Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
ApplicationUniversal general purpose lithium grease for lubrication of rolling and slide bearings as well as other
frictionpairs operating in low loads used in agriculture and various branches of industry. It is dedicated to low
loadsand elevated temperatures. The product is characterized by high thermal and mechanical stability andguarantees invariability of consistence during operation. The grease provides good protection against
corrosion and is resistant to washout.Specification
DIN 51502: K2K-30; ISO: L-XCCEA2-30°-120°C
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
2
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
MINERAL OIL APPLICATION TECHNOLOGY
TECHMOLITH 2
Technische Daten:
Chem. und Physik. Kennda-
ten Einheit Prüfverfahren Techmolith 2
NLGI-Class - DIN 51 818 2
Walk penetration 1/10 mm DIN ISO 2137 265 bis 295
Thickener - - Lithium
Drop-Point °C DIN ISO 2176 ca. 180
Operating temperature range
(permanent lubrication°C -
k-30 bis +120
short time + 130
Base oil viscosity at 40 ° C mm²/s DIN 51 562 ca. 110
VKA welding force N DIN 51350-4 2000
Behavior towards Water - DIN 51 807/1 1 - 90
Corossion protectionKorr. -
Grad DIN 51802 0
3
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
4
HIGH EFFICIENCY GREASE WITH GOOD FLOW CAPACITYTechmol PLEX-20200/2 is a calcium complex soap thickened mineral greases with high resistance tooxidation. Contains antioxidant additives package to secure high efficiency under high temperatures.Provided with superior flow characteristics they can be used in single or double line centralized lubricatingsystems.Thanks to a specific formulation, they can stand long service periods without decomposition nor buildingdeposits.Do not attack ferrous or non-ferrous metals at high temperatures.Techmol PLEX-20200/2 is intended for any mechanism under high temperatures in any segment of the industry,mainly in the steel, rubber, cement industry etc.
Techmol PLEX-20200/2 can be considered multifunctionhigh efficiency greases.
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
5
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Techn
Techmol PLEX-20200/2
HIGH EFFICIENCY GREASE WITH GOOD FLOW CAPACITY
DESCRIPTION AND APPLICATIONS Techmol PLEX-20200/2 is a calcium complex soap thickened mineral greases with high resistance to oxidation. Contains antioxidant additives package to secure high efficiency under high temperatures. Provided with superior flow characteristics they can be used in single or double line centralized lubricating systems. Thanks to a specific formulation, they can stand long service periods without decomposition nor building deposits. Do not attack ferrous or non-ferrous metals at high temperatures. Techmol PLEX-20200/2 is intended for any mechanism under high temperatures in any segment of the industry, mainly in the steel, rubber, cement industry etc. Techmol PLEX-20200/2 can be considered
multifunction high efficiency greases.
PROPERTIES Anti-wear and EP properties. Washing by water resistance. No change in the lubricating properties in presence of
water. Structural and chemical stability. Antioxidant and antirust capacity. Very good flow characteristics. Wide service temperatures range.
CAUTIONS The usual ones when handling and using lubricants. Avoid excess of grease as well as too frequent
relubrication cycles. Keep the can closed to avoid contamination. Do not mix with different nature greases.
PHYSICAL-CHEMICAL CHARACTERISTICS
Colour Brown
Thickener, soap type Calcium Complex
Base oil Mineral
NLGI Consistency class Grade 2
Penetration at 25ºC, (0,1mm) 265 – 295
Worked penetration 105 W, (0,1mm) Max. +80
Drop point, (ºC) Min. 250
4 ball test Welding load, (kg)
Scar diameter 1’/80kg, (mm)
Min. 350 Max. 0,65
EMCOR Corrosion test Max. 1
Copper strip corrosion test, 24h/100ºC Max. 1b
Resistance to water washout at 80ºC, (%) Max. 2
Oxidation stability, 100h/100ºC, (kg/cm2) Max. 0,6
Service temperature, (ºC) -25 to 150
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Multi-purpose lithium grease intended for lubricating bearings, pins, and joints as well as other
elements in harsh operating conditions - increased pressure and temperature, as well as with
irregular and high loads. The product can be used for lubricating highly loaded friction objects
in a wide range of industrial applications, where a lubricant with high anti-seize properties is
required. It is characterized by high mechanical stability, anticorrosion protection in the
presence of water and good resistance to oxidation. :
Grease DIN 51 825 – KP 2 K-30 nach DIN 51 502 ISO-L-XCCHB2 gem. -30 to +120°C short time +130°C
6
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
7
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Techmolith EP2
NLGI-Class - DIN 51 818 2
Walk penetration 1/10 mm PN-ISO
2137:2011281
thickener - - Lithium
Melt Point °C DIN ISO 2176 ca. 209
Operating temperature range
(Permanent lubrication)°C -
k-30 bis +120
short time + 130
Base oil viscosity at 40 ° C mm²/s DIN 51 562 ca. 130
VKA welding force N DIN 51350-4 2450
Corrosion protection / copper degree
of
corrosion
PN-EN ISO
2160:20041
A multi-purpose lithium-calcium grease intended for the lubrication of highly
loaded rolling, slide, ball and roller bearings and other friction objects, where
difficult working conditions occur: water availability, impact loads, high dustiness.
Contrary to conventional lithium lubricants, the product is particularly resistant
to water washout. The grease is produced on the basis of lithium-calcium soap,
highly refined base oil and a package of enriching additives. It is characterizedby very good resistance to water washout and high mechanical stability
QualificationGrease KP2K-30 nach DIN 51 502 ISO-L-XCCHB2
You can take it for: Rolling bearings Slide bearings Gears Joint and bolts Central lubrication system
Mineral oil Application technologyTechmolith EP2
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Multi-purpose lithium grease intended for lubricating bearings, pins, and joints as well as other elements in harsh operating conditions - increased pressure and temperature, as well as with irregular and high loads.
The product can be used for lubricating highly loaded friction objects in a wide range of industrial applications, where a lubricant with high anti-seize properties is required. It is characterized by high
mechanical stability, anticorrosion protection in the presence of water and good resistance to oxidation. :
Grease DIN 51 825 – KP 2 K-30 nach DIN 51 502 ISO-L-XCCHB2 gem. -30 to +120°C short time +130°CColour: blue
8
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
9
Mineral oil Application technologyTechmolith blue EP2
A multi-purpose lithium-calcium grease intended for the lubrication of highly
loaded rolling, slide, ball and roller bearings and other friction objects, where
difficult working conditions occur: water availability, impact loads, high dustiness.
