchor

Pull Adjustment pin back and Pass WIRE back through Kwik-Loc™

Always Confirm engagement of Kwik-Loc™ on wire before applying load

To adjust, take the load off and pull the ta il slightly to disengage teeth, then release using adjustment pin


SOLUTIONS FOR TRADE

www.crh.com.au

MATERIALCODE DESCRIPTION

KE0795-50I

Chain

Chain

6mm Regular Link Gal Commercial Chain. 60m Drum. Not suitable for industrial lifting purposes.Chain of commercial quality is suitable for general use only. It is not suitable for lifting, suspension under load, or any application Subject to control by statutory authorities or requirements.

Galvanised

KE42085 Mining Suspension Chain is supplied in a drum, 650 metre length (500kg) and is manufactured in Australia from low grade carbon steel. Suitable for the suspension of pipes or ducting, Mining Suspension Chain is proof tested to twice the Maximum Working Load and is supplied in a Hot Dipped Galvanised finish. It is not suitable for lifting purposes. A Certificate of Test and Examination can be found under the MSDS & Technical Info tab @ www.crh.com.au.

Hot dipped galvanised


SOLUTIONS FOR TRADE

www.crh.com.auCeiling Suspension Kits & Components

Ceiling Suspension Kit

CODE MATERIALDESCRIPTION

CSK20075-M10 Ceiling Suspension Kit - M10 Thread, for 75mm panel. Designed for use with wire rope. Hot Dipped GalvanisedCSK200100-M10 Ceiling Suspension Kit - M10 Thread, for 100mm panel. Designed for use with wire rope. Hot Dipped GalvanisedCSK300150-M10 Ceiling Suspension Kit - M10 Thread, for 150mm panel. Designed for use with wire rope. Hot Dipped GalvanisedCSK20075-M12 Ceiling Suspension Kit - M12 Thread, for 75mm panel. Designed for use with wire rope. Hot Dipped GalvanisedCSK200100-M12 Ceiling Suspension Kit - M12 Thread, for 100mm panel. Designed for use with wire rope. Hot Dipped GalvanisedCSK300150-M12 Ceiling Suspension Kit - M12 Thread, for 150mm panel. Designed for use with wire rope. Hot Dipped GalvanisedCSK300200-M10 Ceiling Suspension Kit - M10 Thread, for 200mm panel using a 300mm M10 rod. Hot Dipped GalvanisedCSK400250-M10 Ceiling Suspension Kit - M10 Thread, for 250mm panel using a 400mm M10 rod. Hot Dipped GalvanisedCSK400250-M102 Ceiling Suspension Kit - M10 Thread, for 250mm panel using a 400mm M10 rod. Hot Dipped Galvanised

CSK20075-M10CH CRH Ceiling Suspension Kit, HDG M10, for 75mm Panel. For Chain. Hot Dipped GalvanisedCSK200100-M10CH CRH Ceiling Suspension Kit, HDG M10, for 100mm Panel. For Chain. Hot Dipped GalvanisedCSK300150-M10CH CRH Ceiling Suspension Kit, HDG M10, for 150mm Panel. For Chain. Hot Dipped GalvanisedCSK20075-M12CH CRH Ceiling Suspension Kit, HDG M12, for 75mm Panel. For Chain. Hot Dipped GalvanisedCSK200100-M12CH CRH Ceiling Suspension Kit, HDG M12, for 100mm Panel. For Chain. Hot Dipped GalvanisedCSK300150-M12CH CRH Ceiling Suspension Kit, HDG M12, for 150mm Panel. For Chain. Hot Dipped Galvanised

