View
59
Download
6
Embed Size (px)
Citation preview
weatherford.com 1 © 2002–2009 Weatherford. All rights reserved. 83.05
Cementing Products
DiamondBack™ Reamer Shoe SystemWeatherford’s DiamondBack reamer shoe system is a casing shoe that overcomes wellbore obstructions to guide casing or liners to total depth (TD). The eccentric guide nose climbs ledges and negotiates obstructions while the cutting structure reams out tight spots in the wellbore. Compatible with all casing and liner hanger assemblies, the system provides highly effective protection against unexpected or anticipated casing and liner running problems.
Applications• Runs all sizes of casing or liners to TD by reaming out tight spots, climbing
ledges, and negotiating other wellbore restrictions either through rotation or reciprocation of the pipe
• Ideal for running large-diameter casing or liners when little or no rotation is possible
Features, Advantages and Benefits• Eccentric nose design can climb ledges and negotiate other wellbore
obstructions to guide casing or liners to TD in otherwise impassable conditions.
• DiamondBack full-coverage carbide blade cutting structure, with diamond-shaped pads, facilitates both rotating and reciprocating applications to ensure safe passage of casing and liners.
• Large flow-directed ports cover the entire wellbore during rotating and reaming and prevent channeling during cement pumping.
• Weatherford Sure-Seal 3™ float valve prevents cement backflow.
• Aluminum nose enables fast drillout with PDC or tri-cone bits.
– Nose handles impact loading and high set-down weight without damage.
– Where design permits, chip breaker holes in the nose assembly create small aluminum chips to avoid “birdnesting” in the bit.
– Where applicable, the nose connection incorporates a left-hand dovetail thread that locks in place and retains radial integrity after drillout.
• Rigid standoff stabilizer blades, combined with the cutting structure, clear a path for the casing or liner and most types of rigid centralizers installed above.
Cementing Products
weatherford.com 2 © 2002–2009 Weatherford. All rights reserved. 83.05
DiamondBack™ Reamer Shoe System
Cutting StructureTungsten carbide cutting structure is set in a unique diamond pattern, facilitating both rotating and reciprocating applications.
Ledgerider ProfileField-proven Ledgerider eccentric guide nose with directional flow ports helps maneuver the casing past ledges and washouts. As the tool moves forward, it climbs over obstructions. The nose is designed to withstand impact loading and high set-down weight without damage.
DrillabilityThe aluminium nose is easily drilled with both PDC and rock bits. Where design permits, chip breaker holes in the nose assembly create small aluminum chips to avoid “birdnesting” in the bit.
Aluminum Nose Integrity ShoeLock ThreadWhere applicable, the nose connection incorporates a left-hand dovetail thread that locks in place and retains radial integrity after drillout.
Optional Float ValveReamer shoes are designed to incorporate the reliable Sure-Seal 3™ valve system, providing superior erosion resistance and backpressure holding capabilities.
Cementing Products
weatherford.com 3 © 2002–2009 Weatherford. All rights reserved. 83.05
DiamondBack™ Reamer Shoe System
Specifications
Casing Size
(in./mm) Model Number*
Tool OD
(in./mm)
Overall Length
(in./mm)
API Casing Weight Range
(lb/ft, kg/m)
API Casing Drift Range
(in./mm)
Number of
Blades
Number of
Pads
Valve Inlet Flow Area (in.2/mm2)
Nose Port Flow Area (in.2/mm2)
Back Pressure Rating,
Valve Only (psi/MPa)
3-1/2 88.90
RD034054C RD034054CV
5.500 139.70
27.126 689.00
9.3 to 12.95 13.8to19.3
2.867 to 2.625 72.82to66.68 3 6 3.14
2,0263.290 2,123
5,000 34.50
RD034055C RD034055CV