Contrary to conventional lithium lubricants, the product is particularly resistant
to water washout. The grease is produced on the basis of lithium-calcium soap,
highly refined base oil and a package of enriching additives. It is characterizedby very good resistance to water washout and high mechanical stability
Qualification
Grease KP2K-30 nach DIN 51 502 ISO-L-XCCHB2
You can take it for: Rolling bearings Slide bearings Gears Joint and bolts Central lubrication system
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Techmolith blue EP2
NLGI-Class - DIN 51 818 2
Walk penetration 1/10 mm PN-ISO
2137:2011281
thickener - - Lithium
Melt Poin °C DIN ISO 2176 ca. 209
Operating temperature range
(Permanent lubrication)°C -
k-30 bis +120
short time + 130
Base oil viscosity at 40 ° C mm²/s DIN 51 562 ca. 130
VKA welding force N DIN 51350-4 2450
Corrosion protection / copper degree
of
corrosion
PN-EN ISO
2160:20041
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Techmol Transblue
Complex lithium grease with increased durability intended for friction
elements operating in extremely hard conditions of various industries,
in particular for lubrication of axle bearings in vehicles of commercial truck
transport. The lubricant contains a special formula of additives that provide
extraordinary anti-wear, lubricating and anticorrosion properties. The grease
is characterized by very high adhesion to the lubricated surface and very
good resistance to water washout. The product is characterized by high
mechanical stability and invariability of consistence during extended operation.:DIN 51502: KP2P-30; ISO: L-XCEHB2
Working Temperatur -30°-160°C
10
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
11
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Complex lithium grease with increased durability intended for friction elements operating in
extremely hard conditions of various industries, in particular for lubrication of axle bearings in
vehicles of commercial truck transport. The lubricant contains a special formula of additives that
provide extraordinary anti-wear, lubricating and anticorrosion properties. The grease is
characterized by very high adhesion to the lubricated surface and very good resistance to water
washout. The product is characterized by high mechanical stability and invariability of
consistence during extended operation.
DIN 51502: KP2P-30; ISO: L-XCEHB2
Working Temperatur -30°-160°C
You can take it for: Rolling bearings Slide bearings Gears
Mineral oil Application technologyTransblue
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Transblue
NLGI-Class - DIN 51 818 2
Walk penetration 1/10 mm PN-ISO
2137:2011281
thickener - - Lithium
Melt Poin °C DIN ISO 2176 ca. 266
Operating temperature range
(Permanent lubrication)°C -
k-30 bis +120
short time + 130
Base oil viscosity at 40 ° C mm²/s DIN 51 562 ca. 220
VKA welding force N DIN 51350-4 23923
Corrosion protection / copper degree
of
corrosion
PN-EN ISO
2160:20041
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
12
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
MULTIPURPOSE SPECIALITY GREASE FOR EXTREME OPERATING TEMPERATURES
Special grease with an inorganic soap thickenedand synthetic oil, intended for extreme temperatures.
PROPERTIES
- Resists very low temperatures (to -55ºC).
- Makes cold start-up easier. - Good behaviour to high temperatures (to 180ºC). - Wide operating temperatures range.
- High antirust capacity.
- Resists medium loads. - Good anti-wear capacity. - High mechanical stability. - Does not harden.
Meets MIL-PRF-81322 G.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
13
Industrial Lubricants
Techmol ARMIGRAS BT-2
MULTIPURPOSE SPECIALITY GREASE FOR EXTREME OPERATING TEMPERATURES
DESCRIPTION Special grease with an inorganic soap thickened and synthetic oil, intended for extreme temperatures. APPLICATIONS Bearings under strong temperature variations: From start-up at very low temperatures till high service temperatures (-55 to 180ºC.). Multipurpose bearing grease in a wide operating temperatures range and medium or high speed.
PROPERTIES - Resists very low temperatures (to -55ºC). - Makes cold start-up easier. - Good behaviour to high temperatures (to 180ºC). - Wide operating temperatures range. - High antirust capacity.
- Resists medium loads. - Good anti-wear capacity. - High mechanical stability. - Does not harden.
CAUTIONS - The usual ones when handling and using lubricants. - Avoid grease excess as well as too frequent lubrication
periods. - Keep the can closed to avoid contamination. - Do not mix with different nature greases.
PHYSICAL - CHEMICAL CHARACTERISTICS
Colour Brown
Thickener Inorganic
Base oil Synthetic
NLGI Consistency class Grade 2
Worked penetration 60W, (0,1mm) 265 – 295
Worked penetration 105 W, (0,1mm) Max. 350
Drop point, (ºC) Nil
4-balls SHELL device - Load-Wear index, (kg) - Wear scare diameter, 1h/40kg, (mm)
Meets MIL-PRF-81322 G.
WAY TO USE Application manual or proper greaser.
Min. 30 Max. 0,65
Copper corrosion, 24h/100ºC Max. 1b
Oxidation stability, 100h/100ºC, (kg/cm) Max. -0,3
Evaporation weight loss, 22h/177ºC, (%) Max. 10
Oil separation, 30h/177ºC, (%) Max. 8
Water washout, 40ºC, (%) Max. 10
Operating temperature, (ºC) -55 to 180
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Description Lubricating grease based on a lithium soap, with highly ef- fective additive packages, EP additives and a solid lubricant. Properties Resistant to aging, with good corrosion and wear protection and EP additives. The solid lubricant ensures very good emergency running properties, especially in the case of loss lubrication. Temperature range –30 °C to +130 °C
14
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
15
Product information
Techmol MOS2
Description Lubricating grease based on a lithium soap, with highly ef-
fective additive packages, EP additives and a solid lubricant.
Properties Resistant to aging, with good corrosion and wear protection and
EP additives. The solid lubricant ensures very good emergency running properties, especially in the case of loss
lubrication. Temperature range –
30 °C to +130 °C
Characteristic data Brief description KPF2K-30
DIN 51502
NLGI number 2
DIN 51811
Worked penetration 265-295 1/10 mm
DIN ISO 2137
Dropping point >180 °C DIN ISO 2176
Oil separation after 7 days at 40 °C
2,8 % DIN 51817
Flow pressure at -30 °C
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Description Multi-purpose grease based on a lithium soap, with solid lubricant. Properties Resistant to aging, with good corrosion and wear protection. The solid lubricant ensures very good emergency running properties, especially in the case of insufficient lubrication. Temperature range –30 °C to +120 °C short periods up to +130 °C
16
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
17
Product information
Techmol Grafol L2F100 Grease
Description Multi-purpose grease based on a lithium soap, with solid lubricant. Properties Resistant to aging, with good corrosion and wear protection. The
solid lubricant ensures very good emergency running properties, especially in the case of insufficient lubrication. Temperature range –30 °C to +120 °C short periods up to +130 °C
Characteristic data Brief description KF2K-30
DIN 51502
NLGI number 2
DIN 51818
Worked penetration 265-295 1/10 mm
DIN ISO 2137
Dropping point >180 °C DIN ISO 2176
Oil separation after 7 days at 40 °C
2,2 % DIN 51817
Flow pressure at -30 °C
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Multi-purpose assembly paste based on fine-particle copper, designedfor lubrication and protection of components in extremely high temperatures.
The grease creates a durable sealing layer that protects against corrosionand abrasion as well as water washout. It allows for easy assembly and subsequent
dismantling of components without damage. It is suitable for the lubricationof bolts and nuts, thread connections, spark plugs, pins and bolts. The product
eliminates squeaking and creaking. Do not use it on aluminum components.
18
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
19
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Mineral oil application echnologyCopper Paste
Grease DIN 51 825 – K 2 K-30 nach DIN 51 502
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Copper Paste
NLGI-Class - DIN 51 818 2
Water content DIN51777/1
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
High temperature paste based on aluminum, graphite and copper intended for the lubrication of demolition mouldings of hydraulic and pneumatic hammers. The product is not suitable for the
lubrication of bearings. It can be used as a paste protecting against burning and corrosion, creating a durable separating layer. The grease is resistant to extreme pressure and water washout. Solid additives
increase the possibility of transferring large impact loads and guarantee the maintenance of a lubricating film at extreme loads. The product is characterized by good anti-corrosion protection and
resistance to aging. .