A

A

B

B


SOLUTIONS FOR TRADE

www.crh.com.au

Ceiling Suspension Kit

Ceiling Suspension Kits & Components


CRCB10-200 Ceiling suspension kit. 10mm thread. Suitable for 50-100mm Panel. • Hot Dipped Galvanised • Nylon mushroom cap • White colourCRCB10-300 Ceiling suspension kit. 10mm thread. Suitable for 50-200mm Panel. • Hot Dipped Galvanised • Nylon mushroom cap • White colourCRCB12-200 Ceiling suspension kit. 12mm thread. Suitable for 50-100mm Panel. • Hot Dipped Galvanised • Nylon mushroom cap • White colourCRCB12-300 Ceiling suspension kit. 12mm thread. Suitable for 50-200mm Panel. • Hot Dipped Galvanised • Nylon mushroom cap • White colour”CRCBZ-10 Ceiling suspension kit. M10 Thread. Suitable for 50-250mm Panel. • Zinc Plated • Nylon mushroom cap • White colour

CRCBZ-10


SOLUTIONS FOR TRADE


Turnbuckles


CRH035 Turnbuckle. M10 thread. Hot dipped galvanisedSKZ-001 Turnbuckle. M10 thread. Zinc Plated.CRH034 Turnbuckle. M12 thread. Hot dipped galvanised


SOLUTIONS FOR TRADE


Threaded Rod


CRH067-200 M10 galvanised threaded rod. 200mm Hot dipped galvanisedCRH067-300 M10 galvanised threaded rod. 300mm Hot dipped galvanisedCRH067-400 M10 galvanised threaded rod 400mm Hot dipped galvanisedSKZ-002 M10 Threaded Rod. 300mm Zinc PlatedM10-1000Z M10 Threaded Rod. 1000mm Zinc PlatedCRH060-200 M12 galvanised threaded rod. 200mm Hot dipped galvanisedCRH060-300 M12 galvanised threaded rod. 300mm Hot dipped galvanisedCRH060-400 M12 galvanised threaded rod 400mm Hot dipped galvanisedM12-1000Z M12 Threaded Rod. 1000mm Zinc Plated


SOLUTIONS FOR TRADE


Tube Spacers


CRH061-75 75mm Tube Spacer. Suitable for up to M12 Thread. PVCCRH061-100 100mm Tube Spacer. Suitable for up to M12 Thread. PVCCRH061-150 150mm Tube Spacer. Suitable for up to M12 Thread. PVCCRH061-200 200mm Tube Spacer. Suitable for up to M12 Thread. PVCCRH061-250 250mm Tube Spacer. Suitable for up to M12 Thread. PVC


SOLUTIONS FOR TRADE

www.crh.com.au

Nuts, Bolts & Washers



CRH062 Washer. 62mm diameter x 2.7mm Hot Dipped GalvanisedSKZ-003 Washer. 62mm diameter x 2.7mm Zinc Plated


SOLUTIONS FOR TRADE




CRH065 Hex nut. M10x1.5 Hot Dipped GalvanisedSKZ-006 Hex nut. M10x1.5 Zinc PlatedCRH063 Hex nut. M12x1.5 Hot Dipped Galvanised


SOLUTIONS FOR TRADE

www.crh.com.au




CRH064 Hex bolt. M10x40 Hot Dipped GalvanisedSKZ-004 Hex bolt. M10x40 Zinc Plated


SOLUTIONS FOR TRADE

www.crh.com.au




CRH066 Washer. 20x11x1.4. Material: Hot dipped galvanised. Hot Dipped GalvanisedSKZ-005 Washer. 20x11x1.4. Material: Hot dipped galvanised. Zinc Plated.


