WheelHorse light panel assembly manual 8-8012

8/7/2019 WheelHorse light panel assembly manual 8-8012

http://slidepdf.com/reader/full/wheelhorse-light-panel-assembly-manual-8-8012 1/5

PARTS LIST AND INSTRUCTIONS

WHEELHORSEPRODUCTS,INC. • SOUTH BEND,IND.

DESCRIPTION

The Model 8-0812 l ight Panel Accessory fits th eshort frame, vertical shaft, and Lawn Ranger Model1-8745.

FOR SHORT FRAME AN D VERTICAL SHAFT TRAC-TORS USE INSTRUCTIONS ON PAGE 1 AN D 2.LAWN RANGER INSTRUCTIONS BEGIN ON PAGE 2.

ASSEMBLY

1. IMPORTANT: Disconnect th e battery groundcable from th e battery. This will prevent hot sparksan d shorts.

Figure 1

ASSEMBLYLIGHTPANEL ACCESSORY

MODEL8·08122. On th e short frame models th e fuel tank must

be moved to expose th e rear of th e dash panel.

A. Loosen screw on the tank strap.B. Slide the tank forward and to th e right side

of the tractor.

Figure 2

3. Remove th e plastic plug button in th e switchhole by hitting th e plastic stems off with a screwdriver tip.

4. Connect the red wire of the light harness andthe red tail light wire to th e center terminal of th eswitch. The fused wire on the harness is connected

to the side terminal. (See Fig. 1 an d Wiring Diagrams.)5. String wires through th e switch hole an d down

through the rubber grommet. (See Fig. 2.)

Figure 3

6. The green fused wire is connected to the battery positive terminal.

7. The hood escutcheon plate can be removed bybreaking off th e stems with a screwdriver tip. Installth e tw o Ya rivets through th e hood an d reflector housing. The rivets ar e held in place with th e push-onnuts, th e slotted en d of th e nu t goes on the rivet first,se e Fig. 4 and th e Exploded View DrawilJg.



Figure 4

Figure 5

8. Insert th e socket wires, springs, and bulbs asshown in Fig. 4.

9. Mount the lens to the opening and fasten withthe four machine screws as shown in Fig. 5.

Figure 6

Figure 7

10. String th e red wire of the harness forwardunder th e left side of the engine and along the leftside of th e hood. Connect th e wire leads to th e connector as shown in Fig. 6. Fasten the wire to th ehood with th e clips provided. Any excess wire canbe looped and taped to th e inside of th e hood.

11. Mount tail light base to th e rear of the fenderas shown in Fig. 7.

12. String th e red tail light wire down inside th ehoodstand (stay behind lift ar m shaft) and back inside the tool box. Connect th e black tail light wireto th e red lead from th e switch with th e connector asshown in Fig. 8.

13. Mount fuel tank back in position. Connectbattery ground cable, an d tr y lights. If lights fail tocome on - check wiring - se e diagrams. The groundfor th e lights is transmitted through the hood latchrod; therefore, the lights may go ou t when the hoodis up.

Figure 8

INSTRUCTIONSLAWN RANGER MODEL 1·8745

ASSEMBLY

1. IMPORTANT: Disconnect the battery groundcable from the battery. This will prevent ho t sparksan d shorts.

2. Drill holes in th e rear of seat pan. (See Fig. 1.)Drill three

~ 2 Dia. holes a t th e locations shown.

Figure 1

- 2 -



3. Mount th e tail light to th e seat pa n with th e

# 10 screws, lockwashers, and nuts as shown in Fig.2. The 6" black ground wire fits under th e nut of

screw marked "A" to under th e nu t of screw marked"8". (See Fig. 2.)

Figure 2

4. Insert th e wires, springs, and bulbs in th e re-flector housing. Using th e four #6-32 screws mount the

lens and th e reflector housing to th e grill as shown in

Fig. 3. Slip one end of the 13)1" black ground wire

under th e lip of the housing an d connect th e otheren d to on e of the grill hinge bolts as shown. Attach

th e double connector to the black lead wires from th e

housing.

Figure 3

5. Connect the fused green wire of the harnessto th e positive terminal of the battery. (See Fig. 4.)

Run the red wire forward and under the wire clipprovided on the engine as shown. Connect this wireto th e connector, and fasten it to th e side of the grillwith th e wire clips. (See Fig 4.)

Figure 4

Slip th e tw o remaining ends of the wire harness

through the hole at th e base of the battery into th edash area.

6. Use a screwdriver to pry off th e plug button

covering the switch opening. (See Fig. 5.)

Pull th e wire leads of the harness through th eopening.

Figure 5

Connect th e loose re d tail light wire to th e tail

light with th e connector provided. Run th e wire un-

de r th e seat pan to th e dash area and up throughth e switch opening. Cut off th e excess length of the

tail light wire to allow about 5" through the open

ing. Skin the end of the wire and fasten the spadeterminal provided.

Connect th e tw o red leads to th e center terminalof th e switch and th e green to th e en d terminal asshown.

7. Install th e switch into the opening. Reconnectth e battery ground cable and try the switch, it ma y

have to be pulled ou t and rotated to correspond to

th e off and on position marked on the dash.

- 3 -



LIGHTS

ow""

ow""

GREEN

LIGHT SWITCH

I,

Wiring Diagram TAIL LIGHT

Short Frame and Vertical Shaft Tractors

PARTS LIST LIGHT PANEL

#8-0812(Specificotions subject to chong8 wi,hout notice.)

Parts available only through Authorixed Dealers.When ordering parts always list Part No . an d name of Part.

Item Part Na.No. No. Description Req'd .

7223 Reflector an d Socket2 7226 Wire - Light Socket 23 7227 Spring 24 7228 Bulb <#1156) 2

5 7075 lens 16 8279 Screw Self Tap #6-32 x % Special 47 100074 Terminal Spade

8 7184 Switch9 9894 Wir e - H ea dl ig ht Ground

10 7185 Wire Harne .. 111 3023 Clip 712 7618 C on ne ct or - 3 -Way 113 923003 Rivet Ys x

%Flat Head

214 7429 Nut Ys Dia . 215 8041 Base16 B042 lens 117 8043 Bulb 12 Volt 218 8044 P ad - Mo unt in g 119 909138-4 Bolt - Round Head # 10-32 x % 220 915551·4 Nut - Hex # 10-32 221 920079-4 Lockwasher # 222 6922 Connector - 2 -Wa y23 7574 Wire - Tail Light - Green24 9895 Wire - Ground Tail Light

Printed in U. S. A.

- 4 -

Wiring DiagramLawn Ranger Lawn Tractor

9

5-12-69 FORM NO . 327A



GREEN

ItemNo. No. Description Req'd.

7223 Reflector an d Socket 17226 Light 2

3156) 2

#6-32 47 100074 Terminal Spade

71849 H"adlight Ground

10

Connector 3-Way 1923003 27429 2

16 804217 2

19 22

920079-4222324

U. S. A.NO. A-SI92

Documents

WheelHorse light panel assembly manual 8-8012