Embed Size (px)
Citation preview
![Page 1: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/1.jpg)
GRUNDFOS DATA BOOKLET
SP5A-17 1.5kW 380-415V 50Hz Grundfos pump 5001917
Thank you for your interest in our products. Please contact us for more information, or visit our website
https://www.lenntech.com/grundfos/SPFAM/5001917/SP-5A-17.html
[email protected]. +31 152 610 900 fax. +31 152 616 289
BE > THINK > INNOVATE
![Page 2: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/2.jpg)
Printed from Grundfos Product Centre [2018.06.003]
Position Qty. Description1 SP 5A-17
Note! Product picture may differ from actual product
Product No.: On request
Submersible borehole pump, suitable for pumping clean water. Can be installed vertically orhorizontally. All steel components are made in stainless steel, EN 1.4301 (AISI 304), that ensures highcorrosive resistance. This pump carries drinking water approval.The pump is fitted with a 1.5 kW MS402 motor with sand shield, lip seal, water-lubricated journalbearings and a volume compensating diaphragm. The motor is a canned type submersible motoroffering good mechanical stability and high efficiency. Suitable for temperatures up to 40 °C.The motor is not fitted with a temperature sensor. If temperature monitoring is desired, a Pt1000 sensorcan be fitted.The motor is for direct-on-line starting (DOL).
Further product detailsThe pump is suitable for applications similar to the following:
- raw-water supply- irrigation- groundwater lowering- pressure boosting- fountain applications.
The Grundfos SP pump is renowned for its high efficiency and already complies with the requirementsof the Minimum Efficiency Index, and therefore Grundfos is amongst the best in class withinsubmersible pumps.
PumpAll pump surfaces that are in contact with pumped liquids are made in stainless steel which makesthem corrosion- and wear-resistant. The corrosion diagram below shows the capabilities of the pumpand motor in relation to the temperature in Celsius (y-axis) and the concentration of chloride in ppm(x-axis).
The elastomer parts in the pump are made of NBR (Nitrile-Butadiene Rubber) and TPU (ThermoplasticPoly-Urethane) which offers good wear resistance and long service intervals.
1/10
![Page 3: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/3.jpg)
Printed from Grundfos Product Centre [2018.06.003]
Position Qty. DescriptionThe suction interconnector is fitted with a strainer to prevent large particles from entering the pump. Thesuction interconnector is designed to comply with NEMA standards for motor mounting/dimensions.
MotorThe stator is hermetically encapsulated in stainless steel and the windings are embedded in polymercompound. This results in high mechanical stability, optimum cooling and reduces the risk of shortcircuits in the windings.The shaft seal is of the lip seal type characterised by low friction against the rotor shaft. The NBRelastomer offers good wear resistance, good elasticity and resistance to particles. The rubber materialis approved for use in potable water.The motor can be fitted with a Pt100 or Pt1000 sensor that together with a control unit ensures that themaximum operating temperature conditions are not exceeded.
Liquid:Pumped liquid: WaterMaximum liquid temperature: 40 °CMax liquid t at 0.15 m/sec: 40 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³
Technical:Rated flow: 5 m³/hRated head: 70 mShaft seal for motor: LIPSEALApprovals on nameplate: CE,EACCurve tolerance: ISO9906:2012 3BMotor version: T40
