Welcome to the 1 July 2007 release of Codan's Satellite ... · Welcome to the 1st July 2007 release of Codan's Satellite Communications Products Catalogue. ... AC Mains Powered

Welcome to the 1st July 2007 release of Codan's Satellite Communications Products Catalogue. This new catalogue includes an enhanced range of BUCs and some changes in configuration. The main addition to the catalogue is the new 25W Ku-Band LBUC. The release of this catalogue coincides with the release of the next edition of the BUC System Solutions documents and the BUC and BUC Accessory Brochures. It is strongly recommended that this catalogue is read in conjunction with the BUC System Solution documents and BUC and BUC Accessory Brochures to ensure an appropriate selection of BUC products is made. A few mounting kit variants have been added. Nitin Puri Product Manager, Satellite Communications Codan Limited [email protected]

SATELLITE COMMUNICATION PRODUCTS CATALOGUE

Effective Date – 1 July 2007 i

Contents: Page: Codan Delivery Targets Codan Delivery Targets................................................................................................................ 1

C-Band Block Up Converters (BUCs) C-Band Block Up Converters, Model Numbering......................................................................... 2 C-Band Low Power Block Up Converters .................................................................................... 3 C-Band Medium Power Block Up Converters .............................................................................. 4 C-Band Block Up Converters, High Power Systems.................................................................... 5 C-Band Block Up Converters, Ordering Guide............................................................................. 6 C-Band Block Up Converters, Accessories Ordering Guide ........................................................ 7

Ku-Band Block Up Converters (BUCs) Ku-Band Block Up Converters, Model Numbering ....................................................................... 8 Ku-Band Low Power Block Up Converters................................................................................... 9 Ku-Band Medium Power Block Up Converters .......................................................................... 10 Ku-Band Block Up Converters, High Power Systems ................................................................ 11 Ku-Band Block Up Converters, Ordering Guide......................................................................... 12 Ku-Band Block Up Converters, Accessories Ordering Guide .................................................... 13 Block Up Converter Redundancy and Systems BUC Redundancy Switching Systems, Model Numbering ......................................................... 14 BUC Redundancy Switching Systems, Transmit Only ............................................................... 15 Redundancy Switching Systems, Transmit/Receive .................................................................. 16 BUC Redundancy Switching Systems, Ordering Guide............................................................. 17 C-Band 70/140MHz IF Transceivers C-Band Transceivers, Model Numbering ................................................................................... 18 C-Band Transceivers, AC Mains Powered................................................................................. 19 C-Band Transceivers, 48 VDC Powered.................................................................................... 20 C-Band Transceivers, High Power ............................................................................................. 21 C-Band Transceivers, AC Mains Powered Ordering Guide ....................................................... 22 C-Band Transceivers, 48 VDC Powered Ordering Guide .......................................................... 23 C-Band Transceivers, Accessories Ordering Guide................................................................... 24 C-Band Transceivers, Module Packages Ordering Guide ......................................................... 25 (Cont.)

SATELLITE COMMUNICATION PRODUCTS CATALOGUE

ii Effective Date – 1 July 2007

Contents: Page: Ku-Band 70/140MHz IF Transceivers Ku-Band Transceivers, Model Numbering ..................................................................................26 Ku-Band Transceivers, AC Mains Powered................................................................................27 Ku-Band Transceivers, 48 VDC Powered...................................................................................28 Ku-Band Transceivers, High Power............................................................................................29 Ku-Band Transceivers, AC Mains Powered Ordering Guide ......................................................30 Ku-Band Transceivers, 48 VDC Powered Ordering Guide .........................................................31 Ku-Band Transceivers, Accessories Ordering Guide .................................................................32 Ku-Band Transceivers, Module Packages Ordering Guide ........................................................33 70/140MHz IF Transceiver Redundancy

Transceiver Redundancy Switching Systems, Model Numbering ..............................................34 Transceiver Redundancy Switching Systems.............................................................................35 Transceiver Redundancy Switching Systems, Ordering Guide ..................................................36 Commercial Terms and Conditions

Trading Terms (International Sales) ...........................................................................................37 Conditions for Irrevocable Documentary Letter of Credit ............................................................39 International Product Warranty ...................................................................................................40 No part of this document may be reproduced, transcribed or translated into any language or transmitted in any form whatsoever without the prior written consent of Codan Limited. © Copyright 2007 Codan Limited E&OE

CODAN DELIVERY TARGETS

Effective Date – 1 July 2007 1

Codan strives to provide world's best delivery for its Satcom product range. For delivery purposes, Codan products are categorised as either core or non-core. Core Products For core products, Codan publishes a daily "Available To Sell" matrix to each of its regional sales offices. This matrix lists the available stock and production plan for these products and is used by Codan sales staff to provide customers with immediate information on delivery times. For core products, Codan's delivery target for typical commercial quantities of product is for an ex-works shipments of 10 days After Receipt of Approved Order (ARAO). A smaller quantity of each core product is normally available for shipment ex-works within a few days ARAO to meet emergency requirements. For larger quantities, the delivery will need to be reviewed against our "Available To Sell" and in discussion with the Codan factory. Non-core Products Non-core products are those that Codan offers in this catalogue that are not listed on the "Available To Sell" matrix. Delivery for these products will be quoted upon request prior to the acceptance of an approved customer order. Codan's delivery target for non-core products is that 80% of requests for these products will be shipped ex-works within 8 weeks ARO. In many cases, delivery of significantly less than 8 weeks will be achievable but cannot be confirmed until time of order. Unless otherwise indicated, products in this catalogue are "core products". All non-core products are identified with a single asterisk (*). In all circumstances, please contact your nominated Codan representative for more specific delivery information.

C-BAND BLOCK UP CONVERTERS MODEL NUMBERING The C-Band BUC model numbering system is designed to provide unambiguous identification of BUC variants and options. The C-Band BUC options and variants include: RF Frequency Band: Standard: 5,850—6,425 GHz or Extended: 5,850—6,725 GHz

RF output power: 5 W, 10 W, 20 W, 25 W, 40 W, 60 W or 120 W

RF Output Connector: WR137 waveguide or N-type coaxial

Power supply: 24 VDC or 48 VDC or AC mains

Power connector Via IF input N connector or via separate power connector

CE certification: CE certified or not certified

The BUC model number format is shown below. The model number comprises the base model number plus groups of option letters to show the particular options fitted. The first group of digits specifies the basic BUC model and its RF output power rating, the second group specifies the RF options and the third group specifies the power supply options. Finally, an additional character group is appended to indicate CE certification. Not all possible model combinations are available even though those combinations may be valid ones (e.g. the 5W C-Band BUC is not available in a CE certified version nor with a separate DC power connector). To assist with ordering, the C-Band BUC models that are available are shown in the table on page.

67PP–X/Y-AA/BB-GG-ZZ Model Extension Variant

2 Effective Date – 1 July 2007

Special variants or options - Code allocated/used only as required CE certified: - Blank for standard version - CE for CE certified version Power connector: - IF for power fed via L-Band IF input - EX for power fed via external connector Operating voltage: - 24 for 24 VDC powered - 48 for 48 VDC powered - AC for AC mains powered Frequency range: - S for Standard band (5,850—6,425 GHz) - E for Extended band (5,850—6,725 GHz) RF output connector: - N for N-type coaxial connector - W for waveguide RF output power: - two digits representing RF output power rating (e.g. 10 for 10 W) or - two digits and a letter representing RF output power rating (e.g. 12H for 120 W) Note: Where any of the model extension variants “X/Y-AA/BB-GG-ZZ” have been made BOLD

indicates that variant has an option.

C-BAND LOW POWER BLOCK UP CONVERTERS

Non-core products ial cable is not part of the standard BUC package. If you wish to use a PC to set up the BUC

RF output power Model Number5 W (Std Band) 6705-W/S-48/IF *10 W (Std Band) 6710-W/S-48/IF (-CE)20 W (Std Band) 6720-W/S-48/IF-CE

Standardfeatures

Standardaccessories

LBUCoptions

LBUCaccessories (08-05366-020) 2 m

(08-05366-030) 3 m

(08-05366-050) 5 m

(08-05366-080) 8 m

(Pass: 3,625—4,200 GHz, Reject: 5,850—6,425 GHz) (TRF-C2)(Pass: 3,400—4,200 GHz, Reject: 5,850—6,725 GHz) (TRF-C4)

8"/200mm mtg kit (6580B-8)12"/300mm mtg kit * (6580B-12)

Bold Model Extension Variants are configurable

WR137 waveguide RF output 48 VDC power via IF input

WR137 flange kit (15-40205) LBUC boom mounting kit (15-42003-000) User guide (15-44027-EN) Connector sealing kit c/w self amalgamating tape (15-40202)

N- type RF output c/w RF output coax cable, 1 m (08-05366-010) Extended band operation plus CE certification (10 W only) External DC power input connector (10 W and 20 W only) * 24 VDC operation (5 W only) *

RF output coax cable length (N-output LBUCs only):

RF output flexible waveguide, 900 mm (36") length (15-40189)

LNB, 3,4-4,2 GHz, 40 K, 60 dB gain, N output c/w flange kit (LNB-C)

Transmit Reject Filters c/w flange kit

Remote Controller 6570 c/w 50 m cable (6570-BUC-50) Remote Controller 6570 c/w 100 m cable* (6570-BUC-100) Remote Controller 6570 c/w cable for use with 6550 (6570-IU-1)

BUC to PC serial cable, 2 m ** (08-05972-002) Hand-held Controller 6560 (6560) BUC Power Supply 6580 c/w AC mains cable and:

IF Interface Unit 6550 (6550)

* ** The BUC to PC ser instead of a Hand-held Controller 6560, please order the BUC to PC serial cable separately.