Working field -20 bis +1100 °C
20
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
21
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Mineral oil application echnologyTECHMOL Meißelpaste
High temperature paste based on aluminum, graphite and copper intended for the lubrication of demolition mouldings of hydraulic and pneumatic hammers. The product is not suitable for the
lubrication of bearings. It can be used as a paste protecting against burning and corrosion, creating a durable separating layer. The grease is resistant to extreme pressure and water washout. Solid additives
increase the possibility of transferring large impact loads and guarantee the maintenance of a lubricating film at extreme loads. The product is characterized by good anti-corrosion protection and
resistance to aging. .
Working field -20 bis +1100 °C
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Meißel Paste
NLGI-Class - DIN 51 818 2
Water content DIN51807 0-9
Base oil viscosity at 40 ° C -
mm²/s
DIN 51 562
-Ca. 350
Colour Brown/black
Operating temperature range
(Permanent lubrication)°C - -20-1100°C
VKA welding force N DIN 51350-4 500
Corrosion protection degree
of
corrosion
DIN 51802 0
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Description Special grease which is compatible with plastics and is formulated for the maintenance and care of vehicle electronic systems, particularly the battery terminals and electrical connectors. Ensures
reliable starting and a longer battery life. Offers high corrosion protection and prevents leakage currents. Prevents the contact resistance from increasing during operation and ensures lower loss than with untreated contacts. Properties - prevents leakage currents prevents the contact resistance from increasing during operation and ensures lower loss than with untreated contacts - - good corrosion
protection - very compatible with plastics - good electronic properties
22
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
23
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Description Special grease which is compatible with plastics and is formulated for the
maintenance and care of vehicle electronic systems, particularly the battery terminals
and electrical connectors. Ensures reliable starting and a longer battery life. Offers
high corrosion protection and prevents leakage currents. Prevents the contact
resistance from increasing during operation and ensures lower loss than with
untreated contacts. Properties - prevents leakage currents prevents the contact
resistance from increasing during operation and ensures lower loss than with
untreated contacts - - good corrosion protection - very compatible with plastics - good
electronic properties
DIN 51 825 K 2 C-40 / -40°C bis +60°C
Mineral oil application echnologyTECHMOL Batterie Clamp Grease
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Batterie Clamp Grease
NLGI-Class - DIN 51 818 2
Water content DIN51807 0/09
Base oil viscosity at 40 ° C -
mm²/s
DIN 51 562
-Ca. 360
Colour Brown
Operating temperature range
(Permanent lubrication)°C - -40- + 60°C
Thickner Calcium soap
Corrosion protection degree
of
corrosion
DIN 51802 0/0
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
24
Available after consultationin the following Containers:
20g Tube50g Tube
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
25
Industrial Lubricants
Techmol ZKF M–2
Technical Information
DESCRIPTION Long life organic soap thickened greases with highly refined mineral oil and additive package, which provide them with superior anti-wear, EP properties and high antioxidant and anticorrosive capacity. These are excellent greases for the lubrication of bearings and mechanisms exposed to the combined action of high temperatures, heavy loads and water.
APPLICATIONS Techmol ZKF M–2 grease is intended for the lubrication of mechanisms in severe operating conditions, such as the lubrication of steel continuous casting where following ambient must be faced
Poor variation of the consistency to temperatures increase.
Very good behaviour to water and water wash-out. Long duration. It does not drip nor it slips. Ample
periods between applications. Smaller consumption. Economical.
Excellent sealing capacity, which prevents the contamination with particles.
Very good pumpability in a wide temperatures range. Long life lubricating greases. Outstanding quality-price relation. Fine film, reduces the adhesion of abrasive matter,
facilitates the inspection and control of the state of the wire.
High service temperature. High Ferro static pressures. Big quantity of cooling water. High contamination with metallic oxides, hard
particles, metal foils, etc. Long centralized systems.
PROPERTIES Superior behaviour and stability to temperature. High mechanic work stability.
PHYSICAL – CHEMICAL CHARACTERISTICS
Colour Light brown
Thickener, soap type Urea compound
Base oil nature Mineral
NLGI Consistency class Grade 2 Worked penetration 60 W, (0,1mm) 265 – 295
Worked penetration 105 W, (0,1mm) Max. 350
Drop point, (ºC) 250
EMCOR corrosion test distilled water salt water
Min. 300 Max. 0,50
Oil separation, % Max. 6
Water washout, 80ºC, (%) Max. 2
Oxidation stability, (bar) Max. 0,5
Copper corrosion 100ºC Max. 1 b
Operating temperature, (ºC) -20 to 150
Techmol ZKF M–2 grease do no bear any metallic soap so the resistance to oxidation and aging is much increased when compared with the conventional greases formulated with complex or simple soap which are being used in such
kind of operations.
CAUTIONS The usual ones when handling and using lubricants. Keep the can closed to avoid contamination. Do not mix with different nature greases. There is available the MSDS of the product, according
to the effective European normative.
0 Max. 2
4-ball-test Welding load, (kg) wear scar diameter 1h/40 kg, (mm)
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
26
Available after consultationin the following Containers:
20g Tube50g Tube
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
27
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Techmol ZKF ELG–38
Technical Information
DESCRIPTION Inorganic thickened grease, based on high quality mineral oils containing high percentage of conducting solids to obtain excellent results in the field of application at electric contacts.
CAUTIONS
The usual ones when handling and using lubricating products.
Do not mix with different nature greases. Keep the can closed to avoid contamination.
PHYSICAL - CHEMICAL CHARACTERISTICS
Thickener Inorganic
Base oil nature Mineral
Colour Clear yellow
NLGI consistency class Grade 2 – 3
Penetration at 25ºC, (0,1mm) 250 – 280
Worked penetration 60 W at 25ºC, (0,1mm) 250 – 290
Drop point, (ºC) >300
Water resistance, 3h/90ºC Max. Grade 1
EMCOR test corrosion Max. Grade 1
Density at 25ºC, (g/cm3) 1,15 – 1,20
Service temperatures, (ºC) -20 to 140
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
28
Available after consultationin the following Containers:
20g Tube50g Tube100g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal
Special sizes available on request
Ceramic mounting paste resistant to extreme temperatures dedicated to applications in the
automotive industry and demanding industries. The product is recommended for assembly of
braking systems with ABS and ESP systems. It creates a protective layer preventing the
brazing of screws and metal connections made of steel, precious alloys, copper and
aluminum. The paste protects against corrosion as well as aggressive and atmospheric
factors. It reduces friction and wear of lubricated parts. The product contains adhesion
additives that increase adhesion to the surface and resistance to water washout.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
29
Mineral oil application echnologyTECHMOL Ceramic Paste
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Ceramic Paste
NLGI-Class - DIN 51 818 2
Water content 90°C DIN51807 Max 1
Base oil viscosity at 40 ° C -
mm²/s
DIN 51 562
-Ca. 500
Colour white
Operating temperature range
(Permanent lubrication)°C - -30- + 1400°C
Thickner Betonit
Troppoint no
Corrosion Copper protection degree
of
corrosion
PN-EN ISO
3104-20041
Ceramic mounting paste resistant to extreme temperatures dedicated to applications in the
automotive industry and demanding industries. The product is recommended for assembly of
braking systems with ABS and ESP systems. It creates a protective layer preventing the
brazing of screws and metal connections made of steel, precious alloys, copper and
aluminum. The paste protects against corrosion as well as aggressive and atmospheric
factors. It reduces friction and wear of lubricated parts. The product contains adhesion
additives that increase adhesion to the surface and resistance to water washout.