Materials:Pump: Stainless steel
EN 1.4301AISI 304
Impeller: Stainless steelEN 1.4301AISI 304
Motor: Stainless steelDIN W.-Nr. 1.4301AISI 304
Installation:Pump outlet: Rp1 1/2Motor diameter: 4 inch
Electrical data:Motor type: MS402Rated power - P2: 1.5 kWPower (P2) required by pump: 1.5 kWMains frequency: 50 HzRated voltage: 3 x 380-400-415 VRated current: 4.10-4.20-4.40 AStarting current: 490-500-500 %Cos phi - power factor: 0.80-0.75-0.70Rated speed: 2850-2860-2870 rpmStart. method: direct-on-lineEnclosure class (IEC 34-5): IP68Insulation class (IEC 85): BBuilt-in temp. transmitter: no
Others:Minimum efficiency index, MEI ≥: 0.50ErP status: EuP Standalone/Prod.Net weight: 16 kgGross weight: 17.8 kgShipping volume: 16.3 m³
2/10
![Page 4: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/4.jpg)
Printed from Grundfos Product Centre [2018.06.003]
On request SP 5A-17 50 HzH
[m]
0
10
20
30
40
50
60
70
80
90
100
110
Q [m³/h]0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
eta[%]
0
10
20
30
40
50
60
70
80
90
100
SP 5A-17, 3*400 V, 50Hz
P[kW]
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
P1
P2
3/10
![Page 5: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/5.jpg)
Printed from Grundfos Product Centre [2018.06.003]
H[m]
0
10
20
30
40
50
60
70
80
90
100
110
Q [m³/h]0 0.5 1.5 2.5 3.5 4.5 5.5
eta[%]
0
10
20
30
40
50
60
70
80
90
100
SP 5A-17, 3*400 V, 50Hz
P[kW]
0
0.5
1.0
1.5
2.0 P1
P2
859
346
513
101
95
Rp1 1/2
L1
PEWVU
PE
M
L3L2
3
Description ValueGeneral information:Product name: SP 5A-17Product No: On requestEAN number: On requestTechnical:Rated flow: 5 m³/hRated head: 70 mStages: 17Impeller reduc.: NONEShaft seal for motor: LIPSEALApprovals on nameplate: CE,EACCurve tolerance: ISO9906:2012 3BModel: AValve: YESMotor version: T40Materials:Pump: Stainless steel
EN 1.4301AISI 304
Impeller: Stainless steelEN 1.4301AISI 304
Motor: Stainless steelDIN W.-Nr. 1.4301AISI 304
Installation:Pump outlet: Rp1 1/2Motor diameter: 4 inchLiquid:Pumped liquid: WaterMaximum liquid temperature: 40 °CMax liquid t at 0.15 m/sec: 40 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³Electrical data:Motor type: MS402Applic. motor: GRUNDFOSRated power - P2: 1.5 kWPower (P2) required by pump: 1.5 kWMains frequency: 50 HzRated voltage: 3 x 380-400-415 VRated current: 4.10-4.20-4.40 AStarting current: 490-500-500 %Cos phi - power factor: 0.80-0.75-0.70Rated speed: 2850-2860-2870 rpmStart. method: direct-on-lineEnclosure class (IEC 34-5): IP68Insulation class (IEC 85): BMotor protec: NONEThermal protec: externalBuilt-in temp. transmitter: noMotor No: 79192006Others:Minimum efficiency index, MEI ≥: 0.50ErP status: EuP Standalone/Prod.Net weight: 16 kgGross weight: 17.8 kgShipping volume: 16.3 m³
101
95
Rp1 1/2
4/10
![Page 6: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/6.jpg)
Printed from Grundfos Product Centre [2018.06.003]
On request SP 5A-17 50 Hzcos phi
eta
0.0
0.2
0.4
0.6
0.8
P2 [kW]0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8
I[A]
0.0
1.0
2.0
3.0
4.0
SP5A-17 + MS402 1.5 kW 3*400 V, 50 Hz
eta
cos phi
I
n[rpm]
2000
2200
2400
2600
2800
P1[kW]
0.0
1.0
2.0
3.0
4.0n
P1
5/10
![Page 7: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/7.jpg)
Printed from Grundfos Product Centre [2018.06.003]
On request SP 5A-17 50 Hz
Note! All units are in [mm] unless others are stated.Disclaimer: This simplified dimensional drawing does not show all details.