C-BAND MEDIUM POWER BLOCK UP CONVERTERS


RF output power Model Number25 W (Ext Band) 6725-W/E-AC/EX-CE40 W (Ext Band) 6740-W/E-AC/EX-CE60 W (Std Band) 6760-W/S-AC/EX-CE

Standardfeatures

Standardaccessories

MBUCoptions

MBUCaccessories (08-05366-020) 2 m

(08-05366-030) 3 m

(08-05366-050) 5 m

(08-05366-080) 8 m


LNB, 3,4-4,2 GHz, 40 K, 60 dB gain, N output c/w flange kit (LNB-C) Transmit Reject Filters c/w flange kit

Remote Controller 6570 c/w 100 m cable* (6570-BUC-100) Remote Controller 6570 c/w cable for use with 6550 (6570-IU-1)

BUC to PC serial cable, 2 m ** (08-05972-002) Hand-held Controller 6560 (6560) IF Interface Unit 6550 (6550) Remote Controller 6570 c/w 50 m cable (6570-BUC-50)

(25 W and 40 W MBUCs only)

RF output coax cable length (N-output MBUCs only):


AC mains cable, 10m (08-06201-010) MBUC boom mounting kit (15-42019-000)

N- type RF output c/w RF output coax cable, 1 m (08-05366-010)

User guide (15-44027-EN) Connector sealing kit c/w self amalgamating tape (15-40202)


WR137 waveguide RF output AC power via external connector CE certification

WR137 flange kit (15-40205)



C-BAND BLOCK UP CONVERTERS HIGH POWER SYSTEMS


RF output power Ordering Code

120 W (Std Band) 6712H-W/S-AC/EX-48IF * (-CE)

Standardfeatures

Standardaccessories

SSPAoptions

Driveroptions

High Power BUC system accessories


Standard band operation (5,850—6,425 GHz) SSPA AC power 48 VDC Driver power via IF input


WR137 waveguide output

WR137 flange kit (15-40205) Accessory Kit, C-Band HP SSPA (15-40212) Interconnection and mounting kits for LBUC with C-Band HP SSPA

(15-42020-000)


CE certification (by use of external band-pass filter 78-06041)

24 VDC Driver power via IF input *


LNB, 3,4-4,2 GHz, 40 K, 60 dB gain, N output c/w flange kit (LNB-C)

Remote Controller 6570 c/w 50 m cable (6570-BUC-50) Remote Controller 6570 c/w 100 m cable* (6570-BUC-100) Remote Controller 6570 c/w cable for use with 6550 (6570-IU-1)

Transmit Reject Filters c/w flange kit

BUC to PC serial cable, 2 m ** (08-05972-002) Hand-held Controller 6560 (6560) IF Interface Unit 6550 (6550)



C-BAND BLOCK UP CONVERTERS ORDERING GUIDE

Non-core products

Std:

5,8

50—

6,42

5 G

Hz

Ext:

5,85

0—6,

725

GH

z

7,30

0 G

Hz

Sele

ctab

le

7,37

5 G

Hz

Sele

ctab

le

7,60

0 G

Hz

Sele

ctab

le

7,67

5 G

Hz

Sele

ctab

le

24 V

DC

48 V

DC

AC

6705-N/S-24/IF * 5 N * * * * IF N6705-W/S-24/IF * 5 W * * * * IF N6705-N/S-48/IF * 5 N * * * * IF N6705-W/S-48/IF * 5 W * * * * IF N6710-N/S-48/IF 10 N * * * * IF N6710-W/S-48/IF 10 W * * * * IF N6710-N/E-48/IF-CE 10 N * * * * * * IF Y6710-W/E-48/IF-CE 10 W * * * * * * IF Y6710-N/E-48/EX-CE * 10 N * * * * * * EX Y6710-W/E-48/EX-CE * 10 W * * * * * * EX Y6720-N/S-48/IF-CE 20 N * * * * IF Y6720-W/S-48/IF-CE 20 W * * * * IF Y6720-N/S-48/EX-CE * 20 N * * * * EX Y6720-W/S-48/EX-CE * 20 W * * * * EX Y6725-N/E-AC/EX-CE 25 N * * * * * * EX Y6725-W/E-AC/EX-CE 25 W * * * * * * EX Y6740-N/E-AC/EX-CE 40 N * * * * * * EX Y6740-W/E-AC/EX-CE 40 W * * * * * * EX Y6760-W/S-AC/EX-CE 60 W * * * * EX Y6712H-W/S-AC/EX-24IF * 120 W * * * * * EX/IF N6712H-W/S-AC/EX-48IF * 120 W * * * * * EX/IF N6712H-W/S-AC/EX-CE-24IF * 120 W * * * * * EX/IF Y6712H-W/S-AC/EX-CE-48IF * 120 W * * * * * EX/IF Y

LO FreqPower Supply

Pow

er C

onne

ctor

(IF N

-type

or

Exte

rnal

Con

nect

or)

CE

Cer

tific

atio

n

Model Number Out

put P

ower

(W)

Out

put (

N-ty

pe o

r Wav

egui

de)

Freq Band

*


C-BAND BLOCK UP CONVERTER ACCESSORIES ORDERING GUIDE

Non-core products

Description Comment

Part Number or Ordering Code

Cable, Coax 50 Ohm N-N Plug 1 m Incl in N-type systems 08-05366-010Cable, Coax 50 Ohm N-N Plug 2 m 08-05366-020Cable, Coax 50 Ohm N-N Plug 3 m 08-05366-030Cable, Coax 50 Ohm N-N Plug 5 m 08-05366-050Cable, Coax 50 Ohm N-N Plug 8 m 08-05366-080Cable, Serial BUC-DB9S 2 m 08-05972-002Cable, AC Mains 10m Incl in MBUC systems 08-06201-010Cable, External DC Input LBUC 5m Incl in LBUCs with ext DC connector 08-06448-005Power Supply Pole Mount Kit 8"/200mm pole Incl in 6580B systems 15-40128

Power Supply Pole Mount Kit 12"/300mm pole * 15-40147Flex Waveguide WR137, 36" c/w flange kit 15-40189

Connector Sealing Kit c/w Self-Amalgamating Tape Incl in all systems 15-40202Flange Kit, WR137 c/w Full-Thickness Gasket and 30mm screws Incl in W/G BUC systems 15-40205Accessory Kit, C-Band HP SSPA Incl in HBUC systems 15-40212LBUC Boom Mount Kit Incl in LBUC systems 15-42003-000MBUC Boom Mount Kit Included in MBUC systems 15-42019-000Kit, Mounting LBUC/ HP C-Band SSPA Incl in HBUC systems 15-42020-000Kit, Mounting LBUC/ HP SSPA Upgrade an LBUC to an HBUC 15-42068-000BUC Systems Manual Incl with all systems 15-44027-ENAdaptor N Plug to F Jack * 60-15801IF Interface Unit 6550 package 6550Hand-held Controller 6560 6560

Remote Controller 6570 package, 100m cable * 6570-BUC-100Remote Controller 6570 package, 50m cable 6570-BUC-50Remote Controller 6570 package, short cable 6570-IU-1

BUC Power Supply, 6580B package (12” pole) * 6580B-12BUC Power Supply, 6580B package (8” pole) 6580B-8Adaptor WR137 Waveguide to N Type 78-01001-005

CE Filter, Waveguide Band-Pass C-Band WR137 Incl in HBUC CE-certified systems 78-06041LNB, 3,4—4,2GHz, 40K, 60dB gain, N output LNB-CTRF, 3.625—4,200 GHz c/w flange kit TRF-C2TRF, 3.400—4,200 GHz c/w flange kit TRF-C4 *


Ku-BAND BLOCK UP CONVERTERS MODEL NUMBERING The Ku-Band BUC model numbering system is designed to provide unambiguous identification of BUC variants and options. The Ku-Band BUC options and variants include: RF Frequency Band: Standard: 14,00—14,50 GHz or Extended: 13,75—14,50 GHz

RF output power: 4 W, 8 W, 16 W, 25 W or 40 W

Power supply: 24 VDC or 48 VDC or AC mains

Power connector Via IF input N connector or via separate power connector

CE certification: CE certified or non-certified

The BUC model number format is shown below. The model number comprises the base model number plus groups of option letters to show the particular options fitted. The first group of digits specifies the basic BUC model and its RF output power rating, the second group specifies the RF options and the third group specifies the power supply options. Finally, an additional character group is appended to indicate CE certification. Not all possible model combinations are available even though those combinations may be valid ones (e.g. the 4 W Ku-Band BUC is not available in a CE non-certified version nor with a separate DC power connector). To assist with ordering, the Ku-Band BUC models that are available are shown in the table on page.

69PP–X/Y-AA/BB-GG-ZZ Model Extension Variant Special variants or options - Code allocated/used only as required


CE certification: - Blank for standard version - CE for CE certified version Power connector: - IF for power fed via L-Band IF input - EX for power fed via external connector Operating voltage: - 24 for 24 VDC powered - 48 for 48 VDC powered - AC for AC mains powered Frequency range: - S for Standard band (14,00—14,50 GHz) - E for Extended band (13,75—14,50 GHz) RF output connector: - W for waveguide RF output power: - two digits representing RF output power rating (e.g. 16 for 16 W) Note: Where any of the model extension variants “X/Y-AA/BB-GG-ZZ” have been made BOLD

indicates that variant has an option.

LOW POWER Ku-BAND BLOCK UP CONVERTERS

RF output power Model Number4 W (Ext Band) 6904-W/E-48/IF-CE *8 W (Std Band) 6908-W/S-48/IF (-CE)16 W (Std Band) 6916-W/S-48/IF25 W (Std Band) 6925-W/S-48/IF

Standardfeatures

Standardaccessories

LBUCoptions

LBUCaccessories

10,95—11,70 GHz, 75 K, 60 dB gain, N output (LNB-Ku-R1)



(Pass: 10,7—12,75 GHz, Reject: 13,75—14,50 GHz) (TRF-Ku)

8"/200mm mtg kit (6580B-8)12"/300mm mtg kit * (6580B-12)

Hand-held Controller 6560 (6560)

Remote Controller 6570 c/w cable for use with 6550 (6570-IU-1)

BUC Power Supply 6580 c/w AC mains cable and:

IF Interface Unit 6550 (6550) Remote Controller 6570 c/w 50 m cable (6570-BUC-50) Remote Controller 6570 c/w 100 m cable* (6570-BUC-100)

LNBs c/w flange kit

Transmit Reject Filter c/w flange kit

BUC to PC serial cable, 2 m ** (08-05972-002) WR75 Waveguide Adaptor (to mate metric to 6/32 UNC WR75

24 VDC operation (4 W only) *


User guide (15-44027-EN)

Extended band operation (13,75—14,50 GHz) and CE certification External DC power input connector (8 W, 16 W and 25 W only) *

Connector sealing kit c/w self amalgamating tape (15-40202)


WR75 waveguide RF output

LBUC boom mounting kit (15-42003-000)

48 VDC power via IF input CE certified (4 W)

WR75 flange kit (15-40206)

* Non-core products ** The BUC to PC serial cable is not part of the standard BUC package. If you wish to use a PC to set up the BUC instead of a Hand-held Controller 6560, please order the BUC to PC serial cable separately.