DIN 51502: KPF2U-30; ISO: L-XCGHB2
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
30
Ceramic mounting paste resistant to extreme temperatures dedicated to applications in the
automotive industry and demanding industries. The product is recommended for assembly
of braking systems with ABS and ESP systems. It creates a protective layer preventing the
brazing of screws and metal connections made of steel, precious alloys, copper and
aluminum. The paste protects against corrosion as well as aggressive and atmospheric
factors. It reduces friction and wear of lubricated parts. The product contains adhesion
additives that increase adhesion to the surface and resistance to water washout.
Available after consultationin the following Containers:
20g Tube50g Tube100g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
31
Mineral oil application echnologyTECHMOL Ceramic Paste
Techicel Data:
Chem. And Physics.
CharacteristicsUnit Test procedure Wheel hub Paste
NLGI-Class - DIN 51 818 2
Water content 90°C DIN51807 Max 1
Base oil viscosity at 40 ° C -
mm²/s
DIN 51 562
-Ca. 500
Colour white
Operating temperature range
(Permanent lubrication)°C - -30- + 1400°C
Thickner Betonit
Troppoint no
Corrosion Copper protection degree
of
corrosion
PN-EN ISO
3104-20041
Ceramic mounting paste resistant to extreme temperatures dedicated to applications in the
automotive industry and demanding industries. The product is recommended for assembly of
braking systems with ABS and ESP systems. It creates a protective layer preventing the
brazing of screws and metal connections made of steel, precious alloys, copper and
aluminum. The paste protects against corrosion as well as aggressive and atmospheric
factors. It reduces friction and wear of lubricated parts. The product contains adhesion
additives that increase adhesion to the surface and resistance to water washout.
DIN 51502: KPF2U-30; ISO: L-XCGHB2
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Brake assembly PasteDOT 3, DOT 4 und DOT 5.1 compatibel.
32
Available after consultationin the following Containers:
20g Tube50g Tube100g Tube
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
33
Industrial Lubricants
Technical Information
Techmol Brake assembly Paste M-2/1 STF HIGH PERFORMANCE GREASE WITH HIGH COMPATIBILITY WITH THERMO- PLASTICS AND ELASTOMERS
Specifically formulated grease with organic thickener and synthetic oil to meet the requirements of DT 3G0217 type B application standards. PTFE powder contains.
APPLICATIONS Lubricating grease designed for the lubrication of mechanisms with metal-elastomer and/or thermoplastics contacts such as ISOVAC (brake mechanisms).
Techmol KOMPLEX M2/1 STF shows superior compatibility with most of elastomers and thermoplastics to secure utmost behaviour as well as to improve the sealing of the system. COMPATIBILITY WITH THERMOPLASTICS AND ELASTOMERS :
PHYSICAL – CHEMICAL CHARACTERISTICS
Mixture compatibility with: 16 SB 11SB 10 EP 13 NB 1 CR Hardness variation, 70h/100ºC (DIN 53505) -5 to 5 points
-5 to 5 points
-5 to 5 points
Max. 15 points
Max. 15 points
Volume variation, 70h/100ºC (ASTM D 478)
-5 to 5%
-5 to 5%
-5 to 5%
Max. -15%
Max. -15%
Colour -- Ivory Base oil nature -- Synthetic Thickener -- Urea compound Worked Penetration 60W 25ºC, (0,1mm) ASTM D-217 280-320 Density at 20ºC, (gr/cc) G038.00 1 Approx. Drop point, (ºC) ASTM D-566 Min. 270 Evaporation loss 48h/150ºC, (%) G041.00 Max. 6 Evaporation loss 400h/120ºC, (%) G041.00 Max. 5,0 Oil separation 3h/120ºC, (%) FTM-791.321 Max. 2,5 Water resistance 24 h. / Room temperature 72 h. / Room temperature
--
Nil
Max. 1,5
Penetration at –40ºC, (0,1mm) ASTM D-217 Min. 175 Flow pressure at –40ºC, (mbar) DIN 51805 Max. 1200
It formulated with a synthetic oil and long life thickener to work in a wide temperatures range from –40 to 180ºC. A superior lubrication capacity is secured both in start up an in severe service conditions.
CAUTIONS The usual ones when handling and using lubricants. Keep the can closed to avoid contamination. Do not mix with different nature greases.
Clear and transparent water
Clear and transparent water DIN 51817 Clear and transparent water
Brake fluid resistance 24 h. / Room temperature
72 h. / Room temperature
Clear and transparent fluid DIN 51817 mod. Clear and transparent fluid
Corrosion 400 h/40ºC, 100% HR
Cast Steel Aluminium
Nil
Nil Low temperature torque at -40ºC (Nm)
Starting torque Running torque, 10’
ASTM D-1478 Max. 2,5
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
34
Available after consultationin the following Containers:
20g Tube50g Tube100g Tube200g Plastik can400g Plastic Can1000g Platic can
Special sizes available on request
Techmol Silicon is a food grade inorganic soap thickenedsilicone grease. It is intended for the general lubrication ofmechanisms operated under strong temperature variations,water action and chemical ambiences. It is intended mostlyfor the lubrication of taps.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
35
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Techmol Silicone Paste
PROPERTIES
- Good lubricating capacity. - Superior resistance to cold/hot water and chemical
agents. - Wide range of service temperatures. - Approved by the Czech Health Department to
lubricate mechanisms of the drinkable water treatment plants.
- Food grade. NSF H-1 class (previous USDA H-1), reg. Nber. 111111.
CAUTIONS - The usual cautions when handling and using
lubricants. - Avoid excess of grease as well as too frequent
lubrication. - Keep the can closed to avoid contamination.
- Avoid mixture with different base greases.
PHYSICO-CHEMICAL CHARACTERISTICS
□ Thickener Inorganic
□ Base oil Methyl polysiloxane
□ Colour Translucent white
□ NLGI Class Class 2 to 3
□ Penetration at 25ºC, (0.1 mm) 250-280
□ Drop point, (ºC) Min. 300
□ Resistance to water action 3hr/90ºC Degree 0 □ Density at 25ºC, (g/cm3) 0.95 – 1.0
□ Copper strip corrosion test, 24hr/100ºC 1b max.
□ Service temperature, (ºC) -50 to 180
Techmol Silicon is a food grade inorganic soap thickened silicone grease. It is intended for the general lubrication of mechanisms operated under strong temperature variations, water action and chemical ambiences. It is intended mostly for the lubrication of taps.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Weapon Grease with Mos2PROPERTIES
- High resistance to oxidation and temperature.- Excellent lubricant power.
- Very good behavior at low-temperature.- Wide range of working temperature, -73 to 130ºC.
- Meets standard MIL-G-21164D.
36
Available after consultationin the following Containers:
20g Tube50g Tube100g Tube200g Plastik can400g Plastic Can1000g Platic can
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
37
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Industrial lubricants
Technical Information
Techmol GUN Grease
HIGH PERFORMANCE SYNTHETIC GREASE
DESCRIPTION Techmol Gun Grease is a grease based on lithium soap, synthetic oil and last generation additives that give the grease high performance and long life properties. It also contains molybdenum disulphide. It has been developed for the lubrication of sliding steel parts, highly charged (splines, worm, racks, etc.) and for bearings subjected to high loads, mainly in the field of aviation.
PROPERTIES - High resistance to oxidation and temperature. - Excellent lubricant power. - Very good behavior at low-temperature. - Wide range of working temperature, -73 to 130ºC. - Meets standard MIL-G-21164D.
