· Web viewWindows: Provide door sections with windows in lieu of 0.050 inch (1.3mm) aluminum filler panels. Locations to comply with door elevation drawings. ** NOTE TO SPECIFIER

SECTION 08 36 16 (08 36 16)SECTIONAL OVERHEAD DOORS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2006 - 2019 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Commercial sectional doors.

1.2 RELATED SECTIONS

1.2.1 Section 05 50 00 - Metal Fabrications.

1.2.2 Section 08 71 53 - Security Door Hardware.

1.2.3 Section 09 90 00 - Painting and Coating.

1.2.4 Section 11 12 26.13 - Parking Fee Coin Collection Equipment.

1.2.5 Section 26 05 00 - Common Work Results for Electrical.

1.3 REFERENCES

1.3.1 ASTM International (ASTM):1.3.1.1 ASTM A 653/A 653M - Standard Specification for Steel Sheet, Zinc-Coated

(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process.1.3.1.2 ASTM C 518 - Standard Test Method for Steady-State Thermal Transmission

Properties by Means of the Heat Flow Meter Apparatus.1.3.1.3 ASTM E 283 - Standard Test Method for Determining the Rate of Air Leakage

Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.4.2.1 Preparation instructions and recommendations.1.4.2.2 Storage and handling requirements and recommendations.1.4.2.3 Installation methods.

1.4.3 Performance Standards: Provide test data validating the following:1.4.3.1 Door Section: Gloss retention, fade resistance, FDA compliance, cold crack

performance, load to rebound, dent resistance impact.1.4.3.2 Drive Train: Spring cycle life, track, hinges, rollers, cable assembly, cable

strength.1.4.3.3 Door Assembly: Thermal performance, deflection, wind load.

1.4.4 Shop Drawings:

08 36 16 -1

1.4.4.1 Provide drawings indicating track details, head and jamb conditions, spring shafts, anchorage, accessories, finish colors, patterns and textures, operator mounts and other related information.

1.4.4.2 Regulatory Requirements and Approvals: Provide shop drawings in compliance with local Authority having Jurisdiction (AHJ).

1.4.5 Certifications:1.4.5.1 Submit manufacturer's certificate that products meet or exceed specified

requirements.1.4.5.2 Submit installer qualifications.

1.4.6 Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

1.4.7 Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

1.5 QUALITY ASSURANCE

1.5.1 Installer Qualifications: Utilize an installer having demonstrated experience on projects of similar size and complexity, and trained and authorized by the door manufacturer to perform the work of this section.

1.6 DELIVERY, STORAGE, AND HANDLING

1.6.1 Store products in manufacturer's unopened packaging until ready for installation.

1.7 PROJECT CONDITIONS

1.7.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.8 WARRANTY

1.8.1 Provide manufacturer's standard warranty against defects in material and workmanship, as further described with each model in Part 2 of this Section.

1.8.2 Manufacturer's Warranty for ControlHoist Commercial Operators: Provide manufacturer's standard warranty.1.8.2.1 Raynor warrants the electrical operator and component parts for two (2) years

against defects in material and workmanship when purchased as operator only.

1.8.3 Manufacturer's Warranty for ControlHoist Commercial Operators Door and Operator Warranty Package: Provide manufacturer's standard warranty.1.8.3.1 Raynor warrants the electrical operator and component parts against defects in

material and workmanship for three (3) years, on the operator only, when purchased with any model of Raynor commercial sectional door.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Raynor, which is located at: 1101 East River Rd. P. O. Box 448; Dixon, IL 61021-0448; Toll Free Tel: 800-4-RAYNOR; Tel: 815-288-1431; Fax: 888-598-4790; Email:request info ([email protected]); Web:http://www.raynor.com

2.1.2 Substitutions: Not permitted.

08 36 16 -2

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 SECTIONAL THERMAL SANDWICH DOOR (POLYSTYRENE OR POLYURETHANE INSULATION)

2.2.1 TC Series as manufactured by Raynor Garage Doors:2.2.1.1 Doors:

2.2.1.1.1 Operation:2.2.1.1.1.1 Provide doors designed for manual operation.2.2.1.1.1.2 Provide doors designed for hand chain operation.2.2.1.1.1.3 Provide doors designed for electric motor operation.

2.2.1.1.2 Jamb Construction:2.2.1.1.2.1 Steel jambs with self-tapping fasteners.2.2.1.1.2.2 Wood jambs with lag screw fasteners.2.2.1.1.2.3 Masonry jambs with anchor bolt fasteners.

2.2.1.1.3 Structural Performance Requirements:2.2.1.1.3.1 Wind Loads: Uniform pressure of: ________ psf.

2.2.1.2 Sections:2.2.1.2.1 TC200:

2.2.1.2.1.1 Sections shall be pressure bonded to a 1-7/8 inches (48 mm) thick expanded polystyrene core with interior and exterior skins separated by a continuous thermal break. Hinge reinforcement plates shall be 16 gauge edge plates and 16 gauge center plates, located within section interior at every hinge location. End stiles to be 18 gauge galvanized steel.

2.2.1.2.1.2 Material: Steel sandwich construction, 2 inches (50.8 mm) thick, roll formed from draw quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior and interior skin to be constructed of 26 gauge steel embossed stucco texture.

2.2.1.2.1.3 Finish: Exterior skin to have two coats of paint, one primer coat and one finish coat.

2.2.1.2.1.3.1 Color: White polyester paint.2.2.1.2.1.3.2 Color: Almond polyester paint.2.2.1.2.1.3.3 Color: BronzeTone polyester paint.2.2.1.2.1.3.4 Color: ClayTone polyester paint.2.2.1.2.1.3.5 Color: Dark Brown Kynar paint.2.2.1.2.1.3.6 Color: Frost White Kynar paint.2.2.1.2.1.3.7 Color: Beige Kynar paint.2.2.1.2.1.3.8 Color: Sepia Brown Kynar paint.2.2.1.2.1.3.9 Color: Desert Tan polyester paint.2.2.1.2.1.3.10 ArmorBrite Powdercoat finish, color as selected by

Architect.2.2.1.2.1.3.11 Color: ________.2.2.1.2.1.3.12 Color: As detailed on the Drawings.2.2.1.2.1.3.13 Color: As determined by Architect from Raynor's

ColorWave post paint process featuring 1500 colors of Sherwin Williams Polane Enamel paint.

2.2.1.2.1.4 Insulation: Expanded polystyrene with R-value of 10.25.2.2.1.2.2 TC224:

2.2.1.2.2.1 Sections shall be pressure bonded to a 1-7/8 inches (48 mm) thick expanded polystyrene core with interior and exterior skins separated by a continuous thermal break. Hinge reinforcement plates shall be 16 gauge edge plates and 16 gauge center plates, located within section interior at every hinge location. End stiles to be 18 gauge galvanized steel.

08 36 16 -3

2.2.1.2.2.2 Material: Steel sandwich construction, 2 inches (50.8 mm) thick, roll formed from draw quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior skin to be constructed of 24 gauge steel embossed stucco texture and interior skin to be constructed of 26 gauge steel embossed stucco texture.


2.2.1.2.2.3.1 Color: White polyester paint.2.2.1.2.2.3.2 Color: Dark Brown Kynar paint.2.2.1.2.2.3.3 Colorwave Finish: Color as selected by Architect.2.2.1.2.2.3.4 ArmorBrite Powdercoat Finish: Color as selected by

Architect.2.2.1.2.2.4 Insulation: Expanded polystyrene with R-value of 10.25.

2.2.1.2.3 Seals: Bottom of door to have flexible U-shaped vinyl seal retained in aluminum rail.

2.2.1.2.3.1 Provide blade seal on top section to prevent airflow above header.2.2.1.2.4 Trussing: Doors designed to withstand specified windload. Deflection of

door in horizontal position to be maximum of 1/120th of door width.2.2.1.3 Windows: Locations to comply with door elevation drawings.

2.2.1.3.1 24 inches by 8 inches (610 mm by 203 mm) window in a rectangular two-piece black frame.



2.2.1.3.4 Full-view window consisting of aluminum stile and rail construction and color matched to door exterior with powdercoat paint.

2.2.1.3.5 40 inches by 12 inches (1016 mm by 305 mm) full-view (square-edge) window encased in an extruded PVC frame.

2.2.1.3.6 46 inches by 12 inches (1168 mm by 305 mm) full-view (square-edge) window encased in an extruded PVC frame.

2.2.1.4 Glazing: Windows to be provided with insulated glazing units as follows:2.2.1.4.1 Glass consisting of two panes of 1/8 inch (3.2 mm) thick DSB glass.2.2.1.4.2 Glass consisting of two panes of 3/16 inch (4.8 mm) thick glass.2.2.1.4.3 Reinforced glass consisting of one pane of 1/4 inch (6.4 mm) thick wire-

reinforced glass (exterior pane) and one pane of 1/8 inch (3.2 mm) DSB glass (interior pane).

2.2.1.5 Mounting: Sections mounted in door opening using:2.2.1.5.1 Between-Jamb Bracket Mounting: sections mounted between door jambs,

seal against exterior perimeter seal installed along vertical and top horizontal edges of jambs.

2.2.1.5.2 Lap Jamb Angle Mounting: section overlap door jambs by 1 inch (25 mm) on each side of door opening.

2.2.1.6 Track:2.2.1.6.1 Material: Hot-dipped galvanized steel (ASTM A 653), fully adjustable for

adequate sealing of door to jamb or weatherseal.2.2.1.6.2 Configuration Type: Normal Headroom.2.2.1.6.3 Configuration Type: Low Headroom.2.2.1.6.4 Configuration Type: Vertical Lift.2.2.1.6.5 Configuration Type: Lift-Clearance.2.2.1.6.6 Configuration Type: Incline.2.2.1.6.7 Configuration Type: Contour.2.2.1.6.8 Track Size: 2 inches (51 mm).

2.2.1.6.8.1 Jamb Type: Wood only.2.2.1.6.8.1.1 Mounting: Adjustable track brackets.

2.2.1.6.8.2 Jamb Type: Steel, wood, or masonry.

08 36 16 -4

2.2.1.6.8.2.1 Mounting: Floor-to-header angles. Continuous angles from floor to door header. Angle Size: 2-5/16 x 4 x 3/32 inches (59 x 102 x 2.5 mm).

2.2.1.6.8.2.2 Mounting: Floor-to-shaft angles. Continuous angles from floor, past header, up to door shaft. Angle Size: 2-5/16 x 4 x 3/32 inch (59 x 102 x 2.5 mm).