5.625 142.88
RD034056C RD034056CV
RD034056CVV
5.750 146.05
4-1/2 114.30
RD044051C RD044051CV
5.125 130.18
25.827 656.01
11.6 to 15.1 17.3to22.5
3.875 to 3.701 98.42to94.01
3 6
3.14 2,026
3.290 2,123
5,000 34.50
RD044052C RD044052CV
5.250 133.35 26.102
663.00RD044053C RD044053CV
5.375 136.53
RD044054C RD044054CV
5.500 139.70
27.126 689.00
RD044055C RD044055CV
5.625 142.88
RD044056C RD044056CV
RD044056CVV
5.750 146.05
RD044057C RD044057CV
5.875 149.23
RD044064C RD044064CV
6.500 165.10
28.465 723.00RD044065C
RD044065CV RD044065C
6.625 168.28
RD044080C RD044080CV
8.000 203.20 37.126
943.00 6 12RD044082C
RD044082CV8.250 209.55
*C = carbide cutting structure, CV = carbide cutting structure with single integral valve, CVV = carbide cutting structure with double integral valve
Cementing Products
weatherford.com 4 © 2002–2009 Weatherford. All rights reserved. 83.05
DiamondBack™ Reamer Shoe System
Specifications (continued)
Casing Size
(in./mm) Model Number*
Tool OD
(in./mm)
Overall Length
(in./mm)
API Casing Weight Range
(lb/ft, kg/m)
API Casing Drift Range
(in./mm)
Number of
Blades
Number of
Pads
Valve Inlet Flow Area (in.2/mm2)
Nose Port Flow Area (in.2/mm2)
Back Pressure Rating,
Valve Only (psi/MPa)
5 127.00
RD050056C RD050056CV
RD050056CVV
5.750 146.05
27.126 689.00
15.0 to 23.2 22.3to34.5
4.283 to 3.919 108.79to99.54
3 6
3.14 2,026
3.290 2,123
5,000 34.50
RD050061C RD050061CV
6.125 155.58
28.465 723.01RD050062C
RD050062CV RD050062CVV
6.250 158.75
RD050080C RD050080CV
8.000 203.20
37.126 943.00 6 18RD050082C
RD050082CV RD050082CVV
8.250 209.55
5-1/2 139.70
RD054060C RD054060CV
6.000 152.40
27.283 693.00
17.0 to 26.0 25.3to38.7
4.423 to 4.767 112.34to121.08
3 6
3.14 2,026
3.290 2,123
5,000 34.50
RD054062C RD054062CV
RD054062CVV
6.250 158.75
28.465 723.00
RD054063C RD054063CV
6.375 161.93
RD054064C RD054064CV
6.500 165.10
RD054072C RD054072CV
7.250 184.15
32.000 813.00
6 18
RD054074C RD054074CV
7.500 190.50 36.732
933.00RD054076C RD054076CV
7.750 196.85
RD054080C RD054080CV
8.000 203.20
37.126 943.00
RD054081C RD054081CV
8.125 206.38
RD054082C RD054082CV
RD054082CVV
8.250 209.55
*C = carbide cutting structure, CV = carbide cutting structure with single integral valve, CVV = carbide cutting structure with double integral valve
Cementing Products
weatherford.com 5 © 2002–2009 Weatherford. All rights reserved. 83.05
DiamondBack™ Reamer Shoe System
Specifications (continued)
Casing Size
(in./mm) Model Number*
Tool OD
(in./mm)
Overall Length
(in./mm)
API Casing Weight Range
(lb/ft, kg/m)
API Casing Drift Range
(in./mm)
Number of
Blades
Number of
Pads
Valve Inlet Flow Area (in.2/mm2)
Nose Port Flow Area (in.2/mm2)
Back Pressure Rating,
Valve Only (psi/MPa)
6-5/8 168.28
RD065080C RD065080CV
8.000 203.20
35.709 907.00
24.0 to 32.0 35.7to47.6
5.796 to 5.550 147.22to140.97 6 18 4.91
3,1685.84 3,768
5,000 34.50RD065082C
RD065082CV RD065082CVV
8.250 209.55
7.00 177.80
RD070080C RD070080CV
8.000 203.20
35.709 907.00
20.0 to 32.0 29.8to47.6
6.331 to 6.00 160.81to152.40 6 18 4.91
3,1685.84 3,768
5,000 34.50
RD070081C RD070081CV
8.125 206.38
RD070082C RD070082CV
RD070082CVV
8.250 209.55
RD070083C RD070083CV
8.375 212.73
RD070084C RD070084CV
8.500 215.90
RD070092C RD070092CV
9.250 234.95
RD0700106C RD0700106CV
10.750 273.05
RD0700112C RD0700112CV
11.250 285.75
7-5/8 193.68
RD075082C RD075082CV
8.250 209.55
36.220 920.00
39.7 to 42.8 59.1to63.7
6.750 to 6.376 171.45to161.95 6 18 4.91
3,1685.84 3,768
5,000 34.50
RD075084C RD075084CV
8.500 215.90
RD075090C RD075090CV
9.000 228.60
RD075092C RD075092CV
RD075092CVV
9.250 234.95
RD075094C RD075094CV
9.500 241.30
RD075095C RD075095CV
9.625 244.78
7-3/4 196.85
RD076082C RD076082CV
8.250 209.55 36.220
920.0046.1 to 46.8 68.6to69.6
6.500 to 6.345 165.10to161.16 6 18 4.91
3,1685.84 3,768