CAUTIONS - The usual ones when handling and using lubricants. - Keep the can closed to avoid contamination. - Do not mix with different nature greases.
PHYSICAL–CHEMICAL CHARACTERISTICS
Characteristics
Regulation
Value
Unit
Thickener - Lithium soap - Base oil - Synthetic - Colour - Black - Worked penetration 60W ASTM D-217 290 0,1 mm Worked penetration 105W ASTM D-217 300 0,1 mm Drop point ASTM D-566 175 ºC Oxidation stability, 100 h/100ºC ASTM D-942 0,35 Kg/cm2 Oxidation stability, 500 h/100ºC ASTM D-942 0,8 Kg/cm2 Cooper corrosion, 24 h / 100ºC ASTM D-4048 1 a - Torque stress @-73ºC: -Starting -Working during 1 hour
N.m N.m
Resistance water washout, 40ºC - 4 %
Oil separation, 30 h/100ºC - 4,6 Evaporation weight loss, 22 h/100ºC ASTM D-972 0,3 %
EP property (Load-wear index) - 50 Kgf
Service temperature - -73 to 130 ºC
ASTM D-1478 0,32 0,041
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
38
Available after consultationin the following Containers:
- 100ml Bottle
Special sizes available on request
S-761 is a fully synthetic multifunctional lubricating oil and is also suitable as
Preservation and cleaning fluid.
S-761 contains additives to improve the corrosion and wear protection behavior.
S-761 is ideally suited for lubrication, preservation, cleaning and care
various weapon systems.
S-671 can be by drip lubrication, automatic lubrication devices, oil can or brush
be applied.
Meets the requirements after
BWB TL 9150-0078
NATO code: S-761
Operating temperature
-40 to 150 ° C
Freeze pour point
-57 ° C
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
MINERALÖL-ANWENDUNGSTECHNIK
Techmol Gun Oil
Technische Daten:
Chem. und Physik. Kennda-
ten Einheit Prüfverfahren
MINERALÖL-ANWENDUNGSTECHNIK
Gun Oil S-761
GrundölSyntetisch
Flammpunkt °C DIN ISO 2592 > 180
Pourpoint C°DIN ISO
3016-57
Viscosität bei 40 °C mm² DIN 51562 ca. 10
Viskosität bei 100° Cmm²
DIN 51562 ca. 19
-
Beschreibung:
S-761 is a fully synthetic multifunctional lubricating oil and is also suitable as
Preservation and cleaning fluid.
S-761 contains additives to improve the corrosion and wear protection behavior.
S-761 is ideally suited for lubrication, preservation, cleaning and care
various weapon systems.
S-671 can be by drip lubrication, automatic lubrication devices, oil can or brush
be applied.
Meets the requirements after
BWB TL 9150-0078
NATO code: S-761
Operating temperature
-40 to 150 ° C
Freeze pour point
-57 ° C
39
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
40
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
Aerospace Armigras Grease with Mos2PROPERTIES
- High resistance to oxidation and temperature.- Excellent lubricant power.
- Very good behavior at low-temperature.- Wide range of working temperature, -73 to 130ºC.
- Meets standard MIL-G-21164D.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
41
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Industrial lubricants
Technical Information
Techmol Armigrease 353 Plus Grease
HIGH PERFORMANCE SYNTHETIC GREASE
DESCRIPTION Techmol Armigrease 353 Plus Grease is a grease based on lithium soap, synthetic oil and last generation additives that give the grease high performance and long life properties. It also contains molybdenum disulphide. It has been developed for the lubrication of sliding steel parts, highly charged (splines, worm, racks, etc.) and for bearings subjected to high loads, mainly in the field of aviation.
PROPERTIES - High resistance to oxidation and temperature. - Excellent lubricant power. - Very good behavior at low-temperature. - Wide range of working temperature, -73 to 130ºC. - Meets standard MIL-G-21164D.
CAUTIONS - The usual ones when handling and using lubricants. - Keep the can closed to avoid contamination. - Do not mix with different nature greases.
PHYSICAL–CHEMICAL CHARACTERISTICS
Characteristics
Regulation
Value
Unit
Thickener - Lithium soap - Base oil - Synthetic - Colour - Black - Worked penetration 60W ASTM D-217 290 0,1 mm Worked penetration 105W ASTM D-217 300 0,1 mm Drop point ASTM D-566 175 ºC Oxidation stability, 100 h/100ºC ASTM D-942 0,35 Kg/cm2 Oxidation stability, 500 h/100ºC ASTM D-942 0,8 Kg/cm2 Cooper corrosion, 24 h / 100ºC ASTM D-4048 1 a - Torque stress @-73ºC: -Starting -Working during 1 hour
N.m N.m
Resistance water washout, 40ºC - 4 %
Oil separation, 30 h/100ºC - 4,6 Evaporation weight loss, 22 h/100ºC ASTM D-972 0,3 %
EP property (Load-wear index) - 50 Kgf
Service temperature - -73 to 130 ºC
ASTM D-1478 0,32 0,041
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
42
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
MULTIPURPOSE SPECIALITY GREASE FOR EXTREME OPERATING TEMPERATURES
Special grease with an inorganic soap thickenedand synthetic oil, intended for extreme temperatures.
PROPERTIES
- Resists very low temperatures (to -55ºC).
- Makes cold start-up easier. - Good behaviour to high temperatures (to 180ºC). - Wide operating temperatures range.
- High antirust capacity.
- Resists medium loads. - Good anti-wear capacity. - High mechanical stability. - Does not harden.
Meets MIL-PRF-81322 G.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
43
Industrial Lubricants
Techmol ARMIGRAS BT-2
MULTIPURPOSE SPECIALITY GREASE FOR EXTREME OPERATING TEMPERATURES
DESCRIPTION Special grease with an inorganic soap thickened and synthetic oil, intended for extreme temperatures. APPLICATIONS Bearings under strong temperature variations: From start-up at very low temperatures till high service temperatures (-55 to 180ºC.). Multipurpose bearing grease in a wide operating temperatures range and medium or high speed.
PROPERTIES - Resists very low temperatures (to -55ºC). - Makes cold start-up easier. - Good behaviour to high temperatures (to 180ºC). - Wide operating temperatures range. - High antirust capacity.
- Resists medium loads. - Good anti-wear capacity. - High mechanical stability. - Does not harden.
CAUTIONS - The usual ones when handling and using lubricants. - Avoid grease excess as well as too frequent lubrication
periods. - Keep the can closed to avoid contamination. - Do not mix with different nature greases.
PHYSICAL - CHEMICAL CHARACTERISTICS
Colour Brown
Thickener Inorganic
Base oil Synthetic
NLGI Consistency class Grade 2
Worked penetration 60W, (0,1mm) 265 – 295
Worked penetration 105 W, (0,1mm) Max. 350
Drop point, (ºC) Nil
4-balls SHELL device - Load-Wear index, (kg) - Wear scare diameter, 1h/40kg, (mm)
Meets MIL-PRF-81322 G.
WAY TO USE Application manual or proper greaser.
Min. 30 Max. 0,65
Copper corrosion, 24h/100ºC Max. 1b
Oxidation stability, 100h/100ºC, (kg/cm) Max. -0,3
Evaporation weight loss, 22h/177ºC, (%) Max. 10
Oil separation, 30h/177ºC, (%) Max. 8
Water washout, 40ºC, (%) Max. 10
Operating temperature, (ºC) -55 to 180
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
We keep the World running
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
44
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
Techmol Boot Grease ARMIGRAS 460
HIGH PERFORMANCE SEA WATER RESISTING GREASE
DESCRIPTION Specially formulated grease based semi-synthetic oil, lithium-calcium mixed soap and special additives that provide the grease with high performance.