2.2.1.6.8.2.3 Mounting: QuikClip. Clip-Angle brackets pre-assembled to continuous angle from floor to door header and continuous angle from door header to door shaft. Angle Size: 2-5/16 x 1-1/4 x 3/32 inches (59 x 32 x 2.5 mm).

2.2.1.6.9 Track Size: 3 inches (76 mm).2.2.1.6.9.1 Jamb Type: Steel, wood, or masonry.

2.2.1.6.9.1.1 Mounting: Floor-to-header angles. Continuous angles from floor to door header. Angle Size: 3-1/2 x 5 x 3/32 inches (89 x 127 x 2.5 mm) on 3-inch track.

2.2.1.6.9.1.2 Mounting: Floor-to-shaft angles. Continuous angles from floor, past header, up to door shaft. Angle Size: 3-1/2 x 5 x 3/32 inches (89 x 127 x 2.5 mm) on 3-inch track.

2.2.1.6.9.1.3 Mounting: QuikClip. Clip-Angle brackets pre-assembled to continuous angle from floor to door header and continuous angle from door header to door shaft. Angle Size: 3-1/2 x 1-1/4 x 3/32 inches (89 x 32 x 2.5 mm) on 3-inch track.

2.2.1.6.10 Finish:2.2.1.6.10.1 Galvanized.2.2.1.6.10.2 White Powdercoat.

2.2.1.7 Counterbalance:2.2.1.7.1 Counterbalance System: Provided with aircraft-type, galvanized steel lifting

cables with minimum safety factor of 5. Torsion Springs consisting of heavy-duty oil-tempered wire torsion springs on a continuous ball-bearing cross-header shaft.

2.2.1.7.1.1 Spring Cycle Requirements: Standard 10,000 cycles.2.2.1.7.1.2 Spring Cycle Requirements: High cycle: ___________ cycles.

2.2.1.8 Hardware:2.2.1.8.1 Hinges and Brackets: Fabricated from galvanized steel.2.2.1.8.2 Track Rollers: 2 inches (50.8 mm) diameter consistent with track size, with

hardened steel ball bearings.2.2.1.8.3 Track Rollers: 3 inches (76.2 mm) diameter consistent with track size, with

hardened steel ball bearings.2.2.1.8.4 Perimeter Seal: Provide complete weather stripping system to reduce air

infiltration. Weather stripping shall be replaceable.2.2.1.8.4.1 For bracket mounted doors provide climate seal or vinyl seal with

aluminum retainer.2.2.1.8.4.2 For angle mounted doors provide angle clip-on seal.

2.2.1.8.5 Furnish door system with locks: Exterior lock with five-pin tumbler cylinder, night latch and steel bar engaging track.

2.2.1.8.6 Furnish door system with locks: Interior lock with dead bolt provided with hole to receive padlock provided by Owner.

2.2.1.9 TC Limited Warranty: Raynor warrants the door sections against defects in material and workmanship, and deterioration due to rust-through for ten years from date of delivery to the original purchaser. Raynor also warrants the door sections against delamination of the insulation from the steel skins for ten years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional

08 36 16 -5

Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.

2.2.2 ThermaSeal as manufactured by Raynor Garage Doors:2.2.2.1 Doors:




2.2.2.1.4 International Energy Conservation Code (IECC) Requirements:2.2.2.1.4.1 Air Infiltration - Maximum air leakage of 0.4 cfm/ft2 is required.

Testing shall be in accordance with DASMA 105 test procedure.2.2.2.1.4.2 Raynor ThermaSeal TM200 and TM220 provide an air leakage

rating of 0.12 cfm/ft2 with optional IECC Compliance Package.2.2.2.1.4.3 Raynor ThermaSeal TM175 provides an air leakage rating of 0.22

cfm/ft2 with optional IECC Compliance Package.2.2.2.1.4.4 Raynor ThermaSeal TM200 and TM220 provide an installed U-

factor of 0.19.2.2.2.1.4.5 Raynor ThermaSeal TM175 provides an installed U-factor of 0.21.

2.2.2.2 Sections:2.2.2.2.1 ThermaSeal TM320:

2.2.2.2.1.1 Sections shall be pressure bonded to injected polyurethane foam insulated core. Hinge reinforcement strips shall be 20 gauge galvanized steel, located within section interior. End stiles to be 16 gauge galvanized steel.

2.2.2.2.1.2 Material: Steel sandwich construction, 3 inches (76 mm) thick, roll formed from commercial quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior skin shall be constructed of 20 gauge steel with flush, smooth texture and interior skin shall be 26 gauge steel with embossed stucco texture.


2.2.2.2.1.4 Color: White polyester paint.2.2.2.2.1.5 Insulation: Expanded polyurethane with an R-value of 24.54.

2.2.2.2.2 ThermaSeal TM300:2.2.2.2.2.1 Sections shall be pressure bonded to injected polyurethane foam

insulated core. Hinge reinforcement strips shall be 20 gauge galvanized steel, located within section interior. End stiles to be 16 gauge galvanized steel.

2.2.2.2.2.2 Material: Steel sandwich construction, 3 inches (76 mm) thick, roll formed from commercial quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior skin shall be constructed of 26 gauge steel and interior skin shall be 26 gauge steel with embossed stucco texture.


2.2.2.2.2.3.1 Color: White polyester paint.2.2.2.2.2.3.2 Color: PVDF Coated Brown.2.2.2.2.2.3.3 Color: PVDF Coated Sepia.2.2.2.2.2.3.4 Color: PVDF Coated Beige.

08 36 16 -6

2.2.2.2.2.3.5 Color: PVDF Coated Frost White.2.2.2.2.2.3.6 Color: ________.2.2.2.2.2.3.7 Color: As detailed on the Drawings.2.2.2.2.2.3.8 Color: As determined by Architect from Raynor's


2.2.2.2.2.4 Insulation: Expanded polyurethane with R-value of 24.54.2.2.2.2.3 ThermaSeal TM200:




2.2.2.2.3.3.1 Color: White polyester paint.2.2.2.2.3.4 Insulation: Expanded polyurethane with R-value of 18.3.

2.2.2.2.4 ThermaSeal TM200C:2.2.2.2.4.1 Sections shall be pressure bonded to injected polyurethane foam

insulated core. Hinge reinforcement strips shall be 20 gauge galvanized steel, located within section interior. End stiles to be 20 gauge galvanized steel.



2.2.2.2.4.3.1 Color: Almond.2.2.2.2.4.3.2 Color: Frost White.2.2.2.2.4.3.3 Color: Ivory.2.2.2.2.4.3.4 Color: Desert Tan.2.2.2.2.4.3.5 Color: Sandstone.2.2.2.2.4.3.6 Color: Beige.2.2.2.2.4.3.7 Color: Bronzetone.2.2.2.2.4.3.8 Color: Brown.2.2.2.2.4.3.9 Color: Sepia.2.2.2.2.4.3.10 Color: Battleship Grey.2.2.2.2.4.3.11 Color: Charcoal.2.2.2.2.4.3.12 Color: Slate.2.2.2.2.4.3.13 Color: Black.



2.2.2.2.5.2 Material: Steel sandwich construction, 2 inches (51 mm) thick, roll formed from commercial quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior skin shall be constructed of 20 gauge steel and interior skin shall be 26 gauge

08 36 16 -7

steel with embossed stucco texture.2.2.2.2.5.3 Finish: Exterior skin to have two coats of paint, one primer coat

and one finish coat.2.2.2.2.5.3.1 Color: White polyester paint.



2.2.2.2.6.2 Material: Steel sandwich construction, 1-3/4 inches (44 mm) thick, roll formed from commercial quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior skin shall be constructed of 25 gauge steel and interior skin shall be 26 gauge steel with embossed stucco texture.


2.2.2.2.6.3.1 Color: White polyester paint.2.2.2.2.6.3.2 Color: Dark Brown Kynar paint.

2.2.2.2.6.4 Insulation: Expanded polyurethane with R-value of 16.4.2.2.2.2.7 Seals: Interior and exterior skins to be separated by a molded thermal

break and weather seal along section joint. Bottom of door to have flexible U-shaped vinyl seal retained in aluminum rail. Optional dual-durometer vinyl blade seal on top section to prevent airflow above header

2.2.2.2.8 Trussing: Doors designed to withstand specified windload. Deflection of door in horizontal position to be maximum of 1/120th of door width.

2.2.2.3 Windows: Locations to comply with door elevation drawings.2.2.2.3.1 Window in Rectangular Two-Piece Black Frame:

2.2.2.3.1.1 Size: 24 inches by 8 inches (610 mm by 203 mm).2.2.2.3.1.1.1 Glazing: Two panes of 1/8 inch (3.2 mm) thick DSB

glass.2.2.2.3.1.1.2 Glazing: Two panes of 1/8 inch (3.2 mm) thick tempered

glass.2.2.2.3.1.1.3 Glazing: Two panes of 1/8 inch (3.2 mm) thick DSB

glass with breather tube.2.2.2.3.1.2 Size: 24 inches by 12 inches (610 mm by 305 mm).

2.2.2.3.1.2.1 Glazing: Two panes of 1/8 inch (3.2 mm) thick DSB glass.

2.2.2.3.1.2.2 Glazing: Two panes of 1/8 inch (3.2 mm) thick tempered glass.

2.2.2.3.1.2.3 Glazing: Two panes of 1/8 inch (3.2 mm) thick DSB glass with breather tube.

2.2.2.3.1.3 Size: 34 inches by 16 inches (864 mm by 406 mm) window in a rectangular two-piece black frame.

2.2.2.3.1.3.1 Glazing: Two panes of 1/8 inch (3.2 mm) thick DSB glass

2.2.2.3.2 Full-view window consisting of aluminum stile and rail construction and color matched to door exterior with powdercoat paint. Provide non-impact rated glazing as follows.

