Wintercrest Wall Mount Fireplaceassetsw.sellpoint.net/_acp_/5851/9978/asset/Wintercrest...Wintercrest Wall Mount Fireplace Model # WINWMFP ADULT ASSEMBLY REQUIRED If you have any questions

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Bayside Furnishings® Page 1 Factory No. 16366

Date 2014-08-30 Rev. 3 Factory: ZHOPAI

Wintercrest Wall Mount Fireplace Model # WINWMFP

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our toll-free customer service number and have your instructions and parts list ready to provide the model name, part name or factory number:

877-494-2536

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday Or visit our website www.baysidefurnishings.com

Or e-mail your request to: [email protected]

LOT NUMBER: DATE PURCHASED: / /

Bayside Furnishings® Page 2 Factory No. 16366

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following:

1. Read all instructions before using this fireplace.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible material, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 meters) from the front of the heater and keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.

8. Do not run power cord under carpeting. Do not cover power cord with throw rugs, runners, or the like. Arrange power cord away from traffic area and where it will not be tripped over.

9. To disconnect heater, turn controls to off, then remove plug from outlet.

10. Connect to properly grounded outlets only.

11. Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may cause an electric shock or fire, or damage the heater.

12. To prevent a possible fire, do not block firebox air intakes or exhaust in any manner. Do not operate firebox on soft surfaces, like a bed, where openings may become blocked.

13. A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.

14. There is a thermostat limiter inside the heater. When the inner temperature over heating or occur abnormal heating, the thermostat protective device would cut off power supply to avoid the fireplace damaged or risk of fire.

15. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.

16. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).

IMPORTANT SAFETY INSTRUCTIONS

There are no user serviceable parts inside the fireplace/heater. If the unit appears to malfunction, turn the unit off and unplug the unit from the wall immediately, then contact our Customer Service at 877-494-2536 for assistance, or refer service to qualified service personnel.

SAVE THESE INSTRUCTIONS

While the heater is in use, the bottom center of the fireplace can get hot to the touch, and may cause serious injury or burns. Always supervise small children around the fireplace/heater. Do not place any cloth or decorations over the heater outlet of the fireplace, or otherwise obstruct the heater outlet of the fireplace, as this may cause a fire and serious injury may result.

CAUTION

HOT


This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This heater is for use on 120 volts circuit and has a grounded plug that looks like the one illustrated on Figure 1. See Figure 1 for grounding instruction. An adapter as shown at C is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including

interference that may cause undesired operation. Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003.

GROUNDING INSTRUCTIONS

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – If it will not fit the outlet; have a proper outlet installed by qualified electrician.

FCC/IC STATEMENT


ELECTRICAL SPECIFICATIONS

HARDWARE LIST

(1) 1/4” x 1-1/4” Bolt (2) Large Lock Washer (3) Large Flat Washer (6+1 extra) (6+1 extra) (6+1 extra)

(4) 5/32” x 1” Bolt (5) Small Lock Washer (6) Small Flat Washer (7) M3.5 x 20 mm Screw (4+1 extra) (4+1 extra) (4+1 extra) (8+1 extra)

(8) M4 x 8 mm Screw (9) Large Wall Anchor (10) Small Wall Anchor (10+1 extra) (4+1 extra) (8+1 extra)

(11) M5 x 50 mm Screw (12) M4 x 20 mm Screw Touch-up Pen (4+1 extra) (8+1 extra) (1)

Tools required: Phillips screwdriver, Power Drill, Masonry Drill Bit, Hammer and Pencil (not provided).

Model No. WINWMFP

Voltage 120 V

Frequency 60 Hz

Watts 1400 W

Pre-Installation


PARTS LIST

Please read completely through the instructions and verify that all listed parts are present before beginning assembly.

C- Left Side Rail (1)

A- Wood Front Frame (1) B- Top Rail (1) D- Right Side Rail (1)

E- Left Metal Bracket (1) F- Right Metal Bracket (1) G- Table Top Base (1)

H- Electric Firebox (1) I- Mounting Bracket (1) J- Table Top Support (1) (Pre-attached on the Firebox H)

K- Front Brace (1) L- Deflector (1) M- Log Set (1) (Pre-attached on the Firebox H)

N- ‘L’-shaped Bracket (1) O- Decorative Rocks (1) P- Decorative Glasses (1) (For Flat Wood Frame only)

Q- Cable Channel (2) R- Remote Control with Batteries (1) S- Glass Front (1)

Pre-Installation (continued)


1. Unpack the unit and confirm that you have all the hardware and required parts.

2. Remove the Mounting Bracket (I) from Electric Firebox (H) by unscrewing the two screws that secure the Mounting Bracket to the top of the Electric Firebox, using a Phillips screwdriver. As shown above.