MEDIUM POWER Ku-BAND BLOCK UP CONVERTERS


RF output power Model Number16 W (Std Band) 6916-W/S-AC/EX-CE25 W (Std Band) 6925-W/S-AC/EX (-CE)

Standardfeatures

Standardaccessories

MBUCoptions

MBUCaccessories

10,95—11,70 GHz, 75 K, 60 dB gain, N output (LNB-Ku-R1)11,70—12,20 GHz, 75 K, 60 dB gain, N output (LNB-Ku-R2)12,25—12,75 GHz, 75 K, 60 dB gain, N output (LNB-Ku-R3)


Standard band operation (14,00—14,50 GHz) AC power via external connector CE certification (except 25 W extended band)


WR75 waveguide RF output

AC mains cable, 10m (08-06201-010) MBUC boom mounting kit (15-42019-000) WR75 flange kit (15-40206) User guide (15-44027-EN) Connector sealing kit c/w self amalgamating tape (15-40202)

Extended band operation (13,75—14,50 GHz)*

RF output flexible waveguide, 900 mm (36") length (15-40163) LNBs c/w flange kit


BUC to PC serial cable, 2 m ** (08-05972-002)

Remote Controller 6570 c/w 100 m cable* (6570-BUC-100) Remote Controller 6570 c/w cable for use with 6550 (6570-IU-1)

WR75 Waveguide Adaptor (to mate metric to 6/32 UNC WR75 flanges) (15-40183)

Hand-held Controller 6560 (6560) IF Interface Unit 6550 (6550) Remote Controller 6570 c/w 50 m cable (6570-BUC-50)



Ku-BAND BLOCK UP CONVERTERS HIGH POWER SYSTEMS


RF output power Ordering Code40 W (Std Band) 6940-W/S-AC/EX-CE-48IF *

Standardfeatures

Standardaccessories

HBUCoptions

Driveroptions

High Power BUC system accessories

10,95—11,70 GHz, 75 K, 60 dB gain, N output (LNB-Ku-R1)11,70—12,20 GHz, 75 K, 60 dB gain, N output (LNB-Ku-R2)12,25—12,75 GHz, 75 K, 60 dB gain, N output (LNB-Ku-R3)




WR75 waveguide output Standard band operation (14,00—14,50 GHz) SSPA AC power 48 VDC Driver power via IF input CE certified

WR75 flange kit (15-40206) Accessory Kit, Ku-Band HP SSPA (15-40213) Interconnection and mounting kits for LBUC with Ku-Band HP

SSPA (15-42021-000)

Extended band operation (13,75—14,50 GHz)

24 VDC Driver power via IF input *


LNBs c/w flange kit


BUC to PC serial cable, 2 m ** (08-05972-002) WR75 Waveguide Adaptor (to mate metric to 6/32 UNC WR75

flanges) (15-40183)

Remote Controller 6570 c/w cable for use with 6550 (6570-IU-1)

Hand-held Controller 6560 (6560) IF Interface Unit 6550 (6550) Remote Controller 6570 c/w 50 m cable (6570-BUC-50) Remote Controller 6570 c/w 100 m cable* (6570-BUC-100)



Ku-BAND BLOCK UP CONVERTERS ORDERING GUIDE

Non-core products

Std:

14,

00—

14,5

0 G

Hz

Ext:

13,7

5—14

,50

GH

z

15,4

5 G

Hz

Fixe

d

24 V

DC

48 V

DC

AC

6904-W/E-24/IF-CE * 4 W * * * IF Y6904-W/E-48/IF-CE * 4 W * * * IF Y6908-W/S-48/IF 8 W * * * IF N6908-W/E-48/IF-CE 8 W * * * IF Y6908-W/E-48/EX-CE 8 W * * * EX Y6916-W/S-48/IF 16 W * * * IF N6916-W/S-48/EX 16 W * * * EX N6916-W/S-AC/EX-CE 16 W * * * EX Y6916-W/E-AC/EX-CE 16 W * * * EX Y6925-W/S-48/IF 25 W * * * IF N6925-W/S-48/EX 25 W * * * EX N6925-W/S-AC/EX-CE 25 W * * * EX Y6925-W/E-AC/EX 25 W * * * EX N6940-W/S-AC/EX-CE-24IF * 40 W * * * * EX/IF Y6940-W/S-AC/EX-CE-48IF * 40 W * * * * EX/IF Y6940-W/E-AC/EX-CE-24IF * 40 W * * * * EX/IF Y6940-W/E-AC/EX-CE-48IF * 40 W * * * * EX/IF Y

LO Freq Power Supply

Pow

er C

onne

ctor

(IF

N-ty

pe

or E

xter

nal C

onne

ctor

)

CE

Cer

tific

atio

n

Model Number Out

put P

ower

(W)

Out

put (

W: w

aveg

uide

) Freq Band

*


Ku-BAND BLOCK UP CONVERTER ACCESSORIES ORDERING GUIDE

Non-core products

Description Comment


Cable, Serial BUC-DB9S 2 m 08-05972-002Cable, AC Mains 10m Incl in MBUC systems 08-06201-010

Cable, External DC Input LBUC 5mIncl in LBUCs with ext DC connector 08-06448-005

Power Supply Pole Mount Kit 8"/200mm pole Incl in 6580B systems 15-40128Power Supply Pole Mount Kit 12"/300mm pole * 15-40147Flex Waveguide WR75, 36" c/w flange kit 15-40163Kit, WR75 W/G Adaptor 15-40183

Connector Sealing Kit c/w Self-Amalgamating Tape Incl in all systems 15-40202

Flange Kit, WR75 with thin O-ring and 25mm screws Incl inall BUCs 15-40206Accessory Kit, Ku-Band HP SSPA Incl in HBUC systems 15-40213LBUC Boom Mount Kit Incl in LBUC systems 15-42003-000MBUC Boom Mount Kit Incl in MBUC systems 15-42019-000Kit, Mounting LBUC/ HP Ku-Band SSPA Incl in HBUC systems 15-42021-000

Kit, Mounting LBUC/ HP SSPA Upgrade an LBUC to an HBUC 15-42068-000BUC Systems Manual Incl in all systems 15-44027-ENAdaptor N Plug to F Jack * 60-15801IF Interface Unit 6550 package 6550Hand-held Controller 6560 6560Remote Controller 6570 package, 100m cable * 6570-BUC-100Remote Controller 6570 package, 50m cable 6570-BUC-50Remote Controller 6570 package, short cable 6570-IU-1BUC Power Supply, 6580B package (12” pole) * 6580B-12BUC Power Supply, 6580B package (8” pole) 6580B-8Adaptor WR75 Waveguide to N Type 78-01030LNB, 10,95—11,70GHz 75K 60dB LNB-Ku-R1LNB, 11,70—12,20GHz 75K 60dB LNB-Ku-R2LNB, 12,25—12,75GHz 75K 60dB LNB-Ku-R3TRF, 13,75—14,50GHz c/w flange kit TRF-Ku *


BUC REDUNDANCY SWITCHING SYSTEMS MODEL NUMBERING The BUC redundancy switching systems ordering code format is designed to provide unambiguous identification of the various redundancy systems available. The system configuration required depends on the particular BUC and LNB variants and system option as follows: RF Frequency band: C-Band or Ku-Band

BUC RF output connector: N-type coaxial (C-Band only) or Waveguide (C-Band and Ku-Band)

BUC model group: Segregated by model and RF power: LBUC, MBUC, HBUC etc

System type Transmit only switching or Transmit/receive switching

The BUC redundancy system model number format is shown on page below. The model number comprises the base model number plus groups of option letters/numbers to specify the particular configuration. The first group of characters specifies the fundamental frequency band of the system and the second group specifies the BUC RF output connector option. The third group specifies the BUC model group as the various BUC models have mechanical and RF output power differences. Finally, the fourth character group indicates whether the system provides transmit only switching (i.e. it provides redundancy switching for only the BUC) or transmit/receive switching (i.e. it provides redundancy switching for both the BUC and the LNB).

6586–AA/B–CC–DD Model Extension Variant


System type: - TR for Transmit/Receive (BUC+LNB) - TO for Transmit Only (BUC) BUC model and power group: - L1 for LBUCs: C-Band: 5 W, 10 W & 20 W Ku-Band: 4 W, 8 W & 16W - M1 for MBUCs: C-Band: 25 W & 40 W Ku-Band: 16 W - M2 for MBUCs: C-Band: 60 W Ku-Band: 25 W - H1 for HBUCs: C-Band: 120 W Ku-Band: 40 W BUC output connector: - N for N-type coaxial (C-Band only) - W for Waveguide (C-Band and Ku-Band) Frequency band: - C for C-Band - Ku for Ku-Band

BUC REDUNDANCY SWITCHING SYSTEMS TRANSMIT ONLY

C-Band systems Ordering Code

LBUC, waveguide output, transmit only configuration for use with 5 W to 20 W LBUCs

6586-C/W-L1-TO

MBUC, waveguide output, transmit only configuration for use with 25 W and 40 W MBUCs

6586-C/W-M1-TO

MBUC, waveguide output, transmit only configuration for use with 60 W MBUC

6586-C/W-M2-TO

High power BUC transmit only configuration for use with 120 W BUC system

6586-C/W-H1-TO

Ku-Band systems

LBUC transmit only configuration for use with 4 W to 25 W LBUCs

6586-Ku/W-L1-TO

MBUC transmit only configuration for use with 16 W MBUC

6586- Ku/W-M1-TO

MBUC transmit only configuration for use with 25 W MBUC

6586- Ku/W-M2-TO

High power BUC transmit only configuration for use with 40 W BUC system

6586- Ku/W-H1-TO

Standardaccessories

Redundancy systems

Remote Controller 6570 c/w 50 m cable, for use with Redundancy Controller 6586

6570-RC-50

options and accessories


6570-RC-100

Waveguide switch control cable (08-06103-00x)

Redundancy Controller pole mounting kit (15-40128) Redundancy Controller to BUC IF coax cables (08-05366-050) Redundancy Controller to BUC control cables (08-06099-005) Waveguide switch (C-Band 78-18005-002; Ku-Band 78-18008)

Redundancy Controller 6586 (08-06081-001) Redundancy Controller power cable (08-06201-005)

User manual (15-44027-EN) Connector sealing kit c/w self-amalgamating tape (15-40202)

Waveguide hardware to suit(flange kits, waveguide bends, spacers and blanking plate)

Off-line BUC high power termination (C-Band 78-23015/ 78-23027; Ku-Band 78-23020/ 78-23021)

