PROFESSIONAL LAUNDRY

WS6-14

14/30 130 595 776 200

7.5 / 10.0 3.0 x x

50 45 50 45 91+23 44+12 114+0 56+0 0.2/0.65/1.45 0.2/0.35/0.75 0.2/- 0.2/- - - 3.2 1.7 58 66 58 66

Washer extractorWS6-14 Compass Pro

Main specificationsMax. capacity filling factor 1:9 kg/lb Drum, volume litre

diameter ø mm Extraction rpm G-factorStandard heating alternatives electricity kW Low energy heating alternatives electricity kW

steam non-heated

Consumption data ”ECO 60°C”*

Total time min Water consumption (cold+hot) litre Energy consumption (motor/heating/hot water) kWh Steam consumption kg Residual moisture %* Water temperature 15°C cold water and 65°C hot water.** Programs with AS.*** Depending on steam pressure.

Images shown are a representation of the product only and variations may occur.

Full load, 14 kg Half load, 7 kg Full load, 14 kg Half load, 7 kg

El Steam***

Produced according to ISO 9001 and ISO 14001.Certified with CB certificate for Low Voltage Directive and S-mark according to the Machinery Directive. Protection class IP X4D.

Washer featuring exceptional savings and effortless use

Priority on peopleCertified ergonomic design with a human-centered approach for an outstanding user experienceCompass Pro® microprocessor offers:• Easy program selection• Language selection• Quick selection and option buttons for the most frequently used wash programs

and options• Wash program packages optimized on Economy, Performance and Time

Long-term savingsExtremely low water and energy consumption – see table below• Automatic Savings weighs the linen and adjusts the water level to the amount of

linen, saving water and energy at less than full load• High extraction force for efficient dewatering• Super Balance guarantees the correct extraction force

Pure controlMonitoring of the status of the equipment and performance from anywhere, allo-wing to take action to improve the business• Washers connectable to OnE Laundry, the personal assistant for hygiene valida-

tion, process management and revenue management

Global Advanced HygieneGlobal Advanced Hygiene program package* with proven log 6 reduction** disinfection of textiles through the laundry process, fulfilling the criteria of all local approved standards

Main options• Automatic liquid detergent supply (optional I/O board)• Savings on chemicals with help of Efficient dosing, both ED peristaltic pumps

and ED Venturi• Connection to booking- /payment- system or coin meter

* Programs available in the standard library of all products, excluding products for specific segments where water temperature is not controllable.** Log 6 reduction equals to 99,999% viral infectivity reduction. The efficacy of reduction of SARS-CoV-2 and other pathogens in the process is confirmed by

RISE (The Research Institute of Sweden) on the basis of Electrolux Professional laboratory data.

WS6-14

3/4 200-600

20751701/2

300-6005

12.9 2.3 ± 3.8

70/56 62/47

5

154 1.02

x x x

720 790 1220 370 440 1335 920 80

1120 215 125 1100 1000 280 105 210

10.0 10.4 20

Experience the Excellencewww.electroluxprofessional.com

A3 1

C

2

E

B

D1 D2

H

LK

IJG

64

9

10

8

F

M O7

N

5

Water and steam connection

Water valves in Water pressure kPa Capacity at 300 kPa l/min Drain valve ø mm Draining capacity l/min Steam valve in Steam pressure kPa Liquid detergent supplies

Floor requirements

Frequency of the dynamic force Hz Floor load at max extraction kN

Sound levels

Sound power/pressure level at extraction* dB(A) Sound power/pressure level at wash* dB(A)

Heat emission

% of installed power, max

Shipping data**

Weight net, kg Shipping volume m3

Accessories

Steel base Hose kits for water or steam Fluff collector

Dimensions in mm

A Width B Depth C Height D1 D2 E F G H I J K L M N O

1 Operating panel 2 Door opening ø 365 mm 3 Detergent box 4 Cold water 5 Hot water 6 Re-used water

7 Drain valve 8 Liquid detergent supply 9 Electrical connection

10 Steam connection

Side view

Rear

Front

Art.

No.

438

9180

13EN

/202

0.11

.20

We

rese

rve

the

right

to a

lter s

pec

ifica

tions

with

out

no

tice.

Electrical connections Heating Main voltage Heating Total Recommended alternative power power fuse

Hz kW kW A

Electric heated

Front and side panels in silver grey and dark blue (color samples can be ordered on part number 472998313).* Sound power levels measured according to ISO 60704.** Average data. Crated weight/shipping volume depends on configuration.