2.2.2.3.2.1 Glazing: Clear glass. One pane of 1/8 inch (3.2 mm) DSB non-insulated glass.

2.2.2.3.2.2 Glazing: Clear glass. One pane of 3/16 inch (4.8 mm) non-insulated glass.

2.2.2.3.2.3 Glazing: Clear glass. One pane of 1/4 inch (6.4 mm) non-insulated glass.

2.2.2.3.2.4 Glazing: Clear tempered glass. One pane of 1/8 inch (3.2 mm)

08 36 16 -8

non-insulated glass.2.2.2.3.2.5 Glazing: Clear tempered glass. One pane of 1/4 inch (6.4 mm)

non-insulated glass.2.2.2.3.2.6 Glazing: Clear tempered glass. One pane of 3/16 inch (4.88 mm)

non-insulated glass.2.2.2.3.2.7 Glazing: Clear laminated glass. One pane of 1/4 inch (6.4 mm)

non-insulated glass.2.2.2.3.2.8 Glazing: Clear wire glass. One pane of 1/4 inch (6.4 mm) non-

insulated glass.2.2.2.3.2.9 Glazing: Tinted bronze glass. One pane of 1/8 inch (3.2 mm) non-

insulated glass.2.2.2.3.2.10 Glazing: Laminated bronze glass. One pane of 1/4 inch (6.4 mm)

non-insulated glass.2.2.2.3.2.11 Glazing: Tinted bronze tempered glass. One pane of 1/8 inch (3.2

mm) non-insulated glass.2.2.2.3.2.12 Glazing: Tinted smoke grey laminated glass. One pane of 1/4

inch (6.4 mm) non-insulated glass.2.2.2.3.2.13 Glazing: 1/2 inch (12.7 mm) insulated clear glass. Two panes of

1/8 inch (3.2 mm) DSB insulated glass.2.2.2.3.2.14 Glazing: 1/2 inch (12.7 mm) insulated clear glass with breather

tube. Two panes of 1/8 inch (3.2 mm) DSB insulated glass.2.2.2.3.2.15 Glazing: 1/2 inch (12.7 mm) insulated clear tempered glass. Two

panes of 1/8 inch (3.2 mm) tempered insulated glass.2.2.2.3.2.16 Glazing: 1/2 inch (12.7 mm) insulated low E DSB glass. Two

panes of 1/8 inch (3.2 mm) DSB insulated glass.2.2.2.3.2.17 Glazing: 1/2 inch (12.7 mm) insulated low E tempered glass. Two

panes of 1/8 inch (3.2 mm) tempered insulated glass.2.2.2.3.2.18 Glazing: 1/2 inch (12.7 mm) insulated Solarban 60 low E

tempered glass. Two panes of 1/8 inch (3.2 mm) tempered insulated glass.

2.2.2.3.2.19 Glazing: Clear acrylic. One pane of 1/8 inch (3.2 mm).2.2.2.3.2.20 Glazing: Clear lexan. One pane of 1/8 inch (3.2 mm).2.2.2.3.2.21 Glazing: Clear acrylic. One pane of 1/4 inch (6.4 mm).2.2.2.3.2.22 Glazing: Clear lexan. One pane of 1/4 inch (6.4 mm).2.2.2.3.2.23 Glazing: 1/8 inch (3.2 mm) satin annealed glass.2.2.2.3.2.24 Glazing: 1/8 inch (3.2 mm) satin tempered glass.2.2.2.3.2.25 Glazing: 1/2 inch (12.69 mm) insulated satin glass. Two panes of

1/8 inch (3.2 mm) DSB insulated glass.2.2.2.3.2.26 Glazing: 1/2 inch (12.69 mm) insulated satin tempered glass. Two

panes of 1/8 inch (3.2 mm) tempered insulated glass.2.2.2.3.2.27 Glazing: 1/4 inch (6.4 mm) laminated white glass.2.2.2.3.2.28 Glazing: 1/8 inch (3.2 mm) smoked gray glass.2.2.2.3.2.29 Glazing: 1/8 inch (3.2 mm) smoked gray tempered glass.2.2.2.3.2.30 Glazing: 1/2 inch (12.69 mm) insulated smoked gray glass. Two

panes of 1/8 inch (3.2 mm) DSB insulated glass.2.2.2.3.2.31 Glazing: 1/2 inch (12.69 mm) insulated smoked gray glass. Two

panes of 1/8 inch (3.2 mm) tempered insulated glass.2.2.2.3.2.32 Glazing: 1/8 inch (3.2 mm) lexan smoked gray glazing.2.2.2.3.2.33 Glazing: 1/8 inch (3.2 mm) raised pattern obscure glass.2.2.2.3.2.34 Glazing: 1/8 inch (3.2 mm) raised pattern obscure tempered

glass.2.2.2.3.2.35 Glazing: 1/2 inch (12.69 mm) insulated raised pattern obscure

glass. Two panes of 1/8 inch (3.2 mm) DSB insulated glass.2.2.2.3.2.36 Glazing: 1/2 inch (12.69 mm) insulated raised pattern obscure

tempered glass. Two panes of 1/8 inch (3.2 mm) tempered insulated glass.

08 36 16 -9

2.2.2.3.2.37 Glazing: 1/2 inch (12.69 mm) insulated tinted bronze glass. Two panes of 1/8 inch (3.2 mm) DSB insulated glass.

2.2.2.3.2.38 Glazing: 1/2 inch (12.69 mm) insulated tinted bronze glass. Two panes of 1/8 inch (3.2 mm) tempered insulated glass.

2.2.2.3.2.39 Glazing: 1/4 inch (6.4 m) laminated frosted white glass.2.2.2.3.3 Full-view window consisting of aluminum stile and rail construction and

color matched to door exterior with powder coat paint. Provide non-impact rated glazing as follows.

2.2.2.3.3.1 Glazing: 1 inch (25.4 mm) Insulated Clear Glass. Two panes of 1/8 inch (3.2 mm) DSB insulated glass

2.2.2.3.3.2 Glazing: 1 inch (25.4 mm) Insulated Clear Tempered Glass. Two panes of 1/8 inch (3.2 mm) tempered insulated glass.

2.2.2.3.3.3 Glazing: 1 inch (25.4 mm) Insulated Low E DSB Glass. Two panes of 1/8 inch (3.2 mm) DSB insulated glass.

2.2.2.3.3.4 Glazing: 1 inch (25.4 mm) Insulated Low E Tempered Glass. Two panes of 1/8 inch (3.2 mm) Tempered insulated glass.

2.2.2.3.3.5 Glazing: 1 inch (25.4 mm) Insulated Satin Tempered Glass. Two panes of 1/8 inch (3.2 mm) Tempered insulated glass.







2.2.2.5.8.2 Jamb Type: Steel, wood, or masonry.2.2.2.5.8.2.1 Mounting: Floor-to-header angles. Continuous angles

from floor to door header. Angle Size: 2-5/16 x 4 x 3/32 inches (59 x 102 x 2.5 mm).






2.2.2.5.9.1.3 Mounting: QuikClip. Clip-Angle brackets pre-assembled

08 36 16 -10

to continuous angle from floor to door header and continuous angle from door header to door shaft. Angle Size: 3-1/2 x 1-1/4 x 3/32 inches (89 x 32 x 2.5 mm) on 3-inch track.












2.2.2.8 ThermaSeal Limited Warranty: Raynor warrants the door sections against defects in material and workmanship, and deterioration due to rust-through for ten years from date of delivery to the original purchaser. Raynor also warrants the door sections against delamination of the insulation from the steel skins for ten years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.

2.2.3 TH Series as manufactured by Raynor Garage Doors:2.2.3.1 Doors:




2.2.3.2 Sections:2.2.3.2.1 TH160:

2.2.3.2.1.1 Sections shall be pressure bonded to injected polyurethane foam insulated core. Hinge reinforcement strips shall be 20 gauge

08 36 16 -11

galvanized steel, located within section interior. End stiles to be 16 gauge galvanized steel.

2.2.3.2.1.2 Material: Steel sandwich construction, 1-5/8 inches (41 mm) thick, roll formed from commercial quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior skin shall be constructed of .015 thick steel and interior skin shall be 0.015 inch thick with embossed stucco texture.


2.2.3.2.1.3.1 Color: White polyester paint.2.2.3.2.1.4 Insulation: Expanded polyurethane with R-value of 14.8.

2.2.3.2.2 Seals: Interior and exterior skins to be separated by continuous hot melt to form thermal break and complete weatherseal along section joint. Bottom of door to have flexible U-shaped EPDM rubber seal retained in aluminum rail. Optional dual-durometer vinyl blade seal on top section to prevent airflow above header


2.2.3.3 Windows: Locations to comply with door elevation drawings.2.2.3.3.1 24 inches by 12 inches (610 mm by 305 mm) window in a rectangular two-

piece black frame.2.2.3.4 Glazing: Windows to be provided with insulated glazing units as follows:

2.2.3.4.1 Glass consisting of two panes of 1/8 inch (3.2 mm) thick DSB glass.2.2.3.4.2 Glass consisting of two panes of 1/8 inch (3.2 mm) thick acrylic.





adequate sealing of door to jamb or weatherseal.2.2.3.6.2 Configuration Type: Normal Headroom.2.2.3.6.3 Configuration Type: Low Headroom.2.2.3.6.4 Configuration Type: Vertical Lift.2.2.3.6.5 Configuration Type: Lift-Clearance.2.2.3.6.6 Configuration Type: Incline.2.2.3.6.7 Configuration Type: Contour.2.2.3.6.8 Track Size: 2 inches (51 mm).:







2.2.3.6.9.1.1 Mounting: Floor-to-header angles. Continuous angles

08 36 16 -12

from floor to door header. Angle Size: 3-1/2 x 5 x 3/32 inches (89 x 127 x 2.5 mm) on 3-inch track.














2.2.3.9 TH Series Limited Warranty: Raynor warrants the door sections against defects in material and workmanship, and deterioration due to rust-through for ten years from date of delivery to the original purchaser. Raynor also warrants the door sections against delamination of the insulation from the steel skins for ten years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.

2.2.4 FlexFit Series as manufactured by Raynor Garage Doors:2.2.4.1 Doors:



08 36 16 -13


2.2.4.2 Sections:2.2.4.2.1 FF175:

2.2.4.2.1.1 Sections shall contain 1.44 inch expanded polystyrene insulation sandwiched between interior and exterior panels. End stiles to be 12-gauge galvanized steel.

2.2.4.2.1.2 Material: Sandwich construction, 1-3/4 inches (44 mm) thick. Exterior skin shall be constructed of 1/8 inch (3 mm) non-conductive, UV stabilized FgR pultruded fiberglass reinforced polymer (FRP) material with additional anti-yellowing UV protective coating. Interior skin shall be constructed of 1/8 inch IDS extruded HDPE and manufactured with materials in compliance with FDA regulation 21 CFR 177.1520. Skins will be bolted together around 1.5 inch (38 mm)x 1/8 inch (3 mm) FgS square tube framing constructed of pultruded fiberglass reinforced polymer (FRP). Bolts shall be carriage style heads on exterior and blind-head style on interior to reduce risk of injury.