BUC dual boom mounting kits


BUC REDUNDANCY SWITCHING SYSTEMS TRANSMIT/RECEIVE


LBUC, N-type output, single switch configuration for use with 5 W to 20 W LBUCs

6586-C/N-L1-TR

LBUC, waveguide output, dual switch configuration for use with 5 W to 20 W LBUCs

6586-C/W-L1-TR

MBUC, N-type output, single switch configuration for use with 25 W and 40 W MBUCs

6586-C/N-M1-TR

MBUC, waveguide output, dual switch configuration for use with 25 W and 40 W MBUCs

6586-C/W-M1-TR

MBUC, waveguide output, dual switch configuration for use with 60 W MBUC

6586-C/W-M2-TR

High power BUC dual switch configuration for use with 120 W BUC system

6586-C/W-H1-TR

Ku-Band systems

LBUC dual switch configuration for use with 4 W to 25 W LBUCs

6586-Ku/W-L1-TR

MBUC dual switch configuration for use with 16 W MBUC

6586-Ku/W-M1-TR

MBUC dual switch configuration for use with 25 W MBUC

6586-Ku/W-M2-TR

High power BUC dual switch configuration (for use with 40 W BUC system)

6586-Ku/W-H1-TR

Standardaccessories

Redundancy systems


6570-RC-50



6570-RC-100

Waveguide switch(es) (C-Band 78-18005-004 OR 78-18005-002 & 78-18005-003; Ku-Band 78-18008)

Redundancy Controller power cable (08-06201-005) Redundancy Controller pole mounting kit (15-40128) Redundancy Controller to BUC and LNB IF coax cables (08-05366-

050 and 08-05366-080)

Redundancy Controller to BUC control cables (08-06099-005)

Redundancy Controller 6586 (08-06081-001)

BUC dual boom mounting kits User manual (15-44027-EN) Connector sealing kit c/w self-amalgamating tape (15-40202)

Waveguide switch control cable(s) (08-06103-00x, 08-06104-008 & 08-06166-008)

Waveguide hardware to suit(flange kits, waveguide bends, spacers and blanking plate)

Off-line BUC high power termination (C-Band 78-23015/ 78-23027; Ku-Band 78-23020/ 78-23021)


BUC REDUNDANCY SWITCHING SYSTEMS ORDERING GUIDE

Description Comment


Cable, Coax 50 Ohm N-N Plug 0.6 m Incl in C-Band HBUC systems 08-05366-006Cable, Coax 50 Ohm N-N Plug 1 m Incl in C-Band LBUC & MBUC systems 08-05366-010Cable, Coax 50 Ohm N-N Plug 2 m Incl in C-Band HBUC systems 08-05366-020Cable, Coax 50 Ohm N-N Plug 3 m 08-05366-030Cable, Coax 50 Ohm N-N Plug 5 m Incl in all LBUC & MBUC systems 08-05366-050Cable, Coax 50 Ohm N-N Plug 8 m Incl in all Tx/ Rx systems 08-05366-080Redundancy Controller 6586 Incl in all systems 08-06081-001Cable, BUC to 6586 Incl in all systems 08-06099-005Cable, Tx Waveguide Switch Control 2 m Incl in HBUC systems 08-06103-002Cable, Tx Waveguide Switch Control 5 m Incl in LBUC & MBUC systems 08-06103-005Cable, C-Band Rx W/G Switch Control 8 m Incl in all C-band systems 08-06104-008Cable, Ku-Band Rx W/G Switch Control 8 m Incl in Ku-Band Tx/ Rx systems 08-06166-008Red Controller Power Cable AC Mains 5 m Incl in all systems 08-06201-005Cable, Dir I/O High Power BUC System 2 m Incl in HBUC systems 08-06257-002Connector Assembly Tx Only Incl in Tx only systems 08-06713-001Flange Kit WR137 Full Thickness Gasket c/w nuts Incl in all C-Band systems 15-40096Flange Kit WR229 Full Thickness Gasket c/w 16mm screws Incl in all C-Band systems 15-40106Flange Kit WR229 Half Thickness Gasket c/w 8mm screws Incl in all C-Band systems 15-40108Flange Kit WR137 Full Thickness Gasket c/w 12mm screws Incl in all C-Band W/G systems 15-40123Red Controller Mounting Kit 8” Pole Incl in all LBUC & MBUC systems 15-40128Flange Kit, WR75, Thick Groove Incl in all Ku-Band systems 15-40172Flange Kit, WR75, Thin Groove Incl in all Ku-Band HBUC systems 15-40173Flange Kit, WR75, Universal Incl in all Ku-Band systems 15-40174Kit, Conv Mounting, HP SSPAs Incl in all HP systems 15-40196-000Connector Sealing Kit c/w Self-Amalgamating Tape Incl in all systems 15-40202Flange Kit WR137 Full Thickness Gasket c/w 30mm screws

Incl in all C-Band W/G LBUC & MBUC systems 15-40205

BUC Systems Manual Incl in all systems 15-44027-ENAdaptor, N 90 degree male-female Incl in C-Band LBUC systems 60-15863-945Adaptor WR137 Waveguide to N Type Incl in C-Band LBUC & MBUC systems 78-01001-005Attenuator, 30dB, 50W N DC to 8.5 GHz Incl in C-Band LBUC systems 78-01101Waveguide Switch, WR137 (C-Band Tx) Incl in all C-Band W/G systems 78-18005-002Waveguide Switch, WR229 (C-Band Rx) Incl in all C-Band Tx/ Rx systems 78-18005-003Waveguide Switch, Dual WR229/ N-type (C-Band Tx/ Rx) Incl in all C-Band N-type systems 78-18005-004

Waveguide Switch, WR75 (Ku-Band Tx or Rx) Incl in all Ku-Band systems 78-18008Waveguide Bend 90d WR137 3” x 3” Incl in all C-Band systems 78-23011-001Waveguide termination 125W WR137 Incl in C-Band MBUC systems 78-23015Waveguide, Rigid WR75 2” Incl in all Ku-Band systems 78-23018Waveguide, Bend 90 deg WR75 3.2” x 2” Incl in all Ku-Band systems 78-23019Waveguide termination 25W WR75 Incl in Ku-Band LBUC W/G systems 78-23020Waveguide termination 75W WR75 Incl in Ku-Band MBUC & HBUC sys 78-23021Waveguide termination 300W WR137 Incl in C-Band HBUC systems 78-23027Waveguide, Jacket Flextwist WR75 18” Incl in all Ku-Band HBUC systems 78-23029Waveguide, Jacket Flextwist WR137 18” Incl in all C-Band HBUC systems 78-23048Waveguide, E-Bend 90 deg WR137 3” x 5” Incl in all 60W C-Band systems 78-23054Waveguide, H-Bend 90 deg WR75 2” x 2” Incl in all 25W Ku-Band systems 78-23055


C-BAND TRANSCEIVERS MODEL NUMBERING The C-Band transceiver ordering code system is designed to provide unambiguous identification of transceiver variants and options. The C-Band transceiver options and variants include: SSPA RF output power: 10 W, 20 W, 40 W, 60 W or 120 W

SSPA RF Output Connector: N-type coaxial or WR137 waveguide

RF Frequency Band: Tx: 5.850—6.425 GHz; Rx: 3.625—4.200 GHz or

Converter IF bandwidth: Narrow (40 MHz) or Wide (80 MHz)

Converter synthesiser: Single or Dual

Power supply: 48 VDC nominal or AC mains

CE certification: CE certified or not certified

The ordering code format is shown on page below and comprises the base code plus groups of option letters to show the particular transceiver configuration and options fitted. The base code number is an initial group of digits which specify the basic transceiver version and the SSPA RF output power rating. The second character specifies the SSPA RF output connector option, the third group specifies the Converter options, and the fourth group specifies the power supply option. Finally, a fifth character group is appended to indicate CE certification. Not all possible combinations of transceiver options are available. To assist with ordering, the transceiver versions that are available are shown in the tables on pages 22 and 23. Note that the ordering codes shown in these tables are not marked on the individual transceiver modules because they represent the code for a complete transceiver rather than the transceiver modules.

57PP–A–X/Y/Z–BB–GG Model Extension Variant

CE certification: - CE for CE certified version - Blank for non-certified version


Operating voltage: - 48 for 48 VDC powered - AC for AC mains powered Converter synthesisers: - S for Single synthesiser - D for Dual synthesiser Converter bandwidth: - N for Narrow bandwidth (40 MHz) - W for Wide bandwidth (80 MHz) Frequency band: - 2 for Band 2 (Standard): Tx: 5,850—6,425 GHz Rx: 3,625—4,200 GHz RF output connector: - N for N-type coaxial connector - W for waveguide RF output power: - two digits for RF O/P pwr (e.g. 20 for 20 W), or - two digits and a letter for RF OP pwr (e.g. 12H for 120 W) Note: Where any of the model extension variants “A-X/Y/Z-BB-GG” have been made BOLD indicates that variant has an option.

C-BAND TRANSCEIVERS AC MAINS POWERED

Non-core products


10 W 5710-N-2/N/S-AC-CE20 W 5720-N-2/N/S-AC-CE40 W 5740-N-2/N/S-AC-CE

Standardfeatures

Standard

accessories

SSPAoptions

Converteroptions

Transceiver

options andaccessories (08-05366-030 & 08-05887-030) 3 m *

(08-05366-020) 2 m (08-05366-030) 3 m

(08-05366-050) 5 m (08-05366-080) 8 m

(Pass: 3,625 – 4,200 GHz, Reject: 5,850 – 6,425

Remote Controller 5570 c/w 100 m cable * (5570-100)

LNA to Converter receive RF coax cable length:

Transmit Reject Filter c/w flange kit (TRF-C2)

Hand-held Controller 5560 (5560) Remote Controller 5570 c/w 50 m cable (5570-50)

AC Power Supply pole mtg kit suits 300 mm (12") pole * (15-40147)

SSPA to Converter RF & power/control cables:

SSPA RF output coax cable length: (N-output SSPAs only)


Wide IF bandwidth (80 MHz) option Dual synthesiser option


Waveguide output option (includes WR137 flange kit) RF Monitor Port option (10 W and 20 W SSPAs only) (15-41000-000)

AC power cable, 10 m (08-05862-010) Power supply pole mounting kit to suit 200 mm (8") pole) (15-40128) Hex Driver for Converter control panel screws (75-31400-002) C-Band transceiver reference manual (15-44001-EN)

CE certification

SSPA to Conv RF & pwr/cntrl cables, 2 m (08-05366-020 & 08-05887-020)