SOLUTIONS FOR TRADE

www.crh.com.au

Suspension Hook


200mm

50mm

Ceiling Suspension Plate


CSH Ceiling suspension hook Zinc plated


CRH064 Ceiling Suspension Plate Hot dipped galvanised. 200 x 50 x 8mm


SOLUTIONS FOR TRADE

www.crh.com.au

CRH Suspension Bracket


CRH Suspension Bracket & Thimble


A70 CRH Suspension Bracket, H.D.G Hot Dipped GalvanisedA70T CRH Suspension Bracket With Thimble, H.D.G Hot Dipped Galvanised


SOLUTIONS FOR TRADE

www.crh.com.au



M10 Beam Clamp

MATERIAL

TKN10 M10 Rod Hanger Beam Clamp, HDG. Electrogalvanised Cast Iron


SOLUTIONS FOR TRADE

www.crh.com.au



Flanged Nut/Bolt 30mm x M16

MATERIAL

PNBM16-30 M16 Purlin Flanged Nut & Bolt. Zinc


SOLUTIONS FOR TRADE

www.crh.com.au



KL600 Kwik-Loc

MATERIAL

30344

Pressure Die-Cast Zinc & Stainless Steel.

KL600 Kwik-Loc, for 6mm Cable, 450kg Weight Rating. KWIK-LOC cable locks and galvanised Cable are the fast & versatile way to hang static loads. Studies have shown installation time can be reduced up to 6 times compared to traditional installs using threaded rod, chain, hanger straps or other cable systems.Use KWIK-LOC cable locks with a length of pre-cut cable with a swaged end loop for maximum instal-lation speed, efficiency and safety. This light weight system is a major safety improvement in terms of handling and installing on site and reduces OH&S problems when installing in aerial situations whencompared to heavy traditional fittings. KWIC-LOK cable locks and galvanised wire rope areavailable in numerous configurations for attachment to virtually any type of building structure.


SOLUTIONS FOR TRADE

www.crh.com.au



KL200 Kwik-Loc

MATERIAL

30350

Pressure Die-Cast Zinc & Stainless Steel.

KL200 Kwik-Loc, For 4.8mm Cable. 290kg Weight Rating. KWIK-LOC cable locks and galvanised Cable are the fast & versatile way to hang static loads. Studies have shown installation time can be reduced up to 6 times compared to traditional installs using threaded rod, chain, hanger straps or other cable systems.Use KWIK-LOC cable locks with a length of pre-cut cable with a swaged end loop for maximum instal-lation speed, efficiency and safety. This light weight system is a major safety improvement in terms of handling and installing on site and reduces OH&S problems when installing in aerial situations whencompared to heavy traditional fittings. KWIC-LOK cable locks and galvanised wire rope areavailable in numerous configurations for attachment to virtually any type of building structure.


SOLUTIONS FOR TRADE

www.crh.com.au



Mushroom Caps

MATERIAL

CSD-10 Mushroom Cap, M10 Thread, Surf Mist Color NylonCSD-12 Mushroom Cap, M12 Thread, Surf Mist Color Nylon


SOLUTIONS FOR TRADE

www.crh.com.au

CODE DESCRIPTION

A E389510 M10 Beam Clamp to accommodate a 10mm threaded rod Electrogalvanised Cast Iron

B E389520 M12 Beam Clamp to accommodate a 12mm threaded rod Electrogalvanised Cast Iron

Suspension Accessories

MATERIAL


SOLUTIONS FOR TRADE

www.crh.com.au

Light Fitting Toggle Suspension Kits

Light Fitting Toggle Suspension Kits

A toggle hanger is used for hanging Fluorescent/LED lights and other lighting applications. Two different lengths are available, with 1.6mm cable and are also supplied with a KL100 Kwik-Loc.


RWC2-120STG Single Toggle Kit 3050mm in length, with a 40mm x 5mm Zinc plated Toggle 1.6mm Galvanised Steel Cable

(pack of 2)

RWC2-250STG Single Toggle Kit 6350mm in length, with a 40mm x 5mm Zinc plated Toggle 1.6mm Galvanised Steel Cable

(pack of 2)

1 Nelson Street, MoorabbinVIC 3189 AUSTRALIA

Tel: 1300 274 287Fax: 1300 274 329

36www.crh.com.auwww.crh.com.auSOLUTIONS FOR TRADE

Documents

Wire Cable & Suspension Systems - NetSuite