3. Find the optimal place to mount your Wall-mounted Fireplace. Consider the proper position relative to your room, placement of furniture and windows.

4. Hold the Mounting Bracket (I) up to the wall to verify the correct location and ensure that the Mounting Bracket is level. Use a pencil to mark the four mounting holes on the wall at the desired mounting location, using the Mounting Bracket (I) as a template.

5. With an electric drill (not included) on its low setting, drill 5/16 inch diameter holes to at least 2 inch deep on the marked points. NOTE: If installing the Mounting Bracket (I) to a wall stud, there is no need to drill the holes in the wood and no need for the plastic wall anchors. It is recommended to install the mounting bracket to at least one wooden stud.

Installation – Wall Mount

H

H

I

I


6. Tap 4 Large Wall Anchors (9) into the pre-drilled holes with a Hammer until they are flush with the wall.

7. Secure the Mounting Bracket (I) to the wall by using four M5 x 50 mm Screws (11). As shown.

8. Hang the Electric Firebox (H) on the hooks at the bottom of the Mounting Bracket (I), and push the

top of the Electric Firebox (H) into the Mounting Bracket. As shown.

9. Ask a friend to hold the Electric Firebox (H) into place and secure it to the Mounting Bracket (I) by refitting the two small screws which were removed in step 2. As shown.

Installation – Wall Mount (continued)

1

2I

H

H

H

I

I

9

9

9

9

11

11

11

11


NOTE: We provided the optional Decorative Rocks (O) and Decorative Glasses (P) for the ember bed. If the Log Set (M) is not to your liking, you will need to replace it by following the steps below.

10. Remove the Log Set (M) from the inset window ledge at the front of the Electric Firebox (H). As shown.

11. Arrange the desired Decorative Rocks (O) or

Decorative Glasses (P) along the inset window ledge.

NOTE: If you choose the Glass Front (S) configuration, continue to step 12. For Wood Front configuration, skip ahead to the next page.

12. Lift the Glass Front (S) into place, making sure the 2 hooks on the top back of the Glass Front (S) fit securely into the slots on the top of the Electric Firebox (H). As shown.

NOTE: It is recommended that you use two people at this stage to prevent to the Glass Front (S) or the Electric Firebox (H).

13. Secure the Glass Front (S) to the Electric Firebox (H) by fastening two M4 x 8 mm Screws (8) on both sides. As shown.


1

2

1H

S

1

S

H

1

2

H

S

8

H S

or

H

O

P

1

M

2


NOTE: If you have installed the Glass Front (S) on the firebox, disregard the following steps.

14. Locate the Wood Front Frame (A) on a flat and protective surface with the holes facing up.

15. Attach Left and Right Metal Brackets (E and F) over the pilot holes on the wood supports of the Wood Front Frame (A), using four 20 mm Screws (7) per metal bracket. Fully tighten the screws with a Phillips screwdriver. As shown above.

16. Align and attach Left and Right Side Rails (C and D) to the Wood Front Frame (A) by inserting six 1-1/4” Bolts (1) with the Large Washers (2 and 3) through the cleat holes and securely screw into place. As shown above.


A

F

7

E

7

7

7

A

C

D

321

321

321

321


17. To prevent the Decorative Rocks (O) or Decorative Glasses (P) from falling off, fasten the ‘L’-shaped

Bracket (N) under the bottom curved ledge at the front of the Electric Firebox (H), using three M4 x 8 mm Screws (8). As shown above. NOTE: Please disregard this step if you choose the Glass Front (S).

18. Lift the Wood Front assembly onto the Electric Firebox (H), making sure the 2 hooks on the top back of

the Metal Brackets (E and F) fit securely into the slots on the top of Electric Firebox (H). As shown.

NOTE: It is recommended that you use two people at this stage to prevent damage to the wood cover or the Electric Firebox (H).

19. Secure the Metal Brackets (E and F) to the Electric Firebox (H) by fastening two M4 x 8 mm Screws (8) on both sides. As shown.


1

2

H

E/F

8

H

1

2

1H

A

C

D

1

E/F

H

H

8

8

8

N


20. Position the Top Rail (B) onto the Side Rails (C and D) to finish the assembly.

21. Separate the arc cover from the Cable Channels (Q).

22. Place the flat side of Cable Channel (Q) where the Cable Channel is to be installed on the wall. Using the Cable Channel (Q) as a template, mark 4 mounting hole locations with a pencil. Using a 5/16” masonry drill bit, drill the mounting holes at least 1-1/4" deep at the marked locations.