PROPERTIES
High adherence and sealing High corrosion protection Good load carrying capacity Work temperature: -10 to 110ºC
CAUTIONS o The usual ones when handling and using
lubricants o Do not mix with different nature greases o Keep containers closed to avoid their
contamination. o We have available MSDS according current EU
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
45
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Industrial Lubricants
Technical Information
Techmol Boot Grease ARMIGRAS 460
HIGH PERFORMANCE SEA WATER RESISTING GREASE
DESCRIPTION Specially formulated grease based semi-synthetic oil, lithium-calcium mixed soap and special additives that provide the grease with high performance.
APPLICATIONS Lubrication of bearings and all type of mechanisms exposed directly to water, salt water and vapour. It has been specially designed to lubricate mechanisms submitted to marine environment.
TYPICAL PHYSICO-CHEMICAL CHARACTERISTICS
Meets with the following standards:
DEF STAN 91-34 (NATO code G-460)
STM 7420-B
THICKENER Lithium-calcium soap
BASE OIL Semi-synthetic
NLGI CONSISTENCY GRADE (DIN 51818) Grade 2
APPEARANCE Brownish grease
WORKED PENETRATION AT 25ºC (ASTM D-217) 280 x 0,1mm
DROPPING POINT (ASTM D-566) 144ºC
PROLONGED WORKED PENETRATION (ASTM D-217) +45 x 0,1mm
WATER WASHOUT, 80ºC (ASTM D-1264) 1,2%
EMCOR CORROSION TEST:
With distilled water
With synthetic salt water
Grade 0
Grade 1 OXIDATION STABILITY, 100ºC (ASTM D-942) 0,35 Kg/cm2
COPPER STRIP CORROSION, 100ºC 1b
4-BALL TEST (IP-239):
Weld load
Wear scar diameter, 1h/40Kg
250 Kg.
0,55mm OIL SEPARATION, 168h/40ºC (IP-121) 2,5%
PUMPABILITY AT -5ºC/24h (DEF STAN 91-34) Pumpable
PROPERTIES
High adherence and sealing High corrosion protection Good load carrying capacity Work temperature: -10 to 110ºC
CAUTIONS o The usual ones when handling and using
lubricants o Do not mix with different nature greases o Keep containers closed to avoid their
contamination. o We have available MSDS according current EU
regulations.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
46
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
Techmol ARMIGRAS 82
GREASE FOR LOW TEMPERATUR
DESCRIPTION
NLGI 2 synthetic calcium soap thickened grease with antioxidant, antirust and EP additives.
APPLICATIONS
It is intended for very low temperature operations (up to -60ºC), meets DEF STAN 91-27
standard and maximum temperature 110ºC.
Very good anticorrosive and EP capacity. Special grease for the car industry and armament, whenever
a good temperature (low andhigh) resistance is needed combined with excellent
anticorrosive properties and good mechanic stabilityMeets DEF. STAN. 91-27/3 (OTAN G-403 Symbol) standard.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
47
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Industrial Lubricants
Techmol ARMIGRAS 82
GREASE FOR LOW TEMPERATURE
Technical Information
DESCRIPTION NLGI 2 synthetic calcium soap thickened grease with antioxidant, antirust and EP additives.
APPLICATIONS It is intended for very low temperature operations (up to -60ºC), meets DEF STAN 91-27 standard and maximum temperature 110ºC. Very good anticorrosive and EP capacity. Special grease for the car industry and armament, whenever a good temperature (low and high) resistance is needed combined with excellent anticorrosive properties and good mechanic stability.
PHYSICAL - CHEMICAL CHARACTERISTICS
HOMOLOGATIONS Meets DEF. STAN. 91-27/3 (OTAN G-403 Symbol) standard.
CAUTIONS - The usual ones when handling and using
lubricants. - Avoid grease excess as well as too frequent
lubrication periods. - Keep the can closed to avoid contamination. - Do not mix with different nature greases.
Drop point, (ºC) Min.130
Worked penetration 60W, (0,1mm) 265 – 295
Worked penetration 105 W, (0,1mm) -10 to +60
Worked penetration 105 W + 10% Water, (0,1mm) -10 to +60 Shell Roll Test, (0,1mm) -25 to +45
Copper corrosion, 24h/100ºC Max. 1b
Test protection against corrosion Grade 1
Oxidation stability, 100h/100ºC, (kPa) Max. 35
Evaporation weight loss, 22h/100ºC, (%) Max. 10
Oil separation, 42h/40ºC, (%) Max. 6
4-balls SHELL device - Load-Wear index, (kg) - Wear scare diameter, 1h/40kg/75ºC, (mm)
Min. 28 Max. 0,70
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Techmol ARMIGRAS 18458
GREASE FOR LOW TEMPERATURE DESCRIPTION
Techmol ARMIGRAS 18458 is a lithium-calcium soap with mineral base oil, high adherence and outstanding anticorrosive performance.
G.A. ARMIGRAS 18458 meets MIL-PRF-18458C ( TYPE I )
APPLICATIONS
G.A. ARMIGRAS 18458 is suggested for wire ropes and exposed gears of hoists, winches, cranes, shovels, dredges, and other similar equipment.
48
Available after consultationin the following Containers:
50g Tube100g Tube200g Tube200g can plastic or metal400g can plastic or metal1000g plastic can900g tin of metal400g Euro cartridge400g LS cartridge500g cartridge
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
49
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Industrial Lubricants
Techmol ARMIGRAS 18458
GREASE FOR LOW TEMPERATURE
Technical Information
DESCRIPTION Techmol ARMIGRAS 18458 is a lithium-calcium soap with mineral base oil, high adherence and outstanding anticorrosive performance. G.A. ARMIGRAS 18458 meets MIL-PRF-18458C ( TYPE I )
APPLICATIONS G.A. ARMIGRAS 18458 is suggested for wire ropes and exposed gears of hoists, winches, cranes, shovels, dredges, and other similar equipment.
PHYSICAL - CHEMICAL CHARACTERISTICS
CAUTIONS The usual ones when handling and using
lubricants. Avoid grease excess as well as too frequent
lubrication periods. Keep the can closed to avoid contamination. Do not mix with different nature greases.
Worked penetration 60W, (0,1mm) 200 - 350
Oil separation, ( FED-STD-791, Method 321 ), (%) < 10
Wear-Load Index ( ASTM D-2596 ) > 30
Adhesivity ( Method PLT L-06 ), (%) > 95
Salt Spray Cabin ( FED-STD-791 ) Pass
Flexibility at low temperature ( Method PLT L-07 ) Pass
Accelerated decomposition ( ASTM G-152,153 ) Pass
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Description Flow grease based on a lithium soap, with highly effective additive packages.
Properties Thanks to highly effective additive packages very resistant to aging, with very good corrosion and wear
protection properties. Ensures a long service life and thus helps to
save maintenance costs. Temperature range –40 °C to +120 °C
Application Particularly suitable for the lubrication of normally stressed roller and plain bearings which operate at low
to normal rotational speeds, also used under dusty and damp condi-tions.