5,000 34.50RD076090C
RD076090CV9.00 228.60
*C = carbide cutting structure, CV = carbide cutting structure with single integral valve, CVV = carbide cutting structure with double integral valve
Cementing Products
weatherford.com 6 © 2002–2009 Weatherford. All rights reserved. 83.05
DiamondBack™ Reamer Shoe System
Specifications (continued)
Casing Size
(in./mm) Model Number*
Tool OD
(in./mm)
Overall Length
(in./mm)
API Casing Weight Range
(lb/ft, kg/m)
API Casing Drift Range
(in./mm)
Number of
Blades
Number of
Pads
Valve Inlet Flow Area (in.2/mm2)
Nose Port Flow Area (in.2/mm2)
Back Pressure Rating,
Valve Only (psi/MPa)
9-5/8 244.48
RD095102C RD095102CV
10.250 260.35
41.772 1,061.00
43.5 to 53.5 64.7to79.6
8.599 to 8.500 218.41to215.90 6 18 4.91
3,16813.150 8,484
5,000 34.50
RD095103C RD095103CV
10.375 263.53
RD095104C RD095104CV
10.500 266.70
RD095106C RD095106CV
10.750 273.05
RD095107C RD095107CV
10.875 276.23
RD095110C RD095110CV
11.000 279.40
RD095112C RD095112CV
11.250 285.75
RD095116C RD095116CV
11.750 298.45
RD095117C RD095117CV
11.875 301.63
RD095120C RD095120CV
12.000 304.80
9-7/8 250.83
RD097104C RD097104CV
10.500 266.70
41.772 1,061.00 62.8 to 68.8
93.5to102.48.500 215.90 6 18 4.91
3,16813.15 8,484
5,000 34.50
RD097110C RD097110CV
11.000 279.40
RD097116C RD097116CV
11.750 298.45
RD097120C RD097120CV
12.000 304.80
42.126 1,070.00
*C = carbide cutting structure, CV = carbide cutting structure with single integral valve, CVV = carbide cutting structure with double integral valve
weatherford.com 7 © 2002–2009 Weatherford. All rights reserved. 83.05
Weatherford products and services are subject to the Company’s standard terms and conditions, available on request or at weatherford.com. For more information contact an authorized Weatherford representative. Unless noted otherwise, trademarks and service marks herein are the property of Weatherford. Specifications are subject to change without notice. Weatherford sells its products and services in accordance with the terms and conditions set forth in the applicable contract between Weatherford and the client.
Cementing Products
Specifications (continued)
DiamondBack™ Reamer Shoe System
Casing Size
(in./mm) Model Number*
Tool OD
(in./mm)
Overall Length
(in./mm)
API Casing Weight Range
(lb/ft, kg/m)
API Casing Drift Range
(in./mm)
Number of
Blades
Number of
Pads
Valve Inlet Flow Area (in.2/mm2)
Nose Port Flow Area (in.2/mm2)
Back Pressure Rating,
Valve Only (psi/MPa)
10-3/4 273.05
RD106115C RD106115CV
11.625 295.28
42.126 1,070.00
55.5 to 65.7 82.6to97.8
9.625 to 9.404 244.48to238.86 6 18 4.91
3,16813.15 8,484
5,000 34.50
RD106116C RD106116CV
11.750 298.45
RD106120C RD106120CV
12.000 304.80
13-3/8 339.73
RD133144C RD133144CV
14.500 368.30
49.409 1,255.00
54.5 to 72.0 81.1to107.1
12.459 to 12.250 316.46to311.15
6 18 4.91 3,168
13.15 8,484
3,600 24.80
RD133146C RD133146CV
14.750 374.65
68.0 to 77.0 101.2to114.6
12.415 to 12.275 315.34to311.79
RD133154C RD133154CV
15.500 393.70
RD133161C RD133161CV
16.125 409.58
RD133170C RD133170V
17.000 431.80
13-5/8 346.05
RD135142C RD135142CV
14.250 361.95
49.409 1,255.00
88.2 131.3
12.250 311.15
6 18 4.91 3,168
13.15 8,484
3,600 24.80
RD135144C RD135144CV
14.500 368.30
RD135172C RD135172CV
17.250 438.15
14 355.60
RD140154C RD140154CV
15.500 393.70
106 to 120 157.7to178.6
12.313 to 12.113 312.75to307.67
16 406.40
RD160166C 16.750 425.45 48.937
1,243.0084.0 to 109.0 125.0to162.2
14.500 to 14.822 368.30to376.48 6 18 — 13.15
8,484 —RD160184C 18.500
469.90
20 508.00 RD200220C 22.00
558.8053.425 1,357.00
94.0 to 133.0 140.0to198.0
18.936 to 18.542 480.98to470.96 6 18 — 13.15
8,484 —
*C = carbide cutting structure, CV = carbide cutting structure with single integral valve, CVV = carbide cutting structure with double integral valve