2.2.4.2.1.2.1 Interior and exterior skins shall be one contiguous piece without splices up to 20 feet 2 inches (6146 mm) in length.

2.2.4.2.1.2.2 Square tube frame rails shall be one contiguous piece without splices up to 20 feet (6096 mm) in length.

2.2.4.2.1.3 Finish: Exterior and interior skins to have smooth finish.2.2.4.2.1.3.1 Color: White.

2.2.4.2.1.4 Insulation: Expanded polystyrene with door R-value of 9.68.2.2.4.2.2 Seals: Intermediate sections will incorporate white, J-Flex fabric reinforced

section joint seals. Bottom of door to have flexible cloth reinforced U-shaped EPDM rubber seal and 3 inch (76 mm) brush seal. Header shall have dual-durometer vinyl blade seal on top section to prevent airflow above header. Jambs shall have 1 inch (25 mm) brush seals to prevent airflow. Brush seals will be mounted into continuous (no splices) extruded aluminum retainers.

2.2.4.2.3 Trussing: Not applicable.2.2.4.3 Windows: 12 x 4 inches (305 x 102 mm) window with 1/8 inch (3.1 mm)

polycarbonate lite.2.2.4.4 Mounting: Sections mounted in door opening using:

2.2.4.4.1 Between-Jamb Bracket Mounting: sections mounted between door jambs, seal against exterior perimeter seal installed along vertical and top horizontal edges of jambs.



adequate sealing of door to jamb or weather seal.2.2.4.5.2 Configuration Type: Normal Headroom.2.2.4.5.3 Configuration Type: Vertical Lift.2.2.4.5.4 Configuration Type: Lift-Clearance.2.2.4.5.5 Track Size: 3 inches (76 mm).


from floor to door header. Angle Size: 3-1/2 x 5 x 3/32 inches (89 x 127 x 2.5 mm) on 3-inch track.


2.2.4.5.6 Finish:

08 36 16 -14

2.2.4.5.6.1 Galvanized.2.2.4.6 Counterbalance:

2.2.4.6.1 Counterbalance System: Provided with aircraft-type, galvanized steel lifting cables with minimum safety factor of 5. Torsion Springs consisting of heavy-duty oil-tempered wire torsion springs on a continuous ball-bearing cross-header shaft.

2.2.4.6.1.1 Spring Cycle Requirements: Standard high cycle 25,000 cycles.2.2.4.6.1.2 Spring Cycle Requirements: Extended cycle: ___________

cycles.2.2.4.7 Hardware:

2.2.4.7.1 End Stile Hinges and Brackets: Fabricated from galvanized steel.2.2.4.7.2 Track Rollers: 3 inches (76.2 mm) diameter consistent with track size, with

hardened steel ball bearings.2.2.4.7.3 Locks: Door furnished with one spring-loaded interior lock with dead bolt

provided with hole to receive padlock provided by Owner.2.2.4.8 FlexFit Limited Warranty: Raynor warrants the door sections against defects in

material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.

2.2.5 Commercial BuildMark/TradeMark as manufactured by Raynor Garage Doors:2.2.5.1 Doors:




2.2.5.2 Sections:2.2.5.2.1 Commercial TradeMark:

2.2.5.2.1.1 Section end stiles to be 18 gauge galvanized steel and center stiles to be 20 gauge galvanized steel. End stiles to be crimp-locked to the section skin. Center stiles to be glued and crimp-locked to section skin.

2.2.5.2.1.2 Material: Steel pan construction, 2 inches (51 mm) thick, roll formed from 24 gauge draw quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior surface of sections shall feature embossed Colonial Raised Panels or Ranch Raised Panels. Sections shall have tongue-and-groove joints for weather-tight closure.


2.2.5.2.1.3.1 Color: White polyester paint.2.2.5.2.1.3.2 Color: Almond polyester paint.2.2.5.2.1.3.3 Color: BronzeTone polyester paint.2.2.5.2.1.3.4 Color: Sandstone polyester paint.2.2.5.2.1.3.5 Color: Dark brown polyester paint.2.2.5.2.1.3.6 Color: ________.2.2.5.2.1.3.7 Color: As detailed on the Drawings.

08 36 16 -15

2.2.5.2.1.3.8 Color: As determined by Architect from Raynor's ColorWave post paint process featuring 1500 colors of Sherwin Williams Polane Enamel paint.

2.2.5.2.1.4 Insulation: Expanded polystyrene with R-value of 6.6 with white impact-resistant textured covers.

2.2.5.2.2 Commercial BuildMark:2.2.5.2.2.1 Section end stiles to be 18 gauge galvanized steel and center

stiles to be 20 gauge galvanized steel. End stiles to be crimp-locked to the section skin. Center stiles to be glued and crimp-locked to section skin.

2.2.5.2.2.2 Material: Steel pan construction, 2 inches (51 mm) thick, roll formed from 25 gauge draw quality, hot-dipped galvanized (G40 exterior) steel complying with ASTM A 653. Exterior surface of sections shall feature embossed Colonial Raised Panels, Ranch Raised Panels, or Flush Woodgrain Surface. Sections shall have tongue-and-groove joints for weather-tight closure.


2.2.5.2.2.3.1 Color: White polyester paint.2.2.5.2.2.3.2 Color: Almond polyester paint.2.2.5.2.2.3.3 Color: Sandstone polyester paint.2.2.5.2.2.3.4 Color: Desert tan polyester paint.2.2.5.2.2.3.5 Color: Black polyester paint.2.2.5.2.2.3.6 Color: Auburn woodtone polyester paint.2.2.5.2.2.3.7 Color: Mocha woodtone polyester paint.2.2.5.2.2.3.8 Color: Walnut woodtone polyester paint.2.2.5.2.2.3.9 Color: ________.2.2.5.2.2.3.10 Color: As detailed on the Drawings.2.2.5.2.2.3.11 Color: As determined by Architect from Raynor's


2.2.5.2.2.4 Insulation: Expanded polystyrene with R-value of 6.6 with white impact-resistant textured covers.

2.2.5.2.3 Seals: Bottom of door to have flexible U-shaped vinyl seal retained in aluminum rail. Optional blade seal on top section to prevent airflow above header


2.2.5.3 Windows: Locations to comply with door elevation drawings.2.2.5.3.1 Colonial style 18 inches by 13 inches (457 mm by 330 mm) minimum

window encased in an injection molded polypropylene frame.2.2.5.3.2 Ranch style 41 inches by 13 inches (1041 mm by 330 mm) window

minimum encased in an injection molded polypropylene frame.2.2.5.4 Glazing: Windows to be provided with glazing units as follows:

2.2.5.4.1 Single glass consisting of one pane of 1/8 inch (3.2 mm) thick DSB glass.2.2.5.5 Mounting: Sections mounted in door opening using:




adequate sealing of door to jamb or weatherseal.2.2.5.6.2 Configuration Type: Normal Headroom.2.2.5.6.3 Configuration Type: Low Headroom.

08 36 16 -16

2.2.5.6.4 Configuration Type: Vertical Lift.2.2.5.6.5 Configuration Type: Lift-Clearance.2.2.5.6.6 Configuration Type: Incline.2.2.5.6.7 Configuration Type: Contour.2.2.5.6.8 Track Size: 2 inches (51 mm).





















2.2.5.9 Commercial BuildMark, Commercial TradeMark Series Limited Warranty:

08 36 16 -17

Raynor warrants the door sections against defects in material and workmanship, and deterioration due to rust-through for ten years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.

2.2.6 ControlHoist as manufactured by Raynor Garage Doors:2.2.6.1 Model:

2.2.6.1.1 Raynor ControlHoist COH, COT:2.2.6.1.1.1 Type: Jackshaft with manual chain hoist.2.2.6.1.1.2 Type: Trolley.2.2.6.1.1.3 Motor Horsepower Rating: Continuous 1/2 HP.2.2.6.1.1.4 Motor Horsepower Rating: Continuous 3/4 HP.2.2.6.1.1.5 Motor Horsepower Rating: Continuous 1 HP.2.2.6.1.1.6 Motor Horsepower Rating: Continuous 1-1/2 HP.2.2.6.1.1.7 Motor Horsepower Rating: Continuous 2 HP.2.2.6.1.1.8 Electrical Requirements: 115 volt single phase.2.2.6.1.1.9 Electrical Requirements: 230 volt single phase.2.2.6.1.1.10 Electrical Requirements: 208-230 volt three phase.2.2.6.1.1.11 Electrical Requirements: 460 volt three phase.2.2.6.1.1.12 Duty Cycle: 30 cycles/hour or 300 cycles/day.2.2.6.1.1.13 Control Wiring: Solid state circuitry with provisions for connection

of safety edge to reverse, external radio control hook-up and maximum run timer. Provisions for timers to close, monitored reversing devices, mid stop and lock bar sensor capability.

2.2.6.1.1.13.1 Provide three button momentary contact "open-stop", constant pressure on close (can be changed to momentary to close).

2.2.6.1.1.13.2 Custom wiring.2.2.6.1.2 Raynor ControlHoist CSJ, CSH, CST :

2.2.6.1.2.1 Type: Jackshaft.2.2.6.1.2.2 Type: Jackshaft with manual chain hoist.2.2.6.1.2.3 Type: Trolley.2.2.6.1.2.4 Motor Horsepower Rating: Continuous 1/3 HP.2.2.6.1.2.5 Motor Horsepower Rating: Continuous 1/2 HP.2.2.6.1.2.6 Motor Horsepower Rating: Continuous 3/4 HP.2.2.6.1.2.7 Electrical Requirements: 115 volt single phase.2.2.6.1.2.8 Electrical Requirements: 230 volt single phase.2.2.6.1.2.9 Electrical Requirements: 208-230 volt three phase.2.2.6.1.2.10 Electrical Requirements: 460 volt three phase.2.2.6.1.2.11 Duty Cycle: 30 cycles/hour or 300 cycles/day.2.2.6.1.2.12 Control Wiring: Solid state circuitry with provisions for connection



2.2.6.1.2.12.2 Custom wiring.2.2.6.1.3 Raynor ControlHoist CMJ, CMH, CMT :

2.2.6.1.3.1 Type: Jackshaft.2.2.6.1.3.2 Type: Jackshaft with manual chain hoist.

08 36 16 -18

2.2.6.1.3.3 Type: Trolley.2.2.6.1.3.4 Motor Horsepower Rating: Intermittent 1/2 HP.2.2.6.1.3.5 Electrical Requirements: 115 volt single phase.2.2.6.1.3.6 Duty Cycle: 14 cycles/hour.2.2.6.1.3.7 Control Wiring: Solid state circuitry with provisions for connection



2.3 SECTIONAL RIBBED PAN DOOR

2.3.1 SteelForm as manufactured by Raynor Garage Doors:2.3.1.1 Doors:




2.3.1.2 Sections:2.3.1.2.1 SteelForm S16 (Optima):

2.3.1.2.1.1 Section end stiles to be 13 gauge galvanized steel. Center stiles to be a minimum 16 gauge thickness. End stiles and center stiles to be riveted to outside face with stainless steel rivets and resistance welded to interior rail.