SSPA RF output coax cable, 1 m (08-05366-010) SSPA and Converter boom mounting kits (15-42000-000) LNA to Converter receive RF coax cable, 3 m (08-05366-030) WR229 flange kit for LNA (15-40093) PC to Converter serial cable, 2 m (08-05301-002) Power Supply to Converter DC cable, 5 m (08-05634-005)


N-type RF output Band 2 (Tx: 5.850—6.425 GHz, Rx: 3.625—4.2 GHz) Narrow IF bandwidth (40 MHz) Single synthesiser LNA (40K typical) (78-12001-001) AC Power Supply (115/230 VAC) (5582B-8)

*


C-BAND TRANSCEIVERS 48 VDC POWERED

Non-core products


10 W 5710-N-2/N/S-48-CE20 W 5720-N-2/N/S-48-CE40 W 5740-N-2/N/S-48-CE

Standardfeatures

Standard

accessories

SSPAoptions

Converteroptions

Transceiveroptions and (08-05366-030 & 08-05887-030) 3 m * accessories

(08-05366-020) 2 m (08-05366-030) 3 m

(08-05366-050) 5 m (08-05366-080) 8 m

(Pass: 3,625 – 4,200 GHz, Reject: 5,850 – 6,425

Power Supply to Converter DC cable, 5 m (08-05634-005)


N-type RF output Band 2 (transmit 5.850—6.425 GHz, receive 3.625—4.2 GHz) Narrow IF bandwidth (40 MHz) Single synthesiser LNA (40K typical) (78-12001-001) 48 VDC power

SSPA and Converter boom mounting kits (15-42000-000) LNA to Converter receive RF coax cable, 3 m (08-05366-030) WR229 flange kit for LNA (15-40093) PC to Converter serial cable, 2 m (08-05301-002)

CE certification

SSPA to Conv RF & pwr/cntrl cables, 2 m (08-05366-020 & 08-05887-020)

SSPA RF output coax cable, 1 m (08-05366-010)

Hex Driver for Converter control panel screws (75-31400-002) C-Band transceiver reference manual (15-44001-EN) Connector sealing kit c/w self amalgamating tape (15-40202)

Waveguide output option (includes WR137 flange kit) RF Monitor Port option (10 W and 20 W SSPAs only) (15-41000-000)


SSPA to Converter RF & power/control cables:

SSPA RF output coax cable length: (N-output SSPAs only)

Remote Controller 5570 c/w 50 m cable (5570-50) Remote Controller 5570 c/w 100 m cable * (5570-100)

RF output flexible waveguide, 900 mm (36") length (15-40189) LNA to Converter receive RF coax cable length:


Hand-held Controller 5560 (5560)

*


C-BAND TRANSCEIVERS HIGH POWER

Non-core products


60 W 5760-W-2/N/S-AC (-CE)120 W 5712H-W-2/N/S-AC (-CE)

Standardfeatures

Standard

accessories

Converteroptions

Transceiveroptions andaccessories (08-05366-030 & 08-05857-030) 3 m *

(08-05366-050) 5 m (08-05366-080) 8 m

(Pass: 3,625 – 4,200 GHz, Reject: 5,850 – 6,425

SSPA to Converter DC cable, 2 m (08-05961-002)


Waveguide RF output Band 2 (transmit 5.850—6.425 GHz, receive 3.625—4.2 GHz) Narrow IF bandwidth (40 MHz) Single synthesiser LNA (40K typical) (78-12001-001) AC Power Supply (104—274 VAC)

LNA to Converter receive RF coax cable, 3 m (08-05366-030) WR229 flange kit for LNA (15-40093) PC to Converter serial cable, 2 m (08-05301-002) Converter mounting kit (15-40196-000)

SSPA to Conv RF and cntrl cables, 2 m (08-05366-020 & 08-05857-020)

WR137 flange kit for SSPA (15-42030-000) SSPA pole mounting kit (15-42031-000) SSPA AC power cable, 5 m (08-06201-005)

Hex Driver for Converter control panel screws (75-31400-002) C-Band transceiver reference manual (15-44001-EN) High power SSPA reference manual (15-44011-EN) SSPA Manager software (incl with SSPA reference manual) Connector sealing kit c/w self amalgamating tape (15-40202)


CE certification (by use of external band-pass filter 78-06041) SSPA to Converter RF & power/control cables:


Remote Controller 5570 c/w 100 m cable * (5570-100)

LNA to Converter receive RF coax cable length:



*


C-BAND TRANSCEIVERS AC MAINS POWERED ORDERING GUIDE

Ban

d 2:

5.

850—

6.42

5 G

Hz

5710-N-2/N/S-AC-CE 10 N * N S Y5710-N-2/N/D-AC-CE 10 N * N D Y5710-N-2/W/D-AC-CE 10 N * W D Y5710-W-2/N/S-AC-CE 10 W * N S Y5710-W-2/N/D-AC-CE 10 W * N D Y5710-W-2/W/D-AC-CE 10 W * W D Y5720-N-2/N/S-AC-CE 20 N * N S Y5720-N-2/N/D-AC-CE 20 N * N D Y5720-N-2/W/D-AC-CE 20 N * W D Y5720-W-2/N/S-AC-CE 20 W * N S Y5720-W-2/N/D-AC-CE 20 W * N D Y5720-W-2/W/D-AC-CE 20 W * W D Y5740-N-2/N/S-AC-CE 40 N * N S Y5740-N-2/N/D-AC-CE 40 N * N D Y5740-N-2/W/D-AC-CE 40 N * W D Y5740-W-2/N/S-AC-CE 40 W * N S Y5740-W-2/N/D-AC-CE 40 W * N D Y5740-W-2/W/D-AC-CE 40 W * W D Y5760-W-2/N/S-AC 60 W * N S N5760-W-2/N/D-AC 60 W * N D N5760-W-2/W/D-AC 60 W * W D N5760-W-2/N/S-AC-CE 60 W * N S Y5760-W-2/N/D-AC-CE 60 W * N D Y5760-W-2/W/D-AC-CE 60 W * W D Y5712H-W-2/N/S-AC 120 W * N S N5712H-W-2/N/D-AC 120 W * N D N5712H-W-2/W/D-AC 120 W * W D N5712H-W-2/N/S-AC-CE 120 W * N S Y5712H-W-2/N/D-AC-CE 120 W * N D Y5712H-W-2/W/D-AC-CE 120 W * W D Y

IF B

andw

idth

(Nar

row

: 40

MH

z, W

ide:

80

MH

z)

Synt

hesi

ser (

sing

le o

r Dua

l)

CE

Cer

tific

atio

n

Ordering Code Out

put P

ower

(W)

Out

put (

N-ty

pe o

r w

aveg

uide

)

Transmit Band


C-BAND TRANSCEIVERS 48 VDC POWERED ORDERING GUIDE

Ban

d 2:

5.8

50—

6.42

5 G

Hz

5710-N-2/N/S-48-CE 10 N * N S Y5710-N-2/N/D-48-CE 10 N * N D Y5710-N-2/W/D-48-CE 10 N * W D Y5710-W-2/N/S-48-CE 10 W * N S Y5710-W-2/N/D-48-CE 10 W * N D Y5710-W-2/W/D-48-CE 10 W * W D Y5720-N-2/N/S-48-CE 20 N * N S Y5720-N-2/N/D-48-CE 20 N * N D Y5720-N-2/W/D-48-CE 20 N * W D Y5720-W-2/N/S-48-CE 20 W * N S Y5720-W-2/N/D-48-CE 20 W * N D Y5720-W-2/W/D-48-CE 20 W * W D Y5740-N-2/N/S-48-CE 40 N * N S Y5740-N-2/N/D-48-CE 40 N * N D Y5740-N-2/W/D-48-CE 40 N * W D Y5740-W-2/N/S-48-CE 40 W * N S Y5740-W-2/N/D-48-CE 40 W * N D Y5740-W-2/W/D-48-CE 40 W * W D Y

IF B

andw

idth

(Nar

row

: 40

MH

z, W

ide:

80

MH

z)

Synt

hesi

ser (

sing

le o

r Dua

l)

CE

Cer

tific

atio

n

Ordering Code Out

put P

ower

(W)

Out

put (

N-ty

pe o

r wav

egui

de)

Transmit Band


C-BAND TRANSCEIVERS ACCESSORIES ORDERING GUIDE

Non-core products

Description Comment


Cable, Serial Conv-PC, (DB-9S) 2 m Incl in transceiver system 08-05301-002Cable, Coax 50 Ohm N-N Plug 1 m Incl in N-type transceiver system 08-05366-010Cable, Coax 50 Ohm N-N Plug 2 m 08-05366-020Cable, Coax 50 Ohm N-N Plug 3 m Incl in transceiver system 08-05366-030Cable, Coax 50 Ohm N-N Plug 5 m 08-05366-050Cable, Coax 50 Ohm N-N Plug 8 m 08-05366-080Cable, DC Power (Rd/Bk) 5 m Incl in LP transceiver system 08-05634-005Cable, HP SSPA to Converter 2,0 m Incl in HP transceiver system 08-05857-020Cable, HP SSPA to Converter 3,0 m * 08-05857-030Cable, HP SSPA to Converter 4,0 m * 08-05857-040Cable, AC 3 core 24/0, 20 8 m Incl in LP AC transceiver system 08-05862-010Cable, Converter to SSPA Connector 2 m Incl in transceiver system 08-05887-020Cable, Converter to SSPA Connector 3 m * 08-05887-030Cable, Converter to SSPA Connector 4 m * 08-05887-040Cable, DC Pwr SSPA - Converter 2 m Incl in transceiver system 08-05961-002Cable, DC Pwr SSPA - Converter 3 m * 08-05961-003Cable, DC Pwr SSPA - Converter 4 m * 08-05961-004Cable, AC Mains 5 m Incl in HP transceiver system 08-06201-005Flange Kit, WR229 Half Gasket c/w nuts Incl in transceiver system 15-40093Power Supply Pole Mount Kit 8"/200 mm pole Incl in LP AC transceiver system 15-40128Power Supply Pole Mount Kit 12"/300 mm pole * 15-40147Flex Waveguide WR137, 36" 15-40189Kit, Conv Mounting, HP SSPAs Incl in HP transceiver system 15-40196-000Kit, Connector Sealing Incl in transceiver system 15-40202RF Monitor Port option, 10 W and 20 W SSPAs 15-41000-000Kit, Boom Mounting Incl in LP transceiver system 15-42000-000Kit, Wg-WG Mtg CPR137G CE SSPA Hub Mtg Incl in HP transceiver system 15-42030-000Kit, SSPA Hub Mounting Incl in HP transceiver system 15-42031-000Manual, C-Band Transceiver reference Incl in transceiver system 15-44001-ENHand-held Controller 5560 5560Remote Controller package 5570, 100m cable * 5570-100Remote Controller package 5570, 50m cable 5570-50Hex Driver, 2.5 x 75 with handle Incl in transceiver system 75-31400-002TRF, 3.625—4,200 GHz c/w flange kit TRF-C2 *


C-BAND TRANSCEIVERS MODULE PACKAGES ORDERING GUIDE

The following list of product packages should only be used to order modules for replacement or upgrade purposes. To order complete transceivers, please use the transceiver ordering codes shown on pages 22 and 23.