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridge- 400g Lube Shuttle Catridge- 500g Reiner Kartridge
- Special Size available on Request
50
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
51
Product information
Techmol Fließfett L00 K00/000K-40 DIN 51502
Description Flow grease based on a lithium soap, with highly effective
additive packages. Properties Thanks to highly effective additive packages very resistant to
aging, with very good corrosion and wear protection properties. Ensures a long service life and thus helps to save maintenance costs. Temperature range –
40 °C to +120 °C
Characteristic data Brief description K00/000K-40
DIN 51502
NLGI number 00/000
DIN 51818
Worked penetration 400-460 1/10 mm
DIN ISO 2137
Dropping point 165 °C
DIN ISO 2176
Flow pressure at -40 °C
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
52
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridges- 400g Lube Shuttle Catridges- 500g Reiner Cartridges
- Special Size available on request
DescriptionFlow grease based on a lithium soap, with highly effective additive packages as well as EP and adhesive additives.PropertiesThanks to highly effective additive packages very resistant to aging, with very good corrosion and wear protectionproperties. Special high-pressure additives guarantee the use in transmissions even with a high degree of surfacepressure.Temperature range –30 °C to +120 °C
Application Particularly suitable for the lubrication of normally stressed transmissions and gear couplings which operate at low to normal rotational speeds, also used under dusty and damp conditions. Can be used in transmissions in which a semi-li- quid lubricant is particularly effective.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
53
Product information Techmol Fließfett LP00 GP00K-30 DIN 51502
Description Flow grease based on a lithium soap, with highly effective
additive packages as well as EP and adhesive additives. Properties Thanks to highly effective additive packages very resistant to
aging, with very good corrosion and wear protection properties. Special high-pressure additives guarantee the use
in transmissions even with a high degree of surface pressure. Temperature range –
30 °C to +120 °C
Characteristic data Brief description GP00K-30
DIN 51502
NLGI number 00
DIN 51818
Worked penetration 400-430 1/10 mm
DIN ISO 2137
Dropping point 175 °C
DIN ISO 2176
Flow pressure at -35 °C
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
54
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridges- 400g Lube Shuttle Catridges- 500g Reiner Cartridges
- Special Size available on request
Description
Flow grease based on a lithium soap, with highly effective
additive packages as well as EP and adhesive additives.
Properties
Thanks to highly effective additive packages very resistant to
aging, with very good corrosion and wear protection
properties. Special high-pressure additives guarantee the
use in transmissions even with a high degree of surface
pressure.
Temperature range–30 °C to +120 °C
short periods up to +130 °C
Application Particularly suitable for the lubrication of normally stressed transmissions and gear couplings which operate at low to normal rotational speeds, also used under dusty and damp conditions. Can be used in transmissions in which a semi-li- quid lubricant is particularly effective.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
55
Product information Techmol Fließfett LP0 KP0K-30 DIN 51502
Description Flow grease based on a lithium soap, with highly effective
additive packages as well as EP and adhesive additives. Properties Thanks to highly effective additive packages very resistant to
aging, with very good corrosion and wear protection properties. Special high-pressure additives guarantee the use
in transmissions even with a high degree of surface pressure. Temperature range –30 °C to +120 °C short periods up to +130 °C
Characteristic data Brief description KP0K-30
DIN 51502
NLGI number 0
DIN 51818
Worked penetration 355-385 1/10 mm
DIN ISO 2137
Dropping point >160 °C
DIN ISO 2176
Flow pressure at -35 °C
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
56
Description Flow grease based on a sodium soap, with highly effective additive packages. Properties Thanks to highly effective additive packages very resistant to aging, with very good corrosion and wear protection properties. Ensures a long service life and thus helps to save maintenance costs. Temperature range –30 °C to +100 °C
Application Particularly suitable for the lubrication of closed rolling
gears and drum motors at low loads. Its good adhesion is
particularly effective for fast moving transmissions and geared
motors.
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridges- 400g Lube Shuttle Catridges- 500g Reiner Cartridges
- Special Size available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
57
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Product information
Techmol Getriebefließfett NP00
Description Flow grease based on a sodium soap, with highly effective
additive packages. Properties Thanks to highly effective additive packages very resistant to
aging, with very good corrosion and wear protection properties. Ensures a long service life and thus helps to save maintenance costs. Temperature range –
30 °C to +100 °C
Characteristic data Brief description GP00/000H-30
DIN 51502
NLGI number 00/000
DIN 51818
Worked penetration 425-455 1/10 mm
DIN ISO 2137
Dropping point >140 °C
DIN ISO 2176
Flow pressure at -25 °C
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Flow grease based on a sodium soap, with highly effective additive packages. Properties
Thanks to highly effective additive packages very resistant to aging, with very good corrosion and wear protection
properties. Ensures a long service life and thus helps to save maintenance costs.
Temperature range –30 °C to +100 °C Particularly suitable for the lubrication of closed rolling gears and drum motors at low loads. Its good
adhesion is particularly effective for fast moving transmissions and geared motors.
58
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridges- 400g Lube Shuttle Catridges- 500g Reiner Cartridges
- Special Size available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
59
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
Product information
Techmol Getriebefließfett NP0
Description Flow grease based on a sodium soap, with highly effective
additive packages. Properties Thanks to highly effective additive packages very resistant to
aging, with very good corrosion and wear protection properties. Ensures a long service life and thus helps to save maintenance costs. Temperature range –
30 °C to +100 °C
Characteristic data Brief description GP0H-30
DIN 51502
NLGI number 0
DIN 51818
Worked penetration 355-385 1/10 mm
DIN ISO 2137
Dropping point >120 °C
DIN ISO 2176
Flow pressure at -25 °C
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
60
For lubrication of slow running gear boxes; especially oil leaky gears. E.g. for rotary
harrows
sodium soap –20°C to +100°C
GP 0 H-20 ISO-L-XBBBB 0
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridges- 400g Lube Shuttle Catridges- 500g Reiner Cartridges
- Special Size available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
61
Product information
Techmol Getriebefließfett N0
Description Flow grease based on a sodium soap, with highly effective
additive packages. Properties Thanks to highly effective additive packages very resistant to
aging, with very good corrosion and wear protection properties. Ensures a long service life and thus helps to save maintenance costs. Temperature range -
20 °C to +100 °C
Characteristic data Brief description GP0H-20
DIN 51502
NLGI number 0
DIN 51818
Worked penetration 370-420 1/10 mm
DIN ISO 2137
Dropping point >140 °C
DIN ISO 2176
Emcor corrosion class 0/0 DIN 51802
Behavior in the presence of
water
3 DIN 51807 Teil 1
Base oil
Viscosity at 40 °C 220 mm²/s
ASTM D 7042-04
Application
or lubrication of slow running gear boxes; especially oil leaky
gears. E.g. for rotary harrows
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
62
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridges- 400g Lube Shuttle Catridges- 500g Reiner Cartridges
- Special Size available on request
Product description
• work stable, lithium soap fluid grease
• water resistant
• oxidation and corrosion resistant
• free of lead, barium and chlorine
• offers good wear protection
• classification GP 00 K-40 as per DIN 51 826
• classification ISO-L-XDCHB 00 as per ISO/DIS 6743-9
RECOMMENDED IF THE FOLLOWS
FILLING INSTRUCTIONS ARE REQUIRED:
MAN 283 LI-P 00/000
Mercedes Benz 264.0
NLGI 00/000
Central truck lubrication systems from Vogel, MAN and Mercedes
Application
Techmol Fett ZSA is useable in central lubrication systems as well as for gear lubrication. The grease is easily
pumpable even at low temperatures.