2.3.1.2.1.2 Material: Steel pan construction, 2 inches (51 mm) thick, roll formed from 16 gauge draw-quality, hot-dipped galvanized (G90) steel complying with ASTM A 653. Exterior of door to have flush face and roll-formed tongue and groove joints for weathertight closure.


2.3.1.2.1.3.1 Color: White polyester paint.2.3.1.2.2 SteelForm S20 (Standard):

2.3.1.2.2.1 Section end stiles to be 13 gauge galvanized steel. Center stiles to be a minimum 16 gauge thickness. End stiles and center stiles to be riveted to outside face with stainless steel rivets and resistance welded to interior rail.

2.3.1.2.2.2 Material: Steel pan construction, 2 inches (51 mm) thick, roll-formed from 20 gauge commercial quality, hot-dipped galvanized (G90) steel complying with ASTM A 653. Exterior of door to have flush face and roll-formed tongue and groove joints for weathertight closure.


2.3.1.2.2.3.1 Color: White polyester paint.2.3.1.2.3 SteelForm S24 (Standard):

2.3.1.2.3.1 Section end stiles and center stiles to be minimum 16 gauge galvanized steel. End stiles and center stiles to be riveted to

08 36 16 -19

outside face with stainless steel rivets and resistance welded to interior rail.

2.3.1.2.3.2 Material: Steel pan construction, 2 inches (51 mm) thick, roll- formed from 24 gauge commercial quality, hot-dipped galvanized (G60) steel complying with ASTM A 653. Exterior of door to have two deep ribs, four pencil grooves, and roll-formed tongue-and-groove joints for weathertight closure.


2.3.1.2.3.3.1 Color: White polyester paint.2.3.1.2.3.3.2 Color: Dark Brown Kynar paint.2.3.1.2.3.3.3 Color: Frost White Kynar paint.2.3.1.2.3.3.4 Color: Beige Kynar paint.2.3.1.2.3.3.5 Color: Sepia Brown Kynar paint.2.3.1.2.3.3.6 Color: ________.2.3.1.2.3.3.7 Color: As detailed on the Drawings.2.3.1.2.3.3.8 Color: As determined by Architect from Raynor's


2.3.1.2.4 SteelForm S24C (Basic):2.3.1.2.4.1 Section end stiles and center stiles to be a minimum 16 gauge

galvanized steel. End stiles and center stiles to be riveted to outside face with stainless steel rivets and resistance welded to interior rail.

2.3.1.2.4.2 Material: Steel pan construction, 2 inches (51 mm) thick, roll formed from 24 gauge embossed thickness, commercial quality, hot-dipped galvanized (G40) steel complying with ASTM A 653. Exterior of door to have two deep ribs, four pencil grooves, and roll-formed tongue-and-groove joints for weathertight closure.


2.3.1.2.4.3.1 Color: White polyester paint.2.3.1.2.5 Insulation:

2.3.1.2.5.1 Expanded polystyrene with R-value of 7.70 with white impact-resistant textured covers.

2.3.1.2.5.2 Expanded polystyrene with R-value of 7.70 with 26 gauge hot-dipped galvanized steel covers, stucco embossed and painted gray.

2.3.1.2.5.3 Expanded polystyrene with R-value of 7.70 with 24 gauge hot-dipped galvanized steel covers, painted gray/white.

2.3.1.2.5.4 Expanded polystyrene with R-value of 7.70 with 20 gauge hot-dipped galvanized steel covers, painted gray/white.



2.3.1.3 Windows: Locations to comply with door elevation drawings.2.3.1.3.1 24 inches by 8 inches (610 mm by 203 mm) rectangular window encased

in a two-piece black frame.2.3.1.3.2 Full-view window consisting of aluminum stile and rail construction and

color matched to door exterior with powdercoat paint.2.3.1.4 Glazing: Windows to be provided as follows:

2.3.1.4.1 Glass consisting of one pane of 1/8 inch (3.2 mm) thick DSB glass.2.3.1.5 Glazing: Windows to be provided with insulated glazing units as follows:

2.3.1.5.1 Glass consisting of two panes of 1/8 inch (3.2 mm) thick DSB glass.

08 36 16 -20

2.3.1.6 Glazing: Full View to be provided as follows:2.3.1.6.1 Impact Rated Glazing: 11/32 inch (8.37 mm) Clear Impact Glass.2.3.1.6.2 Impact Rated Glazing: 11/32 inch (8.37 mm) Tinted Bronzer Impact Glass.2.3.1.6.3 Impact Rated Glazing: 11/32 inch (8.37 mm) Tinted Green Impact Glass.2.3.1.6.4 Impact Rated Glazing: 11/32 inch (8.37 mm) White Interlayer Impact Glass.2.3.1.6.5 Non-Impact Rated Glazing: 1/8 inch (3.2 mm) Clear Glass consisting of

one pane of 1/8 inch (3.2 mm) DSB non-insulated glass.2.3.1.6.6 Non-Impact Rated Glazing: 3/16 inch (4.8 mm) Clear Glass consisting of

one pane of 3/16 inch (4.8 mm) non-insulated glass.2.3.1.6.7 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Clear Glass consisting of

one pane of 1/4 inch (6.4 mm) non-insulated glass.2.3.1.6.8 Non-Impact Rated Glazing: 1/8 inch (3.2 mm) Clear Tempered Glass

consisting of one pane of 1/8 inch (3.2 mm) non-insulated glass.2.3.1.6.9 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Clear Tempered Glass

consisting of one pane of 1/4 inch (6.4 mm) non-insulated glass.2.3.1.6.10 Non-Impact Rated Glazing: 3/16 inch (4.88 mm) Clear Tempered Glass

consisting of one pane of 3/16 inch (4.88 mm) non-insulated glass.2.3.1.6.11 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Clear Laminated Glass

consisting of one pane of 1/4 inch (6.4 mm) non-insulated glass.2.3.1.6.12 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Clear Wire Glass consisting

of one pane of 1/4 inch (6.4 mm) non-insulated glass.2.3.1.6.13 Non-Impact Rated Glazing: 1/8 inch (3.2 mm) Tinted Glass consisting of

one pane of 1/8 inch (3.2 mm) non-insulated glass.2.3.1.6.14 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Tinted Glass consisting of

one pane of 1/4 inch (6.4 mm) non-insulated glass.2.3.1.6.15 Non-Impact Rated Glazing: 1/8 inch (3.2 mm) Tinted Tempered Glass

consisting of one pane of 1/8 inch (3.2 mm) non-insulated glass.2.3.1.6.16 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Tinted Tempered Glass

consisting of one pane of 1/4 inch (6.4 mm) non-insulated glass.2.3.1.6.17 Non-Impact Rated Glazing: 1/2 inch (12.69 mm) Insulated Clear Glass

consisting of two panes of 1/8 inch (3.2 mm) DSB insulated glass.2.3.1.6.18 Non-Impact Rated Glazing: 1/2 inch (12.69 mm) Insulated Clear Tempered

Glass consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.

2.3.1.6.19 Non-Impact Rated Glazing: 1/2 inch (12.69 mm) Insulated Low E DSB Glass consisting of two panes of 1/8 inch (3.2 mm) DSB insulated glass.

2.3.1.6.20 Non-Impact Rated Glazing: 1/2 inch (12.69 mm) Insulated Low E Tempered Glass consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.

2.3.1.6.21 Non-Impact Rated Glazing: 1/8 inch (3.2 mm) Clear Acrylic consisting of one pane of 1/8 inch (3.2 mm) Acrylic glazing.

2.3.1.6.22 Non-Impact Rated Glazing: 1/8 inch (3.2 mm) Clear Lexan consisting of one pane of 1/8 inch (3.2 mm) Lexan glazing.

2.3.1.6.23 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Clear Acrylic consisting of one pane of 1/4 inch (6.4 mm) Acrylic glazing.

2.3.1.6.24 Non-Impact Rated Glazing: 1/4 inch (6.4 mm) Clear Lexan consisting of one pane of 1/4 inch (6.4 mm) Lexan glazing.





adequate sealing of door to jamb or weatherseal.

08 36 16 -21

2.3.1.8.2 Configuration Type: Normal Headroom.2.3.1.8.3 Configuration Type: Low Headroom.2.3.1.8.4 Configuration Type: Vertical Lift.2.3.1.8.5 Configuration Type: Lift-Clearance.2.3.1.8.6 Configuration Type: Incline.2.3.1.8.7 Configuration Type: Contour.2.3.1.8.8 Track Size: 2 inches (51 mm).




















2.3.1.10.6 Furnish door system with locks: Interior lock with dead bolt provided with

08 36 16 -22

hole to receive padlock provided by Owner.2.3.1.11 SteelForm Limited Warranty: Raynor warrants the door sections against defects

in material and workmanship, and deterioration due to rust-through for ten years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.





2.3.2.1.1.13.2 Custom wiring.2.3.2.1.2 Raynor ControlHoist CSJ, CSH, CST:




2.3.2.1.2.12.2 Custom wiring.2.3.2.1.3 Raynor ControlHoist CMJ, CMH, CMT:

2.3.2.1.3.1 Type: Jackshaft.

08 36 16 -23

2.3.2.1.3.2 Type: Jackshaft with manual chain hoist.2.3.2.1.3.3 Type: Trolley.2.3.2.1.3.4 Motor Horsepower Rating: Intermittent 1/2 HP.2.3.2.1.3.5 Electrical Requirements: 115 volt single phase.2.3.2.1.3.6 Duty Cycle: 14 cycles/hour.2.3.2.1.3.7 Control Wiring: Solid state circuitry with provisions for connection



2.4 SECTIONAL RAIL AND STYLE ALUMINUM DOORS

2.4.1 AlumaView as manufactured by Raynor Garage Doors:2.4.1.1 Doors:



2.4.1.1.3 Structural Performance Requirements:2.4.1.1.3.1 Wind Load (Model AV 300 only): Florida Building Code Product

Approval #FL16225 large missile impact.2.4.1.1.3.2 Wind Load (Model AV 200 only): Florida Building Code Product

Approval #FL15212 large missile impact.2.4.1.1.3.3 Wind Load (Model AV 200 only): Florida Building Code Product

Approval #FL114092 non-impact.2.4.1.1.3.4 Wind Load: Florida Building Code Product Approval ______.2.4.1.1.3.5 Wind Loads: Uniform pressure of: ________ psf.