859
346
513
101
95
Rp1 1/2
6/10
![Page 8: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/8.jpg)
Printed from Grundfos Product Centre [2018.06.003]
Exploded view
301a
219
92
7
7a
77
301a
92
11
9
51
100
49
105
45
215a
215
18
217215a
534a534
531531a
28
17
251d
251a
6
11b
66a
67
530530a
7/10
![Page 9: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/9.jpg)
Printed from Grundfos Product Centre [2018.06.003]
Sectional drawing (TM058200 for TPE2,TPE3)
4
2 13
5
TM058200
8/10
![Page 10: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/10.jpg)
Printed from Grundfos Product Centre [2018.06.003]
Exploded view ( TM057026 for MGE model H/I )
251d
251b
290
287277a
286
277
273a
273
268268a289a289
288b288288a
251a
252b
156c
159d
156b
156d188
275a
153
154
158
178
185
192
191
159e
156c 156
151152
266
187
291
293
252a
172
150
287a
502
273b
157
9/10
![Page 11: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/11.jpg)
Printed from Grundfos Product Centre [2018.06.003]
Parts list SP 5A-17, Product No. On requestValid from 1.12.1994 (9448)
Pos Description Annotation Données de classification Référence Quantité Unité- Pump w/o motor 1 pcs
Nut 1Impeller 17Washer 1
- 1 Valve casing cpl. 1Valve casing 1Bearing, top 1
2 Valve cone 13 Valve seat 170 Valve guide 11b Discharge piece 1
- 9 Chamber 16Chamber w/o guide vanes 1Bearing 1
7 Neck ring 1- 10 Chamber, bottom 1
Chamber w/o guide vanes 17 Neck ring 114 Suction interconnector 116 Shaft cpl. Length (mm): 413,5 117 Strap cpl. 318 Cable guard 118.a Pan head screw 226b Hex head screw 364 Priming disc 171 Washer 378 Nameplate 1
- Motor 1 pcsNon return valve cpl. 1
1 Stator cpl. 12 Shaft w/rotor 12a Lock ring 13 Thrust ring support cpl. 15a Radial bearing 122 Staybolt Thread: M8 X M8 425 Cover plate 125a Cross recess countersunk screw 327 Sand shield 174 Socket countersunk screw 120 Motor cable Length (M): 1,7M 1 pcs
10/10
![Page 12: Water Treatment and Purification - Lenntech · 0 0.5 1.5 2.5 3.5 4.5 5.5 Q [m³/h] eta [%] 0 10 20 30 40 50 60 70 80 90 100 SP 5A-17, 3*400 V, 50Hz P [kW] 0 0.5 1.0 1.5 2.0 P1 P2](https://reader034.dokumen.tips/reader034/viewer/2022050602/5faa00c1bda28564d93eb284/html5/thumbnails/12.jpg)
Disclaimer: The information about the Grundfos pump in this document may be outdated. Data may be subject to alterations without further notice. Please contact us to verify the data above is still accurate/up-to-date.
All information is copyright Grundfos.
[email protected]://www.lenntech.comtel. +31 152 610 900 fax. +31 152 616 289
![[XLS] · Web view0 0.2 0.5 1 0 0.02 0.04 0.1 0.2 0.35 0.5 0.7 0.75 1 1.5 2.5 3.7 12.5 0 0.2 0.5 1 0 0.02 0.04 0.1 0.2 0.35 0.5 0.7 0.75 1 1.5 2.5 3.7 12.5 0 0.2 0.5 1 0 0.02 0.04](https://img.dokumen.tips/doc/110x75/5af0fdb97f8b9ac2468eca80/xls-view0-02-05-1-0-002-004-01-02-035-05-07-075-1-15-25-37-125-0.jpg)
![Gabriel Cormier, Ph.D., ing. - Université de Moncton€¦ · H = tf(num,den,-1); pzmap(H); ylim([-1.5 1.5]); Pole-Zero Map Real Axis Imaginary Axis-2.5 -2 -1.5 -1 -0.5 0 0.5 1-1.5-1-0.5](https://img.dokumen.tips/doc/110x75/5eca0b17b65ab576375a8792/gabriel-cormier-phd-ing-universit-de-h-tfnumden-1-pzmaph-ylim-15.jpg)
![1 APPROXIMATION. MOINDRES CARRES. 2 Approcher le graphe de la fonction sur [0,1] par une droite. 00.20.40.60.81 -1.5 -0.5 0 0.5 1 1.5 cos t](https://img.dokumen.tips/doc/110x75/551d9d7e497959293b8b6ac9/1-approximation-moindres-carres-2-approcher-le-graphe-de-la-fonction-sur-01-par-une-droite-0020406081-15-05-0-05-1-15-cos-t.jpg)
![Monique(C.Aller(Georgia(Southern(University)(lana/DUST2016/...–23– Zn Si Mn Fe Cr Ti ) un Solar&Level&(0%&dust)&-2.5 -2 -1.5 -1 -0.5 0 0.5 Metallicity [X/H]-1.5-1-0.5 0 Depletion](https://img.dokumen.tips/doc/110x75/5ffc3ad1c8cbce3a3a2244af/moniquecallergeorgiasouthernuniversity-lanadust2016-a23a-zn-si-mn.jpg)
![Roberto Armellin Œ Francesco Topputo Œ Pierluigi Di Lizia · x 10 11-1.5-1-0.5 0 0.5 1 x 10 11 x [m] y [m]-3 -2 -1 0 1 2 x 10 11-2-1.5-1-0.5 0 0.5 1 1.5 2 x 10 11 x [m] y [m] Interplanetary](https://img.dokumen.tips/doc/110x75/5fc34d69ed9ef8550d54a993/roberto-armellin-francesco-topputo-pierluigi-di-x-10-11-15-1-05-0-05-1.jpg)