23. Insert the Small Wall Anchors (10) into the drilled holes and lightly tap them flush with the concrete surface with rubber mallet or hammer. Securely attach the Cable Channel (Q) over the Small Wall Anchors (10) in the wall with four M4 x 20 mm Screws (12) and tighten with a Phillips screwdriver.

NOTE: If installing the Cable Channels (Q) to a wooden stud wall, there is no need to drill the holes in the wood and no need for the plastic wall anchors.

24. Repeat the same process to install the other Cable Channel (Q). Now, route the cables along the Cable Channels (Q), as shown. With all cables in place, snap the arc cover onto the Cable Channel (Q) to provide a neat appearance. You can paint the channel to match the wall color, if desired.

A

B

10 12

1-1/4" (32 mm)

QQ

10 12

10

12

10 12

Q Q



1. Unpack the unit and confirm that you have all the hardware and required parts.

2. Align and attach the Table Top Support (J) to the Table Top Base (G) by inserting four 1” Small Bolts (4) with Small Lock Washers (5) and Small Flat Washers (6) through the countersunk holes and screw into place. As shown. Fully tighten the bolts with a Phillips screwdriver.

3. Fasten the Deflector (L) to the Front Brace (K) with two M4 x 8 mm Screws (8). As shown.

4. Slide the Front Brace assembly onto the Table Top Support (J) and rest it onto the Table Top Base (G). As shown.

Installation – Table Top

G

J

654

654

K

J

L

8

8

K

J

K

G

G


5. Ask for assistance to position the Electric Firebox (H) onto Table Top Support (J) so that the top hooks of the Table Top Support (J) properly fit into the bottom slots and the back mounting holes overlap the threaded sockets on the Electric Firebox (H). As shown above.

6. Insert three M4 x 8 mm Screws (8) through the mounting holes on the Table Top Support (J) and securely screw into the Electric Firebox (H) by a Phillips screwdriver. As shown.

7. Repeat steps 10 and 11 on the Wall Mount configuration to arrange the desired Decorative Rocks (O) or Decorative Glasses (P) along the insert window ledge at the front of the Electric Firebox (H).

8. Repeat steps 12 through 19 on the Wall Mount configuration to install the Glass Front (S) or Wood

Front onto the Electric Firebox (H).

Installation – Table Top (continued)

21

J

H

J

H

8

H

J

8

8


Using the manual and remote controls

On the top right side plate of the Electric Fireplace (H) is the control panel. This panel contains the buttons to properly operate the electric fireplace. The buttons on the control panel on the side of the Electric Fireplace (H) and the Remote Control (R) function in the same way. The remote control has an effective range of up to 13 feet.

Battery Replacement

NOTE: Do not mix old and new batteries. Do not mix alkaline, standard (carbon zinc), or rechargeable (nicad, nimh, etc.) batteries. Please always dispose of batteries at a suitable recycling point.

Using the Main Power Button

The main power button (1) is located on the control panel on the right side of the electric fireplace. Pressing the main power button (1) once turns the power on. Pressing the main power button (1) again will turn the power off. If you find that none of the other buttons appear to work, check to make sure that the main power (1) is turned on.

Using the Flames Control Button

Button Press Flame State Ember Bed Color

1st press ON Amber

2nd press ON Blue

3rd press ON Amber and Blue

4th press ON Color Rotation

Operation

OPEN CLOSE

Press the flames control button (2) to turn on the ember bed and flame effect.

Pressing the flames control button (2) once turns flames on and lights the ember bed.

Pressing the flames control button (2) again will cycle through different colors of the ember bed. The color rotation mode will cycle through the 3 different color settings continuously. When using Remote Control (R), you need to press the button 7 to enter the color rotation mode. Reference the table for more detailed information.

Do not ingest batteries.

1. Non-rechargeable batteries are not to be recharged.

2. Batteries are to be inserted with the correct polarity.

3. Exhausted batteries are to be removed from the product. Battery disposal

1. Main Power Button

2. Flames Control Button

3. Heater Control Button

4. Side Light Control Button

5. Timer Function Button

6. Digital Display Unit

7. Color Rotation Button


Using the Heater Control Button

Adjusting the Ambient Side Lighting

Using the Timer Control Button

Pressing the timer control button (5) will set the timer. This interval period is shown in the display unit (6) on the control panel on the side of the electric fireplace. The set intervals are listed in the table.