2.4.1.1.4 International Energy Conservation Code (IECC) Requirements:2.4.1.1.4.1 Air Infiltration: Maximum air leakage of 0.4 cfm/ft2 is required.

Testing shall be performed in accordance with DASMA 105 test procedure.

2.4.1.1.4.2 AV200 with IG Low E Glass has a Tested U-Factor of 0.72.2.4.1.1.4.3 Raynor AV300 and AV200 provide an air leakage rating of 0.24

cfm/ft2 with optional IECC Compliance Package.2.4.1.2 Sections:

2.4.1.2.1 AlumaView AV300:2.4.1.2.1.1 Material: 3 inches (76 mm) thick, 6063-T6 aluminum alloy stiles

and rails joined together with 5/16 inch (8 mm) diameter screws. Aluminum panels 0.050 inch (1.3 mm) thick or glazing (when specified) fill the spaces between stiles and rails. Combined dimension of two adjoining intermediate meeting rails 5 inches (127 mm). Bottom rail height 6-1/2 inches (165 mm). Top rail height 6-1/2 inches (165 mm). End stiles 3-3/8 inches (86 mm) or 6-1/2 inches (165 mm) wide as determined by overall door width. Center stiles 3-5/8 inches (92 mm) wide.

2.4.1.2.1.2 Finish: Aluminum frame extrusions and filler panels finish coated.2.4.1.2.1.2.1 Color: Clear anodized finish.2.4.1.2.1.2.2 Color: Champagne anodized finish.2.4.1.2.1.2.3 Color: Light Bronze anodized finish.

08 36 16 -24

2.4.1.2.1.2.4 Color: Medium Bronze anodized finish.2.4.1.2.1.2.5 Color: Dark Bronze anodized finish.2.4.1.2.1.2.6 Color: Extra Dark Bronze anodized finish.2.4.1.2.1.2.7 Color: Black anodized finish.2.4.1.2.1.2.8 ArmorBrite Powdercoat finish, color as selected by

Architect.2.4.1.2.1.2.9 American Douglas powdercoat finish.2.4.1.2.1.2.10 American Maple powdercoat finish.2.4.1.2.1.2.11 Cherry powdercoat finish.2.4.1.2.1.2.12 Cherry With Flame powdercoat finish.2.4.1.2.1.2.13 Colony Maple powdercoat finish.2.4.1.2.1.2.14 Dark Walnut powdercoat finish.2.4.1.2.1.2.15 European Cherry powdercoat finish.2.4.1.2.1.2.16 Golden Oak powdercoat finish.2.4.1.2.1.2.17 Knotty Pine powdercoat finish.2.4.1.2.1.2.18 National Walnut powdercoat finish.2.4.1.2.1.2.19 Oak powdercoat finish.2.4.1.2.1.2.20 Oregon Douglas powdercoat finish.2.4.1.2.1.2.21 Table Cherry powdercoat finish.2.4.1.2.1.2.22 Teak powdercoat finish.

2.4.1.2.2 AlumaView AV200:2.4.1.2.2.1 Material: 2 inches (51 mm) thick, 6063-T6 aluminum alloy stiles

and rails joined together with 5/16 inch (8 mm) diameter screws. Aluminum panels 0.050 inch (1.3 mm) thick or glazing (when specified) fill the spaces between stiles and rails. Combined dimension of two adjoining intermediate meeting rails 3-13/16 inches (97 mm). Bottom rail height 5-1/4 inches (133 mm). Top rail height 3-1/4 inches (83 mm) or 5-1/4 inches (133 mm) as determined by overall door width. End stiles 3-3/8 inches (86 mm) or 6-1/2 inches (165 mm) wide as determined by overall door width. Center stiles 3-5/8 inches (92 mm) wide.

2.4.1.2.2.2 Optional Insulation: Extruded polystyrene provides an R-value of 4.31 when combined with double endstiles and 1/2 inch (13 mm) insulated Low-E Glass.

2.4.1.2.2.3 Finish: Aluminum frame extrusions and filler panels finish coated.2.4.1.2.2.3.1 Color: Clear anodized finish.2.4.1.2.2.3.2 Color: Champagne anodized finish.2.4.1.2.2.3.3 Color: Light Bronze anodized finish.2.4.1.2.2.3.4 Color: Medium Bronze anodized finish.2.4.1.2.2.3.5 Color: Dark Bronze anodized finish.2.4.1.2.2.3.6 Color: Extra Dark Bronze anodized finish.2.4.1.2.2.3.7 Color: Black anodized finish.2.4.1.2.2.3.8 ArmorBrite Powdercoat finish, color as selected by

Architect.2.4.1.2.2.3.9 American Douglas powdercoat finish.2.4.1.2.2.3.10 American Maple powdercoat finish.2.4.1.2.2.3.11 Cherry powdercoat finish.2.4.1.2.2.3.12 Cherry With Flame powdercoat finish.2.4.1.2.2.3.13 Colony Maple powdercoat finish.2.4.1.2.2.3.14 Dark Walnut powdercoat finish.2.4.1.2.2.3.15 European Cherry powdercoat finish.2.4.1.2.2.3.16 Golden Oak powdercoat finish.2.4.1.2.2.3.17 Knotty Pine powdercoat finish.2.4.1.2.2.3.18 National Walnut powdercoat finish.2.4.1.2.2.3.19 Oak powdercoat finish.2.4.1.2.2.3.20 Oregon Douglas powdercoat finish.

08 36 16 -25

2.4.1.2.2.3.21 Table Cherry powdercoat finish.2.4.1.2.2.3.22 Teak powdercoat finish.

2.4.1.2.3 AlumaView AV175:2.4.1.2.3.1 Material: 1-3/4 inches (44 mm) thick, 6063-T6 aluminum alloy

stiles and rails joined together with 5/16 inch (8 mm) diameter screws. Aluminum panels 0.050 inch (1.3 mm) thick or glazing (when specified) fill the spaces between stiles and rails. Combined dimension of two adjoining intermediate meeting rails 3-1/4 inches (83 mm). Bottom rail and top rail height 5-3/16 inches (132 mm). End stiles 3-3/8 inches (86 mm) or 6-1/2 inches (165 mm) wide as determined by overall door width. Center stiles 1-7/16 inches (36 mm), 2 inches (51 mm), or 3-5/8 inches (92 mm) wide.

2.4.1.2.3.2 Finish: Aluminum frame extrusions and filler panels finish coated.2.4.1.2.3.2.1 Color: Clear anodized finish.2.4.1.2.3.2.2 Color: Champagne anodized finish.2.4.1.2.3.2.3 Color: Light Bronze anodized finish.2.4.1.2.3.2.4 Color: Medium Bronze anodized finish.2.4.1.2.3.2.5 Color: Dark Bronze anodized finish.2.4.1.2.3.2.6 Color: Extra Dark Bronze anodized finish.2.4.1.2.3.2.7 Color: Black anodized finish.2.4.1.2.3.2.8 ArmorBrite Powdercoat finish, color as selected by

Architect.2.4.1.2.3.2.9 American Douglas powdercoat finish.2.4.1.2.3.2.10 American Maple powdercoat finish.2.4.1.2.3.2.11 Cherry powdercoat finish.2.4.1.2.3.2.12 Cherry With Flame powdercoat finish.2.4.1.2.3.2.13 Colony Maple powdercoat finish.2.4.1.2.3.2.14 Dark Walnut powdercoat finish.2.4.1.2.3.2.15 European Cherry powdercoat finish.2.4.1.2.3.2.16 Golden Oak powdercoat finish.2.4.1.2.3.2.17 Knotty Pine powdercoat finish.2.4.1.2.3.2.18 National Walnut powdercoat finish.2.4.1.2.3.2.19 Oak powdercoat finish.2.4.1.2.3.2.20 Oregon Douglas powdercoat finish.2.4.1.2.3.2.21 Table Cherry powdercoat finish.2.4.1.2.3.2.22 Teak powdercoat finish.

2.4.1.2.4 Seals: Bottom of door to have flexible U-shaped vinyl seal retained in aluminum rail.

2.4.1.2.4.1 Bulb-type joint seal between sections.2.4.1.2.4.2 Blade seal on top section to prevent airflow above header.


2.4.1.3 Windows: Provide door sections with windows in lieu of 0.050 inch (1.3 mm) aluminum filler panels. Locations to comply with door elevation drawings.