Non-core products

Ordering Code Description5700-2/N/S Converter, 5700, Band 2, narrow band, single synthesiser5700-2/N/D Converter, 5700, Band 2, narrow band, dual synthesiser5700-2/W/D Converter, 5700, Band 2, wide band, dual synthesiser5710-2/N-CE SSPA, 5710, 10 W Band 2, N output, CE5710-2/W-CE SSPA, 5710, 10 W Band 2, waveguide output, CE5720-2/N-CE SSPA, 5720, 20 W Band 2, N output, CE5720-2/W-CE SSPA, 5720, 20 W Band 2, waveguide output, CE5740-2/N-CE SSPA, 5740, 40 W Band 2, N output , CE5740-2/W-CE SSPA, 5740, 40 W Band 2, waveguide output, CE5760-2/W-CE SSPA, 5760, 60 W Band 2, waveguide output, CE5760-2/W SSPA, 5760, 60 W Band 2, waveguide output5712H-2/W-CE SSPA, 5712H, 120 W Band 2, waveguide output, CE5712H-2/W SSPA, 5712H, 120 W Band 2, waveguide outputLNA-2 LNA, Band 2, 40 K (SPC or equivalent)ACC-C-LP Accessory Package, Low power C-Band transceiver (10 W to 40 W)ACC-C-HP Accessory Package, High power C-Band transceiver (60 & 120 W)5582B-8 Mains Power Supply 5582B c/w 8” (200 mm) pole mounting kit5582B-12 Mains Power Supply 5582B c/w 12” (300 mm) pole mounting kit * *


Ku-BAND TRANSCEIVERS MODEL NUMBERING The Ku-Band transceiver ordering code system is designed to provide unambiguous identification of transceiver variants and options. The Ku-Band transceiver options and variants include: SSPA RF output power: 8 W, 16 W or 40 W

RF Frequency Band: Band 1 (Tx, Standard): 14,00—14,50 GHz or

Band 2 (Tx, Extended): 13,75—14,50 GHz Band R1 (Rx): 10,95—11,70 GHz or Band R2 (Rx): 11,70—12,20 GHz or Band R3 (Rx): 12,25—12,75 GHz Converter IF bandwidth: Narrow (40 MHz) or Wide (80 MHz)

Power supply: 48 VDC nominal or AC mains

The ordering code format is shown below and comprises the base order code plus groups of option letters to show the particular transceiver configuration and options fitted. The Ku-Band ordering code comprises an initial group of digits which specify the basic transceiver model and the SSPA RF output power rating, a second group which specifies the Converter options, a third group which specifies the receive band (i.e. LNB option) and a fourth group which specifies the power supply option. Finally, a fifth character group is appended to indicate CE certification. Not all possible combinations of transceiver options are available. To assist with ordering, the transceiver versions that are available are shown in the tables on pages 30 and.31.

59PP–X/Y–AA–BB–GG Model Extension Variant


CE certification: - CE for CE certified version - Blank for non-certified version Operating voltage: - 48 for 48 VDC powered - AC for AC mains powered Receive (LNB) band: - R1 for Band R1: 10,95—11,70 GHz - R2 for Band R2: 11,70—12,20 GHz - R3 for Band R3: 12,25—12,75 GHz Converter bandwidth: - N for Narrow bandwidth (40 MHz) - W for Wide bandwidth (80 MHz) Transmit frequency band: - 1 for Band 1 (Standard): 14,00—14,50 GHz - 2 for Band 2 (Extended): 13,75—14,50 GHz RF output power: - two digits representing RF output power rating (e.g. 16 for 16 W) Note: Where any of the model extension variants “X/Y-AA-BB-GG” have been made BOLD indicates that variant has an option.

Ku-BAND TRANSCEIVERS AC MAINS POWERED

Non-core products

RF output power

Ordering Code

8 W 5908-1/N-R1-AC-CE16 W 5916-1/N-R1-AC-CE

Standardfeatures

Standardaccessories (08-05597-020 & 08-05887-020)

LNBoptions

Converteroptions

Transceiver

options and

accessories(08-05597-030 & 08-05857-030) 3 m *

(08-05366-050) 5 m

(08-05366-080) 8 m

(Pass: 10,7—12,75 GHz, Reject: 13,75—14,25 GHz)

Remote Controller 5570 c/w 100 m cable (5570-100)

LNB to Converter receive RF coax cable length:

Transmit Reject Filter c/w flange kit (TRF-Ku)


Band 2 transmit operation (13,75—14,5 GHz, no CE certification)

AC Power Supply pole mtg kit to suit 300 mm (12") pole * (15-40147)

SSPA to Converter RF & power/control cables length:


Wide IF bandwidth (80 MHz) option


Band R2 operation (11,7—12,2 GHz) (LNB-Ku-R2) Band R3 operation (12,25—12,75 GHz) (LNB-Ku-R3)

AC power cable, 10 m (08-05862-010) Power supply pole mounting kit to suit 200 mm (8") pole) (15-40128) Hex Driver for Converter control panel screws (75-31400-002) Ku-Band transceiver reference manual (15-44005-EN)

LNB to Converter receive RF coax cable, 3 m (08-05366-030) WR75 flange kit for LNB (included with LNB) PC to Converter serial cable, 2 m (08-05301-002)

SSPA to Converter RF and power/control cables, 2 m

SSPA and Converter boom mounting kits (15-42000-000) WR75 flange kit and Allen key for SSPA (15-40173 & 75-30504-107)

Power Supply to Converter DC cable, 5 m (08-05634-005)


Band 1 transmit (14,0—14,5 GHz) LNB Band R1 (10,95—11,70 GHz), 75K typical (LNB-Ku-R1) Narrow IF bandwidth (40 MHz) AC Power Supply (115/230 VAC) (5582B-8) CE certification

WR75 adaptor (M4 to 6-32) c/w flange kit and Allen key (15-40183)

*


Ku-BAND TRANSCEIVERS 48 VDC POWERED

Non-core products


8 W 5908-1/N-R1-48-CE16 W 5916-1/N-R1-48-CE

Standardfeatures

Standardaccessories

LNBoptions

Converteroptions

Transceiver

options andaccessories

(08-05366-050) 5 m * Add(08-05366-080) 8 m * Add

(Pass: 10,7—12,75 GHz, Reject: 13,75—14,25 GHz) Hand-held Controller 5560 (5560) Remote Controller 5570 c/w 50 m cable (5570-50) Remote Controller 5570 c/w 100 m cable (5570-100)

(08-05597-030 & 08-05857-030) 3 m * Add

RF output flexible waveguide, 900 mm (36") length (15-40163) LNB to Converter receive RF coax cable length:

Transmit Reject Filter c/w flange kit (TRF-Ku)


Band 2 transmit operation (13,75—14,5 GHz, no CE certification) Add

SSPA to Converter RF & power/control cables length:


Power Supply to Converter DC cable, 5 m (08-05634-005) Hex Driver for Converter control panel screws (75-31400-002) Ku-Band transceiver reference manual (15-44005-EN) Connector sealing kit c/w self amalgamating tape (15-40202)

WR75 adaptor (M4 to 6-32) c/w flange kit and Allen key (15-40183) LNB to Converter receive RF coax cable, 3 m (08-05366-030) WR75 flange kit for LNB (included with LNB)

SSPA to Converter RF and power/control cables, 2 m (08-05597-020 & 08-05887-020)

SSPA and Converter boom mounting kits (15-42000-000)

PC to Converter serial cable, 2 m (08-05301-002)


Band 1 transmit (14,0—14,5 GHz) LNB Band R1 (10,95—11,70 GHz), 75K typical (LNB-Ku-R1) Narrow IF bandwidth (40 MHz) 48 VDC power CE certification

WR75 flange kit and Allen key for SSPA (15-40173 & 75-30504-107)

*


Ku-BAND TRANSCEIVERS HIGH POWER

Non-core products


40 W 5940-1/N-R1-AC-CE

Standardfeatures

Standardaccessories

LNBoptions

Converteroptions

Transceiver

options andaccessories

(08-05366-050) 5 m * Add(08-05366-080) 8 m * Add

Remote Controller 5570 c/w 100 m cable (5570-100)

Transmit Reject Filter c/w flange kit (TRF-Ku)(Pass: 10,7—12,75 GHz, Reject: 13,75—14,25 GHz)


SSPA to Converter RF & power/control cables length: (08-05597-030 & 08-05857-030) 3 m * Add

RF output flexible waveguide, 900 mm (36") length (15-40163) LNB to Converter receive RF coax cable length:


Band 2 transmit operation (13,75—14,5 GHz) (no CE certification) Add


Ku-Band transceiver reference manual (15-44005-EN) High power SSPA reference manual (15-44011-EN) SSPA Manager software (incl with HP SSPA reference manual) Connector sealing kit c/w self amalgamating tape (15-40202)

PC to Converter serial cable, 2 m (08-05301-002) Converter mounting kit (15-40196-000) SSPA to Converter DC cable, 2 m (08-05857-020) Hex Driver for Converter control panel screws (75-31400-002)

WR75 flange kit and Allen key for SSPA (15-42029-000) WR75 adaptor (M4 to 6-32) c/w flange kit and Allen key (15-40183)

LNB to Converter receive RF coax cable, 3 m (08-05366-030)

SSPA to Converter RF and control cables, 2 m (08-05597-020 & 08-05857-020)

SSPA pole mounting kit (15-42031-000)

WR75 flange kit for LNB (included with LNB)


Band 1 transmit (14,0—14,5 GHz) LNB Band R1 (10,95—11,70 GHz), 75K typical (LNB-Ku-R1) Narrow IF bandwidth (40 MHz) AC Power Supply (104—274 VAC) CE certification

SSPA AC power cable, 5 m (08-06201-005)

*


Ku-BAND TRANSCEIVERS AC POWERED ORDERING GUIDE

Ban

d 1:

14,

00—

14,5

0 G

Hz

Ban

d 2:

13,

75—

14,5

0 G

Hz

Ban

d R

1: 1

0,95

—11

,70

GH

z

Ban

d R

2: 1

1,70

—12

,20

GH

z

Ban

d R

3: 1

2,25

—12

,75

GH

z

5908-1/N-R1-AC-CE 8 * * N Y5908-1/W-R1-AC-CE 8 * * W Y5908-1/N-R2-AC-CE 8 * * N Y5908-1/W-R2-AC-CE 8 * * W Y5908-1/N-R3-AC-CE 8 * * N Y5908-1/W-R3-AC-CE 8 * * W Y5908-2/N-R1-AC 8 * * N N5908-2/W-R1-AC 8 * * W N5908-2/N-R2-AC 8 * * N N5908-2/W-R2-AC 8 * * W N5908-2/N-R3-AC 8 * * N N5908-2/W-R3-AC 8 * * W N5916-1/N-R1-AC-CE 16 * * N Y5916-1/W-R1-AC-CE 16 * * W Y5916-1/N-R2-AC-CE 16 * * N Y5916-1/W-R2-AC-CE 16 * * W Y5916-1/N-R3-AC-CE 16 * * N Y5916-1/W-R3-AC-CE 16 * * W Y5916-2/N-R1-AC 16 * * N N5916-2/W-R1-AC 16 * * W N5916-2/N-R2-AC 16 * * N N5916-2/W-R2-AC 16 * * W N5916-2/N-R3-AC 16 * * N N5916-2/W-R3-AC 16 * * W N5940-1/N-R1-AC-CE 40 * * N Y5940-1/W-R1-AC-CE 40 * * W Y5940-1/N-R2-AC-CE 40 * * N Y5940-1/W-R2-AC-CE 40 * * W Y5940-1/N-R3-AC-CE 40 * * N Y5940-1/W-R3-AC-CE 40 * * W Y5940-2/N-R1-AC 40 * * N N5940-2/W-R1-AC 40 * * W N5940-2/N-R2-AC 40 * * N N5940-2/W-R2-AC 40 * * W N5940-2/N-R3-AC 40 * * N N5940-2/W-R3-AC 40 * * W N

IF B

andw

idth

(Nar

row

: 40

MH

z,

Wid

e: 8

0 M

Hz)

CE

Cer

tific

atio

n

Model Number Out

put P

ower

(W)

Transmit Band Receive Band


Ku-BAND TRANSCEIVERS 48 VDC POWERED ORDERING GUIDE

Ban

d 1:

14,

00—

14,5

0 G

Hz

Ban

d 2:

13,

75—

14,5

0 G

Hz

Ban

d R

1: 1

0,95

—11

,70

GH

z

Ban

d R

2: 1

1,70

—12

,20

GH

z

Ban

d R

3: 1

2,25

—12

,75

GH

z

5908-1/N-R1-48-CE 8 * * N Y5908-1/W-R1-48-CE 8 * * W Y5908-1/N-R2-48-CE 8 * * N Y5908-1/W-R2-48-CE 8 * * W Y5908-1/N-R3-48-CE 8 * * N Y5908-1/W-R3-48-CE 8 * * W Y5908-2/N-R1-48 8 * * N N5908-2/W-R1-48 8 * * W N5908-2/N-R2-48 8 * * N N5908-2/W-R2-48 8 * * W N5908-2/N-R3-48 8 * * N N5908-2/W-R3-48 8 * * W N5916-1/N-R1-48-CE 16 * * N Y5916-1/W-R1-48-CE 16 * * W Y5916-1/N-R2-48-CE 16 * * N Y5916-1/W-R2-48-CE 16 * * W Y5916-1/N-R3-48-CE 16 * * N Y5916-1/W-R3-48-CE 16 * * W Y5916-2/N-R1-48 16 * * N N5916-2/W-R1-48 16 * * W N5916-2/N-R2-48 16 * * N N5916-2/W-R2-48 16 * * W N5916-2/N-R3-48 16 * * N N5916-2/W-R3-48 16 * * W N

IF B

andw

idth

(Nar

row

: 40

MH

z, W

ide:

80

MH

z)

CE

Cer

tific

atio

n

Model Number Out

put P

ower

(W)

Transmit Band Receive Band


Ku-BAND TRANSCEIVERS ACCESSORIES ORDERING GUIDE

Non-core products

Description Comment


Cable, Serial Conv-PC, (DB-9S) 2 m Incl in transceiver system 08-05301-002Cable, Coax 50 Ohm N-N Plug 2 m 08-05366-020Cable, Coax 50 Ohm N-N Plug 3 m 08-05366-030Cable, Coax 50 Ohm N-N Plug 5 m 08-05366-050Cable, Coax 50 Ohm N-N Plug 8 m 08-05366-080Cable, Heliax N-N 10-15GHz 2 m Incl in transceiver system 08-05597-020Cable, Heliax N-N 10-15GHz 3 m * 08-05597-030Cable, Heliax N-N 10-15GHz 4 m * 08-05597-040Cable, DC Power (Rd/Bk) 5 m Incl in LP transceiver system 08-05634-005Cable, HP SSPA to Converter 2,0 m Incl in transceiver system 08-05857-020Cable, HP SSPA to Converter 3,0 m * 08-05857-030Cable, HP SSPA to Converter 4,0 m * 08-05857-040Cable, AC 3 core 24/0, 20 8 m Incl in LP AC transceiver system 08-05862-010Cable, Converter to SSPA Connector 2 m Incl in transceiver system 08-05887-020Cable, Converter to SSPA Connector 3 m * 08-05887-030Cable, Converter to SSPA Connector 4 m * 08-05887-040Cable, DC Pwr SSPA - Converter 2 m Incl in HP transceiver system 08-05961-002Cable, DC Pwr SSPA - Converter 3 m * 08-05961-003Cable, DC Pwr SSPA - Converter 4 m * 08-05961-004Cable, AC Mains 5 m Incl in HP transceiver system 08-06201-005Power Supply Pole Mount Kit 8"/200 mm pole Incl in LP AC transceiver system 15-40128Power Supply Pole Mount Kit 12"/300 mm pole * 15-40147Flex Waveguide WR75, 36" 15-40163Flange Kit, WR75, Thin Groove Incl in LP transceiver system 15-40173Kit, WR75 W/G Adaptor Incl in transceiver system 15-40183Kit, Conv Mounting, HP SSPAs Incl in HP transceiver system 15-40196-000Kit, Connector Sealing Incl in transceiver system 15-40202Kit, Boom Mounting Incl in LP transceiver system 15-42000-000Kit, Wg-WG Mtg PBR120 Ku-Band SSPA Incl in HP transceiver system 15-42029-000Kit, SSPA Hub Mounting Incl in HP transceiver system 15-42031-000Manual, Ku-Band Transceiver Reference Incl in transceiver system 15-44005-ENHand-held Controller 5560 5560Remote Controller package 5570, 100m cable * 5570-100Remote Controller package 5570, 50m cable 5570-50Hex Driver, 3mm (M4) Incl in LP transceiver system 75-30504-107Hex Driver, 2.5 x 75 with handle Incl in transceiver system 75-31400-002TRF, 13,75—14,50GHz c/w flange kit TRF-Ku *


Ku-BAND TRANSCEIVERS MODULE PACKAGES ORDERING GUIDE

The following list of product packages should only be used to order modules for replacement or upgrade purposes. To order complete transceivers, please use the transceiver ordering codes shown on pages 30 and.31.

Non-core products

Ordering Code Description5900-1/N Converter, 5900, Band 1, narrow band5900-1/W Converter, 5900, Band 1, wide band5900-2/N Converter, 5900, Band 2, narrow band5900-2/W Converter, 5900, Band 2, wide band5908-1-CE SSPA, 5908, 8 W, Band 1, CE5908-2 SSPA, 5908, 8 W, Band 25916-1-CE SSPA, 5916, 16 W, Band 1, CE5916-2 SSPA, 5916, 16 W, Band 25940-1-CE SSPA, 5940, 40 W, Band 1, CE5940-2 SSPA, 5940, 40 W, Band 2LNB-TR-R1 LNB, Band R1, 75KLNB-TR-R2 LNB, Band R2, 75KLNB-TR-R3 LNB, Band R3, 75KACC-Ku-LP Accessory Package, Low power Ku-Band transceiver (4 W to 16 W)ACC-Ku-HP Accessory Package, High power Ku-Band transceiver (40 W)5582B-8 Mains Power Supply 5582B c/w 8” (200 mm) pole mounting kit5582B-12 Mains Power Supply 5582B c/w 12” (300 mm) pole mounting kit * *


TRANSCEIVER REDUNDANCY SWITCHING SYSTEMS MODEL NUMBERING The transceiver redundancy switching systems ordering code format is designed to provide unambiguous identification of the various redundancy systems available. The system configuration required depends on the particular transceiver and options as follows: RF Frequency band: C-Band or Ku-Band

SSPA RF output connector: N-type coaxial (C-Band only) or Waveguide (C-Band and Ku-Band)

RF output power: Segregated by SSPA mechanical differences

(medium or high power) The transceiver redundancy system model number format is shown below. The model number comprises the base model number plus groups of option letters/numbers to specify the particular configuration. The first group of characters specifies the fundamental frequency band of the system and the second group specifies the SSPA RF output connector option. The last group specifies the transceiver power range as the medium and high power systems have SSPA mechanical differences.