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
63
Technical Data Sheet Techmol ZSA GP00 K-40
Product description
• work stable, lithium soap fluid grease • water resistant • oxidation and corrosion resistant • free of lead, barium and chlorine • offers good wear protection • classification GP 00 K-40 as per DIN 51 826 • classification ISO-L-XDCHB 00 as per ISO/DIS 6743-9
Characteristics Colour/Appearance: light green, smooth Thickening agent: Lithium soap Operating temperature range: -40°C - +120°C NLGI-class / DIN 51 818: 00 Base oil viscosity/40°C / DIN 51 562: 68 mm²/s Water content / DIN 51 777/T1: 0,1 %
Dropping point / DIN ISO 2176: > 160 °C
Worked penetration/0.1mm, 60 double strokes / DIN ISO
2137: 430
Worked penetration/0.1mm, 5 000 double strokes / DIN
ISO 2137: 440
Water resistance / DIN 51 807/T1: Evaluation level 1 Flow pressure / DIN 51 805: at -35°C 50 hPa
Oil separation, short test / DIN 51 817: 7,2 %
Corrosion protection behaviour (EMCOR-test) / DIN 51
802: 0/0
Corrosion effect on copper 24h/100°C / DIN 51 811: Corrosion degree 1 Oxidation resistance 100°C/100h / DIN 51 808: 0.2 bar VKA welding load / DIN 51 350/T4: 2400 N
1 / 2 Elastomer test Standard-reference, Elastomer SRE-NBR
34 100°C/7d - Change in hardness / DIN 53 505: -2 Sha
Elastomer test Standard-reference, Elastomer SRE-NBR
34 100°C/7d - Change in volume / DIN 53 521: +6,8 %
RECOMMENDED IF THE FOLLOWS
FILLING INSTRUCTIONS ARE REQUIRED:
MAN 283 LI-P 00/000
Mercedes Benz 264.0
NLGI 00/000
Central truck lubrication systems from Vogel, MAN and Mercedes
Application
Techmol Fett ZSA is useable in central lubrication systems as well as for gear lubrication. The grease is easily pumpable even at low temperatures.
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
Techmol ZSA 000 K-50Synthetic semi-fluid grease intended for use in central lubrication systems of trucks. The product can be used in central lubrication systems in
industrial systems, operating in the open air, with long sections of grease conductors. Due to the use of a synthetic base oil, the grease has very good pump ability at low temperatures. The product contains a set of anti-wear additives and anti-seize additives, which guarantee high
load carrying capacity. The grease is resistant to water and provides very good corrosion resistance.DIESES PRODUKT WIRD VON TechmoL RECOMMENDED IF THE FOLLOWS
FILLING INSTRUCTIONS ARE REQUIRED:GP 00/000 K-50
MAN 283 LI-P 00/000Mercedes Benz 264.0
NLGI 00/000Central truck lubrication systems from Vogel, MAN and Mercedes
64
Avalilable after consultationIn the following Containers:
- 150ml Oblique neck Tube- 250ml Oblique neck Tube- 500ml Oblique neck Tube- 1000ml Oblique neck Tube- 100ml Spout- 250ml Spout- 500ml Spout- 400g Euro Cartridges- 400g Lube Shuttle Catridges- 500g Reiner Cartridges
- Special Size available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
65
Technical Data Sheet Techmol ZSA 000 K-50
Product description
- work stable, lithium soap fluid grease - water resistant - oxidation and corrosion resistant - free of lead, barium and chlorine - offers good wear protection - classification GP 00/000 K-50 as per DIN 51 502
- Specifications: DIN 51502: GP00/000K-50; ISO: L-XECEB00/000
Characteristics Colour/Appearance: bright Thickening agent: Lithium soap Operating temperature range: -40°C - +120°C NLGI-class / DIN 51 818: 00 Base oil viscosity/40°C / DIN 51 562: 47 mm²/s Water content / DIN 51 777/T1: 0,1 %
Dropping point / DIN ISO 2176: > 180 °C
Worked penetration/0.1mm, 5 000 double strokes / DIN
ISO 2137: 446
Water resistance / DIN 51 807/T1: Evaluation level 1
Corrosion effect on copper 24h/100°C / DIN 51 811: Corrosion degree 1 VKA welding load / DIN 51 350/T4: >2000 N
1 / 2
RECOMMENDED IF THE FOLLOWS
FILLING INSTRUCTIONS ARE REQUIRED:
MAN 283 LI-P 00/000
Mercedes Benz 264.0
NLGI 00/000
Central truck lubrication systems from Vogel, MAN and Mercedes
Application
Techmol Fett ZSA is useable in central lubrication systems as well as for gear lubrication. The grease is easily pumpable even at low temperatures.
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
66
Available after consultationin the following Containers:
- 100ml Bottle- 100ml Spout- 1000ml Mix Bottle
Special sizes available on request
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
MINERALÖL-ANWENDUNGSTECHNIK
Techmol 2-Stork Öl
Technische Daten:
Chem. und Physik. Kennda-
ten Einheit Prüfverfahren
MINERALÖL-ANWENDUNGSTECHNIK
2-Takt Öl
Dichte bei 15°C g/ml DIN 517570,870
Flammpunkt °C DIN ISO 2592 185
Pourpoint C°DIN ISO
3016-20
Viscosität bei 40 °C mm² DIN 51562 65
Viskosität bei 100° Cmm²
DIN 51562 9,5
-
Beschreibung:
Ein Motorenöl für alle Zweitaktmotoren mit Gemisch-Schmierung, das auf mineralischen Grundölen mit
Anteilen von HC-Syntheseölen und Syntheseölen basiert. Es verbrennt weitestgehend rückstandsfrei und
raucharm, wodurch die Bildung von Ölkoksrückständen im Verbrennungsraum, in der Kolbenringzone und
in den Steuerschlitzen verhindert wird. Dieses Zweitakt-Öl eignet sich für alle normal belasteten luft- und
wassergekühlten Zweitakt-Benzinmotoren wie Mopeds, Mofas, Rasenmäher, Kettensägen,
Stromaggregaten usw. Auch für Getrenntschmierung geeignet
Spezifikation: SAE30; API; TC
Empfelungen:Global GC; Jaso FC; T.I.S.I.
Teilsyntetisches Zweitaktmotorenöl mit Benzin Stabilisator für Gemisch- und Getrenntschmierung
keine Entmischung
67
All information to the best of our knowledge, but without guarantee. Technical data are average values and are subject to normal production fluctuations
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
68
Available after consultationin the following Containers:
- 100ml Bottle- 250ml Bottle- 500ml Bottle
Special sizes available on request
Techmol Air Hammer Drill Oil/Pneumatic Oil
TPMS24 GmbH & Co.KG - Bahnhofstrasse 35 - 72810 Gomaringen
www.techmol.de - [email protected] - Tel. 07072-922922
MINERALÖL-ANWENDUNGSTECHNIK
Techmol Bohr- und Lufthammeröl - Pneumatiköl
Techmol Air Hammer Drill Oil Universal is a lubricating oil for pneumatic tools and machines. The product is used for the
lubrication of all types of striking and rotating pneumatic tools in the construction industry, in mechanical engineering, in the
workshop area and many other branches of industry, e.g. in compressed air motors, compressed air tippers, compressed air
cylinders, impact weirs, etc.
Techmol drilling and air hammer oil universal view of the sliding and rotating parts from wear and tear and prevents corrosion in
the understanding of tools and mach