2.4.1.4 Impact Rated Glazing: Provide as follows.2.4.1.4.1 11/32 inch (8.7 mm) Clear Impact Glass2.4.1.4.2 11/32 inch (8.7 mm) Tinted Bronze Impact Glass2.4.1.4.3 11/32 inch (8.7 mm) Tinted Gray Impact Glass2.4.1.4.4 11/32 inch (8.7 mm) Tinted Green Impact Glass2.4.1.4.5 11/32 inch (8.7 mm) White Interlayer Impact Glass

2.4.1.5 Non-Impact Rated Glazing: Provide as follows:2.4.1.5.1 1/8 inch (3.2 mm) Clear Glass consisting of one pane of 1/8 inch (3.2 mm)

DSB non-insulated glass.2.4.1.5.2 3/16 inch (4.8 mm) Clear Glass consisting of one pane of 3/16 inch (4.8

mm) non-insulated glass.2.4.1.5.3 1/4 inch (6.4 mm) Clear Glass consisting of one pane of 1/4 inch (6.4 mm)

08 36 16 -26

non-insulated glass.2.4.1.5.4 1/8 inch (3.2 mm) Clear Tempered Glass consisting of one pane of 1/8

inch (3.2 mm) non-insulated glass.2.4.1.5.5 1/4 inch (6.4 mm) Clear Tempered Glass consisting of one pane of 1/4

inch (6.4 mm) non-insulated glass.2.4.1.5.6 3/16 inch (4.88 mm) Clear Tempered Glass consisting of one pane of 3/16

inch (4.88 mm) non-insulated glass.2.4.1.5.7 1/4 inch (6.4 mm) Clear Laminated Glass consisting of one pane of 1/4

inch (6.4 mm) non-insulated glass.2.4.1.5.8 1/4 inch (6.4 mm) Bronze Tinted Laminated Glass consisting of one pane

of 1/4 inch (6.4 mm) non-insulated glass.2.4.1.5.9 1/4 inch (6.4 mm) Smoked Grey Tinted Laminated Glass consisting of one

pane of 1/4 inch (6.4 mm) non-insulated glass.2.4.1.5.10 1/4 inch (6.4 mm) Satin Laminated Glass consisting of one pane of 1/4

inch (6.4 mm) non-insulated glass.2.4.1.5.11 1/4 inch (6.4 mm) White Laminated Glass consisting of one pane of 1/4

inch (6.4 mm) non-insulated glass.2.4.1.5.12 1/4 inch (6.4 mm) Clear Wire Glass consisting of one pane of 1/4 inch (6.4

mm) non-insulated glass.2.4.1.5.13 1/8 inch (3.2 mm) Bronze Tinted Glass consisting of one pane of 1/8 inch

(3.2 mm) non-insulated glass.2.4.1.5.14 1/8 inch (3.2 mm) Smoked Grey Tinted Glass consisting of one pane of 1/8

inch (3.2 mm) non-insulated glass.2.4.1.5.15 1/8 inch (3.2 mm) Black Privacy Glass consisting of one pane of 1/8 inch

(3.2 mm) non-insulated glass.2.4.1.5.16 1/8 inch (3.2 mm) Satin Glass consisting of one pane of 1/8 inch (3.2 mm)

non-insulated glass.2.4.1.5.17 1/8 inch (3.2 mm) Raised Obscure Glass consisting of one pane of 1/8 inch

(3.2 mm) non-insulated glass.2.4.1.5.18 1/8 inch (3.2 mm) Bronze Tinted Tempered Glass consisting of one pane

of 1/8 inch (3.2 mm) non-insulated glass.2.4.1.5.19 1/8 inch (3.2 mm) Smoked Grey Tinted Tempered Glass consisting of one

pane of 1/8 inch (3.2 mm) non-insulated glass.2.4.1.5.20 1/8 inch (3.2 mm) Black Privacy Tempered Glass consisting of one pane of

1/8 inch (3.2 mm) non-insulated glass.2.4.1.5.21 1/8 inch (3.2 mm) Satin Tempered Glass consisting of one pane of 1/8 inch

(3.2 mm) non-insulated glass.2.4.1.5.22 1/8 inch (3.2 mm) Raised Obscure Glass consisting of one pane of 1/8 inch

(3.2 mm) non-insulated glass.2.4.1.5.23 1/2 inch (12.69 mm) Insulated Clear Glass consisting of two panes of 1/8

inch (3.2 mm) DSB insulated glass.2.4.1.5.24 1/2 inch (12.69 mm) Insulated Clear Glass with Breather Tube consisting

of two panes of 1/8 inch (3.2 mm) DSB insulated glass.2.4.1.5.25 1/2 inch (12.69 mm) Insulated Clear Tempered Glass consisting of two

panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.26 1/2 inch (12.69 mm) Insulated Clear Tempered Glass with Breather Tube

consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.27 1/2 inch (12.69 mm) Insulated Bronze Tinted Glass consisting of two panes

of 1/8 inch (3.2 mm) DSB insulated glass.2.4.1.5.28 1/2 inch (12.69 mm) Insulated Bronze Tinted Tempered Glass consisting of

two panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.29 1/2 inch (12.69 mm) Insulated Smoked Grey Tinted Glass consisting of two

panes of 1/8 inch (3.2 mm) DSB insulated glass.2.4.1.5.30 1/2 inch (12.69 mm) Insulated Smoked Grey Tinted Tempered Glass

consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.31 1/2 inch (12.69 mm) Insulated Satin Glass consisting of two panes of 1/8

08 36 16 -27

inch (3.2 mm) DSB insulated glass.2.4.1.5.32 1/2 inch (12.69 mm) Insulated Satin Tempered Glass consisting of two

panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.33 1/2 inch (12.69 mm) Insulated Raised Obscure Glass consisting of two

panes of 1/8 inch (3.2 mm) DSB insulated glass.2.4.1.5.34 1/2 inch (12.69 mm) Insulated Raised Obscure Tempered Glass consisting

of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.35 1/2 inch (12.69 mm) Insulated Low E DSB Glass consisting of two panes of

1/8 inch (3.2 mm) DSB insulated glass.2.4.1.5.36 1/2 inch (12.69 mm) Insulated Low E Tempered Glass consisting of two

panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.37 1/2 inch (12.69 mm) Insulated Solarban 60 Low E Tempered Glass

consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.38 1/8 inch (3.2 mm) Clear Acrylic consisting of one pane of 1/8 inch (3.2 mm)

Acrylic glazing.2.4.1.5.39 1/8 inch (3.2 mm) Clear Lexan consisting of one pane of 1/8 inch (3.2 mm)

Lexan glazing.2.4.1.5.40 1/8 inch (3.2 mm) Smoked Grey Tinted Lexan consisting of one pane of

1/8 inch (3.2 mm) Lexan glazing.2.4.1.5.41 1/4 inch (6.4 mm) Clear Acrylic consisting of one pane of 1/4 inch (6.4 mm)

Acrylic glazing.2.4.1.5.42 1/4 inch (6.4 mm) Clear Lexan consisting of one pane of 1/4 inch (6.4 mm)

Lexan glazing.2.4.1.5.43 1/2 inch (12.69 mm) Insulated Bronze Tinted Low E DSB Glass consisting

of two panes of 1/8 inch (3.2 mm) DSB insulated glass.2.4.1.5.44 1/2 inch (12.69 mm) Insulated Smoked Grey Tinted Low E DSB Glass

consisting of two panes of 1/8 inch (3.2 mm) DSB insulated glass.2.4.1.5.45 1/2 inch (12.69 mm) Insulated Bronze Tinted Low E Tempered Glass

consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.2.4.1.5.46 1/2 inch (12.69 mm) Insulated Smoked Grey Tinted Low E Tempered

Glass consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.

2.4.1.5.47 1 inch (25.4 mm) Insulated Clear Glass consisting of two panes of 1/8 inch (3.2 mm) DSB insulated glass.

2.4.1.5.48 1 inch (25.4 mm) Insulated Clear Tempered Glass consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.

2.4.1.5.49 1 inch (25.4 mm) Insulated Low E DSB Glass consisting of two panes of 1/8 inch (3.2 mm) DSB insulated glass.

2.4.1.5.50 1 inch (25.4 mm) Insulated Low E Tempered Glass consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.

2.4.1.5.51 1 inch (25.4 mm) Insulated Satin Tempered Glass. Two panes of 1/8 inch (3.2 mm) Tempered insulated glass.

2.4.1.5.52 1 inch (25.4 mm) Insulated Clear Glass with Breather Tube consisting of two panes of 1/8 inch (3.2 mm) DSB insulated glass.

2.4.1.5.53 1 inch (25.4 mm) Insulated Clear Tempered Glass with Breather Tube consisting of two panes of 1/8 inch (3.2 mm) Tempered insulated glass.





adequate sealing of door to jamb or weatherseal.2.4.1.7.2 Configuration Type: Normal Headroom.

08 36 16 -28

2.4.1.7.3 Configuration Type: Low Headroom.2.4.1.7.4 Configuration Type: Vertical Lift.2.4.1.7.5 Configuration Type: Lift-Clearance.2.4.1.7.6 Configuration Type: Incline.2.4.1.7.7 Configuration Type: Contour.2.4.1.7.8 Track Size: 2 inches (51 mm).





















08 36 16 -29

2.4.1.10 AlumaView Limited Warranty: Raynor warrants the door sections against defects in material and workmanship for five years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for three years from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.










2.4.2.1.3.1 Type: Jackshaft.2.4.2.1.3.2 Type: Jackshaft with manual chain hoist.

08 36 16 -30

2.4.2.1.3.3 Type: Trolley.2.4.2.1.3.4 Motor Horsepower Rating: Intermittent 1/2 HP.2.4.2.1.3.5 Electrical Requirements: 115 volt single phase.2.4.2.1.3.6 Duty Cycle: 14 cycles/hour.2.4.2.1.3.7 Control Wiring: Solid state circuitry with provisions for connection



2.5 COMMERCIAL SECTIONAL RAISED PANEL DOOR

2.5.1 Commercial Aspen as manufactured by Raynor Garage Doors:2.5.1.1 Doors:




2.5.1.2 Sections:2.5.1.2.1 Commercial Aspen AP200C:

2.5.1.2.1.1 Sections shall be pressure bonded to injected polyurethane foam insulated core with interior and exterior skins separated by continuous thermal break. Hinge reinforcement plates shall be 19 gauge edge plates and 19 gauge center plates, located within section interior at every hinge location. End stiles to be 20 gauge galvanized steel for 18 inch and 21 inch section heights and 16 gauge for 24 inch section heights. Sections shall feature a tongue-and-groove joint for weather-tight closure between sections.

2.5.1.2.1.2 Material: Steel sandwich construction, 2 inches (51 mm) thick, roll formed from hot dipped galvanized (G40) steel complying with ASTM A 653. Exterior skin to be constructed of 26 gauge steel and interior skin to be constructed of 27 gauge steel. Exterior skin shall be woodgrain textured and interior skin shall be stucco textured. Exterior surface of sections shall feature embossed Colonial Raised Panels, Ranch Raised Panels, Recessed Grooved Colonial Panels, Recessed Grooved Ranch Panels, Plank or Flush Woodgrain Surface.


2.5.1.2.1.3.1 Color: White polyester paint.2.5.1.2.1.3.2 Color: Almond polyester paint.2.5.1.2.1.3.3 Color: Brown polyester paint.2.5.1.2.1.3.4 Color: Desert Tan polyester paint.2.5.1.2.1.3.5 Color: BronzeTone polyester paint.2.5.1.2.1.3.6 Color: Charcoal Kynar + Cool Chemistry paint.2.5.1.2.1.3.7 Color: Sandstone polyester paint.2.5.1.2.1.3.8 Color: Black Kynar + Cool Chemistry paint.2.5.1.2.1.3.9 Color: Slate polyester paint.