Please contact logistics for exact measures.

415V 3PH N+E** 50

* Total power and recommended fuse does not depend on the heating power in those cases. **with a 5% tolerance range

Electrolux Industrial Washers – S Models – Installation Guideline

All specifications subject to change without notice. Installation Guideline is provided by

Richard Jay Pty Ltd www.richardjay.com.au

Foundations The machine requires a foundation of solid and level concrete construction at least 200 mm deep, 250 to 300mm plinth height is recommended and allows the machine to be raised for simple loading / offloading to meet WHS standards. If a new concrete plinth is to be laid, the old floor must be cutout and new floor installed per below image. The concrete foundation should always be greater in size than the machine and a minimum of 100mm from the edge of the concrete foundation to the edge of the machine must be provided. A metal raising plinth can be used to raise the machine above the drain level for a correct evacuation of water from the machine if required. If block and beam or any other type of floor is present, seek advice.

Fixings A minimum service distance of 750mm is to be provided behind all machines. All machines ship need to chemically bolted to the floor with 2 x M10 and 4 x M16 anchors.

Water Supply The machine is supplied with two or three ¾ inch water inlet hoses, depending on the machine size, 1 or 2 cold and 1 x hot. All water intake connections to the machine should be fitted with manual shut-off valves and filters, to facilitate installation and servicing. Water pipes and hoses should be flushed clean before installation. The machine must be connected with new water hoses, old hoses must not be re-used. Hoses should be an approved type and grade, and comply with IEC 61770. After installation hoses must hang in gentle arcs. All connectors present on the machine must be connected. A minimum supply pressure of 300 kPa and maximum supply pressure of 600 kPa is required. In hard water areas, above 150 PPM, it is recommended that the water supply is fitted with a water softener. Failure to do so will result in detrimental effect on some component parts and may affect the standard warranty.

If the hot water supply is insufficient in temperature, pressure or flow, the machine can then be connected solely to a cold water supply, however will lengthen cycle times. This can only be done if the machine is equipped with a heating source, i.e. electric elements or a steam supply.

Drainage 50mm drain pipe at floor height is required for W5105S, all other machines require 75 mm drain pipe at floor level. This must ensure a downward flow from the machine. Avoid sharp bends which may prevent proper draining. The drainage pipe should be located over a floor drain, drainage channel or the like so that the distance between the outlet and the drain is at least 25 mm.

Electrical In instances where the machine is not equipped with an omni-polar switch, one must be installed beforehand. In accordance with the wiring rules: mount a multi-pole switch prior to the machine to facilitate installation and service operations. The connecting cable should hang in a gentle curve. When connecting to a terminal block, the connection cable shell must be stripped 10-11 mm. The cable area must be at least 0.5 mm2 and no more than 4 mm2.The terminal block used is a spring loaded cage clamp. Each machine must be individually protected. The isolation point for the machine should be in a readily accessible position for use in an emergency. All cabling to the machine must be sufficiently protected against damage. It should be correctly sized to the current rating of the machine and be connected to the machine using a suitable cable entry fixing. Circuit breakers or fuses can be used to protect the power supply. If fuses are used, then they must be of the motor rated variety. A responsible and competent operative should carry out all electrical work and ensure that all local and national regulations and codes of practice are complied with.

Steam (Optional) The machine should be connected to suitably sized live steam supply utilising an isolating valve, strainer/trap, electric solenoid inlet valve and a flexible steam connection hose. (Please note none of these fittings are supplied with the machine). All pipes should be lagged to protect against personal injury. All steam supply pipes should be installed to local and national codes of practice as they form part of a pressurised system.

NOTES:- WHERE EXISTING SERVICES ARE TO BE CONNECTED TO, THE INSTALLER MUST ENSURE THAT THESE ARE ADEQUATELY SIZED AND THAT THEY ARE IN GOOD WORKING ORDER. FOR EXAMPLE, IF A WASHER IS TO BE CONNECTED TO AN EXISTING DRAIN IT MUST BE CHECKED FOR ANY BLOCKAGES DURING INSTALLATION.

FOR MULTIPLE MACHINE INSTALLATIONS SERVICES MUST BE INCREASED IN SIZE ACCORDINGLY. I.E WATER PIPES, DRAINAGE PIPES, ELECTRIC CABLES ETC.

Figure 3 – The machine must be fastened to the floor, making 2 drill holes about 40mm deep (1).

Figure 1 - Casting a plinth - Should be 150-200mm in height

Figure 2 – Breakup existing floor to given dimensions for plinth mold.