5586–AA/B–CC Model Extension Variant


Transceiver power range: - M for Medium: C-Band: 10 W to 40W Ku-Band: 8 W & 16 W - H for High: C-Band: 60 W & 120 W Ku-Band: 40 W Transceiver SSPA output connector: - N for N-type coaxial (C-Band only) - W for Waveguide (C-band and Ku-Band) Frequency band: - C for C-Band - Ku for Ku-Band

TRANSCEIVER REDUNDANCY SWITCHING SYSTEMS


Single switch configuration for use with 10 W to 40 W transceivers, N-type output SSPAs

5586-C/N-M

Dual switch configuration for use with 10 W to 40 W transceivers, waveguide output SSPAs

5586-C/W-M

Dual switch configuration for use with 60 W and 120 W transceivers, waveguide output SSPAs

5586-C/W-H

Ku-Band systems

Dual switch configuration for use with 8 W, and 16 W transceivers

5586-Ku/W-M

Dual switch configuration for use with 40 W transceivers

5586-Ku/W-H

Standardaccessories

Redundancy systems

Redundant System Monitor 5587 c/w 50 m cable

5587-50


Redundant System Monitor 5587 c/w 100 m cable

5587-100

Dual Remote Controller 5570D (c/w cables) 5570D

(C-Band 78-18005-004 OR 78-18005-002 & 78-18005-003; Ku-Band 78-18008)

Redundancy Controller pole mounting kit (15-40128) Redundancy Controller to Converter IF coax cables (08-05366-050) Redundancy Controller to Converter control cables (08-05160-005) Waveguide switch(es)

Redundancy Controller 5586 (08-05695-001) Redundancy Controller power cables (60-60202-801 per m)

Waveguide switch control cable(s) (08-05158-00x & 08-05159-00x) Waveguide hardware to suit

(flange kits, waveguide bends, spacers and blanking plate) Off-line SSPA high power termination

(C-Band 78-23015/ 78-23027; Ku-Band 78-23020/ 78-23021)

Converter and SSPA dual boom mounting kits User manual (15-44003-EN) Connector sealing kit c/w self-amalgamating tape (15-40202)


TRANSCEIVER REDUNDANCY SWITCHING SYSTEMS ORDERING GUIDE

Description Comment


Cable, 6-way Rx Waveguide Switch 5m Incl in all systems 08-05158-005Cable, 6-way Tx Waveguide Switch 5m Incl in C-Band W/G and Ku-Band sys 08-05159-005Cable 19-way MIL-conn (P) to (S) 5m Incl in all systems 08-05160-005Cable, Coax 50 Ohm N-N Plug 1 m Incl in N-type and HP C-Band sys 08-05366-010Cable, Coax 50 Ohm N-N Plug 2 m 08-05366-020Cable, Coax 50 Ohm N-N Plug 3 m 08-05366-030Cable, Coax 50 Ohm N-N Plug 5 m Incl in all systems 08-05366-050Cable, Coax 50 Ohm N-N Plug 8 m 08-05366-080Cable, Aux Power HP Redundancy Incl in all HP systems 08-05641-001

Flange Kit WR137 Full Thickness Gasket c/w nuts Incl in HP C-Band systems 15-40096Flange Kit WR229 Full Thickness Gasket c/w 16mm screws Incl in C-Band systems 15-40106Flange Kit WR229 Half Thickness Gasket c/w 12mm screws Incl in C-Band systems 15-40107Flange Kit WR229 Half Thickness Gasket c/w 8mm screws Incl in C-Band systems 15-40108Flange Kit WR137 Half Thickness Gasket c/w 12mm screws Incl in C-Band W/G systems 15-40123Red Controller Pole Mount Kit 8"/200 mm pole Incl in all systems 15-40128Flange Kit, WR75, Thick Groove Incl in Ku-Band systems 15-40172Flange Kit, WR75, Thin Groove Incl in Ku-Band systems 15-40173Flange Kit, WR75, Universal Incl in Ku-Band systems 15-40174Kit, Conv Mounting, HP SSPAs Incl in HP systems 15-40196-000Kit, Connector Sealing Incl in all systems 15-40202

Kit, Mounting Redundant ConvertersMounting Redundant Converters when used with 3rd Party SSPAs 15-42069-000

Manual, C-Band Transceiver Switching Eq Included in C-Band systems 15-44003-ENManual, Ku-Band Transceiver Switching Eq Included in Ku-Band systems 15-44007-ENAdaptor, N 90 degree male-female Incl in C-Band N-type systems 60-15863-945Cable, 2-core screened, 7/0, 50 (10 m) 10m Incl with std systems 67-60202-801Adaptor WR137 Waveguide to N Type Incl in C-Band LP W/G systems 78-01001-005Attenuator, 30dB, 50W N DC to 8.5 GHz Incl in C-Band LP systems 78-01101Waveguide Switch, WR137 (C-Band Tx) Incl in C-band W/G-type systems 78-18005-002Waveguide Switch, WR229 (C-Band Rx) Incl in C-band W/G-type systems 78-18005-003Waveguide Switch, Dual WR229/ N-type (C-Band Tx/ Rx) Incl in C-band N-type systems 78-18005-004Waveguide Switch, WR75 (Ku-Band Tx or Rx) Incl in Ku-Band systems 78-18008Waveguide Bend 90d WR137 3” x 3” Incl in C-Band W/G systems 78-23011-001Waveguide, Rigid WR137 3” Incl in HP C-Band systems 78-23012Waveguide, Jacket Flextwist WR137 12” Incl in HP C-Band systems 78-23014Waveguide termination 125W WR137 Incl in LP C-Band systems 78-23015Waveguide, Rigid WR75 2” Incl in Ku-Band systems 78-23018Waveguide, Bend 90 deg WR75 3.2” x 2” Incl in Ku-Band systems 78-23019Waveguide termination 25W WR75 Incl in LP Ku-Band systems 78-23020Waveguide termination 75W WR75 Incl in HP Ku-Band systems 78-23021Waveguide termination 300W WR137 Incl in HP C-Band systems 78-23027Waveguide, Jacket extra Flextwist WR75 2.5” Incl in LP Ku-Band systems 78-23028Waveguide, Jacket Flextwist WR75 18” Incl in HP Ku-Band systems 78-23029


TRADING TERMS (INTERNATIONAL SALES)


Prices Prices are quoted in US Dollars, UK Pounds Sterling, Euros and Australian Dollars.

When specifically required, quotations in other major international currencies can be

provided upon request. Terms of Payment Codan Limited means Codan Limited ABN 77 007 590 605, 81 Graves Street Newton, South Australia, 5074. Codan Limited offers a range of payment terms. Dealers/Customers can arrange to have pre-approved credit facilities with Codan. Please note that the value of any outstanding orders combined with any outstanding payments due to Codan by the Dealer/Customer must fall within the approved credit limit. Alternately, if the Dealer/Customer does not have a pre-approved credit facility with Codan, the Dealer/Customer must pay for the order at the time of placing the order. Payment must be made by the Dealer/Customer by way of either: Irrevocable Documentary Credit (see conditions on page 39)

Or

Telegraphic Transfer.

Please note that ownership of the goods will pass to the Dealer/Customer only when Codan Limited has received full payment of the Purchase Price.

TRADING TERMS (INTERNATIONAL SALES)


Method of Despatch AIRFREIGHT unless otherwise instructed at time of order. Shipping Terms & Point of Delivery Codan Limited complies with INCOTERMS 2000 – ICC Publication No. 560. Codan has an In-House Freight Forwarder who can deliver product to all main airports throughout the world, and we would be happy to provide a freight quote for your orders. If you choose to use your own Freight Forwarder, please provide full contact details of their Australian Agent so that Codan Limited can liaise to have your goods collected in a prompt and efficient manner. Risk in the goods will pass to the Dealer/Customer upon collection of the goods by the Dealer/ Customer or by any carrier commissioned by the Dealer/Customer, or upon delivery to the Dealer/Customer by any other means. Once Risk has passed to the Dealer/Customer, it is the Dealer/Customer’s responsibility to insure the goods. The nearest International Airport to our premises is in Adelaide, South Australia however we also use Melbourne and Sydney airports for despatch of goods. Quotations can be provided for any of the following: Ex Works Newton, South Australia CPT (Carriage Paid To … (named airport of arrival)) CIP (Carriage and Insurance Paid to ... (named airport of arrival))

Packing Our export packing is designed to International Export Standards to ensure safe delivery under normal international airfreight handling conditions. Special packaging requirements (labelling, banding, waterproofing, crating, etc.) can be arranged at additional cost.

CONDITIONS FOR IRREVOCABLE DOCUMENTARY LETTER OF CREDIT


Beneficiary: Codan Limited 81 Graves Street Newton, South Australia, 5074 Beneficiaries Bankers: Australia and New Zealand Banking Group Limited, Adelaide (Swift: ANZBAU5A), or HSBC Bank Australia Limited, Adelaide (Swift: HKBAAU2S), or your Main Australian Correspondent Bank in South Australia Please Establish By: Swift/Telex Expiry Date: 8 weeks from establishment of LC Place of Expiry: Australia Confirmation: Confirmation allowed Confirmation charges are for the account of Beneficiary Available With/By: Freely negotiable with any Australian Bank Payment Terms: Irrevocable Confirmed Letter of Credit 100% payable at Sight upon presentation of shipping documents Partial Shipments: Allowed Transhipment: Allowed Despatch From: Any Australian Airport For Transportation To: (Insert Destination Airport) Latest Shipment: 5 weeks from establishment of LC Documents Required: - Commercial Invoices - Packing Lists - Air Waybill marked "Freight Prepaid/Collect" as per ProForma

Invoice - Certificate of Origin (if required) - Insurance Certificate (if required) Shipping Terms: Incoterms (2000) as per ProForma Invoice Additional Conditions: Documents to be presented within 21 days from date of issuance

of Air Waybill. Charges: All other Bank charges outside the applicant’s country are for the

account of the Beneficiary, excluding establishing Bank charges.

INTERNATIONAL PRODUCT WARRANTY


Codan Limited ('Codan') warrants that all equipment manufactured by Codan will be free of faults arising from defects in design, workmanship or materials in accordance with this express warranty. Should any fault due to bad design, workmanship or materials be proven at any time within the prescribed warranty period, Codan will, subject to the terms of this warranty as set out below, remedy such fault free of charge provided the equipment is returned, carriage paid, to Codan or to a service centre authorised by Codan. The prescribed warranty period for equipment manufactured by Codan is three (3) years after shipment from the factory. In addition, where Codan (or a service centre authorised by Codan) repairs equipment or supplies spare parts, the prescribed warranty period for the repaired equipment or spare parts is three (3) months after shipment to the customer. This express warranty shall not extend to any abuse, accident or improper installation, connection, adjustment or use of goods otherwise than in accordance with instructions issued by Codan. Subject to the matters set out in this express warranty, no liability expressed or implied, is accepted for any consequential loss, damage or injury arising as a result of any fault in the goods. This express warranty does not extend to goods supplied by Codan, which are not designed or manufactured by it. Codan will, however, make reasonable endeavours to ensure that the purchaser receives the full benefit of any warranty given by the manufacturer. This express warranty is valid for goods purchased from Codan anywhere in the world. Warranty service will be provided in accordance with this express warranty in any country of the world where there is a service centre authorised by Codan. The benefits conferred by this express warranty are in addition to all other non-excludable rights and remedies which the consumer may have under the Australian Trade Practices Act and any similar laws in Australia or elsewhere. To the extent permitted by law, Codan’s liability for any non-excludable condition or warranty is limited to (at Codan’s option): (a) In the case of goods - repairing, replacing or supplying equivalent goods, or paying the cost of any of those remedies; or (b) In the case of services - supplying the services again or paying the cost of having the services supplied again.

Codan Limited International Product Warranty - April, 2002