08 36 16 -31

2.5.1.2.1.3.10 Color: Walnut Woodgrain polyester paint.2.5.1.2.1.3.11 Color: Auburn Woodgrain polyester paint.2.5.1.2.1.3.12 Color: Mocha Woodgrain polyester paint.2.5.1.2.1.3.13 Color: Driftwood Woodgrain polyester paint.2.5.1.2.1.3.14 Color: ________.2.5.1.2.1.3.15 Color: As detailed on the Drawings.2.5.1.2.1.3.16 Color: As determined by Architect from Raynor's


2.5.1.2.1.4 Insulation: Injected polyurethane with R-value of 18.0.2.5.1.2.2 Commercial Aspen AP138C:

2.5.1.2.2.1 Sections shall be pressure bonded to injected polyurethane foam insulated core with interior and exterior skins separated by continuous thermal break. Hinge reinforcement plates shall be 19 gauge edge plates and 19 gauge center plates, located within section interior at every hinge location. End stiles to be 20 gauge galvanized steel for 18 inch and 21 inch section heights and 16 gauge for 24 inch section heights. Sections shall feature a tongue-and-groove joint for weather-tight closure between sections.

2.5.1.2.2.2 Material: Steel sandwich construction, 1-3/8 inches (35 mm) thick, roll formed from hot dipped galvanized steel complying with ASTM A 653. Exterior skin to be constructed of 26 gauge steel and interior skin to be constructed of 27 gauge steel. Exterior skin shall be woodgrain textured and interior skin shall be stucco textured. Exterior surface of sections shall feature embossed Colonial Raised Panels, Ranch Raised Panels, Recessed Grooved Colonial Panels, Recessed Grooved Ranch Panels, Plank or Flush Woodgrain Surface.


2.5.1.2.2.3.1 Color: White polyester paint.2.5.1.2.2.3.2 Color: Almond polyester paint.2.5.1.2.2.3.3 Color: Brown polyester paint.2.5.1.2.2.3.4 Color: Desert Tan polyester paint.2.5.1.2.2.3.5 Color: BronzeTone polyester paint.2.5.1.2.2.3.6 Color: Black Kynar + Cool Chemistry paint.2.5.1.2.2.3.7 Color: Charcoal Kynar + Cool Chemistry paint.2.5.1.2.2.3.8 Color: Sandstone polyester paint.2.5.1.2.2.3.9 Color: Slate polyester paint.2.5.1.2.2.3.10 Color: Walnut Woodgrain polyester paint.2.5.1.2.2.3.11 Color: Auburn Woodgrain polyester paint.2.5.1.2.2.3.12 Color: Mocha Woodgrain polyester paint.2.5.1.2.2.3.13 Color: Driftwood Woodgrain polyester paint.

2.5.1.2.2.4 Insulation: Injected polyurethane with R-value of 13.0.2.5.1.2.3 Seals: Bottom of door to have flexible U-shaped vinyl seal retained in

aluminum rail. Optional blade seal on top section to prevent airflow above header



window encased in an injection molded polypropylene frame.2.5.1.3.2 Ranch style 41 inches by 13 inches (1041 mm by 330 mm) window

minimum encased in an injection molded polypropylene frame.2.5.1.4 Glazing: Windows to be provided with glazing units as follows:

2.5.1.4.1 Single glass consisting of one pane of 1/8 inch (3.2 mm) thick DSB glass.

08 36 16 -32

2.5.1.4.2 Insulated glass consisting of two panes of 1/8 inch (3.2 mm) thick glass.2.5.1.5 Mounting: Sections mounted in door opening using:



















hardened steel ball bearings.

08 36 16 -33

2.5.1.8.3 Track Rollers: 3 inches (76.2 mm) diameter consistent with track size, with hardened steel ball bearings.

2.5.1.8.4 Perimeter Seal: Provide complete weather stripping system to reduce air infiltration. Weather stripping shall be replaceable.

2.5.1.8.4.1 For bracket mounted doors provide climate seal or vinyl seal with aluminum retainer.

2.5.1.8.4.2 For angle mounted doors provide angle clip-on seal.2.5.1.8.5 Furnish door system with locks: Exterior lock with five-pin tumbler cylinder,

night latch and steel bar engaging track.2.5.1.8.6 Furnish door system with locks: Interior lock with dead bolt provided with

hole to receive padlock provided by Owner.2.5.1.9 Commercial Aspen Limited Warranty: Raynor warrants the door sections

against defects in material and workmanship, and deterioration due to rust-through for ten years from date of delivery to the original purchaser. Raynor also warrants the door sections against delamination of the insulation from the steel skins for ten years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.

2.5.2 StyleForm (Commercial ShowCase) as manufactured by Raynor Garage Doors:2.5.2.1 Doors:




2.5.2.2 Sections:2.5.2.2.1 StyleForm Optima (Commercial ShowCase):

2.5.2.2.1.1 Sections shall be pressure bonded to a 1-7/8 inches (48 mm) thick expanded polystyrene foam core with interior and exterior skins separated by continuous thermal break. Hinge reinforcement plates shall be 16 gauge edge plates and 16 gauge center plates, located within section interior at every hinge location. End stiles to be 18 gauge galvanized steel.

2.5.2.2.1.2 Material: Steel sandwich construction, 2 inches (51 mm) thick, roll formed from draw quality, hot dipped galvanized steel complying with ASTM A 653. Exterior and interior skin to be constructed of 26 gauge steel embossed woodgrain texture. Exterior surface of sections shall feature embossed Colonial Raised Panels, Ranch Raised Panels or Flush Woodgrain Surface.


2.5.2.2.1.3.1 Color: White polyester paint.2.5.2.2.1.3.2 Color: Almond polyester paint.2.5.2.2.1.3.3 Color: BronzeTone polyester paint.2.5.2.2.1.3.4 Color: ClayTone polyester paint.2.5.2.2.1.3.5 Color: Dark Brown Kynar paint.

08 36 16 -34

2.5.2.2.1.3.6 Color: Frost White Kynar paint.2.5.2.2.1.3.7 Color: Beige Kynar paint.2.5.2.2.1.3.8 Color: Sepia Brown Kynar paint.2.5.2.2.1.3.9 Color: Desert Tan polyester paint.2.5.2.2.1.3.10 ArmorBrite Powdercoat finish, color as selected by

Architect.2.5.2.2.1.4 Insulation: Expanded polystyrene with R-value of 10.25




window encased in an extruded PVC frame.2.5.2.3.2 Ranch style 40 inches by 12 inches (1016 mm by 305 mm) window

minimum encased in an extruded PVC frame.2.5.2.4 Glazing: Windows to be provided with glazing units as follows:

2.5.2.4.1 Single glass consisting of one pane of 1/8 inch (3.2 mm) thick DSB glass.2.5.2.4.2 Insulated glass consisting of two panes of 1/8 inch (3.2 mm) thick DSB

glass.2.5.2.5 Mounting: Sections mounted in door opening using:












2.5.2.6.9.1.2 Mounting: Floor-to-shaft angles. Continuous angles

08 36 16 -35

from floor, past header, up to door shaft. Angle Size: 3-1/2 x 5 x 3/32 inches (89 x 127 x 2.5 mm) on 3-inch track.













2.5.2.9 StyleForm (Commercial ShowCase) Limited Warranty: Raynor warrants the door sections against defects in material and workmanship, and deterioration due to rust-through for ten years from date of delivery to the original purchaser. Raynor also warrants the door sections against delamination of the insulation from the steel skins for ten years from date of delivery to the original purchaser. Window components are warranted against defects in material and workmanship for one year from date of delivery to the original purchaser. Raynor warrants all hardware and spring components against defects in material and workmanship for one year (or cycle life of the springs) from date of delivery to the original purchaser. Additional Limited Warranty requirements in accordance with manufacturer's full standard limited warranty documentation.


2.5.3.1.1 Raynor ControlHoist COH, COT:2.5.3.1.1.1 Type: Jackshaft with manual chain hoist.2.5.3.1.1.2 Type: Trolley.2.5.3.1.1.3 Motor Horsepower Rating: Continuous 1/2 HP.2.5.3.1.1.4 Motor Horsepower Rating: Continuous 3/4 HP.2.5.3.1.1.5 Motor Horsepower Rating: Continuous 1 HP.2.5.3.1.1.6 Motor Horsepower Rating: Continuous 1-1/2 HP.2.5.3.1.1.7 Motor Horsepower Rating: Continuous 2 HP.2.5.3.1.1.8 Electrical Requirements: 115 volt single phase.2.5.3.1.1.9 Electrical Requirements: 230 volt single phase.2.5.3.1.1.10 Electrical Requirements: 208-230 volt three phase.

08 36 16 -36

2.5.3.1.1.11 Electrical Requirements: 460 volt three phase.2.5.3.1.1.12 Duty Cycle: 30 cycles/hour or 300 cycles/day.2.5.3.1.1.13 Control Wiring: Solid state circuitry with provisions for connection








2.5.3.1.3.1 Type: Jackshaft.2.5.3.1.3.2 Type: Jackshaft with manual chain hoist.2.5.3.1.3.3 Type: Trolley.2.5.3.1.3.4 Motor Horsepower Rating: Intermittent 1/2 HP.2.5.3.1.3.5 Electrical Requirements: 115 volt single phase.2.5.3.1.3.6 Duty Cycle: 14 cycles/hour.2.5.3.1.3.7 Control Wiring: Solid state circuitry with provisions for connection



3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly prepared. Verify that site conditions are acceptable for installation of doors, operators, controls and accessories. Ensure that openings are square, flush and plumb.

3.1.2 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

08 36 16 -37

3.2.1 Clean surfaces thoroughly prior to installation.

3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

3.3.1 General: Install door, track and operating equipment complete with all necessary accessories and hardware according to shop drawings, manufacturer's instructions.

3.3.2 Lubricate bearings and sliding parts, and adjust doors for proper operation, balance, clearance and similar requirements.

3.4 PROTECTION

3.4.1 Clean installed products in accordance with manufacturer's instructions prior to Owner's acceptance. Remove and legally dispose of construction debris from project site.

3.4.2 Remove temporary coverings and protection of adjacent work areas. Repair or replace installed products damaged prior to or during installation.

3.4.3 Lubricate bearings and sliding parts, assure weather tight fit around door perimeter and adjust doors for proper operation, balance, clearance and similar requirements. Protect installed products until completion of project.

3.4.4 Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

08 36 16 -38

Documents

· Web viewWindows: Provide door sections with windows in lieu of 0.050 inch (1.3mm) aluminum filler panels. Locations to comply with door elevation drawings. ** NOTE TO SPECIFIER