No Heat Function (Demo Mode)

To turn off the heat mode, press and hold the control panel heater button for 10 seconds to enter heat lock out mode.

Ember bed lights will flash 6 times to signal the heat function is turned off and locked out.

When the heater button is pressed in lock out mode, the ember bed will flash 6 times until heating mode is turned on.

To turn on heating mode, press and hold the control panel heater button for 10 seconds, the ember bed will flash 6 times and the heat function will be restored.

Display Value Temperature Setting

0 64℉/18℃ 1 66℉/19℃

2 68℉/20℃

3 70℉/21℃

4 72℉/22℃

5 74℉/23℃

6 76℉/24℃

7 78℉/25℃

8 80℉/26℃

9 82℉/27℃ N ON

Button Press Ember Bed Color

1st press Blue

2nd press Amber

3rd press Amber and Blue

4th press Color Rotation

5th press OFF

Button Press Timer Interval Display Value

1st press 1 Hour 1

2nd press 2 Hour 2

3rd press 3 Hour 3

4th press 4 Hour 4

5th press 5 Hour 5

6th press 6 Hour 6

7th press 7 Hour 7

8th press 8 Hour 8

9th press OFF NONE

Operation (continued)

The heater control button (3) turns the heater on and off.

With the unit ON, press the control panel heater button (3) for 5 seconds and enter temperature adjustment mode. In the adjustment mode, the digital indicator (6) will flash.

Press the control panel heater button (3) to change to the desired temperature. There are 10 temperature settings. Reference the table for more detailed information.

After the temperature is selected, the digital display (6) will stay on for 10 seconds, then turn off.

Press the side light control button (4) to turn on the ambient lighting.

To change the color of the lighting press the side light control button (4) again. You can control the side lights color as described in the table. The color rotation mode will cycle through the 3 different color settings continuously.

NOTE: If this product experiences exceptionally high temperature, it may automatically stop heating. If this occurs the product should be unplugged or isolated from the main supply for a period of 30 seconds before the power is then re-supplied.


The blower motor and flame motor are pre-lubricated for a durable using time and need no further lubrication or maintenance. To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan heater. Use a soft, clean cloth that will not scratch the surface when dusting.

Use a clean soft cloth dampened with warm water to clean the fireplace surface. DO NOT use household or abrasive cleaners, as these products may damage the surface.

When cleaning the glass viewing screen use a non-abrasive damp cloth with liquid cleaner or soft soap if necessary; DO NOT use cleaning powders or any other substance with abrasives since these substances will scratch glass.

Under no circumstances should this product be operated with a broken or chipped glass panel.

Do not strike or slam the glass.

In the event that your appliance is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture.

When not in use please unplug the cord from the outlet to prevent any damage or accidental plug of the cord.

ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE

HEATER. FIRST TURN OFF THE MAIN POWER. THEN REMOVE THE ELECTRICAL PLUG FROM THE WALL OUTLET.

DO NOT USE THIS FIREPLACE INSERT IF ANY PART OF IT HAS BEEN UNDER WATER. IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE FIREBOX AND REPLACE ANY PART OF THE ELECTRICAL SYSTEM WHICH HAS BEEN UNDER WATER.

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or shipping.

The Fireplace is now ready for you to enjoy for many years to come.

We hope you enjoy your purchase for many years and thank you for your purchase!

ELECTRIC FIREBOX PARTS LIST Part Name Part Number

Flame Generator Drive Motor WINWMFP-FGDM

Heater WINWMFP-H

Blower WINWMFP-B

Log Set WINWMFP-LS

Main PCB WINWMFP-MPCB

Control Panel PCB WINWMFP-CPPCB

Flame Light PCB WINWMFP-FLPCB

Side Light PCB WINWMFP-SLPCB

Ember Bed Light PCB WINWMFP-EBLPCB

Remote Control - 6 Buttons WINWMFP-RC

CARE & MAINTENANCE INSTRUCTIONS


We are confident that you will be delighted with your Bayside Furnishings® purchase. Should this product be defective in workmanship or materials, or fail under normal use, we will repair or replace it for a period of up to one (1) year from date of purchase. Every Bayside Furnishings® product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture. This warranty gives you specific rights and you may also have other rights which vary from State to State.

Customer Service: 877-494-2536

8:30 A.M. to 4:30 P.M., Pacific Time, Monday to Friday

www.baysidefurnishings.com

TROUBLE SHOOTING GUIDE

PROBLEM SOLUTION

1. No power or function.

1a. Check that unit is plugged into a standard 120V outlet. 1b. Press power button on the control panel.

