WELCOME TO THE DIY LED Strip Light HubCut the “LED Strip Light” to required length.*NB, make sure to cut the strip at the designated cut and solder points. Failure to do this correctly

Cape Town Head Office: T: +27 (0) 21 788 5532 | F: +27 (0) 21 788 2637 14 Gateway Close, Capricorn Business Park, Muizenberg, 7945

Johannesburg Sales Office & Showroom: T: +27 (0) 11 794 2094 ∙ F: +27 (0) 11 794 2091 Block A, Unit 10, Kimbult Industrial Park, 9 Zeiss Rd, Laser Park, Roodepoort, 2040

Know your LED Strip Light application and begin by following the simple steps inside (please consult with your store assistant for further information or help).

WELCOME TO THE DIY LED Strip Light Hub

STEP 1Select your “LED Linear Profile” complete with accessories (end caps x2, mounting clips x2, screws x2), from the range provided.

Option 1: “Surface Shallow” [EX-BK1707D12]

Option 2: “Surface Deep” [EX-BK1715B12]

Option 3: “Surface Quarter Round” [EX-BK161610]

Option 4: Choose an alternative ”LED Linear Profile” from the brochure and request the store to order it for you.

1

Open the brochure further

STEP 2

Option 1: IP20 indoor (Do not expose to moisture)

Option 2: IP65 outdoor (Do not submerge in water)

Select your “LED Strip Light” and required length from the range provided.

CHOOSING THE LIGHT DENSITY & POWERDrive Connector (Power Feed)

Warm White 3000K Cool White 4000K Daylight 6000K

CHOOSING THE IP RATING

CHOOSING THE COLOUR TEMPERATURE

Option 1 - 60 LED / metre

4.5 watt/meter

Option 2 - 120 LED / metre

9.0 watt/meter

2

Select your “LED Strip Light Accessories” based on the choice made in step 2.

STEP 3

Drive Connector (Power Feed)

Required for powering the "LED Strip Light" from the

LED Power Supply

Optional for extending the power between multiple

"LED Strip Lights"

Middle Connector

STEP 4Select your “LED Power Supply”

60W

30W

15W

6W Powers 1m

60LED (4.5W / m) Striplight

Power Supply Wattage

120LED (9W / m) Striplight

Powers 3m

Powers 6m

Powers 12m

Powers 0.5m

Powers 1.5m

Powers 3m

Powers 6m

3

Cut the “LED Strip Light” to required length.*NB, make sure to cut the strip at the designated cut and solder points. Failure to do this correctly can cause the “LED Strip Light” to be faulty.

Manufacturing Process Mark and cut the “LED Linear Profile” including the diffuser/cover to required length using a miter block and hacksaw (sharp blade) or cutoff saw with aluminum blade. Remove the diffuser/cover and secure the end caps on either side of the profile.

Firmly clip in place the “Power Feed” accessory onto “LED Strip Light” end. *NB, always ensure that the polarity is correct: positive live (red) wire to positive solder pad and negative neutral (black) wire to negative solder pad. When linking one “LED Strip Light” to another, use the “Middle Connector” cable accessory (*NB these accessories are only required as an alternative to soldering cables directly to the solder pads).

Power Feed

Cut Points

Middle Connector

+ ++ +

- -- -

4

CONGRATULATIONS! You have completed your DIY LED Strip Light.

Ensure the “LED Linear Profile” is clean of all cutting debris and dust. Remove the protective cover from the adhesive backing of the “LED Strip Light”. Push the “Power Feed” cable already attached to the “LED Strip Light” through the end cap with the hole provided and proceed to adhere the “LED Strip” evenly and securely to the “LED Linear Profile” pushing down firmly from one side to the next.

Clip the diffuser (cover) back onto the “LED Linear Profile”. Using the mounting clips and screws provided, secure to the desired wooden surface (other surfaces may require wall plugs and screws not included). Clip the complete “LED Linear Profile” to the clips by pushing firmly, ensuring the clips have grabbed locked around the base and sides securely.

Final Connection to the “LED Power Supply” to be done by an authorized electrician for certificate of compliance (COC). “LED Linear Strip Light” will require a 220V AC supply wired from a switch point to the “LED Power Supply” and connected to the terminals on the 220V AC primary side. The “LED Linear Strip Light” is connected via the “Power Feed” to the terminals on the 12V DC secondary side. *NB, always ensure that the polarity is correct: positive live (red) wire to positive live (red) wire and negative neutral (black) wire to negative neutral (black).

Profile Underside

+-

5

2m

Accessories: 4x Metal Spring Clips 2x Metal End-Caps

SINGLE BLOCK

EX-BK653229

RECESSED APPLICATION

SURFACE MOUNTED APPLICATION

3m

SQUARE ARCH

Accessories: 1x End-Cap Without Hole 1x End-Cap With Hole 2x Metal Clips

EX-BK1715B12

3m

CORNER BLOCK

3m

FLAT BED

3m

SLIM LINE BOX

1m

HANGING RAIL


EX-BK161610


EX-BK1707D12


EX-BK1210-8

Accessories: 1x Support Bracket 2x Mounting Bracket

EX-BK1529-12

2m

Accessories: 4x Inner Tray Clips, 2x Suspension Clips 2x Suspension Cables, 2x Metal End-Caps

DOUBLE BLOCK

EX-BK507531

WITH INNER TRAY

SURFACE MOUNTED

SUSPENDED APPLICATION

SURFACE MOUNTED SURFACE MOUNTED SURFACE MOUNTED SURFACE MOUNTED

3m


SQUARE BOX

EX-BK1911B16

SURFACE MOUNTED

SUSPENDED / SURFACE MOUNTED

RECESSED

3m


FLAT BED

EX-BK2507D12

RECESSED

3m

Accessories: 1x End-Cap Without Hole 1x End-Cap With Hole 2x Metal Clip

SQUARE ARCH

EX-BK2515

RECESSED

3m


SQUARE BOX

EX-BK221211

RECESSED

1m

RECTANGLE

Accessories: 1x End-Cap Without Hole 1x End-Cap With Hole

EX-BK1911B16

RECESSED

2m

Accessories: 2 x Surface Mount Bracket 2 x Suspension Cables 2 x Metal End-Caps

DOUBLE BLOCK

EX-BK5075-29

WITH BUILT-IN TRAY


1m 2m

Accessories: 2x Suspension Cables 2x Metal End-Caps

SINGLE BLOCK

EX-BK503239


3m

Accessories: 1x End-Cap Without Hole 1x End-Cap With Hole 2x Suspension Cables

ROUND ARCH

EX-2027C17


Documents

WELCOME TO THE DIY LED Strip Light HubCut the “LED Strip Light” to required length.*NB, make sure to cut the strip at the designated cut and solder points. Failure to do this correctly