2. Main power switch lights up, but no flame effect.

2a. Open the top and back panel to check if the flame spindle has fallen off from spindle motor.

3. Have flame effect, but heater does not blow warm air.

3a. Confirm temperature setting exceeds room temperature.

3b. Try to turn on/off HEATER button several times to make sure it is in the “ON” position.

4. Heater does not work, but Power and Heater switches are in the “ON” position and thermostat is set on “HI”.

4a. Turn all switches to the “OFF” position and unplug the unit from the wall outlet for 5 minutes. After 5 minutes plug the unit back into wall outlet, and operate as normal.

5. The display unit on the control panel shows “E” and the function indicator is quick flashing, indicating it is in alarm mode.

5a. Unplug the unit from the wall outlet for 5 minutes. After 5 minutes plug the unit back into wall outlet, and operate as normal.

For replacement parts or assistance, call customer service at the above number.

QUALITY GUARANTEE

IF Y

OU

NE

ED

TO

OR

DE

R A

NY

RE

PLA

CE

ME

NT

PA

RT

S, P

LEA

SE

US

E T

HE

LIST

BE

LOW

Wintercrest W

all M

ount Fireplace (W

INW

MF

P)

*WIN

WM

FP

-1-WF

FW

ood Front F

rame

*WIN

WM

FP

-21-1SB

5/32" x 1" Bolt

*WIN

WM

FP

-2-WF

FG

Wood F

rame G

lass*W

INW

MF

P-22-S

LWS

mall Lock W

asher

*WIN

WM

FP

-2A-G

LG

lass Liner*W

INW

MF

P-23-S

FW

Sm

all Flat W

asher

*WIN

WM

FP

-3-LSR

Left Side R

ail*W

INW

MF

P-24-M

3.5x20SM

3.5 x 20 mm

Screw

*WIN

WM

FP

-4-RS

RR

ight Side R

ail*W

INW

MF

P-25-T

UP

Touch-up P

en

*WIN

WM

FP

-5-LMB

Left Metal B

racket*W

INW

MF

P-26-M

4x8SM

4 x 8 mm

Screw

*WIN

WM

FP

-6-RM

BR

ight Metal B

racket*W

INW

MF

P-27-LW

ALarge W

all Anchor

*WIN

WM

FP

-7-TR

Top R

ail*W

INW

MF

P-28-S

WA

Sm

all Wall A

nchor

*WIN

WM

FP

-7A-R

EM

Rare E

arth Magnet

*WIN

WM

FP

-29-M5x50S

M5 x 50 m

m S

crew

*WIN

WM

FP

-8-TT

BT

able Top B

ase*W

INW

MF

P-30-M

4x20SM

4 x 20 mm

Screw

*WIN

WM

FP

-9-MB

Mounting B

racket*W

INW

MF

P-C

HW

Com

plete Hardw

are for Wood P

arts

*WIN

WM

FP

-10-DD

eflector*W

INW

MF

P-C

HF

Com

plete Hardw

are for Firebox

*WIN

WM

FP

-11-FB

Front B

race*W

INW

MF

P-F

GD

MF

lame G

enerator Drive M

otor*W

INW

MF

P-12-T

TS

Table T

op Support

*WIN

WM

FP

-HH

eater*W

INW

MF

P-13-LB

L'-shaped Bracket

*WIN

WM

FP

-BB

lower

*WIN

WM

FP

-14-CC

Cable C

hannel*W

INW

MF

P-LS

Log Set

*WIN

WM

FP

-15-GF

Glass F

ront*W

INW

MF

P-M

PC

BM

ain PC

B*W

INW

MF

P-16-D

RD

ecorative Rocks

*WIN

WM

FP

-CP

PC

BC

ontrol Panel P

CB

*WIN

WM

FP

-17-DG

Decorative G

lasses*W

INW

MF

P-F

LPC

BF

lame Light P

CB

*WIN

WM

FP

-18-1 1/4B1/4" x 1-1/4" B

olt*W

INW

MF

P-S

LPC

BS

ide Light PC

B*W

INW

MF

P-19-LLW

Large Lock Washer

*WIN

WM

FP

-EB

LPC

BE

mber B

ed Light PC

B

*WIN

WM

FP

-20-LFW

Large Flat W

asher*W

INW

MF

P-R

CR

emote C

ontrolg

Documents

Wintercrest Wall Mount Fireplaceassetsw.sellpoint.net/_acp_/5851/9978/asset/Wintercrest...Wintercrest Wall Mount Fireplace Model # WINWMFP ADULT ASSEMBLY REQUIRED If you have any questions